Subversion Repositories openrisc

#ifndef CYGONCE_AAED2000_H

#define CYGONCE_AAED2000_H

/*=============================================================================

//

//      aaed2000.h

//

//      Platform specific support (register layout, etc)

//

//=============================================================================

// ####ECOSGPLCOPYRIGHTBEGIN####

// -------------------------------------------

// This file is part of eCos, the Embedded Configurable Operating System.

// Copyright (C) 1998, 1999, 2000, 2001, 2002 Free Software Foundation, Inc.

//

// eCos is free software; you can redistribute it and/or modify it under

// the terms of the GNU General Public License as published by the Free

// Software Foundation; either version 2 or (at your option) any later

// version.

//

// eCos is distributed in the hope that it will be useful, but WITHOUT

// ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or

// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License

// for more details.

//

// You should have received a copy of the GNU General Public License

// along with eCos; if not, write to the Free Software Foundation, Inc.,

// 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.

//

// As a special exception, if other files instantiate templates or use

// macros or inline functions from this file, or you compile this file

// and link it with other works to produce a work based on this file,

// this file does not by itself cause the resulting work to be covered by

// the GNU General Public License. However the source code for this file

// must still be made available in accordance with section (3) of the GNU

// General Public License v2.

//

// This exception does not invalidate any other reasons why a work based

// on this file might be covered by the GNU General Public License.

// -------------------------------------------

// ####ECOSGPLCOPYRIGHTEND####

//=============================================================================

//#####DESCRIPTIONBEGIN####

//

// Author(s):    gthomas

// Contributors: gthomas, jskov

// Date:         2001-10-30

// Purpose:      Agilent/AAED2000 platform specific support routines

// Description:

// Usage:        #include <cyg/hal/aaed2000.h>

//

//####DESCRIPTIONEND####

//

//===========================================================================*/

//---------------------------------------------------------------------------

// Memory layout details needed by conversion macro

#define AAED2000_SDRAM_PHYS_BASE         0xF0000000

#define AAED2000_SDRAM_VIRT_BASE         0x00000000

#define AAED2000_SDRAM_SIZE              0x02000000

#define AAED2000_SDRAM_MASK              (AAED2000_SDRAM_SIZE-1)

#define AAED2000_FLASH_PHYS_BASE         0x00000000

#define AAED2000_FLASH_VIRT_BASE         0x60000000

#define AAED2000_FLASH_SIZE              0x02000000

#define AAED2000_FLASH_MASK              (AAED2000_FLASH_SIZE-1)

//---------------------------------------------------------------------------

// Clock and state controller

#define AAEC_CSC_BLEOI            0x80000410 // battery low end of interrupt

#define AAEC_CSC_MCEOI            0x80000414 // media changed end of interrupt

#define AAEC_CSC_TEOI             0x80000418 // tick end of interrupt

#define AAEC_CSC_CLKSET           0x80000420

#define AAEC_CSC_CLKSET_PLL       0x80000000

#define AAEC_CSC_CLKSET_SMCROM    0x01000000

#define AAEC_CSC_CLKSET_PS(_n_)       ((_n_)<<18) // values 0-3

#define AAEC_CSC_CLKSET_PCLKDIV(_n_)  ((_n_)<<16) // values 0-3

#define AAEC_CSC_CLKSET_MAINDIV2(_n_) ((_n_)<<11) // values 0-31

#define AAEC_CSC_CLKSET_MAINDIV1(_n_) ((_n_)<<7)  // values 0-15

#define AAEC_CSC_CLKSET_PREDIV(_n_)   ((_n_)<<2)  // values 0-31

#define AAEC_CSC_CLKSET_HCLKDIV(_n_)  ((_n_))     // values 0-3

#define CYGNUM_HAL_ARM_AAED2000_BUS_CLOCK_MHZ ((CYGNUM_HAL_ARM_AAED2000_BUS_CLOCK+500000)/1000000)

