Subversion Repositories openrisc_me

#

# Makefile

#   Copyright (C) 1990, 1991, 1992, 1993 ,1994 Free Software Foundation

#

# This file is free software; you can redistribute it and/or modify

# it under the terms of the GNU General Public License as published by

# the Free Software Foundation; either version 2 of the License, or

# (at your option) any later version.

#

# This program is distributed in the hope that it will be useful,

# but WITHOUT ANY WARRANTY; without even the implied warranty of

# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

# GNU General Public License for more details.

#

# You should have received a copy of the GNU General Public License

# along with this program; if not, write to the Free Software

# Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.  */

#

#

# Makefile for newlib/libc/stub/hppa. This is the board support code

# for the HP-PRO hppa embedded boards. 

#

DESTDIR =

VPATH = @srcdir@

srcdir = @srcdir@

objdir = .

srcroot = $(srcdir)/../..

objroot = $(objdir)/../..

prefix = @prefix

exec_prefix = @exec_prefix@

bindir = @bindir@

libdir = @libdir@

tooldir = $(exec_prefix)/$(target_alias)

INSTALL = @INSTALL@

INSTALL_PROGRAM = @INSTALL_PROGRAM@

INSTALL_DATA = @INSTALL_DATA@

SHELL = /bin/sh

CC = @CC@

AS = @AS@

AR = @AR@

LD = @LD@

RANLIB = @RANLIB@

#

# As the boot process only deals with LIF volumes, here's the src

# where we borrow existing code modules and where we put our

# boot image if we can bvuild one.

#

LIF_SRC = /usr/tftpdir/srcboot.lif

LIF_DEST = /usr/tftpdir/romboot.lif

HPDEFS = -D_INCLUDE_POSIX_SOURCE -D_INCLUDE_XOPEN_SOURCE \

         -D_INCLUDE_HPUX_SOURCE -DPCXT

LIBS_FOR_TARGET = -lc

#

# The original flags used by HP for the boot ROMS were

# CFLAGS_FOR_TARGET = -c -Aa +O3 +OS -Wc,-DA1.0 -Wc,-DS1.0 +ESfic +ESsfc ${HPDEFS}

CFLAGS_FOR_TARGET = -c -Wd,-a -g

# the original value for -R was 0

LDFLAGS_FOR_TARGET =  -v -t -N -R 10000 -a archive

INCLUDES = -I${srcdir}

BSP_OBJS= pa_stub.o debugger.o iva_table.o io.o

STUBCRT0=crt0.o

STUBLIB=hppa.o

LDSCRIPT=hppa.ld

SHARED_DIR=

SHARED_OBJS=

# SHARED_OBJS=$(SHARED_DIR)

# Host specific makefile fragment comes in here.

@host_makefile_frag@

all: boot

# this target is only for testing

test: ${STUBCRT0} $(STUBLIB) test.o $(BSP_OBJS)

#       ${LD} $(LDFLAGS_FOR_TARGET) ${STUBCRT0} test.o $(BSP_OBJS) -o test $(LIBS_FOR_TARGET)

        rootme=`pwd` ; \

        ${LD} $(LDFLAGS_FOR_TARGET) ${STUBCRT0} test.o pa_stub.o debugger.o iva_table.o io.o -o test $(LIBS_FOR_TARGET)

$(STUBLIB): $(BSP_OBJS)

        ${LD} -r $(BSP_OBJS) $(SHARED_OBJS) -o $(STUBLIB)

checksum: $(srcdir)/checksum.c

        $(CC) -g $(srcdir)/checksum.c -o checksum

# this is the target from HP's Makefile, it may be bogus

hpstub: $(OBJS)

        $(LD) $(LDFLAGS_FOR_TARGET) -e main -o $@ $(LIBRARY)/crt1.o \

        $(OBJS) -lc -m >stub.map

install:

        $(INSTALL_PROGRAM) $(STUBLIB) $(DESTDIR)$(tooldir)/lib/$(MULTISUBDIR)$(STUBLIB)

        $(INSTALL_PROGRAM) $(SHARED_DIR)/$(STUBCRT0) $(DESTDIR)$(tooldir)/lib/$(MULTISUBDIR)$(STUBCRT0)

        $(INSTALL_PROGRAM) $(srcdir)/$(LDSCRIPT) $(DESTDIR)$(tooldir)/lib/$(LDSCRIPT)

.c.o:

        $(CC) $(CFLAGS_FOR_TARGET) $(INCLUDES) -c $<

.c.s:

