URL https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [orpsocv2/] [bench/] [verilog/] [usbhostslave/] [usb_hostslave_tb.v] - Blame information for rev 541

Go to most recent revision | Details | Compare with Previous | View Log

// USB stimulus
 
// Adam Edvardsson, adam.edvardsson@orsoc.se
// Julius Baxter, julius.baxter@orsoc.se
// Adapted from testbench for usbhostslave project on Opencores by 
// Steve Fielding: http://opencores.org/project,usbhostslave
 
// To enable USB host tests, enable core USB0 or USB1 in host-only mode.
 
// To enable USB slave tests, enable USB1 in slave only mode
 
wire usbClk;
 
// We'll hook up the host to these wires
wire [1:0] usbhostwiredataout;
wire [1:0] usbhostwiredatain;
wire usbhostwirectrlout;
wire usbhostfullspeed;
 
// We'll hook up the host to these wires
wire [1:0] usbslavewiredataout;
wire [1:0] usbslavewiredatain;
wire usbslavewirectrlout;
wire usbslavefullspeed;
 
// Depending on which USB core is enabled, and if it's got slave compatibility, 
// we assign the host wires
`ifdef USB0
// USB0 can either be host, or hostslave, either way it's got host capability
// if it's defined
assign usbhostwiredataout = usb0dat_pad_o;
assign usbhostwirectrlout = usb0ctrl_pad_o;
assign usbhostfullspeed = usb0fullspeed_pad_o;
assign usb0dat_pad_i = usbhostwiredatain;
 
 `define USB_HOST_TESTS_ENABLE
 
`endif //  `ifdef USB0
 
 
// check if USB1 should be used as a HOST if USB0 isn't enable
`ifndef USB_HOST_TESTS_ENABLE
 `ifdef USB1
  `ifndef USB1_ONLY_SLAVE
// ... and that it's in slave-only configuration
// then we can use USB1 host instead
assign usbhostwiredataout = usb1dat_pad_o;
assign usbhostwirectrlout = usb1ctrl_pad_o;
assign usbhostfullspeed = usb1fullspeed_pad_o;
assign usb1dat_pad_i = usbhostwiredatain;
 
   `define USB_HOST_TESTS_ENABLE
 
  `endif //  `ifndef USB1_ONLY_SLAVE
 `endif //  `ifdef USB1
`endif //  `ifndef USB_HOST_TESTS_ENABLE
 
`ifdef USB1
 `ifdef USB1_ONLY_SLAVE
 
// USB1 is slave only, so we can do the slave tests
assign usbslavewiredataout = usb1dat_pad_o;
assign usbslavewirectrlout = usb1ctrl_pad_o;
assign usbslavefullspeed = usb1fullspeed_pad_o;
assign usb1dat_pad_i = usbslavewiredatain;
 
  `define USB_SLAVE_TESTS_ENABLE
 
 `endif //  `ifdef USB1_ONLY_SLAVE
`endif //  `ifdef USB1
 
 
`define SIM_SLAVE_BASE_ADDR 9'h100
`define CLK_48MHZ_HALF_PERIOD 10.4167
 
 
 
wire DPlusPullup;
wire DPlusPullDown;
wire DMinusPullup;
wire DMinusPullDown;
 
pullup(DPlusPullup);
pulldown(DPlusPullDown);
pullup(DMinusPullup);
pulldown(DMinusPullDown);
 
// USB clock generation
reg                                  usb_clk_generated = 0;
always
  begin
     #(`CLK_48MHZ_HALF_PERIOD) usb_clk_generated <=  !rst_n ? 0 : ~usb_clk_generated;
  end
 
   assign usbClk = usb_clk_generated;
 
 
 
