Subversion Repositories openrisc_me

##=============================================================================

##

##      edk.S

##

##      EDK board hardware setup

##

##=============================================================================

#####ECOSGPLCOPYRIGHTBEGIN####

## -------------------------------------------

## This file is part of eCos, the Embedded Configurable Operating System.

## Copyright (C) 1998, 1999, 2000, 2001, 2002 Red Hat, Inc.

##

## eCos is free software; you can redistribute it and/or modify it under

## the terms of the GNU General Public License as published by the Free

## Software Foundation; either version 2 or (at your option) any later version.

##

## eCos is distributed in the hope that it will be useful, but WITHOUT ANY

## WARRANTY; without even the implied warranty of MERCHANTABILITY or

## FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License

## for more details.

##

## You should have received a copy of the GNU General Public License along

## with eCos; if not, write to the Free Software Foundation, Inc.,

## 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.

##

## As a special exception, if other files instantiate templates or use macros

## or inline functions from this file, or you compile this file and link it

## with other works to produce a work based on this file, this file does not

## by itself cause the resulting work to be covered by the GNU General Public

## License. However the source code for this file must still be made available

## in accordance with section (3) of the GNU General Public License.

##

## This exception does not invalidate any other reasons why a work based on

## this file might be covered by the GNU General Public License.

##

## Alternative licenses for eCos may be arranged by contacting Red Hat, Inc.

## at http://sources.redhat.com/ecos/ecos-license/

## -------------------------------------------

#####ECOSGPLCOPYRIGHTEND####

##=============================================================================

#######DESCRIPTIONBEGIN####

##

## Author(s):   jskov

## Contributors:jskov

## Date:        1999-05-03

## Purpose:     EDK7708 board hardware setup

## Description: This file contains any code needed to initialize the

##              hardware on a Hitachi SH3 EDK7708 board.

##

######DESCRIPTIONEND####

##

##=============================================================================

#include 

#include 

        .globl  _hal_hardware_init

_hal_hardware_init:

        // Set up the Bus State Controller

        mov.l    $BSC_settings_table,r3

1:      mov.w    @r3+,r0                // Address (or zero)

        cmp/eq   #0,r0

        bt       2f

        mov.w    @r3+,r1                // data

        bra      1b

         mov.w    r1,@r0                // delay slot

2:

        rts

         nop

        .align  2

$BSC_settings_table:

        .long   BSC_settings_table

BSC_settings_table:

        # These are the settings set by the Hitachi ROM Monitor.

        # BCR2: Bus size of areas 1-6 to 32 bits

        .word   CYGARC_REG_BCR2

        .word   0x3ffc

        # BCR1: Areas 2 and 3 are SDRAM

        .word   CYGARC_REG_BCR1

        .word   0x080c

        # BCR2: Bus size of areas 1-6 to 32 bits [note: second write!]

        .word   CYGARC_REG_BCR2

        .word   0x3ffc

        # WCR1: 3 wait-state cycles inserted for all areas

        .word   CYGARC_REG_WCR1

        .word   0x3fff

        # WCR2: extra wait states and full pitch for burst

        .word   CYGARC_REG_WCR2

        .word   0xffd7

        # MCR: RAS/CAS & burst timing area 2/3

        .word   CYGARC_REG_MCR

        .word   0x963c

#if 0

        # DCR: RAS/CAS & burst timing area 2

        .word   CYGARC_REG_DCR

        .word   0x0000

        # PCR: PCMCIA disabled

        .word   CYGARC_REG_PCR

        .word   0x0000

#endif

        # RTCNT: refresh counter (needs a5 in top byte to accept write)

        .word   CYGARC_REG_RTCNT

        .word   (0xa500 | 0x0000)

        # RTCOR: refresh time constant (needs a5 in top byte to accept write)

        .word   CYGARC_REG_RTCOR

        .word   (0xa500 | 0x003b)

        # RFCR:  refresh count register (needs a4 in top byte to accept write)

        .word   CYGARC_REG_RFCR

        .word   (0xa400 | 0x0000)

        # RTCSR: refresh timer control (needs a5 in top byte to accept write)

        .word   CYGARC_REG_RTCSR

        .word   (0xa500 | 0x0008)

        # Set SDMR to 0x220

        .word    0xd880

        .word    0

        # Table end

        .word   0

#------------------------------------------------------------------------------

# end of edk.S