#define AAEC_CSC_CLKSET_INIT                                            \

  (  AAEC_CSC_CLKSET_HCLKDIV(CYGNUM_HAL_ARM_AAED2000_CLOCK_HCLKDIV)     \

   | AAEC_CSC_CLKSET_PREDIV(CYGNUM_HAL_ARM_AAED2000_CLOCK_PREDIV)       \

   | AAEC_CSC_CLKSET_MAINDIV1(CYGNUM_HAL_ARM_AAED2000_CLOCK_MAINDIV1)   \

   | AAEC_CSC_CLKSET_MAINDIV2(CYGNUM_HAL_ARM_AAED2000_CLOCK_MAINDIV2)   \

   | AAEC_CSC_CLKSET_PCLKDIV(CYGNUM_HAL_ARM_AAED2000_CLOCK_PCLKDIV)     \

   | AAEC_CSC_CLKSET_PS(CYGNUM_HAL_ARM_AAED2000_CLOCK_PS)               \

   | AAEC_CSC_CLKSET_SMCROM)

//---------------------------------------------------------------------------

// Interrupt controller

#define AAEC_INT_SR               0x80000500

#define AAEC_INT_RSR              0x80000504  // Raw [unmasked] interrupt status

#define AAEC_INT_ENS              0x80000508

#define AAEC_INT_ENC              0x8000050c

#define AAEC_INT_TEST1            0x80000514

#define AAEC_INT_TEST2            0x80000518

#define AAEC_INTS_T3OI            CYGNUM_HAL_INTERRUPT_TC3OI // Timer #3 overflow

//---------------------------------------------------------------------------

// UARTs

#define AAEC_UART1                0x80000600

#define AAEC_UART2                0x80000700

#define AAEC_UART3                0x80000800

#define AAEC_UART2_UMS2EOI        0x80000714 // modem end of interrupt

#define AAEC_UART2_UMS3EOI        0x80000814 // modem end of interrupt

#define AAEC_UART_DATA    0x0000  // Data/FIFO register

#define AAEC_UART_LCR     0x0004  // Control register

#define AAEC_UART_LCR_BRK      0x0001 // Send break

#define AAEC_UART_LCR_PEN      0x0002 // Enable parity

#define AAEC_UART_LCR_EP       0x0004 // Odd/Even parity

#define AAEC_UART_LCR_S2       0x0008 // One/Two stop bits

#define AAEC_UART_LCR_FIFO     0x0010 // Enable FIFO

#define AAEC_UART_LCR_WL5      0x0000 // Word length - 5 bits

#define AAEC_UART_LCR_WL6      0x0020 // Word length - 6 bits

#define AAEC_UART_LCR_WL7      0x0040 // Word length - 7 bits

#define AAEC_UART_LCR_WL8      0x0060 // Word length - 8 bits

#define AAEC_UART_BAUD    0x0008  // Baud rate

#define AAEC_UART_CTRL    0x000C  // Control register

#define AAEC_UART_CTRL_ENAB    0x0001 // Enable uart

#define AAEC_UART_CTRL_SIR     0x0002 // Enable SIR IrDA

#define AAEC_UART_CTRL_SIRLP   0x0004 // Enable low power IrDA

#define AAEC_UART_CTRL_RXP     0x0008 // Receive pin polarity

#define AAEC_UART_CTRL_TXP     0x0010 // Transmit pin polarity

#define AAEC_UART_CTRL_MXP     0x0020 // Modem pin polarity

#define AAEC_UART_CTRL_LOOP    0x0040 // Loopback mode

#define AAEC_UART_CTRL_SIRBD   0x0080 // blanking disable

#define AAEC_UART_STATUS  0x0010  // Status

#define AAEC_UART_STATUS_CTS   0x0001 // Clear-to-send status

#define AAEC_UART_STATUS_DSR   0x0002 // Data-set-ready status

#define AAEC_UART_STATUS_DCD   0x0004 // Data-carrier-detect status

#define AAEC_UART_STATUS_TxBSY 0x0008 // Transmitter busy

#define AAEC_UART_STATUS_RxFE  0x0010 // Receive FIFO empty

#define AAEC_UART_STATUS_TxFF  0x0020 // Transmit FIFO full

#define AAEC_UART_STATUS_RxFF  0x0040 // Receive FIFO full

#define AAEC_UART_STATUS_TxFE  0x0080 // Transmit FIFO empty

#define AAEC_UART_INT     0x0014  // Interrupt status

#define AAEC_UART_INTM    0x0018  // Interrupt mask register

#define AAEC_UART_INTRES  0x001c  // Interrupt result (masked interrupt status)