   // Did we detect a USB host in the design?
`ifdef USB_HOST_TESTS_ENABLE
 
   wire [8:0]                         usbslave_wbmaster_adr;
   wire [7:0]                         usbslave_wbmaster_din;
   wire [7:0]                         usbslave_wbmaster_dout;
   wire                              usbslave_wbmaster_stb;
   wire                              usbslave_wbmaster_we;
   wire                              usbslave_wbmaster_ack;
 
 
   wire                              usbhostwirectrlout_oe;
   wire [1:0]                         usbtbslaveWireDataIn;
   wire [1:0]                         usbtbslaveWireDataOut;
   wire                              usbtbslaveDPlusPullup;
   wire                              usbtbslaveDMinusPullup;
   wire                              usbtbslaveWireCtrlOut;
 
   reg                               USBSlaveWireVP;
   reg                               USBSlaveWireVM;
 
 
   assign usbhostwirectrlout_oe = ~usbhostwirectrlout;
 
   assign usbhostwiredatain = {USBSlaveWireVP, USBSlaveWireVM};
   assign usbtbslaveWireDataIn = {USBSlaveWireVP, USBSlaveWireVM};
 
   always @(*) begin
      if (usbhostwirectrlout_oe == 1'b1 && usbtbslaveWireCtrlOut == 1'b0)
        {USBSlaveWireVP, USBSlaveWireVM} <= usbhostwiredataout;
      else if (usbhostwirectrlout_oe == 1'b0 && usbtbslaveWireCtrlOut == 1'b1)
        {USBSlaveWireVP, USBSlaveWireVM} <= usbtbslaveWireDataOut;
      else if (usbhostwirectrlout_oe == 1'b1 && usbtbslaveWireCtrlOut == 1'b1)
        {USBSlaveWireVP, USBSlaveWireVM} <= 2'bxx;
      else if (usbhostwirectrlout_oe == 1'b0 && usbtbslaveWireCtrlOut == 1'b0)
        begin
           if (usbtbslaveDPlusPullup == 1'b1)
             USBSlaveWireVP <= DPlusPullup;
           else
             USBSlaveWireVP <= DPlusPullDown;
           if (usbtbslaveDMinusPullup == 1'b1)
             USBSlaveWireVM <= DMinusPullup;
           else
             USBSlaveWireVM <= DMinusPullDown;
        end
   end
 
 
   //Parameters declaration: 
   defparam u_slave.EP0_FIFO_DEPTH = 64;
   parameter EP0_FIFO_DEPTH = 64;
   defparam u_slave.EP0_FIFO_ADDR_WIDTH = 6;
   parameter EP0_FIFO_ADDR_WIDTH = 6;
   defparam u_slave.EP1_FIFO_DEPTH = 64;
   parameter EP1_FIFO_DEPTH = 64;
   defparam u_slave.EP1_FIFO_ADDR_WIDTH = 6;
   parameter EP1_FIFO_ADDR_WIDTH = 6;
   defparam u_slave.EP2_FIFO_DEPTH = 64;
   parameter EP2_FIFO_DEPTH = 64;
   defparam u_slave.EP2_FIFO_ADDR_WIDTH = 6;
   parameter EP2_FIFO_ADDR_WIDTH = 6;
   defparam u_slave.EP3_FIFO_DEPTH = 64;
   parameter EP3_FIFO_DEPTH = 64;
   defparam u_slave.EP3_FIFO_ADDR_WIDTH = 6;
   parameter EP3_FIFO_ADDR_WIDTH = 6;
 
   wire                              usb_tbslavesofrxed_irq;
   wire                              usb_tbslaveresetevent_irq;
   wire                              usb_tbslaveresume_irq;
   wire                              usb_tbslavetransdone_irq;
   wire                              usb_tbslavenaksent_irq;
   wire                              usb_tbslavevbusdet_irq;
 
   wire                              usb_tboe, usb_tboe_n;
 
 
   // USB slave instantiation
   usbslave_simlib u_slave
     (
      // USB PHY lines
      // In
      .clk_i        (clk), // Board clock
      .rst_i        (!rst_n),
      .address_i    (usbslave_wbmaster_adr[7:0]),
      .data_i       (usbslave_wbmaster_dout),
      .data_o       (usbslave_wbmaster_din),
      .we_i         (usbslave_wbmaster_we),
      .strobe_i     (usbslave_wbmaster_stb),
      .ack_o        (usbslave_wbmaster_ack),
 
      .usbClk        (usbClk), // logic clock,48MHz +/-0.25%
 
 
      // Interrupt lines
 
      .slaveSOFRxedIntOut               (usb_tbslavesofrxed_irq),
      .slaveResetEventIntOut            (usb_tbslaveresetevent_irq),
      .slaveResumeIntOut                (usb_tbslaveresume_irq),
      .slaveTransDoneIntOut             (usb_tbslavetransdone_irq),
      .slaveNAKSentIntOut               (usb_tbslavenaksent_irq),
      .slaveVBusDetIntOut               (usb_tbslavevbusdet_irq),
 
