OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [ecos-2.0/] [doc/] [html/] [user-guide/] [setup-arm-pid.html] - Blame information for rev 773

Go to most recent revision | Details | Compare with Previous | View Log

Line No. Rev Author Line
1 28 unneback 
<!-- Copyright (C) 2003 Red Hat, Inc.                                -->
2 
<!-- This material may be distributed only subject to the terms      -->
3 
<!-- and conditions set forth in the Open Publication License, v1.0  -->
4 
<!-- or later (the latest version is presently available at          -->
5 
<!-- http://www.opencontent.org/openpub/).                           -->
6 
<!-- Distribution of the work or derivative of the work in any       -->
7 
<!-- standard (paper) book form is prohibited unless prior           -->
8 
<!-- permission is obtained from the copyright holder.               -->
9 
<HTML
10 
><HEAD
11 
><TITLE
12 
>ARM PID Hardware Setup</TITLE
13 
><meta name="MSSmartTagsPreventParsing" content="TRUE">
14 
<META
15 
NAME="GENERATOR"
16 
CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+
17 
"><LINK
18 
REL="HOME"
19 
TITLE="eCos User Guide"
20 
HREF="ecos-user-guide.html"><LINK
21 
REL="UP"
22 
TITLE="Target Setup"
23 
HREF="appendix-target-setup.html"><LINK
24 
REL="PREVIOUS"
25 
TITLE="SPARClite Architectural Simulator Setup"
26 
HREF="setup-sparclite-sim.html"><LINK
27 
REL="NEXT"
28 
TITLE="ARM AEB-1 Hardware Setup"
29 
HREF="setup-arm-aeb1.html"></HEAD
30 
><BODY
31 
CLASS="SECT1"
32 
BGCOLOR="#FFFFFF"
33 
TEXT="#000000"
34 
LINK="#0000FF"
35 
VLINK="#840084"
36 
ALINK="#0000FF"
37 
><DIV
38 
CLASS="NAVHEADER"
39 
><TABLE
40 
SUMMARY="Header navigation table"
41 
WIDTH="100%"
42 
BORDER="0"
43 
CELLPADDING="0"
44 
CELLSPACING="0"
45 
><TR
46 
><TH
47 
COLSPAN="3"
48 
ALIGN="center"
49 
>eCos User Guide</TH
50 
></TR
51 
><TR
52 
><TD
53 
WIDTH="10%"
54 
ALIGN="left"
55 
VALIGN="bottom"
56 
><A
57 
HREF="setup-sparclite-sim.html"
58 
ACCESSKEY="P"
59 
>Prev</A
60 
></TD
61 
><TD
62 
WIDTH="80%"
63 
ALIGN="center"
64 
VALIGN="bottom"
65 
>Appendix A. Target Setup</TD
66 
><TD
67 
WIDTH="10%"
68 
ALIGN="right"
69 
VALIGN="bottom"
70 
><A
71 
HREF="setup-arm-aeb1.html"
72 
ACCESSKEY="N"
73 
>Next</A
74 
></TD
75 
></TR
76 
></TABLE
77 
><HR
78 
ALIGN="LEFT"
79 
WIDTH="100%"></DIV
80 
><DIV
81 
CLASS="SECT1"
82 
><H1
83 
CLASS="SECT1"
84 
><A
85 
NAME="SETUP-ARM-PID">ARM PID Hardware Setup</H1
86 
><P
87 
>eCos comes with two ROM images that provide GDB support for
88 
the ARM PID board. The first ROM image provides a port of the CygMon
89 
ROM monitor, which includes a command-line interface and a GDB remote
90 
stub. The second ROM image provides a remote GDB stub only, which
91 
is a minimal environment for downloading and debugging eCos programs
92 
solely using GDB.</P
93 
><P
94 
>eCos, CygMon and the GDB stubs all support the PID fitted
95 
with both ARM7T and ARM9 daughterboards. CygMon and the stubs can
96 
be programmed into either the programmable ROM (U12) or the FLASH
97 
(U13). Pre-built forms of both ROM images are provided in the directory
98 
loaders/arm-pid under the root of your eCos installation,
99 
along with a tool that will program the stubs into the FLASH memory on
100 
the board. CygMon images are prefixed with the name 'cygmon' and
101 
GDB stub ROM images are given the prefix 'gdb_module'.
