OpenCores
URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [ecos-2.0/] [doc/] [html/] [user-guide/] [setup-tx49-ref4955.html] - Blame information for rev 773

Go to most recent revision | Details | Compare with Previous | View Log

Line No. Rev Author Line
1 28 unneback 
<!-- Copyright (C) 2003 Red Hat, Inc.                                -->
2 
<!-- This material may be distributed only subject to the terms      -->
3 
<!-- and conditions set forth in the Open Publication License, v1.0  -->
4 
<!-- or later (the latest version is presently available at          -->
5 
<!-- http://www.opencontent.org/openpub/).                           -->
6 
<!-- Distribution of the work or derivative of the work in any       -->
7 
<!-- standard (paper) book form is prohibited unless prior           -->
8 
<!-- permission is obtained from the copyright holder.               -->
9 
<HTML
10 
><HEAD
11 
><TITLE
12 
>TX49 Hardware Setup</TITLE
13 
><meta name="MSSmartTagsPreventParsing" content="TRUE">
14 
<META
15 
NAME="GENERATOR"
16 
CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+
17 
"><LINK
18 
REL="HOME"
19 
TITLE="eCos User Guide"
20 
HREF="ecos-user-guide.html"><LINK
21 
REL="UP"
22 
TITLE="Target Setup"
23 
HREF="appendix-target-setup.html"><LINK
24 
REL="PREVIOUS"
25 
TITLE="TX39 Architectural Simulator Setup"
26 
HREF="setup-tx39-sim.html"><LINK
27 
REL="NEXT"
28 
TITLE="VR4300 Hardware Setup"
29 
HREF="setup-vr4300-vrc4373.html"></HEAD
30 
><BODY
31 
CLASS="SECT1"
32 
BGCOLOR="#FFFFFF"
33 
TEXT="#000000"
34 
LINK="#0000FF"
35 
VLINK="#840084"
36 
ALINK="#0000FF"
37 
><DIV
38 
CLASS="NAVHEADER"
39 
><TABLE
40 
SUMMARY="Header navigation table"
41 
WIDTH="100%"
42 
BORDER="0"
43 
CELLPADDING="0"
44 
CELLSPACING="0"
45 
><TR
46 
><TH
47 
COLSPAN="3"
48 
ALIGN="center"
49 
>eCos User Guide</TH
50 
></TR
51 
><TR
52 
><TD
53 
WIDTH="10%"
54 
ALIGN="left"
55 
VALIGN="bottom"
56 
><A
57 
HREF="setup-tx39-sim.html"
58 
ACCESSKEY="P"
59 
>Prev</A
60 
></TD
61 
><TD
62 
WIDTH="80%"
63 
ALIGN="center"
64 
VALIGN="bottom"
65 
>Appendix A. Target Setup</TD
66 
><TD
67 
WIDTH="10%"
68 
ALIGN="right"
69 
VALIGN="bottom"
70 
><A
71 
HREF="setup-vr4300-vrc4373.html"
72 
ACCESSKEY="N"
73 
>Next</A
74 
></TD
75 
></TR
76 
></TABLE
77 
><HR
78 
ALIGN="LEFT"
79 
WIDTH="100%"></DIV
80 
><DIV
81 
CLASS="SECT1"
82 
><H1
83 
CLASS="SECT1"
84 
><A
85 
NAME="SETUP-TX49-REF4955">TX49 Hardware Setup</H1
86 
><P
87 
>The eCos installation CD contains a copy of the eCos GDB stubs
88 
in  SREC format which must be programmed into the board&#8217;s
89 
FLASH memory.</P
90 
><DIV
91 
CLASS="SECT2"
92 
><H2
93 
CLASS="SECT2"
94 
><A
95 
NAME="AEN3296">Preparing the GDB stubs</H2
96 
><P
97 
>These stub preparation steps are not strictly necessary as
98 
the eCos distribution ships with pre-compiled stubs in the directory <TT
99 
CLASS="FILENAME"
100 
>loaders/tx49-ref4955</TT
101 
> relative
102 
to the installation root.</P
103 
><DIV
104 
CLASS="SECT3"
105 
><H3
106 
CLASS="SECT3"
107 
><A
108 
NAME="AEN3300">Building the GDB stub image with the eCos Configuration Tool</H3
109 
><P
110 
></P
111 
><OL
112 
TYPE="1"
113 
><LI
114 
><P
115 
>                 Start with a new document - selecting the
116 
<SPAN
117 
CLASS="emphasis"
118 
><I
119 
CLASS="EMPHASIS"
120 
>File-&#62;New</I
121 
></SPAN
122 
>
123 
 menu item if necessary to do this.</P
124 
></LI
125 
><LI
126 
><P
127 
>Choose the
128 
<SPAN
129 
CLASS="emphasis"
130 
><I
131 
CLASS="EMPHASIS"
132 
>Build-&#62;Templates</I
133 
></SPAN
134 
>
135 
 menu item, and then select the TX49 REF4955 hardware.</P
136 
></LI
137 
><LI
138 
><P
139 
>While still displaying the
140 
<SPAN
141 
CLASS="emphasis"
142 
><I
143 
CLASS="EMPHASIS"
144 
>Build-&#62;Templates</I
145 
></SPAN
146 
>
147 
 dialog box, select the stubs package template to build a GDB stub.
