URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [orpsocv2/] [bench/] [verilog/] [usbhostslave/] [usbSlaveControl_h.v] - Blame information for rev 811

Go to most recent revision | Details | Compare with Previous | View Log


//////////////////////////////////////////////////////////////////////
// usbSlaveControl.v                                           
//////////////////////////////////////////////////////////////////////
 
`ifdef usbSlaveControl_h_vdefined
`else
`define usbSlaveControl_h_vdefined
 
//endPointConstants 
`define NUM_OF_ENDPOINTS 4
`define NUM_OF_REGISTERS_PER_ENDPOINT 4
`define BASE_INDEX_FOR_ENDPOINT_REGS 0
`define ENDPOINT_CONTROL_REG 0
`define ENDPOINT_STATUS_REG 1
`define ENDPOINT_TRANSTYPE_STATUS_REG 2
`define NAK_TRANSTYPE_STATUS_REG 3
`define EP0_CTRL_REG 5'h0
`define EP0_STS_REG 5'h1
`define EP0_TRAN_TYPE_STS_REG 5'h2
`define EP0_NAK_TRAN_TYPE_STS_REG 5'h3
`define EP1_CTRL_REG 5'h4
`define EP1_STS_REG 5'h5
`define EP1_TRAN_TYPE_STS_REG 5'h6
`define EP1_NAK_TRAN_TYPE_STS_REG 5'h7
`define EP2_CTRL_REG 5'h8
`define EP2_STS_REG 5'h9
`define EP2_TRAN_TYPE_STS_REG 5'ha
`define EP2_NAK_TRAN_TYPE_STS_REG 5'hb
`define EP3_CTRL_REG 5'hc
`define EP3_STS_REG 5'hd
`define EP3_TRAN_TYPE_STS_REG 5'he
`define EP3_NAK_TRAN_TYPE_STS_REG 5'hf
 
 
//SCRegIndices 
`define LAST_ENDP_REG = `BASE_INDEX_FOR_ENDPOINT_REGS + (`NUM_OF_REGISTERS_PER_ENDPOINT * `NUM_OF_ENDPOINTS) - 1
`define SC_CONTROL_REG 5'h10
`define SC_LINE_STATUS_REG 5'h11
`define SC_INTERRUPT_STATUS_REG 5'h12
`define SC_INTERRUPT_MASK_REG 5'h13
`define SC_ADDRESS 5'h14
`define SC_FRAME_NUM_MSP 5'h15
`define SC_FRAME_NUM_LSP 5'h16
`define SCREG_BUFFER_LEN 5'h17
//SCRXStatusRegIndices 
`define NAK_SET_MASK 8'h10
`define SC_CRC_ERROR_BIT 0
`define SC_BIT_STUFF_ERROR_BIT 1
`define SC_RX_OVERFLOW_BIT 2
`define SC_RX_TIME_OUT_BIT 3
`define SC_NAK_SENT_BIT 4
`define SC_STALL_SENT_BIT 5
`define SC_ACK_RXED_BIT 6
`define SC_DATA_SEQUENCE_BIT 7
//SCEndPointControlRegIndices 
`define ENDPOINT_ENABLE_BIT 0
`define ENDPOINT_READY_BIT 1
`define ENDPOINT_OUTDATA_SEQUENCE_BIT 2
`define ENDPOINT_SEND_STALL_BIT 3
`define ENDPOINT_ISO_ENABLE_BIT 4
//SCMasterControlegIndices 
`define SC_GLOBAL_ENABLE_BIT 0
`define SC_TX_LINE_STATE_LSBIT 1
`define SC_TX_LINE_STATE_MSBIT 2
`define SC_DIRECT_CONTROL_BIT 3
`define SC_FULL_SPEED_LINE_POLARITY_BIT 4
`define SC_FULL_SPEED_LINE_RATE_BIT 5
`define SC_CONNECT_TO_HOST_BIT 6
//SCinterruptRegIndices 
`define TRANS_DONE_BIT 0
`define RESUME_INT_BIT 1
`define RESET_EVENT_BIT 2  //Line has entered reset state or left reset state
`define SOF_RECEIVED_BIT 3
`define NAK_SENT_INT_BIT 4
`define VBUS_DET_INT_BIT 5
//TXTransactionTypes 
`define SC_SETUP_TRANS 0
`define SC_IN_TRANS 1
`define SC_OUTDATA_TRANS 2
//timeOuts 
`define SC_RX_PACKET_TOUT 18
 