      .USBWireDataIn(usbtbslaveWireDataIn),
      .USBWireDataInTick(),
      .USBWireDataOut(usbtbslaveWireDataOut),
      .USBWireDataOutTick(),
      .USBWireCtrlOut(usbtbslaveWireCtrlOut),
      .USBFullSpeed(),
      .USBDPlusPullup(usbtbslaveDPlusPullup),
      .USBDMinusPullup(usbtbslaveDMinusPullup),
      .vBusDetect(1'b1)
 
 
      );
 
   // Wishbone bus master, for controlling USB slave
   wb_master_model
     #(
       .dwidth(8),
       .awidth(9)
       )
   usbslave_wbm
     (
      .clk(clk),
 
      .rst(!rst_n),
      .adr(usbslave_wbmaster_adr),
      .din(usbslave_wbmaster_din),
      .dout(usbslave_wbmaster_dout),
      .cyc(),
      .stb(usbslave_wbmaster_stb),
      .we(usbslave_wbmaster_we),
      .sel(),
      .ack(usbslave_wbmaster_ack),
      .err(1'b0),
      .rty(1'b0)
      );
 
 
 
   reg [7:0]                          hostTestData;
   reg [15:0]                         hostTestDataWord;
   reg [7:0]                          hostTestDataRead;
   reg [7:0]                          hostTestDataWrite;
   reg [7:0]                          hostTestUSBAddress;
   integer                           hostTestDataSize;
   integer                           hostTestDataItr;
   // Don't have vbus detect in this system...
   //assign    usbhostvbusdetect = 1'b1;
 
 
 
   // Perform transactions and tests through a USB slave to the USB host in the
   // the DUT
 
   initial
     begin
 
        wait (usbhostfullspeed);
        $write("USB host tb: USB Host test starts at:%t\n",$time);
 
        usbslave_wbm.wb_read(1,
                             `SIM_SLAVE_BASE_ADDR +
                             `HOST_SLAVE_CONTROL_BASE +
                             `HOST_SLAVE_VERSION_REG , hostTestDataRead);
        $write("USB host tb: Slave Version number = 0x%0x\n", hostTestDataRead);
 
 
        $write("USB host tb: Configure host and slave mode\n");
        usbslave_wbm.wb_write(1,8'he0,8'h0);
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_CONTROL_REG , 8'h70);
        #30000;
        //expecting connection event interrupt
        //expecting change in reset state event, and change in vbus state event
        usbslave_wbm.wb_cmp(1,
                            `SIM_SLAVE_BASE_ADDR +
                            `SCREG_BASE +
                            `SC_INTERRUPT_STATUS_REG , 8'h24);
 
        //expecting full speed connect and vbus present
        usbslave_wbm.wb_cmp(1,
                            `SIM_SLAVE_BASE_ADDR +
                            `SCREG_BASE +
                            `SC_LINE_STATUS_REG , 8'h06);
        $write("USB host tb: :USB slave connected and fullspeed enabled\n");
 
        hostTestUSBAddress = 8'h00;
        #200;
        $write("USB host tb: Slave ENABLE Transport tO EP1\n");
        //enable endpoint, and make ready
        usbslave_wbm.wb_write(1, `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_CONTROL_REG , 8'h71);
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_ADDRESS , 8'h00);
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `EP0_CTRL_REG , 8'h03);
        //cancel interrupt
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_INTERRUPT_STATUS_REG , 8'hff);
 
        usbslave_wbm.wb_read(1,
                             `SIM_SLAVE_BASE_ADDR +
                             `SCREG_BASE +
                             `SC_INTERRUPT_STATUS_REG , hostTestData);
        while (hostTestData != 8'h01) begin
           usbslave_wbm.wb_read(1,
                                `SIM_SLAVE_BASE_ADDR +
                                `SCREG_BASE +
                                `SC_INTERRUPT_STATUS_REG , hostTestData);
        end
 
