URL https://opencores.org/ocsvn/openrisc_2011-10-31/openrisc_2011-10-31/trunk
Subversion Repositories openrisc_2011-10-31

[/] [openrisc/] [trunk/] [or1ksim/] [peripheral/] [atadevice-cmdi.c] - Blame information for rev 166

Go to most recent revision | Details | Compare with Previous | View Log

/* atadevice_cmdi.c -- ATA Device simulation
   Command interpreter for the simulated harddisk.
 
   Copyright (C) 2002 Richard Herveille, rherveille@opencores.org
   Copyright (C) 2008 Embecosm Limited
 
   Contributor Jeremy Bennett <jeremy.bennett@embecosm.com>
 
   This file is part of Or1ksim, the OpenRISC 1000 Architectural Simulator.
 
   This program is free software; you can redistribute it and/or modify it
   under the terms of the GNU General Public License as published by the Free
   Software Foundation; either version 3 of the License, or (at your option)
   any later version.
 
   This program is distributed in the hope that it will be useful, but WITHOUT
   ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
   FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
   more details.
 
   You should have received a copy of the GNU General Public License along
   with this program.  If not, see <http://www.gnu.org/licenses/>.  */
 
/* This program is commented throughout in a fashion suitable for processing
   with Doxygen. */
 
/* For fun, count the number of FIXMEs :-( */
 
 
/* Autoconf and/or portability configuration */
#include "config.h"
 
/* Package includes */
#include "atadevice-cmdi.h"
#include "atahost.h"
#include "atacmd.h"
#include "sched.h"
 
 
/* FIXME: If device0 is not selected and then an interrupt occurs and
 * then it is selected, the interrupt should be delivered, but I just drop it
 * (same goes for device 1). */
static void
ata_cmd_complete (void *dat)
{
  struct ata_device *dev = dat;
 
  dev->regs.status &= ~ATA_SR_BSY;
 
  if (dev->regs.device_control & ATA_DCR_IEN)
    return;
 
  if ((dev->regs.device_head & ATA_DHR_DEV) != dev->internals.dev)
    return;
 
  if (dev->sigs.intrq)
    return;
 
  dev->sigs.intrq = 1;
  ata_int (dev->internals.host);
}
 
static void
ata_set_sect (struct ata_device *dev, uint32_t sect)
{
  uint16_t cyl;
 
  dev->regs.device_head &= ~ATA_DHR_H;
  if (dev->regs.device_head & ATA_DHR_LBA)
    {
      dev->regs.sector_number = sect & 0xff;
      dev->regs.cylinder_low = (sect >> 8) & 0xff;
      dev->regs.cylinder_high = (sect >> 16) & 0xff;
      dev->regs.device_head |= (sect >> 24) & 0xf;
    }
  else
    {
      cyl = sect / (dev->conf.heads * dev->conf.sectors);
      dev->regs.cylinder_low = cyl & 0xff;
      dev->regs.cylinder_high = (cyl >> 8) & 0xff;
 
      cyl = sect % (dev->conf.heads * dev->conf.sectors);
      dev->regs.sector_number = (cyl % dev->conf.sectors) + 1;
      dev->regs.device_head |= (cyl / dev->conf.sectors) & 0xf;
    }
}
 
/* Returns the concatenated lba address from the values in the addr regs */
static uint32_t
ata_calc_lba (struct ata_device *dev)
{
  uint32_t lba;
 
  /* check if we are using CHS or LBA translation, fill in the bits */
  if (dev->regs.device_head & ATA_DHR_LBA)
    {
      /* we are using LBA translation                               */
      lba = (dev->regs.device_head & ATA_DHR_H) << 24 |
        (dev->regs.cylinder_high) << 16 |
        (dev->regs.cylinder_low) << 8 | dev->regs.sector_number;
    }
  else
    {
      /* we are using CHS translation, calculate lba address        */
      lba = (dev->regs.cylinder_high << 16) | dev->regs.cylinder_low;
      lba *= dev->internals.heads_per_cylinder;
      lba += dev->regs.device_head & ATA_DHR_H;
      lba *= dev->internals.sectors_per_track;
      lba += dev->regs.sector_number;
      lba -= 1;
    }
  return lba;
}
 
/* Reads a sector from the device */
static void
ata_read_sect (struct ata_device *dev)
{
  if (!dev->internals.nr_sect)
    return;
 
  /* set the file-positon pointer to the start of the sector    */
  fseek (dev->conf.stream, dev->internals.lba, SEEK_SET);
 
  /* get the bytes from the stream                              */
  if (1 != fread (dev->internals.dbuf, BYTES_PER_SECTOR, 1, dev->conf.stream))
    {
      printf ("WARNING atadevice read short\n");
    }
 
  /* set status register bits                                   */
  dev->regs.status = ATA_SR_DRDY | ATA_SR_DRQ;
 
  /* reset the databuffer                                       */
  dev->internals.dbuf_cnt = BYTES_PER_SECTOR / 2;       //Words, not bytes
  dev->internals.dbuf_ptr = dev->internals.dbuf;
 
  dev->internals.lba += BYTES_PER_SECTOR;
  dev->internals.nr_sect--;
 