102 
Images may be provided in a number of formats including ELF (.img
103 
extension), binary (.bin extension) and SREC (.srec extension).
104 
Note that some unreliability has been experienced in downloading
105 
files using Angel 1.00. Angel 1.02 appears to be more robust in
106 
this application.</P
107 
><DIV
108 
CLASS="SECT2"
109 
><H2
110 
CLASS="SECT2"
111 
><A
112 
NAME="AEN3542">Installing the Stubs into FLASH</H2
113 
><DIV
114 
CLASS="SECT3"
115 
><H3
116 
CLASS="SECT3"
117 
><A
118 
NAME="AEN3544">Preparing the Binaries</H3
119 
><P
120 
>These two binary preparation steps are not strictly necessary
121 
as the eCos distribution ships with pre-compiled binaries in the
122 
directory loaders/arm-pid relative to the installation
123 
root.</P
124 
></DIV
125 
><DIV
126 
CLASS="SECT3"
127 
><H3
128 
CLASS="SECT3"
129 
><A
130 
NAME="AEN3547">Building the ROM images with the eCos Configuration Tool</H3
131 
><P
132 
></P
133 
><OL
134 
TYPE="1"
135 
><LI
136 
><P
137 
>Start with a new document - selecting the
138 
<SPAN
139 
CLASS="emphasis"
140 
><I
141 
CLASS="EMPHASIS"
142 
>File</I
143 
></SPAN
144 
>-&#62;<SPAN
145 
CLASS="emphasis"
146 
><I
147 
CLASS="EMPHASIS"
148 
>New</I
149 
></SPAN
150 
>
151 
 menu item if necessary to do this.</P
152 
></LI
153 
><LI
154 
><P
155 
>Choose the
156 
<SPAN
157 
CLASS="emphasis"
158 
><I
159 
CLASS="EMPHASIS"
160 
>Build</I
161 
></SPAN
162 
>
163 
-&#62;
164 
<SPAN
165 
CLASS="emphasis"
166 
><I
167 
CLASS="EMPHASIS"
168 
>Templates</I
169 
></SPAN
170 
>
171 
 menu item, and then select the ARM PID hardware.</P
172 
></LI
173 
><LI
174 
><P
175 
>While still displaying the
176 
<SPAN
177 
CLASS="emphasis"
178 
><I
179 
CLASS="EMPHASIS"
180 
>Build</I
181 
></SPAN
182 
>
183 
-&#62;
184 
<SPAN
185 
CLASS="emphasis"
186 
><I
187 
CLASS="EMPHASIS"
188 
>Templates</I
189 
></SPAN
190 
>
191 
 dialog box, select either the "stubs" package template to build
192 
a GDB stub image, or the "cygmon" template to build the CygMon ROM
193 
Monitor. Click
194 
<SPAN
195 
CLASS="emphasis"
196 
><I
197 
CLASS="EMPHASIS"
198 
>OK</I
199 
></SPAN
200 
>.</P
201 
></LI
202 
><LI
203 
><P
204 
>Build eCos using
205 
<SPAN
206 
CLASS="emphasis"
207 
><I
208 
CLASS="EMPHASIS"
209 
>Build</I
210 
></SPAN
211 
>
212 
-&#62;
213 
<SPAN
214 
CLASS="emphasis"
215 
><I
216 
CLASS="EMPHASIS"
217 
>Library</I
218 
></SPAN
219 
></P
220 
></LI
221 
><LI
222 
><P
223 
>When the build completes, the image files can be found
224 
in the bin/ subdirectory of the install tree. GDB stub
225 
ROM images have the prefix "gdb_module". CygMon images
226 
have the prefix "cygmon".</P
227 
></LI
228 
></OL
229 
></DIV
230 
><DIV
231 
CLASS="SECT3"
232 
><H3
233 
CLASS="SECT3"
234 
><A
235 
NAME="AEN3569">Building the ROM images with ecosconfig</H3
236 
><P
237 
></P
238 
><OL
239 
TYPE="1"
240 
><LI
241 
><P
242 
>                   Make an empty directory to contain the build tree,