 
        usbslave_wbm.wb_cmp(1,
                            `SIM_SLAVE_BASE_ADDR +
                            `SCREG_BASE +
                            `SC_INTERRUPT_STATUS_REG , 8'h01);
        //endpoint enabled, and endpoint ready cleared
        usbslave_wbm.wb_cmp(1,
                            `SIM_SLAVE_BASE_ADDR +
                            `SCREG_BASE +
                            `EP0_CTRL_REG , 8'h01);
        $write("USB host tb: Checking receive hostTestData ");
        hostTestData = 8'h00;
        for (hostTestDataItr=0;
             hostTestDataItr<hostTestDataSize;
             hostTestDataItr=hostTestDataItr+1) begin
           usbslave_wbm.wb_cmp(1,
                               `SIM_SLAVE_BASE_ADDR +
                               `EP0_RX_FIFO_BASE +
                               `FIFO_DATA_REG , hostTestData);
           hostTestData = hostTestData + 1'b1;
        end
        $write("- PASSED T4\n");
 
        $write("USB host tb: Trans test: Device address = 0x5a, 64 byte OUT DATA0 transaction to Endpoint 1\n");
        hostTestUSBAddress = 8'h5a;
        hostTestDataSize = 64;
 
        //enable endpoint, and make ready
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_CONTROL_REG , 8'h71);
        usbslave_wbm.wb_write(1, `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_ADDRESS , hostTestUSBAddress);
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `EP1_CTRL_REG , 8'h03);
        //cancel interrupt
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_INTERRUPT_STATUS_REG , 8'hff);
 
        usbslave_wbm.wb_read(1,
                             `SIM_SLAVE_BASE_ADDR +
                             `SCREG_BASE +
                             `SC_INTERRUPT_STATUS_REG , hostTestData);
        while (hostTestData != 8'h01) begin
           usbslave_wbm.wb_read(1,
                                `SIM_SLAVE_BASE_ADDR +
                                `SCREG_BASE +
                                `SC_INTERRUPT_STATUS_REG , hostTestData);
        end
 
        usbslave_wbm.wb_cmp(1,
                            `SIM_SLAVE_BASE_ADDR +
                            `SCREG_BASE +
                            `SC_INTERRUPT_STATUS_REG , 8'h01);
        //endpoint enabled, and endpoint ready cleared
        usbslave_wbm.wb_cmp(1,
                            `SIM_SLAVE_BASE_ADDR +
                            `SCREG_BASE +
                            `EP0_CTRL_REG , 8'h01);
        $write("USB host tb: Checking receive hostTestData ");
        hostTestData = 8'h00;
        for (hostTestDataItr=0;
             hostTestDataItr<hostTestDataSize;
             hostTestDataItr=hostTestDataItr+1) begin
           usbslave_wbm.wb_cmp(1,
                               `SIM_SLAVE_BASE_ADDR +
                               `EP1_RX_FIFO_BASE  +
                               `FIFO_DATA_REG , hostTestData);
           hostTestData = hostTestData + 1'b1;
        end
        $write("- PASSED T5\n");
 
        #2000;
        $write("USB host tb: Trans test: Device address = 0x01, 2 byte IN transaction to Endpoint 2\n");
        hostTestUSBAddress = 8'h01;
        hostTestDataSize = 64;
        $write("USB host tb: USB Host test starts at:%t\n",$time);
        //enable endpoint, and make ready
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_CONTROL_REG , 8'h71);
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_ADDRESS , hostTestUSBAddress);
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `EP2_CTRL_REG , 8'h03);
        usbslave_wbm.wb_write(1,
                              `SIM_SLAVE_BASE_ADDR +
                              `SCREG_BASE +
                              `SC_INTERRUPT_STATUS_REG , 8'hff);
        hostTestData = 8'hC0;
        for (hostTestDataItr=64;
             hostTestDataItr>0;
             hostTestDataItr=hostTestDataItr-1) begin
           usbslave_wbm.wb_write(1,
                                 `SIM_SLAVE_BASE_ADDR +
                                 `EP2_TX_FIFO_BASE  +
                                 `FIFO_DATA_REG , hostTestData);
           hostTestData = hostTestData - 3'b011;
        end
 
        usbslave_wbm.wb_read(1,
                             `SIM_SLAVE_BASE_ADDR +
                             `SCREG_BASE +
                             `SC_INTERRUPT_STATUS_REG , hostTestData);
        while (hostTestData != 8'h01) begin
           usbslave_wbm.wb_read(1,
                                `SIM_SLAVE_BASE_ADDR +
                                `SCREG_BASE +
                                `SC_INTERRUPT_STATUS_REG , hostTestData);
        end
        #3500;
 