  SCHED_ADD (ata_cmd_complete, dev, 400000);
}
 
/* Writes a sector to the device */
static void
ata_write_sect (struct ata_device *dev)
{
  if (!dev->internals.nr_sect)
    {
      dev->regs.status = ATA_SR_DRDY;
      return;
    }
 
  /* set the file-positon pointer to the start of the sector    */
  fseek (dev->conf.stream, dev->internals.lba, SEEK_SET);
 
  /* get the bytes from the stream                              */
  fwrite (dev->internals.dbuf, BYTES_PER_SECTOR, 1, dev->conf.stream);
 
  /* set status register bits                                   */
  dev->regs.status = ATA_SR_DRDY | ATA_SR_DRQ | ATA_SR_DSC | ATA_SR_BSY;
 
  /* reset the databuffer                                       */
  dev->internals.dbuf_cnt = BYTES_PER_SECTOR / 2;       //Words, not bytes
  dev->internals.dbuf_ptr = dev->internals.dbuf;
 
  dev->internals.lba += BYTES_PER_SECTOR;
  if (!--dev->internals.nr_sect)
    dev->regs.status = ATA_SR_DRDY | ATA_SR_DSC | ATA_SR_BSY;
 
  SCHED_ADD (ata_cmd_complete, dev, 40000);
}
 
 
/*
  A T A _ S E T _ D E V I C E _ S I G N A T U R E
 
  called whenever a command needs to signal the device type (packet, non-packet)
*/
static void
ata_set_device_signature (struct ata_device *device, int packet)
{
  if (packet)
    {
      /* place PACKET Command feature set signature in register block   */
      device->regs.sector_count = 0x01;
      device->regs.sector_number = 0x01;
      device->regs.cylinder_low = 0x14;
      device->regs.cylinder_high = 0xEB;
    }
  else
    {
      /* place NON_PACKET Command feature set signature in register block */
      device->regs.sector_count = 0x01;
      device->regs.sector_number = 0x01;
      device->regs.cylinder_low = 0x00;
      device->regs.cylinder_high = 0x00;
      device->regs.device_head = 0x00;
    }
}
 
 
/*
  A T A _ E X E C U T E _ D E V I C E _ D I A G N O S T I C S
*/
void
ata_execute_device_diagnostics_cmd (struct ata_device *device)
{
  /* clear SRST bit, if set                                           */
  device->regs.device_control &= ~ATA_DCR_RST;
 
  /* content of features register is undefined                        */
 
  /*
     set device error register
     Device0: 0x01 = Device0 passed & Device1 passed/not present
     Device1: 0x01 = Device1 passed
   */
  device->regs.error = 0x01;
  /* something about DASP- and error_register_bit7                    */
  /* if device1 is not present or if device1 is present and passed    */
  /* diagnostics, than bit7 should be cleared.                        */
  /* This means we always clear bit7                                  */
 
 
  /* check if device implements packet protocol                       */
  if (device->conf.packet)
    {
      /* place PACKET command feature set signature in register block   */
      ata_set_device_signature (device, 1);
 
      device->regs.status &= 0xf8;
 
      if (device->regs.command == DEVICE_RESET)
        device->regs.device_head = device->regs.device_head & ATA_DHR_LBA;
      else
        device->regs.device_head = 0x00;
    }
  else
    {
      /* place NON_PACKET Command feature set signature in register block */
      ata_set_device_signature (device, 0);
 
      device->regs.status &= 0x82;
    }
 
 
  /* we passed diagnostics, so set the PDIAG-line                     */
  device->sigs.pdiago = 1;
}
 
 
/*
  A T A _ D E V I C E _ R E S E T
*/
static void
ata_device_reset_cmd (struct ata_device *device)
{
  if (!device->conf.packet)
    {
      fprintf( stderr, "Warning: executing DEVICE_RESET on non-packet "
               "device\n");
    }
 
  ata_execute_device_diagnostics_cmd (device);
}
 
 
/*
  A T A _ I D E N T I F Y _ D E V I C E
*/
static void
ata_identify_device_cmd (struct ata_device *device)
{
  unsigned char *chksum_buf, chksum;
  unsigned short *buf;
  int n;
  unsigned int tmp;
 
  /* reset databuffer                                                 */
  device->internals.dbuf_cnt = 256;
  device->internals.dbuf_ptr = device->internals.dbuf;
  device->internals.end_t_func = NULL;
 
  buf = device->internals.dbuf;
  chksum_buf = (unsigned char *) buf;
 
  /*
     if number_of_available_sectors (==device->size / BYTES_PER_SECTOR) < 16,514,064 then
     support CHS translation where:
     LBA = ( ((cylinder_number*heads_per_cylinder) +head_number) *sectors_per_track ) +sector_number -1;
 
     Cylinders : 1-255   (or max.cylinders)
     Heads     : 0-15    (or max.heads    )
     Sectors   : 0-65535 (or max.sectors  )
   */
 
