Subversion Repositories openrisc

/* Simple SPI slave code from http://www.fpga4fun.com/SPI2.html */

/* Reading the module increments a counter. */

/* LSbit of written data shows on the LED port */

module spi_slave(clk, SCK, MOSI, MISO, SSEL, LED);

   input clk;

   input SCK, SSEL, MOSI;

   output MISO;

   output LED;

   // sync SCK to the FPGA clock using a 3-bits shift register

   reg [2:0] SCKr = 0;  always @(posedge clk) SCKr <= {SCKr[1:0], SCK};

   // now we can detect SCK rising edges

   wire      SCK_risingedge = (SCKr[2:1]==2'b01);

   // and falling edges 

   wire      SCK_fallingedge = (SCKr[2:1]==2'b10);

   // same thing for SSEL

   reg [2:0] SSELr = 3'b111;  always @(posedge clk) SSELr <= {SSELr[1:0], SSEL};

   wire      SSEL_active = ~SSELr[1];  // SSEL is active low

   // message starts at falling edge

   wire      SSEL_startmessage = (SSELr[2:1]==2'b10);

   // message stops at rising edge

   wire      SSEL_endmessage = (SSELr[2:1]==2'b01);

   // and for MOSI

   reg [1:0] MOSIr = 0;

   always @(posedge clk)

     MOSIr <= {MOSIr[0], MOSI};

   wire      MOSI_data = MOSIr[1];

   // we handle SPI in 8-bits format, so we need a 3 bits counter to

   //  count the bits as they come in

   reg [2:0] bitcnt = 0;

   reg       byte_received= 0;  // high when a byte has been received

   reg [7:0] byte_data_received = 0;

   always @(posedge clk)

     begin

        if(~SSEL_active)

          bitcnt <= 3'b000;

        else

          if(SCK_risingedge)

            begin

               bitcnt <= bitcnt + 3'b001;

               // implement a shift-left register (since we receive the data 

               // MSB first)

               byte_data_received <= {byte_data_received[6:0], MOSI_data};

            end

     end

   always @(posedge clk)

     byte_received <= SSEL_active && SCK_risingedge && (bitcnt==3'b111);

   // we use the LSB of the data received to control an LED

   reg LED = 0;

   always @(posedge clk) if(byte_received) LED <= byte_data_received[0];

   reg [7:0] byte_data_sent = 0;

   reg [7:0] cnt = 0;

   always @(posedge clk)

     if(SSEL_startmessage) cnt<=cnt+8'h1;  // count the messages

   always @(posedge clk)

     if(SSEL_active)

       begin

          if(SSEL_startmessage)

            // first byte sent in a message is the message count

            byte_data_sent <= cnt;

          else

            if(SCK_fallingedge)

              begin

                 if(bitcnt==3'b000)

                   byte_data_sent <= 8'h00;  // after that, we send 0s

                 else

                   byte_data_sent <= {byte_data_sent[6:0], 1'b0};

              end

       end

   assign MISO = (!SSEL) ? byte_data_sent[7] : 1'bZ;  // send MSB first

   // we assume that there is only one slave on the SPI bus

   // so we don't bother with a tri-state buffer for MISO

   // otherwise we would need to tri-state MISO when SSEL is inactive

endmodule