243 
and cd into it.</P
244 
></LI
245 
><LI
246 
><P
247 
>To build a GDB stub ROM image, enter the command:</P
248 
><TABLE
249 
BORDER="5"
250 
BGCOLOR="#E0E0F0"
251 
WIDTH="70%"
252 
><TR
253 
><TD
254 
><PRE
255 
CLASS="PROGRAMLISTING"
256 
>$ ecosconfig new pid stubs</PRE
257 
></TD
258 
></TR
259 
></TABLE
260 
><P
261 
>or to build a CygMon ROM monitor image, enter the command:</P
262 
><TABLE
263 
BORDER="5"
264 
BGCOLOR="#E0E0F0"
265 
WIDTH="70%"
266 
><TR
267 
><TD
268 
><PRE
269 
CLASS="PROGRAMLISTING"
270 
>$ ecosconfig new pid cygmon</PRE
271 
></TD
272 
></TR
273 
></TABLE
274 
></LI
275 
><LI
276 
><P
277 
>Enter the commands:</P
278 
><TABLE
279 
BORDER="5"
280 
BGCOLOR="#E0E0F0"
281 
WIDTH="70%"
282 
><TR
283 
><TD
284 
><PRE
285 
CLASS="PROGRAMLISTING"
286 
>$ ecosconfig tree
287 
$ make</PRE
288 
></TD
289 
></TR
290 
></TABLE
291 
></LI
292 
><LI
293 
><P
294 
>When the build completes, the image files can be found
295 
in the bin/ subdirectory of the install tree. GDB stub
296 
ROM images have the prefix "gdb_module". CygMon images
297 
have the prefix "cygmon".</P
298 
></LI
299 
></OL
300 
></DIV
301 
><DIV
302 
CLASS="SECT3"
303 
><H3
304 
CLASS="SECT3"
305 
><A
306 
NAME="AEN3584">Building the FLASH Tool with the eCos Configuration Tool</H3
307 
><P
308 
></P
309 
><OL
310 
TYPE="1"
311 
><LI
312 
><P
313 
>Start with a new document - selecting the
314 
<SPAN
315 
CLASS="emphasis"
316 
><I
317 
CLASS="EMPHASIS"
318 
>File</I
319 
></SPAN
320 
>-&#62;<SPAN
321 
CLASS="emphasis"
322 
><I
323 
CLASS="EMPHASIS"
324 
>New</I
325 
></SPAN
326 
>
327 
 menu item if necessary to do this.</P
328 
></LI
329 
><LI
330 
><P
331 
>Choose the
332 
<SPAN
333 
CLASS="emphasis"
334 
><I
335 
CLASS="EMPHASIS"
336 
>Build</I
337 
></SPAN
338 
>-&#62;<SPAN
339 
CLASS="emphasis"
340 
><I
341 
CLASS="EMPHASIS"
342 
>Templates</I
343 
></SPAN
344 
>
345 
 menu item, and then select the ARM PID hardware.</P
346 
></LI
347 
><LI
348 
><P
349 
>Enable the "Build flash programming tool" option in the
350 
ARM PID HAL (CYGBLD_BUILD_FLASH_TOOL)
351 
and resolve any resulting configuration conflicts.</P
352 
></LI
353 
><LI
354 
><P
355 
>Build eCos using
356 
<SPAN
357 
CLASS="emphasis"
358 
><I
359 
CLASS="EMPHASIS"
360 
>Build</I
361 
></SPAN
362 
>
363 
-&#62;
364 
<SPAN
365 
CLASS="emphasis"
366 
><I
367 
CLASS="EMPHASIS"
368 
>Library</I
369 
></SPAN
370 
></P
371 
></LI
372 
><LI
373 
><P
374 
>When the build completes, the FLASH tool image file can
375 
be found in the bin/ subdirectory of the install tree,
376 
with the prefix "prog_flash"</P
377 
></LI
378 
></OL
379 
></DIV
380 
><DIV
381 
CLASS="SECT3"
382 
><H3
383 
CLASS="SECT3"
384 
><A
385 
NAME="AEN3603">Building the FLASH Tool with ecosconfig</H3
386 
><P
387 
></P
388 
><OL
389 
TYPE="1"
390 
><LI
391 
><P
392 
>                   Make an empty directory to contain the build tree,
393 
and cd into it
394 
                    </P