  /*
     1) Word 1 shall contain the number of user-addressable logical cylinders in the default CHS
     translation. If the content of words (61:60) is less than 16,514,064 then the content of word 1
     shall be greater than or equal to one and less than or equal to 65,535. If the content of words
     (61:60) is greater than or equal to 16,514,064 then the content of
     word 1 shall be equal to 16,383.
     2) Word 3 shall contain the number of user-addressable logical heads in the default CHS
     translation. The content of word 3 shall be greater than or equal to one and less than or equal to
     16. For compatibility with some BIOSs, the content of word 3 may be equal to 15 if the content of
     word 1 is greater than 8192.
     3) Word 6 shall contain the number of user-addressable logical sectors in the default CHS
     translation. The content of word 6 shall be greater than or equal to one and less than or equal to
     63.
     4) [(The content of word 1) * (the content of word 3) * (the content of word 6)] shall be less than or
     equal to 16,514,064
     5) Word 54 shall contain the number of user-addressable logical cylinders in the current CHS
     translation. The content of word 54 shall be greater than or equal to one and less than or
     equal to 65,535. After power-on of after a hardware reset the content of word 54 shall be equal to
     the content of word 1.
     6) Word 55 shall contain the number of user-addressable logical heads in the current CHS
     translation. The content of word 55 shall be greater than or equal to one and less than or equal
     to 16. After power-on or after a hardware reset the content of word 55 shall equal the content of
     word 3.
     7) Word 56 shall contain the user-addressable logical sectors in the current CHS
     translation. The content of word 56 should be equal to 63 for compatibility with all BIOSs.
     However, the content of word 56 may be greater than or equal to one and less than or equal to
     255. At power-on or after a hardware reset the content of word 56 shall equal the content of
     word 6.
     8) Words (58:57) shall contain the user-addressable capacity in sectors for the current CHS
     translation. The content of words (58:57) shall equal [(the content of word 54) * (the content of
     word 55) * (the content of word 56)] The content of words (58:57) shall be less than or equal to
     16,514,064. The content of words (58:57) shall be less than or equal to the content of words
     (61:60).
     9) The content of words 54, 55, 56, and (58:57) may be affected by the host issuing an INITIALIZE
     DEVICE PARAMETERS command.
     10)If the content of words (61:60) is greater than 16,514,064 and if the device does not support CHS
     addressing, then the content of words 1, 3, 6, 54, 55, 56, and (58:57) shall equal zero. If the
     content of word 1, word 3, or word 6 equals zero, then the content of words 1, 3, 6, 54, 55, 56,
     and (58:57) shall equal zero.
     11)Words (61:60) shall contain the total number of user-addressable sectors. The content of words
     (61:60) shall be greater than or equal to one and less than or equal to 268,435,456.
     12)The content of words 1, 54, (58:57), and (61:60) may be affected by the host issuing a SET MAX
     ADDRESS command.
   */
 
 
  /* check if this is a NON-PACKET device                             */
  if (device->conf.packet)
    {
      /*
         This is a PACKET device.
         Respond by placing PACKET Command feature set signature in block registers.
         Abort command.
       */
 
      ata_set_device_signature (device, 1);
      device->regs.status = ATA_SR_ERR;
      device->regs.error = ATA_ERR_ABT;
    }
  else
    {
      /* start filling buffer                                           */
 
      /*
         word 0: General configuration
         15  : 0 = ATA device
         14-8: retired
         7   : 1 = removable media device (not set)
         6   : 1 = not-removable controller and/or device (set)
         5-0 : retired and/or always set to zero
       */
      *buf++ = 0x0040;
 
      /*
         word 1: Number of logical cylinders
 
         >=1, <= 65535
       */
      if ((tmp = device->conf.size_sect) >= 16514064)
        *buf++ = 16383;
      else
        if ((tmp /= (device->conf.heads + 1) * device->conf.sectors) > 65535)
        *buf++ = 65535;
      else
        *buf++ = tmp;
 
      /*
         word 2: Specific configuration
 
         0x37c8: Device requires SET_FEATURES subcommand to spinup after power-on
         and IDENTIFY_DEVICE response is incomplete
         0x738c: Device requires SET_FEATURES subcommand to spinup after power-on
         and IDENTIFY_DEVICE response is complete
         0x8c73: Device does not require SET_FEATURES subcommand to spinup after power-on
         and IDENTIFY_DEVICE response is incomplete
         0xc837: Device does not require SET_FEATURES subcommand to spinup after power-on
         and IDENTIFY_DEVICE response is complete
 
         pick-one
       */
      *buf++ = 0xc837;
 
      /*
         word 3: Number of logical heads
 
         >= 1, <= 16
 
         set to 15 if word1 > 8192 (BIOS compatibility)
       */
      *buf++ = device->conf.heads;
 
      /*
         word 5-4: retired
       */
      buf += 2;
 
      /*
         word 6: Number of logical sectors per logical track
 
         >= 1, <= 63
       */
      *buf++ = device->conf.sectors;
 
      /*
         word 8-7: Reserved by the CompactFLASH association
       */
      buf += 2;
 