        $write("USB host tb: PASSED USB test\n");
        $write("USB host tb: Finished all tests\n");
 
     end
 
 
`endif //  `ifdef USB_HOST_TESTS_ENABLE
 
 
`ifdef USB_SLAVE_TESTS_ENABLE
 
 `define SIM_HOST_BASE_ADDR 9'h000
 
 
   wire [8:0] usbhost_wbmaster_adr;
   wire [7:0] usbhost_wbmaster_dout;
   wire [7:0] usbhost_wbmaster_din;
   wire       usbhost_wbmaster_we;
   wire       usbhost_wbmaster_ack;
   wire       usbhost_wbmaster_stb;
 
   wire       usb_tbhostSOFSentIntOut;
   wire       usb_tbhostConnEventIntOut;
   wire       usb_tbhostResumeIntOut;
   wire       usb_tbhostTransDoneIntOut;
 
   reg        USBHostWireVP;
   reg        USBHostWireVM;
 
   wire       hostUSBWireCtrlOut;
 
 
   wire [1:0] hostUSBWireDataIn;
   wire [1:0] hostUSBWireDataOut;
 
 
   assign hostUSBWireDataIn = {USBHostWireVP, USBHostWireVM};
   assign usbslavewiredatain = {USBHostWireVP, USBHostWireVM};
 
   always @(*) begin
      if (hostUSBWireCtrlOut == 1'b1 && !usbslavewirectrlout == 1'b0)
        {USBHostWireVP, USBHostWireVM} <= hostUSBWireDataOut;
      else if (hostUSBWireCtrlOut == 1'b0 && !usbslavewirectrlout == 1'b1)
        {USBHostWireVP, USBHostWireVM} <= usbslavewiredataout;
      else if (hostUSBWireCtrlOut == 1'b1 && !usbslavewirectrlout == 1'b1)
        {USBHostWireVP, USBHostWireVM} <= 2'bxx;
      else if (hostUSBWireCtrlOut == 1'b0 && !usbslavewirectrlout == 1'b0) begin
         // No indication of pullup/downs in our design...
         // assume VP pullup and VM pull down(!?)
         USBHostWireVP <= DPlusPullup;
         USBHostWireVM <= DMinusPullDown;
      end
   end
 
 
 
   //Parameters declaration: 
   defparam u_usbhost.HOST_FIFO_DEPTH = 64;
   parameter HOST_FIFO_DEPTH = 64;
   defparam u_usbhost.HOST_FIFO_ADDR_WIDTH = 6;
   parameter HOST_FIFO_ADDR_WIDTH = 6;
 
   usbhost_simlib u_usbhost
     (
      .clk_i(clk),
      .rst_i(!rst_n),
      .address_i(usbhost_wbmaster_adr[7:0]),
      .data_i(usbhost_wbmaster_dout),
      .data_o(usbhost_wbmaster_din),
      .we_i(usbhost_wbmaster_we),
      .strobe_i(usbhost_wbmaster_stb),
      .ack_o(usbhost_wbmaster_ack),
      .usbClk(usbClk),
 
      .hostSOFSentIntOut(usb_tbhostSOFSentIntOut),
      .hostConnEventIntOut(usb_tbhostConnEventIntOut),
      .hostResumeIntOut(usb_tbhostResumeIntOut),
      .hostTransDoneIntOut(usb_tbhostTransDoneIntOut),
      .USBWireDataIn(hostUSBWireDataIn),
      .USBWireDataInTick(),
      .USBWireDataOut(hostUSBWireDataOut),
      .USBWireDataOutTick(),
      .USBWireCtrlOut(hostUSBWireCtrlOut),
      .USBFullSpeed()
 