395 
></LI
396 
><LI
397 
><P
398 
>Enter the command:</P
399 
><TABLE
400 
BORDER="5"
401 
BGCOLOR="#E0E0F0"
402 
WIDTH="70%"
403 
><TR
404 
><TD
405 
><PRE
406 
CLASS="PROGRAMLISTING"
407 
>$ ecosconfig new pid</PRE
408 
></TD
409 
></TR
410 
></TABLE
411 
></LI
412 
><LI
413 
><P
414 
>Edit the file ecos.ecc and enable the option CYGBLD_BUILD_FLASH_TOOL
415 
by uncommenting its user_value property and setting it
416 
to 1.</P
417 
></LI
418 
><LI
419 
><P
420 
>Enter the commands:</P
421 
><TABLE
422 
BORDER="5"
423 
BGCOLOR="#E0E0F0"
424 
WIDTH="70%"
425 
><TR
426 
><TD
427 
><PRE
428 
CLASS="PROGRAMLISTING"
429 
>$ ecosconfig resolve</PRE
430 
></TD
431 
></TR
432 
></TABLE
433 
><P
434 
>[there will be some output]</P
435 
><TABLE
436 
BORDER="5"
437 
BGCOLOR="#E0E0F0"
438 
WIDTH="70%"
439 
><TR
440 
><TD
441 
><PRE
442 
CLASS="PROGRAMLISTING"
443 
>$ ecosconfig tree
444 
$ make</PRE
445 
></TD
446 
></TR
447 
></TABLE
448 
></LI
449 
><LI
450 
><P
451 
>When the build completes, the FLASH tool image file can
452 
be found in the bin/ subdirectory of the install tree,
453 
with the prefix "prog_flash"</P
454 
></LI
455 
></OL
456 
></DIV
457 
><DIV
458 
CLASS="SECT3"
459 
><H3
460 
CLASS="SECT3"
461 
><A
462 
NAME="AEN3620">Prepare the Board for FLASH Programming</H3
463 
><P
464 
>Each time a new image is to be programmed in the FLASH, the
465 
jumpers on the board must be set to allow Angel to run:</P
466 
><P
467 
></P
468 
><OL
469 
TYPE="1"
470 
><LI
471 
><P
472 
>                   Set jumper 7-8 on LK6   [using the Angel code
473 
in the 16 bit EPROM]</P
474 
></LI
475 
><LI
476 
><P
477 
>Set jumper 5-6 on LK6   [select 8bit ROM mode]</P
478 
></LI
479 
><LI
480 
><P
481 
>Set jumper LK18         [ROM remap - this is
482 
also required for eCos]</P
483 
></LI
484 
><LI
485 
><P
486 
>Set S1 to 0-0-1-1       [20MHz operation]</P
487 
></LI
488 
><LI
489 
><P
490 
>Open jumper LK4  [enable little-endian operation]
491 
 
492 
Attach a serial cable from Serial A on the PID board to connector
493 
1 on the development system. This is the cable through which the
494 
binaries will be downloaded. Attach a serial cable from Serial B
495 
on the PID board to connector 2 on the development system (or any
496 
system that will work as a terminal). Through this cable, the FLASH
497 
tool will write its instructions (at 38400 baud).</P
498 
></LI
499 
></OL
500 
></DIV
501 
><DIV
502 
CLASS="SECT3"
503 
><H3
504 
CLASS="SECT3"
505 
><A
506 
NAME="AEN3634">Program the FLASH</H3
507 
><P
508 
></P
509 
><OL
510 
TYPE="1"
511 
><LI
512 
><P
513 
>Download the FLASH ROM image onto the PID board. For
514 
example. for the GDB stubs image:
515 
 
516 
<TABLE
517 
BORDER="5"
518 
BGCOLOR="#E0E0F0"
519 
WIDTH="70%"
520 
><TR
521 
><TD
522 
><PRE
523 
CLASS="PROGRAMLISTING"
524 
>bash$ arm-elf-gdb -nw gdb_module.img
525 
GNU gdb 4.18-DEVTOOLSVERSION
526 
Copyright 1998 Free Software Foundation, Inc.