      /*
         word 9: retired
       */
      buf++;
 
      /*
         word 19-10: Serial number (ASCII)
       */
      /*           " www.opencores.org  "                               */
      *buf++ = (' ' << 8) | 'w';
      *buf++ = ('w' << 8) | 'w';
      *buf++ = ('.' << 8) | 'o';
      *buf++ = ('p' << 8) | 'e';
      *buf++ = ('n' << 8) | 'c';
      *buf++ = ('o' << 8) | 'r';
      *buf++ = ('e' << 8) | 's';
      *buf++ = ('.' << 8) | 'o';
      *buf++ = ('r' << 8) | 'g';
      *buf++ = (' ' << 8) | ' ';
 
      /*
         word 22   : obsolete
         word 21-20: retired
       */
      buf += 3;
 
      /*
         word 26-23: Firmware revision
       */
      strncpy ((char *) buf, device->conf.firmware, 8);
      buf += 4;
 
      /*
         word 46-27: Model number
       */
      /*           " ata device model  (C)Richard Herveille "           */
      *buf++ = (' ' << 8) | 'a';
      *buf++ = ('t' << 8) | 'a';
      *buf++ = (' ' << 8) | 'd';
      *buf++ = ('e' << 8) | 'v';
      *buf++ = ('i' << 8) | 'c';
      *buf++ = ('e' << 8) | ' ';
      *buf++ = ('m' << 8) | 'o';
      *buf++ = ('d' << 8) | 'e';
      *buf++ = ('l' << 8) | ' ';
      *buf++ = (' ' << 8) | '(';
      *buf++ = ('C' << 8) | ')';
      *buf++ = ('R' << 8) | 'i';
      *buf++ = ('c' << 8) | 'h';
      *buf++ = ('a' << 8) | 'r';
      *buf++ = ('d' << 8) | ' ';
      *buf++ = ('H' << 8) | 'e';
      *buf++ = ('r' << 8) | 'v';
      *buf++ = ('e' << 8) | 'i';
      *buf++ = ('l' << 8) | 'l';
      *buf++ = ('e' << 8) | ' ';
 
      /*
         word 47:
         15-8: 0x80
         7-0: 0x00 reserved
         0x01-0xff maximum number of sectors to be transfered
         per interrupt on a READ/WRITE MULTIPLE command
       */
      *buf++ = 0x8001;
 
      /*
         word 48: reserved
       */
      buf++;
 
      /*
         word 49: Capabilities
         15-14: reserved for IDENTIFY PACKET DEVICE
         13   : 1=standby timers are supported
         0=standby timers are handled by the device FIXME
         12   : reserved for IDENTIFY PACKET DEVICE
         11   : 1=IORDY supported
         0=IORDY may be supported
         10   : 1=IORDY may be disabled
         9   : set to one
         8   : set to one
         7-0 : retired
       */
      *buf++ = 0x0f00;
 
      /*
         word 50: Capabilities
         15  : always cleared to zero
         14  : always set to one
         13-1: reserved
 
       */
      *buf++ = 0x4000;
 
      /*
         word 52-51: obsolete
       */
      buf += 2;
 
      /*
         word 53:
         15-3: Reserved
         2   : 1=value in word 88 is valid
         0=value in word 88 is not valid
         1   : 1=value in word 64-70 is valid
         0=value in word 64-70 is not valid
 
         0=value in word 54-58 is not valid
       */
      *buf++ = 0x0007;
 
 
      /*
         word 54: number of current logical cylinders (0-65535)
       */
      if ((tmp = device->conf.size_sect) > 16514064)
        tmp = 16514064;
 
      tmp /= (device->internals.heads_per_cylinder +
              1) * (device->internals.sectors_per_track);
      if (tmp > 65535)
        *buf++ = 65535;
      else
        *buf++ = tmp;
 
      /*
         word 55: number of current logical heads, (0-15)
       */
      *buf++ = device->internals.heads_per_cylinder + 1;
 
      /*
         word 56: number of current logical sectors per track (1-255)
       */
      *buf++ = device->internals.sectors_per_track;
 
      /*
         word 58-57: current capacity in sectors
       */
      tmp = *(buf - 3) * *(buf - 2) * *(buf - 1);
      *buf++ = tmp >> 16;
      *buf++ = tmp & 0xffff;
 
      /*
         word 59:
         15-9: reserved
         8   : 1=multiple sector setting is valid
         7-0 : current setting for number of sectors to be transfered
         per interrupt on a READ/WRITE MULTIPLE command
       */
      *buf++ = 0x0001;          // not really a FIXME
 
      /*
         word 60-61: Total number of user addressable sectors (LBA only)
       */
      *buf++ = device->conf.size_sect;
      *buf++ = device->conf.size_sect >> 16;
 
      /*
         word 62: obsolete
       */
      buf++;
 
