Subversion Repositories openrisc

module ram_wb_b3(

                 wb_adr_i, wb_bte_i, wb_cti_i, wb_cyc_i, wb_dat_i, wb_sel_i,

                 wb_stb_i, wb_we_i,

                 wb_ack_o, wb_err_o, wb_rty_o, wb_dat_o,

                 wb_clk_i, wb_rst_i);

   parameter dw = 32;

   parameter aw = 32;

   input [aw-1:0]        wb_adr_i;

   input [1:0]           wb_bte_i;

   input [2:0]           wb_cti_i;

   input                wb_cyc_i;

   input [dw-1:0]        wb_dat_i;

   input [3:0]           wb_sel_i;

   input                wb_stb_i;

   input                wb_we_i;

   output               wb_ack_o;

   output               wb_err_o;

   output               wb_rty_o;

   output [dw-1:0]       wb_dat_o;

   input                wb_clk_i;

   input                wb_rst_i;

   // Memory parameters

   parameter mem_size_bytes = 32'h0000_5000; // 20KBytes

   parameter mem_adr_width = 15; //(log2(mem_size_bytes));

   parameter bytes_per_dw = (dw/8);

   parameter adr_width_for_num_word_bytes = 2; //(log2(bytes_per_dw))

   parameter mem_words = (mem_size_bytes/bytes_per_dw);

   // synthesis attribute ram_style of mem is block

   reg [dw-1:0]  mem [ 0 : mem_words-1 ]   /* verilator public */ /* synthesis ram_style = no_rw_check */;

   // Register to address internal memory array

   reg [(mem_adr_width-adr_width_for_num_word_bytes)-1:0] adr;

   wire [31:0]                      wr_data;

   // Register to indicate if the cycle is a Wishbone B3-registered feedback 

   // type access

   reg                             wb_b3_trans;

   wire                            wb_b3_trans_start, wb_b3_trans_stop;

   // Register to use for counting the addresses when doing burst accesses

   reg [mem_adr_width-adr_width_for_num_word_bytes-1:0]  burst_adr_counter;

   reg [2:0]                        wb_cti_i_r;

   reg [1:0]                        wb_bte_i_r;

   wire                            using_burst_adr;

   wire                            burst_access_wrong_wb_adr;

   // Wire to indicate addressing error

   wire                            addr_err;

   // Logic to detect if there's a burst access going on

   assign wb_b3_trans_start = ((wb_cti_i == 3'b001)|(wb_cti_i == 3'b010)) &

                              wb_stb_i & !wb_b3_trans;

   assign  wb_b3_trans_stop = ((wb_cti_i == 3'b111) &

                              wb_stb_i & wb_b3_trans & wb_ack_o) | wb_err_o;

   always @(posedge wb_clk_i)

     if (wb_rst_i)

       wb_b3_trans <= 0;

     else if (wb_b3_trans_start)

       wb_b3_trans <= 1;

     else if (wb_b3_trans_stop)

       wb_b3_trans <= 0;

   // Burst address generation logic

   always @(/*AUTOSENSE*/wb_ack_o or wb_b3_trans or wb_b3_trans_start

            or wb_bte_i_r or wb_cti_i_r or wb_adr_i or adr)

     if (wb_b3_trans_start)

       // Kick off burst_adr_counter, this assumes 4-byte words when getting

       // address off incoming Wishbone bus address! 

       // So if dw is no longer 4 bytes, change this!

       burst_adr_counter = wb_adr_i[mem_adr_width-1:2];

     else if ((wb_cti_i_r == 3'b010) & wb_ack_o & wb_b3_trans)

       // Incrementing burst

       begin

          if (wb_bte_i_r == 2'b00) // Linear burst

            burst_adr_counter = adr + 1;

          if (wb_bte_i_r == 2'b01) // 4-beat wrap burst

            burst_adr_counter[1:0] = adr[1:0] + 1;

          if (wb_bte_i_r == 2'b10) // 8-beat wrap burst

            burst_adr_counter[2:0] = adr[2:0] + 1;

          if (wb_bte_i_r == 2'b11) // 16-beat wrap burst

            burst_adr_counter[3:0] = adr[3:0] + 1;

       end // if ((wb_cti_i_r == 3'b010) & wb_ack_o_r)

   always @(posedge wb_clk_i)

     wb_bte_i_r <= wb_bte_i;

   // Register it locally

   always @(posedge wb_clk_i)

     wb_cti_i_r <= wb_cti_i;

   assign using_burst_adr = wb_b3_trans;

   assign burst_access_wrong_wb_adr = (using_burst_adr &

                                       (adr != wb_adr_i[mem_adr_width-1:2]));

   // Address registering logic

   always@(posedge wb_clk_i)

     if(wb_rst_i)

       adr <= 0;

     else if (using_burst_adr)

       adr <= burst_adr_counter;

     else if (wb_cyc_i & wb_stb_i)

       adr <= wb_adr_i[mem_adr_width-1:2];

   /* Memory initialisation.

