Subversion Repositories openrisc

===========================================================================

#####ECOSGPLCOPYRIGHTBEGIN####

## -------------------------------------------

## This file is part of eCos, the Embedded Configurable Operating System.

## Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.

##

## eCos is free software; you can redistribute it and/or modify it under

## the terms of the GNU General Public License as published by the Free

## Software Foundation; either version 2 or (at your option) any later version.

##

## eCos is distributed in the hope that it will be useful, but WITHOUT ANY

## WARRANTY; without even the implied warranty of MERCHANTABILITY or

## FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License

## for more details.

##

## You should have received a copy of the GNU General Public License along

## with eCos; if not, write to the Free Software Foundation, Inc.,

## 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.

##

## As a special exception, if other files instantiate templates or use macros

## or inline functions from this file, or you compile this file and link it

## with other works to produce a work based on this file, this file does not

## by itself cause the resulting work to be covered by the GNU General Public

## License. However the source code for this file must still be made available

## in accordance with section (3) of the GNU General Public License.

##

## This exception does not invalidate any other reasons why a work based on

## this file might be covered by the GNU General Public License.

##

## Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.

## at http://sources.redhat.com/ecos/ecos-license/

## -------------------------------------------

#####ECOSGPLCOPYRIGHTEND####

===========================================================================

28 Jan 2000

How to build and install CygMon on the PID

Make CygMon image

~~~~~~~~~~~~~~~~~

Configure and build using the 'cygmon' template for the PID

target. These are the necessary CLI instructions. It can also be done

from the Configtool by selecting the appropriate templates.

 % cd /tmp

 % mkdir cygmon

 % cd cygmon

 % ecosconfig new pid cygmon

 % ecosconfig tree

 % make

This will install some files in ./install/bin:

 cygmon.elf:   The built CygMon image

 cygmon.bin:   The image converted to binary (suitable for burning to ROM)

 cygmon.img:   The relocated ELF image (suitable for FLASH writing, see below)

 cygmon.srec:  The image converted to srecords

Make FLASH tool

~~~~~~~~~~~~~~~

Again, these are the necessary CLI instructions. It can also be done

from the Configtool by selecting the appropriate templates, and

enabling the option.

 % cd /tmp

 % mkdir pid-flash

 % cd pid-flash

 % ecosconfig new pid

 % 

      --- ecos.ecc.orig       Fri Jan 28 11:21:43 2000

      +++ ecos.ecc            Fri Jan 28 11:22:01 2000

      @@ -150,7 +150,7 @@

       cdl_option CYGBLD_BUILD_FLASH_TOOL {

           # Flavor: bool

           # No user value, uncomment the following line to provide one.

      -    # user_value 0

      +    user_value 1

           # value_source default

           # Default value: 0

           # Requires:  CYG_HAL_STARTUP == "RAM"

 % ecosconfig resolve

 % ecosconfig tree

 % make

The flash tool is installed in ./install/bin

Prepare board for CygMon

~~~~~~~~~~~~~~~~~~~~~~~~

 1. Set jumper 7-8 on LK6   [using the Angle code in the 16 bit EPROM]

 2. Set jumper 5-6 on LK6   [select 8bit ROM mode]

 3. Set jumper LK18         [ROM remap - this is also required for eCos]

 4. Set S1 to 0-0-1-1       [20MHz operation]

Program FLASH

~~~~~~~~~~~~~

 1. Download the CygMon relocated image onto the PID board:

      % cd /tmp

      % arm-elf-gdb -nw cygmon/install/bin/cygmon.img

        (gdb) target rdi s=

        Angel Debug Monitor V1.04 (Advanced RISC Machines SDT 2.11a) for PID

        Built with Serial(x1), Parallel, DCC

        Rebuilt on Apr  7 1998 at 22:20:43

        Serial Rate:   9600

        Connected to ARM RDI target.

        (gdb) load

        Loading section .rom_vectors, size 0x60 lma 0x60000

        Loading section .text, size 0xeea8 lma 0x60060

        Loading section .rodata, size 0x304c lma 0x6ef08

        Loading section .data, size 0x7f8 lma 0x71f54

        Start address 0x60060 , load size 75596

        Transfer rate: 5548 bits/sec.

        (gdb) quit

   This will download the stubs onto the board at 0x60000..0x80000

   Use /dev/ttyS0, COM1 or similar for the  name.

 2. Now download the FLASH programmer tool

      % arm-elf-gdb -nw pid-flash/install/bin/prog_flash.img

        (gdb) target rdi s=

        Angel Debug Monitor V1.04 (Advanced RISC Machines SDT 2.11a) for PID

        Built with Serial(x1), Parallel, DCC

        Rebuilt on Apr  7 1998 at 22:20:43

        Serial Rate:   9600

        Connected to ARM RDI target.

        (gdb) load

        Loading section .rom_vectors, size 0x60 lma 0x4000

        Loading section .text, size 0x4964 lma 0x4060

        Loading section .rodata, size 0x384 lma 0x89c4

        Loading section .data, size 0x28c lma 0x8d48

        Start address 0x4060 , load size 20436

        Transfer rate: 5449 bits/sec.

        (gdb) cont

 3. The FLASH tool will output some text on the board serial port B at

    38400 baud:

       ARM eCos

       FLASH here!

       manuf: 8, device: 40

       Error: Wrong Manufaturer: 08

       ... Please change FLASH jumper

 4. This text is repeated until you remove the jumper 7-8 on LK6. Then

    the output should be:

       manuf: 1F, device: A4

       AT29C040A recognised

       About to program FLASH using data at 60000..80000

       *** Press RESET now to abort!

 5. You have about 10 seconds to abort the operation by pressing

    reset. After this timeout, the FLASH programming happens:

      ...Programming FLASH

      All done!

 6. Quit/kill the GDB process which will hang.

 7. Next time you reset the board, CygMon will be in control, communicating

    on serial port A at 38400 baud. See documentation for further details

    on how to connect with GDB.