      /* FIXME
         word 63: DMA settings
         15-11: Reserved
         10   : 1=Multiword DMA Mode 2 is selected
         0=Multiword DMA Mode 2 is not selected
         9   : 1=Multiword DMA Mode 1 is selected
         0=Multiword DMA Mode 1 is not selected
         8   : 1=Multiword DMA Mode 0 is selected
         0=Multiword DMA Mode 0 is not selected
         7-3 : Reserved
         2   : Multiword DMA Mode 2 and below are supported
         1   : Multiword DMA Mode 1 and below are supported
 
       */
      *buf = 0;
      if (device->conf.mwdma >= 0)
        *buf |= 0x1;
      if (device->conf.mwdma >= 1)
        *buf |= 0x2;
      if (device->conf.mwdma >= 2)
        *buf |= 0x4;
 
      buf++;
 
      /*
         word 64:
         15-8: reserved
         7-0: Advanced PIO modes supported
 
         7-2: reserved
         1  : PIO mode4 supported
 
       */
      *buf = 0;
      if (device->conf.pio >= 3)
        *buf |= 0x1;
      if (device->conf.pio >= 4)
        *buf |= 0x2;
      buf++;
 
      /*
         word 65: Minimum Multiword DMA transfer cycle time per word (nsec)
       */
      *buf++ = MIN_MWDMA_CYCLE_TIME;
 
      /*
         word 66: Manufacturer's recommended Multiword DMA transfer cycle time per word (nsec)
       */
      *buf++ = RECOMMENDED_MWDMA_CYCLE_TIME;
 
 
      /*
         word 67: Minimum PIO transfer cycle time per word (nsec), without IORDY flow control
       */
      *buf++ = MIN_PIO_CYCLE_TIME_NO_IORDY;
 
      /*
         word 68: Minimum PIO transfer cycle time per word (nsec), with IORDY flow control
       */
      *buf++ = MIN_PIO_CYCLE_TIME_IORDY;
 
      /*
         word 69-70: reserved for future command overlap and queueing
         71-74: reserved for IDENTIFY PACKET DEVICE command
       */
      buf += 6;
 
      /*
         word 75: Queue depth
         15-5: reserved
         4-0: queue depth -1
       */
      *buf++ = SUPPORT_READ_WRITE_DMA_QUEUED ? QUEUE_DEPTH : 0x0000;
 
      /*
         word 76-79: reserved
       */
      buf += 4;
 
      /*
         word 80: MAJOR ATA version
         We simply report that we do not report a version
 
         You can also set bits 5-2 to indicate compliancy to
         ATA revisions 5-2 (1 & 0 are obsolete)
       */
      *buf++ = 0x0000;
 
      /*
         word 81: MINOR ATA version
         We report ATA/ATAPI-5 T13 1321D revision 3 (0x13)
       */
      *buf++ = 0x0013;
 
      /*
         word 82: Command set supported
       */
      *buf++ = 0 << 15 | /* obsolete        */
        SUPPORT_NOP_CMD << 14 | SUPPORT_READ_BUFFER_CMD << 13 | SUPPORT_WRITE_BUFFER_CMD << 12 | 0 << 11 |       /* obsolete        */
        SUPPORT_HOST_PROTECTED_AREA << 10 | SUPPORT_DEVICE_RESET_CMD << 9 | SUPPORT_SERVICE_INTERRUPT << 8 | SUPPORT_RELEASE_INTERRUPT << 7 | SUPPORT_LOOKAHEAD << 6 | SUPPORT_WRITE_CACHE << 5 | 0 << 4 |       /* cleared to zero */
        SUPPORT_POWER_MANAGEMENT << 3 |
        SUPPORT_REMOVABLE_MEDIA << 2 |
        SUPPORT_SECURITY_MODE << 1 | SUPPORT_SMART << 0;
 
      /*
         word 83: Command set supported
       */
      *buf++ = 0 << 15 | /* cleared to zero */
        1 << 14 |               /* set to one      */
 
        SUPPORT_SET_MAX << 8 | 0 << 7 |  /* reserved for    */
        /* project 1407DT  */
        SET_FEATURES_REQUIRED_AFTER_POWER_UP << 6 |
        SUPPORT_POWER_UP_IN_STANDBY_MODE << 5 |
        SUPPORT_REMOVABLE_MEDIA_NOTIFICATION << 4 |
        SUPPORT_APM << 3 |
        SUPPORT_CFA << 2 |
        SUPPORT_READ_WRITE_DMA_QUEUED << 1 | SUPPORT_DOWNLOAD_MICROCODE << 0;
 
      /*
         word 84: Command set/feature supported
       */
      *buf++ = 0 << 15 | /* cleared to zero */
        1 << 14                 /* set to one      */
        ;                       /* 0-13 reserved   */
 
      /*
         word 85: Command set enabled FIXME
       */
      *buf++ = 0 << 15 | /* obsolete        */
        SUPPORT_NOP_CMD << 14 | SUPPORT_READ_BUFFER_CMD << 13 | SUPPORT_WRITE_BUFFER_CMD << 12 | 0 << 11 |       /* obsolete        */
        SUPPORT_HOST_PROTECTED_AREA << 10 | SUPPORT_DEVICE_RESET_CMD << 9 | SUPPORT_SERVICE_INTERRUPT << 8 | SUPPORT_RELEASE_INTERRUPT << 7 | SUPPORT_LOOKAHEAD << 6 | SUPPORT_WRITE_CACHE << 5 | 0 << 4 |       /* cleared to zero */
        SUPPORT_POWER_MANAGEMENT << 3 |
        SUPPORT_REMOVABLE_MEDIA << 2 |
        SUPPORT_SECURITY_MODE << 1 | SUPPORT_SMART << 0;
 