#define AAEC_UART_INT_RIS      0x0001 // Rx interrupt

#define AAEC_UART_INT_TIS      0x0002 // Tx interrupt

#define AAEC_UART_INT_MIS      0x0004 // Modem status interrupt

#define AAEC_UART_INT_RTIS     0x0008 // Rx timeout interrupt

//#define AAEC_UART_MCTRL   0x0100  // Modem control

//---------------------------------------------------------------------------

// Pump control

#define AAEC_PUMP_CONTROL         0x80000900   // Control

#define AAEC_PUMP_FREQUENCY       0x80000908   // Frequency

//---------------------------------------------------------------------------

// Codec

#define AAEC_COD_CDEOI            0x80000a0c // codec end of interrupt

//---------------------------------------------------------------------------

// Synchronous Serial Peripheral (SSP)

#define AAEC_SSP_CR0              0x80000B00   // Control Register 0

#define AAEC_SSP_CR0_SCR            8            // Serial clock rate - Bits 15..8

#define AAEC_SSP_CR0_SCR_MASK       (0x7F<<AAEC_SSP_CR0_SCR)    

#define AAEC_SSP_CR0_SSE            7            // SSP enable/disable

#define AAEC_SSP_CR0_SSE_MASK       (1<<AAEC_SSP_CR0_SSE)

#define AAEC_SSP_CR0_SSE_ON         1

#define AAEC_SSP_CR0_SSE_OFF        0

#define AAEC_SSP_CR0_FRF            4            // Frame format

#define AAEC_SSP_CR0_FRF_MASK       (0x3<<AAEC_SSP_CR0_FRF)

#define AAEC_SSP_CR0_FRF_MOT        0               // Motorola SPI

#define AAEC_SSP_CR0_FRF_TI         1               // TI synchronous serial frame

#define AAEC_SSP_CR0_FRF_NAT        2               // National microwire

#define AAEC_SSP_CR0_SIZE           0            // Data size

#define AAEC_SSP_CR0_SIZE_MASK      (0xF<<AAEC_SSP_CR0_SIZE)

#define AAEC_SSP_CR1              0x80000B04   // Control Register 1

#define AAEC_SSP_CR1_TXIDLE         7            // Tx idle interrupt

#define AAEC_SSP_CR1_FEN            6            // FIFO enable

#define AAEC_SSP_CR1_RORIE          5            // Rx FIFO overrun interrupt

#define AAEC_SSP_CR1_SPH            4            // SCLK phase

#define AAEC_SSP_CR1_SPO            3            // SCLK polarity

#define AAEC_SSP_CR1_LBM            2            // Lookpback

#define AAEC_SSP_CR1_TIE            1            // Tx interrupt

#define AAEC_SSP_CR1_RIE            0            // Rx Interrupt

#define AAEC_SSP_IIR              0x80000B08   // Interrupt ID register (read)

#define AAEC_SSP_IIR_TXIDLE         7            // Tx idle interrupt

#define AAEC_SSP_IIR_ROR            6            // Rx overrun

#define AAEC_SSP_IIR_TI             1            // Tx FIFO less than half full

#define AAEC_SSP_IIR_RI             0            // Rx FIFO more than half full

#define AAEC_SSP_ICR              0x80000B08   // Interrupt Clear register (write)