 
      );
   wb_master_model
     #(
       .dwidth(8),
       .awidth(9)
       )
   usbhost_wbm
     (
      .clk(clk),
      .rst(!rst_n),
      .adr(usbhost_wbmaster_adr),
      .din(usbhost_wbmaster_din),
      .dout(usbhost_wbmaster_dout),
      .cyc(),
      .stb(usbhost_wbmaster_stb),
      .we(usbhost_wbmaster_we),
      .sel(),
      .ack(usbhost_wbmaster_ack),
      .err(1'b0),
      .rty(1'b0)
      );
 
 
   reg [7:0] slaveTestData;
   reg [15:0] slaveTestDataWord;
   reg [7:0]  slaveTestDataRead;
   reg [7:0]  slaveTestDataWrite;
   reg [7:0]  slaveTestUSBAddress;
   reg [7:0]  slaveTestUSBEndPoint;
   reg [7:0]  slaveTestTransType;
   integer    slaveTestDataSize;
   integer    slaveTestDataItr;
 
   // Don't have vbusdetect in this system
   //assign    usbslavevbusdetect = 1'b1;
 
   initial
     begin
 
        wait (usbslavefullspeed);
        $write("USB Slave test starts at:%t\n",$time);
 
        #14000;
 
        usbhost_wbm.wb_read(1,
                            `SIM_HOST_BASE_ADDR +
                            `HOST_SLAVE_CONTROL_BASE +
                            `HOST_SLAVE_VERSION_REG , slaveTestDataRead);
        $display("Host Version number = 0x%0x\n", slaveTestDataRead);
 
        $write("USB slave tb: Testing host register read/write ");
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_LINE_CONTROL_REG , 8'h18);
        usbhost_wbm.wb_cmp(1,
                           `SIM_HOST_BASE_ADDR +
                           `HCREG_BASE +
                           `TX_LINE_CONTROL_REG , 8'h18);
        $write("- PASSED\n");
 
 
        $write("USB slave tb: Testing register reset ");
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HOST_SLAVE_CONTROL_BASE +
                             `HOST_SLAVE_CONTROL_REG , 8'h2);
        //usbhost_wbm.wb_write(1, `SIM_SLAVE_BASE_ADDR + `HOST_SLAVE_CONTROL_BASE+`HOST_SLAVE_CONTROL_REG , 8'h2);
        #1000;
        usbhost_wbm.wb_cmp(1,
                           `SIM_HOST_BASE_ADDR +
                           `HCREG_BASE +
                           `TX_LINE_CONTROL_REG , 8'h00);
        //usbhost_wbm.wb_cmp(1, `SIM_SLAVE_BASE_ADDR + `SCREG_BASE+`SC_CONTROL_REG , 8'h00);
        $write("- PASSED\n");
        #1000;
 
        $write("USB slave tb: Configuring host\n");
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HOST_SLAVE_CONTROL_BASE +
                             `HOST_SLAVE_CONTROL_REG , 8'h1);
        $write("USB slave tb: Connect full speed ");
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_LINE_CONTROL_REG , 8'h18);
        #20000;
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `INTERRUPT_STATUS_REG , 8'h04);
 
        $write("- PASSED\n");
        #225000;
 
        //Transfer 1
        $write("USB slave tb: Trans test 1: Device address = 0x63, 2 byte SETUP transaction to Endpoint 0\n");
        slaveTestUSBAddress = 8'h63;
        slaveTestUSBEndPoint = 8'h00;
        slaveTestTransType = `SETUP_TRANS;
        slaveTestDataSize = 2;
 
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `INTERRUPT_STATUS_REG , 8'h04);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_ADDR_REG , slaveTestUSBAddress);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_ENDP_REG , slaveTestUSBEndPoint);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_TRANS_TYPE_REG , slaveTestTransType);
        slaveTestData = 8'h00;
        for (slaveTestDataItr=0;
             slaveTestDataItr<slaveTestDataSize;
             slaveTestDataItr=slaveTestDataItr+1) begin
           usbhost_wbm.wb_write(1,
                                `SIM_HOST_BASE_ADDR +
                                `HOST_TX_FIFO_BASE  +
                                `FIFO_DATA_REG , slaveTestData);
           slaveTestData = slaveTestData + 1'b1;
        end
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_CONTROL_REG , 8'h01);
        #35000
 
 
          usbhost_wbm.wb_cmp(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `INTERRUPT_STATUS_REG , 8'h01);
        $write("USB slave tb: Transaction done correct interrupt recived\n" );
 