    If not Verilator model, always do load, otherwise only load when called

    from SystemC testbench.

    */

   parameter memory_file = "sram.vmem";

`ifdef verilator

   task do_readmemh;

      // verilator public

      $readmemh(memory_file, mem);

   endtask // do_readmemh

`else

   initial

     begin

        $readmemh(memory_file, mem);

     end

`endif // !`ifdef verilator

   assign wb_rty_o = 0;

   // mux for data to ram, RMW on part sel != 4'hf

   assign wr_data[31:24] = wb_sel_i[3] ? wb_dat_i[31:24] : wb_dat_o[31:24];

   assign wr_data[23:16] = wb_sel_i[2] ? wb_dat_i[23:16] : wb_dat_o[23:16];

   assign wr_data[15: 8] = wb_sel_i[1] ? wb_dat_i[15: 8] : wb_dat_o[15: 8];

   assign wr_data[ 7: 0] = wb_sel_i[0] ? wb_dat_i[ 7: 0] : wb_dat_o[ 7: 0];

   wire ram_we;

   assign ram_we = wb_we_i & wb_ack_o;

   assign wb_dat_o = mem[adr];

   // Write logic

   always @ (posedge wb_clk_i)

     begin

        if (ram_we)

          mem[adr] <= wr_data;

     end

   // Ack Logic

   reg wb_ack_o_r;

   assign wb_ack_o = wb_ack_o_r & wb_stb_i &

                     !(burst_access_wrong_wb_adr | addr_err);

   always @ (posedge wb_clk_i)

     if (wb_rst_i)

       wb_ack_o_r <= 1'b0;

     else if (wb_cyc_i) // We have bus

       begin

          if (addr_err & wb_stb_i)

            begin

               wb_ack_o_r <= 1;

            end

          else if (wb_cti_i == 3'b000)

            begin

               // Classic cycle acks

               if (wb_stb_i)

                 begin

                    if (!wb_ack_o_r)

                      wb_ack_o_r <= 1;

                    else

                      wb_ack_o_r <= 0;

                 end

            end // if (wb_cti_i == 3'b000)

          else if ((wb_cti_i == 3'b001) | (wb_cti_i == 3'b010))

            begin

               // Increment/constant address bursts

               if (wb_stb_i)

                 wb_ack_o_r <= 1;

               else

                 wb_ack_o_r <= 0;

            end

          else if (wb_cti_i == 3'b111)

            begin

               // End of cycle

               if (!wb_ack_o_r)

                 wb_ack_o_r <= wb_stb_i;

               else

                 wb_ack_o_r <= 0;

            end

       end // if (wb_cyc_i)

     else

       wb_ack_o_r <= 0;

   //

   // Error signal generation

   //

   // Error when out of bounds of memory - skip top byte of address in case

   // this is mapped somewhere other than 0x00.

   assign addr_err  = wb_cyc_i & wb_stb_i & (|wb_adr_i[aw-1-8:mem_adr_width]);

   // OR in other errors here...

   assign wb_err_o =  wb_ack_o_r & wb_stb_i &

                      (burst_access_wrong_wb_adr | addr_err);

   //

   // Access functions

   //

   // Function to access RAM (for use by Verilator).

   function [31:0] get_mem32;

      // verilator public

      input [aw-1:0]             addr;

      get_mem32 = mem[addr];

   endfunction // get_mem32   

   // Function to access RAM (for use by Verilator).

   function [7:0] get_mem8;

      // verilator public

      input [aw-1:0]             addr;

            reg [31:0]           temp_word;

      begin

         temp_word = mem[{addr[aw-1:2],2'd0}];

         // Big endian mapping.

         get_mem8 = (addr[1:0]==2'b00) ? temp_word[31:24] :

                    (addr[1:0]==2'b01) ? temp_word[23:16] :

                    (addr[1:0]==2'b10) ? temp_word[15:8] : temp_word[7:0];

         end

   endfunction // get_mem8   

   // Function to write RAM (for use by Verilator).

   function set_mem32;

      // verilator public

      input [aw-1:0]             addr;

      input [dw-1:0]             data;

      mem[addr] = data;

   endfunction // set_mem32   

endmodule // ram_wb_b3