#define AAEC_SSP_DR               0x80000B0C   // Data [FIFO] register

#define AAEC_SSP_CPSR             0x80000B10   // Clock prescale

#define AAEC_SSP_SR               0x80000B14   // Status register

#define AAEC_SSP_SR_RFF             8            // Rx FIFO full

#define AAEC_SSP_SR_TFE             7            // Tx FIFO empty

#define AAEC_SSP_SR_ROR             6            // Rx FIFO overrun

#define AAEC_SSP_SR_RHF             5            // Rx FIFO half full

#define AAEC_SSP_SR_THE             4            // Tx FIFO half empty

#define AAEC_SSP_SR_BSY             3            // SSP is busy

#define AAEC_SSP_SR_RNE             2            // Rx FIFO not empty

#define AAEC_SSP_SR_TNF             1            // Tx FIFO not full

//---------------------------------------------------------------------------

// Timer/counter

#define AAEC_TMR_T1_BASE          0x80000C00   // Timer #1 - preload

#define AAEC_TMR_T1LOAD           0x80000C00   // Timer #1 - preload

#define AAEC_TMR_T1VALUE          0x80000C04   // Timer #1 - current value

#define AAEC_TMR_T1CONTROL        0x80000C08   // Timer #1 - control

#define AAEC_TMR_T1EOI            0x80000C0C   // Timer #1 - clear [end] interrupt

#define AAEC_TMR_T2LOAD           0x80000C20   // Timer #2 - preload

#define AAEC_TMR_T2VALUE          0x80000C24   // Timer #2 - current value

#define AAEC_TMR_T2CONTROL        0x80000C28   // Timer #2 - control

#define AAEC_TMR_T2EOI            0x80000C2C   // Timer #2 - clear [end] interrupt

#define AAEC_TMR_BZCONT           0x80000C40

#define AAEC_TMR_T3LOAD           0x80000C80   // Timer #3 - preload

#define AAEC_TMR_T3VALUE          0x80000C84   // Timer #3 - current value

#define AAEC_TMR_T3CONTROL        0x80000C88   // Timer #3 - control

#define AAEC_TMR_T3EOI            0x80000C8C   // Timer #3 - clear [end] interrupt

#define AAEC_TMR_TxLOAD_OFFSET    0

#define AAEC_TMR_TxVALUE_OFFSET   4

#define AAEC_TMR_TxCONTROL_OFFSET 8

#define AAEC_TMR_TxEOI_OFFSET     12

#define AAEC_TMR_TxCONTROL_ENABLE   (1<<7)       // Enable (start) timer

#define AAEC_TMR_TxCONTROL_MODE     (1<<6)       // Operating mode

#define AAEC_TMR_TxCONTROL_MODE_FREE     (0x00&AAEC_TMR_TxCONTROL_MODE)

#define AAEC_TMR_TxCONTROL_MODE_PERIODIC (0xFF&AAEC_TMR_TxCONTROL_MODE)

#define AAEC_TMR_TxCONTROL_CLKSEL   (1<<3)       // Clock select (timer 1,2)

#define AAEC_TMR_TxCONTROL_508KHZ   (1<<3)

#define AAEC_TMR_TxCONTROL_2KHZ     (0<<3)

#define AAEC_TMR_TxCONTROL_508KHZ_uS(_n_) ((_n_)*508000/1000000)