        $(CC) $(CFLAGS_FOR_TARGET) -S $(INCLUDES) $<

#       $(CC) $(CFLAGS_FOR_TARGET) $(NEWLIB_CFLAGS) $(INCLUDES) -c $<

.s.o:

        $(CC) $(CFLAGS_FOR_TARGET) $(INCLUDES) -c $<

#       $(AS) $(CFLAGS_FOR_TARGET) $(INCLUDES) -c $<

.SUFFIXES: .S .c .o .s .lif

#

# lifinit --

#       -vnnn   Sets volume size to nnn bytes.

#               nnn must be a multiple of 256.

#       -d      Sets directory size to nnn file entries.

#               nnn must be a multiple of 8.

#       -nsss   Sets the volume name to be sss.

#       -Knnn   Forces the directory start location to be the

#               nearest multiple of nnn x 1024 bytes.

#       -snnn   set the initial system load (ISL) start address to

#               nnn in the volume label

#       -lnnn   Specifies the length in bytes of the ISL code.

#       -ennn   Set the ISL entry point to nnn bytes from the

#               beginning of the ISL

#

# lifcp --

#       -r      Forces RAW mode copying.

#       -T      Sets the file type of the directory entry.

#               ASCII is 1

#               BIN is -23951

#               BINARY is -2

#       -Knnn   forces each file copied in to begin on a nnn x

#               1024-byte boundary from the beginning of the volume

#       Note: the word echoed below MUST be 10 characters exactly.

#

# somxtract infile outfile --

#       converts a series 800 file *only* into a raw image

#

LIF_VOL = this_lif

# 65532

boot: test checksum

#        FIXME: This fills up the hard disk unless "-R" is used

        @rm -f ${LIF_VOL} ${LIF_DEST}

        @ipl_entry=`nm -t d $< | grep "T .START." | sed -e 's/T .START.//' -e 's/^0*//'` ; \

        echo "Entry point is at $${ipl_entry}" ; \

        if test x"$${ipl_entry}" != x  ; then \

        ipl_entry=`expr $${ipl_entry} - 65536` ; \

        echo "Entry point offset is $${ipl_entry}" ; \

        cp $< $<.raw ; \

        rm -f $<.dis ; \

        objdump -d $< > $<.dis ; \

        somxtract $< $<.raw ; \

        ipl_size=`checksum -s $<.raw $<.image  | sed -e 's/ is the.*//'` ; \

        echo "IPL_SIZE is $${ipl_size}" ; \

            lifinit -v64000000 -d64 -n"CYGNUS    " -K2 -s4096 -l$${ipl_size} -e$${ipl_entry} ${LIF_DEST} ;\

            else \

                echo "ERROR: \$$START\$$ symbol not found" ; \

            fi

        @chmod a+rw $<.image

        @lifcp -r -K2 $<.image ${LIF_DEST}:TEST

        @rm -f $<.image $<.dis

        @lifls -l ${LIF_DEST}

        @objdump -d $< > $<.dis

.S.o:

        rm -f $*.s

        ${CPP} $< > $*.s

        $(CC) $(CFLAGS_FOR_TARGET) $(INCLUDES) -c $*.s

#       $(CC) $(CFLAGS_FOR_TARGET) $(NEWLIB_CFLAGS) $(INCLUDES) -c $<

.c.list:

        $(CC) $(CFLAGS) $*.c -S

        $(AS) $(AFLAGS) $*.s -Wa,-l > $*.list

        rm $*.s

.s.list:

        $(AS) $(AFLAGS) $*.s -Wa,-l > $*.list

doc:

clean mostlyclean:

        rm -f *~ *.map *.list stub romboot.lif a.out *.raw *.image

        rm -f *.o $(STUBLIB) $(STUBCRT0) checksum *.dis test

distclean maintainer-clean realclean: clean

        rm -f Makefile config.cache config.log config.status

pa_stub.o:      $(srcdir)/pa_stub.c

debugger.o:     $(srcdir)/debugger.s

iva_table.o:    $(srcdir)/iva_table.s

io.o:           $(srcdir)/io.c

crt0.o:         $(srcdir)/crt0.s

test.o:         $(srcdir)/test.c

term_in.o:      $(srcdir)/term_in.s

term_out.o:     $(srcdir)/term_out.s

term_init.o:    $(srcdir)/term_init.s

.PHONY: info install-info clean-info

info:

install-info:

clean-info:

Makefile: Makefile.in config.status @host_makefile_frag_path@

        $(SHELL) config.status

config.status: configure

        $(SHELL) config.status --recheck