148 
Click
149 
<SPAN
150 
CLASS="emphasis"
151 
><I
152 
CLASS="EMPHASIS"
153 
>OK</I
154 
></SPAN
155 
>.</P
156 
></LI
157 
><LI
158 
><P
159 
>Build eCos stubs using
160 
<SPAN
161 
CLASS="emphasis"
162 
><I
163 
CLASS="EMPHASIS"
164 
>Build-&#62;Library</I
165 
></SPAN
166 
>.</P
167 
></LI
168 
><LI
169 
><P
170 
>When the build completes, the image files can be found
171 
in the bin/ subdirectory of the install tree. GDB stub
172 
images have the prefix gdb_module.</P
173 
></LI
174 
></OL
175 
></DIV
176 
><DIV
177 
CLASS="SECT3"
178 
><H3
179 
CLASS="SECT3"
180 
><A
181 
NAME="AEN3318">Building the GDB stub image with ecosconfig</H3
182 
><P
183 
></P
184 
><OL
185 
TYPE="1"
186 
><LI
187 
><P
188 
>                 Make an empty directory to contain the build tree,
189 
                  and cd into it.</P
190 
></LI
191 
><LI
192 
><P
193 
>To build a GDB stub ROM image, enter the command:</P
194 
><TABLE
195 
BORDER="5"
196 
BGCOLOR="#E0E0F0"
197 
WIDTH="70%"
198 
><TR
199 
><TD
200 
><PRE
201 
CLASS="PROGRAMLISTING"
202 
>$ ecosconfig new ref4955 stubs </PRE
203 
></TD
204 
></TR
205 
></TABLE
206 
></LI
207 
><LI
208 
><P
209 
>Enter the commands:</P
210 
><TABLE
211 
BORDER="5"
212 
BGCOLOR="#E0E0F0"
213 
WIDTH="70%"
214 
><TR
215 
><TD
216 
><PRE
217 
CLASS="PROGRAMLISTING"
218 
>$ ecosconfig tree
219 
$ make</PRE
220 
></TD
221 
></TR
222 
></TABLE
223 
></LI
224 
><LI
225 
><P
226 
>When the build completes, the image files can be found
227 
in the bin/ subdirectory of the install tree. GDB stub
228 
images have the prefix gdb_module.</P
229 
></LI
230 
></OL
231 
></DIV
232 
></DIV
233 
><DIV
234 
CLASS="SECT2"
235 
><H2
236 
CLASS="SECT2"
237 
><A
238 
NAME="AEN3331">Installing GDB stubs into FLASH</H2
239 
><P
240 
>Boot into the board&#8217;s firmware in little-endian mode:</P
241 
><P
242 
>Set the switches like this:   </P
243 
><P
244 
>SW1: 10000000 (first lever up, the rest down)
245 
SW2: 10000010</P
246 
><P
247 
>Connect serial cable on the lower connector, configure terminal
248 
emulator for 38400, 8-N-1.</P
249 
><P
250 
>When booting the board, you should get this prompt:</P
251 
><TABLE
252 
BORDER="5"
253 
BGCOLOR="#E0E0F0"
254 
WIDTH="70%"
255 
><TR
256 
><TD
257 
><PRE
258 
CLASS="PROGRAMLISTING"
259 
>HCP5 rev 0.9B .