      /*
         word 86: Command set enables
       */
      *buf++ = 0 << 9 |          /* 15-9 reserved   */
        SUPPORT_SET_MAX << 8 | 0 << 7 |  /* reserved for    */
        /* project 1407DT  */
        SET_FEATURES_REQUIRED_AFTER_POWER_UP << 6 |
        SUPPORT_POWER_UP_IN_STANDBY_MODE << 5 |
        SUPPORT_REMOVABLE_MEDIA_NOTIFICATION << 4 |
        SUPPORT_APM << 3 |
        SUPPORT_CFA << 2 |
        SUPPORT_READ_WRITE_DMA_QUEUED << 1 | SUPPORT_DOWNLOAD_MICROCODE << 0;
 
      /*
         word 87: Command set/feature supported
       */
      *buf++ = 0 << 15 | /* cleared to zero */
        1 << 14                 /* set to one      */
        ;                       /* 0-13 reserved   */
 
      /*
         word 88: UltraDMA section
         15-13: reserved
         12   : 1=UltraDMA Mode 4 is selected
         0=UltraDMA Mode 4 is not selected
         10   : 1=UltraDMA Mode 3 is selected
         0=UltraDMA Mode 3 is not selected
         10   : 1=UltraDMA Mode 2 is selected
         0=UltraDMA Mode 2 is not selected
         9   : 1=UltraDMA Mode 1 is selected
         0=UltraDMA Mode 1 is not selected
         8   : 1=UltraDMA Mode 0 is selected
         0=UltraDMA Mode 0 is not selected
         7-5 : Reserved
         4   : UltraDMA Mode 4 and below are supported
         3   : UltraDMA Mode 3 and below are supported
         2   : UltraDMA Mode 2 and below are supported
         1   : UltraDMA Mode 1 and below are supported
 
 
         Because the OCIDEC cores currently do not support
         UltraDMA we set all bits to zero
       */
      *buf++ = 0;
 
      /*
         word 89: Security sector erase unit completion time
 
         For now we report a 'value not specified'.
       */
      *buf++ = 0x0000;          // not really a FIXME
 
      /*
         word 90: Enhanced security erase completion time
 
         For now we report a 'value not specified'.
       */
      *buf++ = 0x0000;          // not really a FIXME
 
      /*
         word 91: Current advanced power management value
 
         For now set it to zero.
       */
      *buf++ = 0x0000;          // FIXME
 
      /*
         word 92: Master Password Revision Code.
         We simply report that we do not support this.
       */
      *buf++ = 0x0000;
 
      /*
         word 93: Hardware reset result
       */
      if (device->internals.dev)
        {
          /* this is device1, clear device0 bits                                         */
          *buf++ = 0 << 15 | 1 << 14 | 0 << 13 |  /* CBLIBD level (1=Vih, 0=Vil)               */
            /* 12-8 Device 1 hardware reset result       */
 
            device->sigs.pdiago << 11 | /* 1: Device1 did assert PDIAG               */
            /* 0: Device1 did not assert PDIAG           */
            3 << 9 |            /* Device1 determined device number by       */
            /* 00: reserved                              */
            /* 01: a jumper was used                     */
            /* 10: the CSEL signal was used              */
            /* 11: some other or unknown method was used */
            1 << 8              /* set to one                                */
            ;
        }
      else
        {                       /* FIXME bit 6 */
          /* this is device0, clear device1 bits                                         */
          *buf++ = 0 << 7 |      /* reserved                                  */
 
            /* 0: Device0 does not respond for device1   */
            device->sigs.daspi << 5 |   /* 1: Device0 did detected DASP assertion    */
            /* 0: Device0 did not detect DASP assertion  */
            device->sigs.pdiagi << 4 |  /* Device0 did detect PDIAG assertion        */
            /* Device0 did not detect PDIAG assertion    */
            1 << 3 |            /* Device0 did pass diagnostics              */
            3 << 1 |            /* Device0 determined device number by       */
            /* 00: reserved                              */
            /* 01: a jumper was used                     */
            /* 10: the CSEL signal was used              */
            /* 11: some other or unknown method was used */
            1 << 0               /* set to one                                */
            ;
        }
 
      /*
         word 94-126: Reserved
       */
      buf += 33;
 
      /*
         word 127: Removable Media Status Notification feature set support
         15-2: reserved
         1-0: 00 Removable media Status Notification not supported
         01 Removable media Status Notification supported
         10 reserved
         11 reserved
       */
      *buf++ = SUPPORT_REMOVABLE_MEDIA_NOTIFICATION;
 