 
        $write("USB slave tb: Checking receive slaveTestData ");
        slaveTestData = 8'h00;
        for (slaveTestDataItr=0;
             slaveTestDataItr<slaveTestDataSize;
             slaveTestDataItr=slaveTestDataItr+1) begin
 
           slaveTestData = slaveTestData + 1'b1;
        end
        $write("- PASSED\n");
 
        //Transfer 2
        $write("USB slave tb: Trans test 2: Device address = 0x63, 20 byte OUT DATA0 transaction to Endpoint 1\n");
        slaveTestUSBAddress = 8'h63;
        slaveTestUSBEndPoint = 8'h00;
        slaveTestTransType = `OUTDATA0_TRANS;
        slaveTestDataSize = 20;
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `INTERRUPT_STATUS_REG , 8'h04);
 
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_ADDR_REG , slaveTestUSBAddress);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_ENDP_REG , slaveTestUSBEndPoint);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_TRANS_TYPE_REG , slaveTestTransType);
        slaveTestData = 8'h00;
        for (slaveTestDataItr=0;
             slaveTestDataItr<slaveTestDataSize;
             slaveTestDataItr=slaveTestDataItr+1) begin
           usbhost_wbm.wb_write(1,
                                `SIM_HOST_BASE_ADDR +
                                `HOST_TX_FIFO_BASE  +
                                `FIFO_DATA_REG , slaveTestData);
           slaveTestData = slaveTestData + 1'b1;
        end
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_CONTROL_REG , 8'h01);
        #20000
 
          $write("USB slave tb: Checking received Transaction done interupt\n");
        usbhost_wbm.wb_cmp(1,
                           `SIM_HOST_BASE_ADDR +
                           `HCREG_BASE +
                           `INTERRUPT_STATUS_REG , 8'h01);
 
        $write("USB slave tb: Checking receive slaveTestData ");
        slaveTestData = 8'h00;
        for (slaveTestDataItr=0;
             slaveTestDataItr<slaveTestDataSize;
             slaveTestDataItr=slaveTestDataItr+1) begin
           //usbhost_wbm.wb_cmp(1, `SIM_SLAVE_BASE_ADDR + `EP1_RX_FIFO_BASE + `FIFO_DATA_REG , data);
           slaveTestData = slaveTestData + 1'b1;
        end
        $write("- PASSED\n");
        #200000
 
          //Transfer 3
          $write("USB slave tb: Trans test 3: Device address = 0x63, 20 byte OUT DATA0 transaction to Endpoint 1\n");
        slaveTestUSBAddress = 8'h63;
        slaveTestUSBEndPoint = 8'h00;
        slaveTestTransType = `OUTDATA0_TRANS;
        slaveTestDataSize = 2;
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `INTERRUPT_STATUS_REG , 8'h04);
        //enable endpoint, and make ready
 
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_ADDR_REG , slaveTestUSBAddress);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_ENDP_REG , slaveTestUSBEndPoint);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_TRANS_TYPE_REG , slaveTestTransType);
        slaveTestData = 8'h00;
        for (slaveTestDataItr=0;
             slaveTestDataItr<slaveTestDataSize;
             slaveTestDataItr=slaveTestDataItr+1) begin
           usbhost_wbm.wb_write(1,
                                `SIM_HOST_BASE_ADDR +
                                `HOST_TX_FIFO_BASE  +
                                `FIFO_DATA_REG , slaveTestData);
           slaveTestData = slaveTestData + 1'b1;
        end
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_CONTROL_REG , 8'h01);
        #20000
 
          $write("USB slave tb: Checking received Transaction done interupt ");
        usbhost_wbm.wb_cmp(1,
                           `SIM_HOST_BASE_ADDR +
                           `HCREG_BASE +
                           `INTERRUPT_STATUS_REG , 8'h01);
 
 
        slaveTestData = 8'h00;
        for (slaveTestDataItr=0;
             slaveTestDataItr<slaveTestDataSize;
             slaveTestDataItr=slaveTestDataItr+1) begin
           //usbhost_wbm.wb_cmp(1, `SIM_SLAVE_BASE_ADDR + `EP1_RX_FIFO_BASE + `FIFO_DATA_REG , slaveTestData);
           slaveTestData = slaveTestData + 1'b1;
        end
        $write("- PASSED\n");
        #200000
 