527 
GDB is free software, covered by the GNU General Public License,
528 
and you are welcome to change it and/or distribute copies
529 
of it under certain conditions. Type "show copying" to see the conditions.
530 
There is absolutely no warranty for GDB. Type "show warranty" for details.
531 
This GDB was configured as "--host=i586-pc-cygwin32 --target=arm-elf".
532 
(no debugging symbols found)...
533 
(gdb) target rdi s=com1
534 
Angel Debug Monitor for PID (Built with Serial(x1), Parallel, DCC) 1.00
535 
(Advanced RISC Machines SDT 2.10)
536 
Angel Debug Monitor rebuilt on Jan 20 1997 at 02:33:43
537 
Connected to ARM RDI target.
538 
(gdb) load
539 
Loading section .rom_vectors, size 0x44 lma 0x60000
540 
Loading section .text, size 0x1f3c lma 0x60044
541 
Loading section .rodata, size 0x2c lma 0x61f80
542 
Loading section .data, size 0x124 lma 0x61fac
543 
Start address 0x60044 , load size 8400
544 
Transfer rate: 5169 bits/sec.
545 
(gdb) q
546 
The program is running.  Exit anyway? (y or n) y </PRE
547 
></TD
548 
></TR
549 
></TABLE
550 
>
551 
 
552 
<DIV
553 
CLASS="NOTE"
554 
><BLOCKQUOTE
555 
CLASS="NOTE"
556 
><P
557 
><B
558 
>Note: </B
559 
> On a UNIX or Linux system, the serial port must be
560 
 /dev/ttyS0 instead of COM1.
561 
 You need to make sure that the /dev/ttyS0 files
562 
have the right permissions:
563 
<TABLE
564 
BORDER="5"
565 
BGCOLOR="#E0E0F0"
566 
WIDTH="70%"
567 
><TR
568 
><TD
569 
><PRE
570 
CLASS="SCREEN"
571 
>$ su
572 
 Password:
573 
 # chmod o+rw /dev/ttyS0*
574 
 # exit
575 
                      </PRE
576 
></TD
577 
></TR
578 
></TABLE
579 
>
580 
If you are programming the GDB stub image, it will now be located
581 
at 0x60000..0x64000. If you are programming the Cygmon ROM Monitor,
582 
it will be located at 0x60000..0x80000.</P
583 
></BLOCKQUOTE
584 
></DIV
585 
></P
586 
></LI
587 
><LI
588 
><P
589 
>Now download the FLASH programmer tool</P
590 
><TABLE
591 
BORDER="5"
592 
BGCOLOR="#E0E0F0"
593 
WIDTH="70%"
594 
><TR
595 
><TD
596 
><PRE
597 
CLASS="PROGRAMLISTING"
598 
>bash$ arm-elf-gdb prog_flash.img
599 
GNU gdb 4.18-DEVTOOLSVERSION
600 
Copyright 1998 Free Software Foundation, Inc.
601 
GDB is free software, covered by the GNU General Public License,
602 
and you are welcome to change it and/or distribute
603 
copies of it under certain conditions. Type "show copying" to see
604 
the conditions. There is absolutely no warranty for GDB.  Type "show
605 
warranty" for details.
606 
This GDB was configured as "--host=i586-pc-cygwin32 --target=arm-elf".
607 
(gdb) target rdi s=com1
608 
Angel Debug Monitor for PID (Built with Serial(x1), Parallel, DCC) 1.00
609 
(Advanced RISC Machines SDT 2.10)
610 
Angel Debug Monitor rebuilt on Jan 20 1997 at 02:33:43
611 
Connected to ARM RDI target.