      /*
         word 128: Security status
         15-9: reserved
         8   : Security level, 0=high, 1=maximum
         7-6 : reserved
         5   : 1=enhanced security erase supported
         4   : 1=security count expired
         3   : 1=security frozen
         2   : 1=security locked
         1   : 1=security enabled
 
 
         for now we do not support security, set is to zero
       */
      *buf++ = 0;
 
      /*
         word 129-159: Vendor specific
       */
      buf += 31;
 
      /*
         word 160: CFA power mode 1
         15  : Word 160 supported
         14  : reserved
         13  : CFA power mode 1 is required for one or more commands
         12  : CFA power mode 1 disabled
         11-0: Maximum current in mA
       */
      *buf++ = 0;
 
      /*
         word 161-175: Reserved for the CompactFLASH Association
       */
      buf += 15;
 
      /*
         word 176-254: reserved
       */
      buf += 79;
 
      /*
         word 255: Integrity word
         15-8: Checksum
         7-0 : Signature
       */
      // set signature to indicate valid checksum
      *buf = 0x00a5;
 
      // calculate checksum
      chksum = 0;
      for (n = 0; n < 511; n++)
        chksum += *chksum_buf++;
 
      *buf = ((0 - chksum) << 8) | 0x00a5;
 
      /* set status register bits                                       */
      device->regs.status = ATA_SR_DRDY | ATA_SR_DRQ;
    }
}
 
 
/*
  A T A _ I N I T I A L I Z E _ D E V I C E _ P A R A M E T E R S
*/
static void
ata_initialize_device_parameters_cmd (struct ata_device *device)
{
  device->internals.sectors_per_track = device->regs.sector_count;
  device->internals.heads_per_cylinder = device->regs.device_head & ATA_DHR_H;
 
  /* set status register bits                                         */
  device->regs.status = ATA_SR_BSY | ATA_SR_DRDY;
}
 
 
/*
  A T A _ R E A D _ S E C T O R S
*/
static void
ata_read_sectors_cmd (struct ata_device *device)
{
  size_t sector_count;
  uint32_t lba;
 
  /* check if this is a NON-PACKET device                             */
  if (device->conf.packet)
    {
      /*
         This is a PACKET device.
         Respond by placing PACKET Command feature set signature in block registers.
         Abort command.
       */
      ata_set_device_signature (device, 1);
      device->regs.status = ATA_SR_ERR | ATA_SR_DRDY;
      device->regs.error = ATA_ERR_ABT;
      return;
    }
 
  /* get the sector count                                           */
  if (device->regs.sector_count == 0)
    sector_count = 256;
  else
    sector_count = device->regs.sector_count;
 
  lba = ata_calc_lba (device);
 
  /* check if sector within bounds                                  */
  if (lba >= device->conf.size_sect)
    {
      /* invalid sector address                                     */
      /* set the status & error registers                           */
      device->regs.status = ATA_SR_DRDY | ATA_SR_ERR;
      device->regs.error = ATA_ERR_IDNF;
      return;
    }
 
  /* go ahead, read the bytestream                              */
  lba *= BYTES_PER_SECTOR;
 
  device->internals.lba = lba;
  device->internals.nr_sect = sector_count;
  device->internals.end_t_func = ata_read_sect;
 
  ata_read_sect (device);
}
 
 
 
/*
  A T A _ R E A D _ N A T I V E _ M A X _ A D D R
*/
static void
ata_read_native_max_addr (struct ata_device *dev)
{
  // FIXME: Left shift????
  ata_set_sect (dev, dev->conf.size << 11);
 
  dev->regs.status = ATA_SR_DRDY | ATA_SR_BSY;
}
 
/*
  A T A _ W R I T E _ S E C T O R S
*/
static void
ata_write_sectors (struct ata_device *dev)
{
  size_t sector_count;
  uint32_t lba;
 
  if (dev->conf.packet)
    {
      ata_set_device_signature (dev, 1);
      dev->regs.status = ATA_SR_ERR | ATA_SR_DRDY;
      dev->regs.error = ATA_ERR_ABT;
      return;
    }
 
  /* get the sector count                                           */
  if (dev->regs.sector_count == 0)
    sector_count = 256;
  else
    sector_count = dev->regs.sector_count;
 
  lba = ata_calc_lba (dev);
 
  /* check if sector within bounds                                  */
  if (lba >= dev->conf.size_sect)
    {
      /* invalid sector address                                     */
      /* set the status & error registers                           */
      dev->regs.status = ATA_SR_DRDY | ATA_SR_ERR;
      dev->regs.error = ATA_ERR_IDNF;
      return;
    }
 
  dev->internals.lba = lba * BYTES_PER_SECTOR;
  dev->internals.nr_sect = sector_count;
 
  dev->internals.dbuf_cnt = BYTES_PER_SECTOR / 2;       //Words, not bytes
  dev->internals.dbuf_ptr = dev->internals.dbuf;
 
  dev->regs.status = ATA_SR_BSY | ATA_SR_DRDY | ATA_SR_DRQ;
  dev->internals.end_t_func = ata_write_sect;
}
 