260 
HCP5?</PRE
261 
></TD
262 
></TR
263 
></TABLE
264 
><P
265 
>Select o (option), a (FLASH) and b (boot write). You should
266 
see this:</P
267 
><TABLE
268 
BORDER="5"
269 
BGCOLOR="#E0E0F0"
270 
WIDTH="70%"
271 
><TR
272 
><TD
273 
><PRE
274 
CLASS="PROGRAMLISTING"
275 
>Boot ROM Write
276 
ROM address-ffffffffbd000000, Boot Bus-[32bit]
277 
ID2 0 4 ffffffffa002ad40
278 
zzz SS-40000 IV-1 CS-20000 CC-2
279 
Flash ROM-[28F640J5], [16bit chip] * 2 * 1
280 
Block size-00040000  count-64
281 
ROM adr ffffffffbd000000-ffffffffbe000000  mask-00fc0000
282 
Send Srecord file sa=00000000 size=ffffffffffffffff
283 
ra=fffffffffe000000
284 
          </PRE
285 
></TD
286 
></TR
287 
></TABLE
288 
><P
289 
>Now send the stub SREC data down to the board using the terminal
290 
 emulator&#8217;s &#8216;send ASCII&#8217; (or similar)
291 
functionality. </P
292 
><P
293 
>Red Hat has experienced some sensitivity to how fast the data
294 
is written to the board. Under Windows you should configure Minicom
295 
to use a line delay of 100 milliseconds. Under Linux, use the slow_cat.tcl
296 
 script:</P
297 
><TABLE
298 
BORDER="5"
299 
BGCOLOR="#E0E0F0"
300 
WIDTH="70%"
301 
><TR
302 
><TD
303 
><PRE
304 
CLASS="PROGRAMLISTING"
305 
>% cd BASE_DIR/packages/hal/mips/ref4955/<TT
306 
CLASS="REPLACEABLE"
307 
><I
308 
>&#60;version&#62;</I
309 
></TT
310 
>/misc
311 
% slow_cat.tcl &lt; [path]/gdb_module.srec &#62; /dev/ttyS0</PRE
312 
></TD
313 
></TR
314 
></TABLE
315 
><P
316 
>Power off the board, and change it to boot the GDB stubs in
317 
big-endian mode by setting the switches like this:</P
318 
><P
319 
>SW1: 00000000 (all levers down)
320 
SW2: 10001010</P
321 
><P
322 
>The GDB stubs allow communication with GDB using the serial
323 
port at connector PJ7A (lower connector). The communication parameters
324 
are  fixed at 38400 baud, 8 data bits, no parity bit and 1 stop
325 
bit  (8-N-1). No flow control is employed. Connection to the host
326 
computer should be made using a straight through serial cable.</P
327 
></DIV
328 
></DIV
329 
><DIV
330 
CLASS="NAVFOOTER"
331 
><HR
332 
ALIGN="LEFT"
333 
WIDTH="100%"><TABLE
334 
SUMMARY="Footer navigation table"
335 
WIDTH="100%"
336 
BORDER="0"
337 
CELLPADDING="0"
338 
CELLSPACING="0"
339 
><TR
340 
><TD
341 
WIDTH="33%"
342 
ALIGN="left"
343 
VALIGN="top"
344 
><A
345 
HREF="setup-tx39-sim.html"
346 
ACCESSKEY="P"
347 
>Prev</A
348 
></TD
349 
><TD
350 
WIDTH="34%"
351 
ALIGN="center"
352 
VALIGN="top"
353 
><A
354 
HREF="ecos-user-guide.html"
355 
ACCESSKEY="H"
356 
>Home</A
357 
></TD
358 
><TD
359 
WIDTH="33%"
360 
ALIGN="right"
361 
VALIGN="top"
362 
><A
363 
HREF="setup-vr4300-vrc4373.html"
364 
ACCESSKEY="N"
365 
>Next</A
366 
></TD
367 
></TR
368 
><TR
369 
><TD
370 
WIDTH="33%"
371 
ALIGN="left"
372 
VALIGN="top"
373 
>TX39 Architectural Simulator Setup</TD
374 
><TD
375 
WIDTH="34%"
376 
ALIGN="center"
377 
VALIGN="top"
378 
><A
379 
HREF="appendix-target-setup.html"
380 
ACCESSKEY="U"
381 
>Up</A
382 
></TD
383 
><TD
384 
WIDTH="33%"
385 
ALIGN="right"
386 
VALIGN="top"
387 
>VR4300 Hardware Setup</TD
388 
></TR
389 
></TABLE
390 
></DIV
391 
></BODY
392 
></HTML
393 
>

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.