612 
(gdb) load
613 
Loading section .rom_vectors, size 0x44 lma 0x40000
614 
Loading section .text, size 0x44a4 lma 0x40044
615 
Loading section .rodata, size 0x318 lma 0x444e8
616 
Loading section .data, size 0x1c8 lma 0x44800
617 
Start address 0x40044 , load size 18888
618 
Transfer rate: 5596 bits/sec.
619 
(gdb) c</PRE
620 
></TD
621 
></TR
622 
></TABLE
623 
></LI
624 
><LI
625 
><P
626 
>The FLASH tool will output some text on the board serial
627 
port B at 38400 baud:</P
628 
><TABLE
629 
BORDER="5"
630 
BGCOLOR="#E0E0F0"
631 
WIDTH="70%"
632 
><TR
633 
><TD
634 
><PRE
635 
CLASS="PROGRAMLISTING"
636 
>ARM
637 
eCos
638 
 
639 
FLASH here!
640 
manuf: 8, device: 40
641 
Error: Wrong Manufaturer: 08
642 
... Please change FLASH jumper</PRE
643 
></TD
644 
></TR
645 
></TABLE
646 
></LI
647 
><LI
648 
><P
649 
>This text is repeated until you remove the jumper 7-8
650 
on LK6. Then the output will be:</P
651 
><TABLE
652 
BORDER="5"
653 
BGCOLOR="#E0E0F0"
654 
WIDTH="70%"
655 
><TR
656 
><TD
657 
><PRE
658 
CLASS="PROGRAMLISTING"
659 
>manuf: 1F, device: A4
660 
AT29C040A recognised
661 
About to program FLASH using data at 60000..64000
662 
*** Press RESET now to abort!</PRE
663 
></TD
664 
></TR
665 
></TABLE
666 
></LI
667 
><LI
668 
><P
669 
> You have about 10 seconds to abort the operation by pressing
670 
reset. After this timeout, the FLASH programming happens:</P
671 
><TABLE
672 
BORDER="5"
673 
BGCOLOR="#E0E0F0"
674 
WIDTH="70%"
675 
><TR
676 
><TD
677 
><PRE
678 
CLASS="SCREEN"
679 
>...Programming FLASH
680 
All done!</PRE
681 
></TD
682 
></TR
683 
></TABLE
684 
></LI
685 
><LI
686 
><P
687 
>Quit/kill the GDB process, which will hang.</P
688 
></LI
689 
><LI
690 
><P
691 
>Next time you reset the board, the stub will be in control,
692 
communicating on Serial A at 38400 baud.</P
693 
></LI
694 
></OL
695 
><DIV
696 
CLASS="NOTE"
697 
><BLOCKQUOTE
698 
CLASS="NOTE"
699 
><P
700 
><B
701 
>Note: </B
702 
>If you do not have two serial ports available on your host
703 
computer, you may still verify the FLASH programming completed successfully
704 
by quitting/killing the GDB process after running "c" in
705 
step 2 above. Then switch the serial cable on the PID from Serial
706 
A to Serial B and run a terminal emulator on the host computer.