/*
  A T A _ S E T _ F E A T U R E S
*/
static void
ata_set_features (struct ata_device *dev)
{
  switch (dev->regs.features)
    {
    case SET_TRANSFER_MODE_SECTOR_COUNT_REG:
      /* FIXME: I don't have a clue as to what to do with this... */
      switch (dev->regs.sector_count >> 3)
        {
        case 0:          /* Set default */
          break;
        case 1:         /* Set PIO mode */
          break;
        case 4:         /* Set DMA mode */
          /* FIXME */
          fprintf (stderr, "Fixme: Set DMA mode to %d\n",
                   dev->regs.sector_count & 0x7);
          break;
        case 8:         /* Set UDMA mode */
          /* FIXME */
          fprintf (stderr, "Fixme: Set UDMA mode to %d\n",
                   dev->regs.sector_count & 0x7);
          break;
        }
      dev->regs.status = ATA_SR_DSC | ATA_SR_DRDY | ATA_SR_BSY;
      break;
    default:
      dev->regs.error = ATA_ERR_ABT;
      dev->regs.status = ATA_SR_ERR | ATA_SR_BSY | ATA_SR_DRDY;
      /* FIXME */
      fprintf (stderr, "Fixme: Unknown set features sub-command %x\n",
               dev->regs.features);
    }
}
 
 
int
ata_device_execute_cmd (struct ata_device *device)
{
  /* execute the commands */
  switch (device->regs.command)
    {
    case DEVICE_RESET:
      ata_device_reset_cmd (device);
      SCHED_ADD (ata_cmd_complete, device, 4000000);
      return 0;
 
    case EXECUTE_DEVICE_DIAGNOSTICS:
      ata_execute_device_diagnostics_cmd (device);
      SCHED_ADD (ata_cmd_complete, device, 4000000);
      return 0;
 
    case IDENTIFY_DEVICE:
      ata_identify_device_cmd (device);
      /* FIXME: This should generate an interrupt, but linux is abit broken so
       * it doesn't happen */
      //SCHED_ADD(ata_cmd_complete, device, 40000);
      return 0;
 
    case INITIALIZE_DEVICE_PARAMETERS:
      ata_initialize_device_parameters_cmd (device);
      SCHED_ADD (ata_cmd_complete, device, 400000);
      return 0;
 
    case READ_SECTORS:
      ata_read_sectors_cmd (device);
      /* PIO-in command -- Doesn't interrupt on completion */
      return 0;
 
    case READ_NATIVE_MAX_ADDRESS:
      ata_read_native_max_addr (device);
      SCHED_ADD (ata_cmd_complete, device, 40000);
      return 0;
 
    case WRITE_SECTORS:
      ata_write_sectors (device);
      SCHED_ADD (ata_cmd_complete, device, 40000);
      return 0;
 
    case SET_FEATURES:
      ata_set_features (device);
      SCHED_ADD (ata_cmd_complete, device, 4000);
      return 0;
 
    default:
      device->regs.error = ATA_ERR_ABT;
      device->regs.status = ATA_SR_ERR | ATA_SR_BSY | ATA_SR_DRDY;
      /* FIXME */
      fprintf (stderr, "Fixme: Unknown command %x\n", device->regs.command);
      SCHED_ADD (ata_cmd_complete, device, 40000);
      return -1;
    }
}
Browse

Tools

Subversion Repositories openrisc_2011-10-31

[/] [openrisc/] [trunk/] [or1ksim/] [peripheral/] [atadevice-cmdi.c] - Blame information for rev 166

Line No.	Rev	Author	Line
1	19	jeremybenn	`/* atadevice_cmdi.c -- ATA Device simulation`
2			`Command interpreter for the simulated harddisk.`
3
4			`Copyright (C) 2002 Richard Herveille, rherveille@opencores.org`
5			`Copyright (C) 2008 Embecosm Limited`
6
7			`Contributor Jeremy Bennett <jeremy.bennett@embecosm.com>`
8
9			`This file is part of Or1ksim, the OpenRISC 1000 Architectural Simulator.`
10
11			`This program is free software; you can redistribute it and/or modify it`
12			`under the terms of the GNU General Public License as published by the Free`
13			`Software Foundation; either version 3 of the License, or (at your option)`
14			`any later version.`
15
16			`This program is distributed in the hope that it will be useful, but WITHOUT`
17			`ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or`
18			`FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for`
19			`more details.`
20
21			`You should have received a copy of the GNU General Public License along`
22			`with this program. If not, see <http://www.gnu.org/licenses/>. */`
23
24			`/* This program is commented throughout in a fashion suitable for processing`
25			`with Doxygen. */`
26
27			`/* For fun, count the number of FIXMEs :-( */`
28
29
30			`/* Autoconf and/or portability configuration */`
31			`#include "config.h"`
32
33			`/* Package includes */`
34			`#include "atadevice-cmdi.h"`
35			`#include "atahost.h"`
36			`#include "atacmd.h"`
37			`#include "sched.h"`
38
39
40			`/* FIXME: If device0 is not selected and then an interrupt occurs and`