          //Transfer 4 
          $write("USB slave tb: Trans test 4: Device address = 0x63, 2 byte IN transaction to Endpoint 2\n");
        slaveTestUSBAddress = 8'h63;
        slaveTestUSBEndPoint = 8'h02;
        slaveTestTransType = `IN_TRANS;
        slaveTestDataSize = 20;
        //enable endpoint, and make ready
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `INTERRUPT_STATUS_REG , 8'h3f);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_ADDR_REG , slaveTestUSBAddress);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_ENDP_REG , slaveTestUSBEndPoint);
        usbhost_wbm.wb_write(1,
                             `SIM_HOST_BASE_ADDR +
                             `HCREG_BASE +
                             `TX_TRANS_TYPE_REG , slaveTestTransType);
        slaveTestData = 8'h00;
        for (slaveTestDataItr=0;
             slaveTestDataItr<slaveTestDataSize;
             slaveTestDataItr=slaveTestDataItr+1) begin
           //usbhost_wbm.wb_write(1, `SIM_SLAVE_BASE_ADDR + `EP2_TX_FIFO_BASE + `FIFO_DATA_REG , slaveTestData);
           slaveTestData = slaveTestData + 1'b1;
        end
        #20000
          usbhost_wbm.wb_write(1,
                               `SIM_HOST_BASE_ADDR +
                               `HCREG_BASE +
                               `TX_CONTROL_REG , 8'h01);
        #200000
          //expecting transaction done interrupt
          $write("USB slave tb: USB Slave transaction done interrupt at:%t\n",$time);
        usbhost_wbm.wb_cmp(1,
                           `SIM_HOST_BASE_ADDR +
                           `HCREG_BASE +
                           `INTERRUPT_STATUS_REG , 8'h01);
 
 
        $write("USB slave tb: Checking receive slaveTestData  ");
        slaveTestData = 8'h0;
        for (slaveTestDataItr=0;
             slaveTestDataItr<slaveTestDataSize;
             slaveTestDataItr=slaveTestDataItr+1) begin
           usbhost_wbm.wb_cmp(1,
                              `SIM_HOST_BASE_ADDR +
                              `HOST_RX_FIFO_BASE  +
                              `FIFO_DATA_REG ,slaveTestData);
           slaveTestData = slaveTestData + 1'b1;
        end
        $write("-PASSED\n");
 
        $write("Finished all tests\n");
 
     end
 
 
 
 
 
`endif
 
 
 
Browse

Tools

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [orpsocv2/] [bench/] [verilog/] [usbhostslave/] [usb_hostslave_tb.v] - Blame information for rev 541

Line No.	Rev	Author	Line
1	408	julius	`// USB stimulus`
2
3			`// Adam Edvardsson, adam.edvardsson@orsoc.se`
4			`// Julius Baxter, julius.baxter@orsoc.se`
5			`// Adapted from testbench for usbhostslave project on Opencores by`
6			`// Steve Fielding: http://opencores.org/project,usbhostslave`
7
8			`// To enable USB host tests, enable core USB0 or USB1 in host-only mode.`
9
10			`// To enable USB slave tests, enable USB1 in slave only mode`
11
12			`wire usbClk;`
13
14			`// We'll hook up the host to these wires`
15			`wire [1:0] usbhostwiredataout;`
16			`wire [1:0] usbhostwiredatain;`
17			`wire usbhostwirectrlout;`
18			`wire usbhostfullspeed;`
19
20			`// We'll hook up the host to these wires`
21			`wire [1:0] usbslavewiredataout;`
22			`wire [1:0] usbslavewiredatain;`
23			`wire usbslavewirectrlout;`
24			`wire usbslavefullspeed;`
25
26			`// Depending on which USB core is enabled, and if it's got slave compatibility,`
27			`// we assign the host wires`
28			`ifdef USB0
29			`// USB0 can either be host, or hostslave, either way it's got host capability`
30			`// if it's defined`
31			`assign usbhostwiredataout = usb0dat_pad_o;`
32			`assign usbhostwirectrlout = usb0ctrl_pad_o;`
33			`assign usbhostfullspeed = usb0fullspeed_pad_o;`
34			`assign usb0dat_pad_i = usbhostwiredatain;`
35
36			`define USB_HOST_TESTS_ENABLE
37
38			`endif // `ifdef USB0
39
40