707 
In a few seconds you should see the the repeated text described
708 
in step 2 above and you may continue the remaining steps as normal.</P
709 
></BLOCKQUOTE
710 
></DIV
711 
></DIV
712 
><DIV
713 
CLASS="SECT3"
714 
><H3
715 
CLASS="SECT3"
716 
><A
717 
NAME="AEN3661">Programming the FLASH for big-endian mode</H3
718 
><P
719 
>The process is almost identical to the previous instructions
720 
which apply to a PID board running in little-endian mode only.</P
721 
><P
722 
>The only adjustments to make are that if programming a <SPAN
723 
CLASS="emphasis"
724 
><I
725 
CLASS="EMPHASIS"
726 
>GDB</I
727 
></SPAN
728 
> stub
729 
ROM image (or CygMon ROM monitor image), you must enable the option "Use
730 
Big-endian mode" in the <SPAN
731 
CLASS="emphasis"
732 
><I
733 
CLASS="EMPHASIS"
734 
>eCos Configuration Tool</I
735 
></SPAN
736 
> (CYGHWR_HAL_ARM_BIGENDIAN
737 
if using ecosconfig and editing ecos.ecc).</P
738 
><P
739 
>When programming the FLASH there are two options:</P
740 
><P
741 
></P
742 
><OL
743 
TYPE="1"
744 
><LI
745 
><P
746 
>Program FLASH using the little-endian FLASH tool. After
747 
powering off, replace the ROM controller with the special big-endian
748 
version which can be acquired from ARM. (This has not been tested
749 
by Red Hat).</P
750 
></LI
751 
><LI
752 
><P
753 
>Use a special big-endian version of the FLASH tool which
754 
byte-swaps all the words as they are written to the FLASH.</P
755 
></LI
756 
></OL
757 
><P
758 
>Build this tool by enabling the "Build flash programming tool
759 
for BE images on LE boards" option (CYGBLD_BUILD_FLASH_TOOL_BE),
760 
resulting in a utility with the prefix "prog_flash_BE_image_LE_system"
761 
which should be used instead of "prog_flash".</P
762 
><P
763 
>Note that there is a limitation to this method: no sub-word
764 
data can be read from the ROM. To work around this, the .rodata
765 
section is folded into the .data section and thus copied to RAM
766 
before the system starts.</P
767 
><P
768 
>Given that Thumb instructions are 16 bit, it is not possible
769 
to run ROM-startup Thumb binaries on the PID board using this method.</P
770 
><P
771 
>When the image has been programmed, power off the board, and
772 
set jumper LK4 to enable big-endian operation.</P
773 
></DIV
774 
></DIV
775 
><DIV
776 
CLASS="SECT2"
777 
><H2
778 
CLASS="SECT2"
779 
><A
780 
NAME="AEN3677">Installing the Stubs into ROM</H2
781 
><P
782 
></P
783 
><OL
784 
TYPE="1"
785 
><LI
786 
><P
787 
>Program the binary image file gdb_module.bin
788 
into ROM referring to the instructions of your ROM programmer.</P
789 
></LI
790 
><LI
791 
><P
792 
>Plug the ROM into socket U12 and install jumper LK6 pins
793 
7-8 to enable the ROM.</P
794 
></LI
795 
></OL
796 
></DIV
797 
></DIV
798 
><DIV
799 
CLASS="NAVFOOTER"
800 
><HR
801 
ALIGN="LEFT"
802 
WIDTH="100%"><TABLE
803 
SUMMARY="Footer navigation table"
804 
WIDTH="100%"
805 
BORDER="0"
806 
CELLPADDING="0"
807 
CELLSPACING="0"
808 
><TR
809 
><TD
810 
WIDTH="33%"
811 
ALIGN="left"
812 
VALIGN="top"
813 
><A
814 
HREF="setup-sparclite-sim.html"
815 
ACCESSKEY="P"
816 
>Prev</A
817 
></TD
818 
><TD
819 
WIDTH="34%"
820 
ALIGN="center"
821 
VALIGN="top"
822 
><A
823 
HREF="ecos-user-guide.html"
824 
ACCESSKEY="H"
825 
>Home</A
826 
></TD
827 
><TD
828 
WIDTH="33%"
829 
ALIGN="right"
830 
VALIGN="top"
831 
><A
832 
HREF="setup-arm-aeb1.html"
833 
ACCESSKEY="N"
834 
>Next</A
835 
></TD
836 
></TR
837 
><TR
838 
><TD
839 
WIDTH="33%"
840 
ALIGN="left"
841 
VALIGN="top"
842 
>SPARClite Architectural Simulator Setup</TD
843 
><TD
844 
WIDTH="34%"
845 
ALIGN="center"
846 
VALIGN="top"
847 
><A
848 
HREF="appendix-target-setup.html"
849 
ACCESSKEY="U"
850 
>Up</A
851 
></TD
852 
><TD
853 
WIDTH="33%"
854 
ALIGN="right"
855 
VALIGN="top"
856 
>ARM AEB-1 Hardware Setup</TD
857 
></TR
858 
></TABLE
859 
></DIV
860 
></BODY
861 
></HTML
862 
>

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.