//line status reg
`define VBUS_PRES_BIT 2
 
`endif //usbSlaveControl_h_vdefined  

Line No.	Rev	Author	Line
1	408	julius	`//////////////////////////////////////////////////////////////////////`
2			`// usbSlaveControl.v`
3			`//////////////////////////////////////////////////////////////////////`
4
5			`ifdef usbSlaveControl_h_vdefined
6			`else
7			`define usbSlaveControl_h_vdefined
8
9			`//endPointConstants`
10			`define NUM_OF_ENDPOINTS 4
11			`define NUM_OF_REGISTERS_PER_ENDPOINT 4
12			`define BASE_INDEX_FOR_ENDPOINT_REGS 0
13			`define ENDPOINT_CONTROL_REG 0
14			`define ENDPOINT_STATUS_REG 1
15			`define ENDPOINT_TRANSTYPE_STATUS_REG 2
16			`define NAK_TRANSTYPE_STATUS_REG 3
17			`define EP0_CTRL_REG 5'h0
18			`define EP0_STS_REG 5'h1
19			`define EP0_TRAN_TYPE_STS_REG 5'h2
20			`define EP0_NAK_TRAN_TYPE_STS_REG 5'h3
21			`define EP1_CTRL_REG 5'h4
22			`define EP1_STS_REG 5'h5
23			`define EP1_TRAN_TYPE_STS_REG 5'h6
24			`define EP1_NAK_TRAN_TYPE_STS_REG 5'h7
25			`define EP2_CTRL_REG 5'h8
26			`define EP2_STS_REG 5'h9
27			`define EP2_TRAN_TYPE_STS_REG 5'ha
28			`define EP2_NAK_TRAN_TYPE_STS_REG 5'hb
29			`define EP3_CTRL_REG 5'hc
30			`define EP3_STS_REG 5'hd
31			`define EP3_TRAN_TYPE_STS_REG 5'he
32			`define EP3_NAK_TRAN_TYPE_STS_REG 5'hf
33
34
35			`//SCRegIndices`
36			`define LAST_ENDP_REG = `BASE_INDEX_FOR_ENDPOINT_REGS + (`NUM_OF_REGISTERS_PER_ENDPOINT * `NUM_OF_ENDPOINTS) - 1
37			`define SC_CONTROL_REG 5'h10
38			`define SC_LINE_STATUS_REG 5'h11
39			`define SC_INTERRUPT_STATUS_REG 5'h12
40			`define SC_INTERRUPT_MASK_REG 5'h13
41			`define SC_ADDRESS 5'h14
42			`define SC_FRAME_NUM_MSP 5'h15
43			`define SC_FRAME_NUM_LSP 5'h16
44			`define SCREG_BUFFER_LEN 5'h17
45			`//SCRXStatusRegIndices`
46			`define NAK_SET_MASK 8'h10
47			`define SC_CRC_ERROR_BIT 0
48			`define SC_BIT_STUFF_ERROR_BIT 1
49			`define SC_RX_OVERFLOW_BIT 2
50			`define SC_RX_TIME_OUT_BIT 3
51			`define SC_NAK_SENT_BIT 4
52			`define SC_STALL_SENT_BIT 5
53			`define SC_ACK_RXED_BIT 6
54			`define SC_DATA_SEQUENCE_BIT 7
55			`//SCEndPointControlRegIndices`
56			`define ENDPOINT_ENABLE_BIT 0
57			`define ENDPOINT_READY_BIT 1
58			`define ENDPOINT_OUTDATA_SEQUENCE_BIT 2
59			`define ENDPOINT_SEND_STALL_BIT 3
60			`define ENDPOINT_ISO_ENABLE_BIT 4
61			`//SCMasterControlegIndices`
62			`define SC_GLOBAL_ENABLE_BIT 0
63			`define SC_TX_LINE_STATE_LSBIT 1
64			`define SC_TX_LINE_STATE_MSBIT 2
65			`define SC_DIRECT_CONTROL_BIT 3
66			`define SC_FULL_SPEED_LINE_POLARITY_BIT 4
67			`define SC_FULL_SPEED_LINE_RATE_BIT 5
68			`define SC_CONNECT_TO_HOST_BIT 6
69			`//SCinterruptRegIndices`
70			`define TRANS_DONE_BIT 0
71			`define RESUME_INT_BIT 1
72			`define RESET_EVENT_BIT 2 //Line has entered reset state or left reset state
73			`define SOF_RECEIVED_BIT 3
74			`define NAK_SENT_INT_BIT 4
75			`define VBUS_DET_INT_BIT 5
76			`//TXTransactionTypes`
77			`define SC_SETUP_TRANS 0
78			`define SC_IN_TRANS 1
79			`define SC_OUTDATA_TRANS 2
80			`//timeOuts`
81			`define SC_RX_PACKET_TOUT 18
82
83			`//line status reg`
84			`define VBUS_PRES_BIT 2
85
86			`endif //usbSlaveControl_h_vdefined

Browse

Tools

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [orpsocv2/] [bench/] [verilog/] [usbhostslave/] [usbSlaveControl_h.v] - Blame information for rev 811