//---------------------------------------------------------------------------

// RTC

#define AAEC_RTC_RTCEOI           0x80000d10   // RTC end of interrupt

//---------------------------------------------------------------------------

// GPIO registers

#define AAEC_PCDR                 0x80000e08

#define AAEC_PBDDR                0x80000e14

#define AAEC_PCCDR                0x80000e18

#define AAEC_KSCAN                0x80000e28

#define AAEC_PINMUX               0x80000e2c

#define AAEC_PFDR                 0x80000e30

#define AAEC_PFDDR                0x80000e34

#define AAEC_GPIO_INT_TYPE1       0x80000e4c

#define AAEC_GPIO_INT_TYPE2       0x80000e50

#define AAEC_GPIO_FEOI            0x80000e54

#define AAEC_GPIO_INTEN           0x80000e58

#define AAEC_GPIO_INT_STATUS      0x80000e5c

#define AAEC_PINMUX_UART3CON      0x00000008

#define AAEC_PINMUX_CODECON       0x00000004

#define AAEC_PINMUX_PD0CON        0x00000002

#define AAEC_PINMUX_PE0CON        0x00000001

//---------------------------------------------------------------------------

// Static memory controller

#define AAEC_SMCBCR0              0x80002000

#define AAEC_SMCBCR1              0x80002004

#define AAEC_SMCBCR2              0x80002008

#define AAEC_SMCBCR3              0x8000200c

#define AAEC_SMCBCR_MW8           0x00000000

#define AAEC_SMCBCR_MW16          0x10000000

#define AAEC_SMCBCR_MW32          0x30000000

#define AAEC_SMCBCR_PME           0x08000000

#define AAEC_SMCBCR_WP            0x04000000

#define AAEC_SMCBCR_WPERR         0x02000000

#define AAEC_SMCBCR_WST(_n_)      (((((_n_)-1)&0x1f)<<11) | ((((_n_)-1)&0x1f)<<5)) // for n 1-32

#define AAEC_SMCBCR_IDCY(_n_)     ((((_n_)-1)&0x0f)<<0)  // for n 1-16

// These settings come from the Agilent startup.s file

// [note, the WST values match their values, not the comments]

// CS0: Flash, access=90ns, hold=30ns

// CS1: ethernet, access=162ns, hold=47ns

// CS2: GPIO, access=14ns, hold=14ns

#if (75 == CYGNUM_HAL_ARM_AAED2000_BUS_CLOCK_MHZ)

# define _CS0_WST   8

# define _CS0_IDCY  3

# define _CS1_WST  14

# define _CS1_IDCY  4

# define _CS3_WST   3

# define _CS3_IDCY  2

#elif (83 == CYGNUM_HAL_ARM_AAED2000_BUS_CLOCK_MHZ)

# define _CS0_WST   9

# define _CS0_IDCY  3

# define _CS1_WST  15

# define _CS1_IDCY  4

# define _CS3_WST   3

# define _CS3_IDCY  2

#else

# error "Unsupported clocking"

#endif

//---------------------------------------------------------------------------

// Synchronous memory controller

#define AAEC_SMC_GLOBAL           0x80002404

#define AAEC_SMC_REFRESH_TIME     0x80002408

#define AAEC_SMC_BOOT_STATUS      0x8000240c

#define AAEC_SMC_DEV0             0x80002410

#define AAEC_SMC_DEV1             0x80002414

#define AAEC_SMC_DEV2             0x80002418

#define AAEC_SMC_DEV3             0x8000241c

#define AAEC_SMC_GLOBAL_CKE       0x80000000

#define AAEC_SMC_GLOBAL_CS        0x40000000

#define AAEC_SMC_GLOBAL_LCR       0x00000040

#define AAEC_SMC_GLOBAL_BUSY      0x00000020

#define AAEC_SMC_GLOBAL_MRS       0x00000002

#define AAEC_SMC_GLOBAL_INIT      0x00000001

#define AAEC_SMC_GLOBAL_CMD_NOP    (AAEC_SMC_GLOBAL_INIT|AAEC_SMC_GLOBAL_MRS)

#define AAEC_SMC_GLOBAL_CMD_PREALL (AAEC_SMC_GLOBAL_INIT)

#define AAEC_SMC_GLOBAL_CMD_MODE   (AAEC_SMC_GLOBAL_MRS)

#define AAEC_SMC_GLOBAL_CMD_ENABLE (AAEC_SMC_GLOBAL_CKE)

#define AAEC_SMC_DEV_AUTOP        0x01000000

#define AAEC_SMC_DEV_RAS_2        0x00200000

#define AAEC_SMC_DEV_RAS_3        0x00300000

#define AAEC_SMC_DEV_WBL_4        0x00080000

#define AAEC_SMC_DEV_WBL_1        0x00000000

#define AAEC_SMC_DEV_CASLAT(_n_)  (((_n_)-1)<<16) // 2-7

#define AAEC_SMC_DEV_2KPAGE       0x00000040

#define AAEC_SMC_DEV_SROMLL       0x00000020

#define AAEC_SMC_DEV_SROM512      0x00000010

#define AAEC_SMC_DEV_BANKS_2      0x00000008

#define AAEC_SMC_DEV_BANKS_4      0x00000000

#define AAEC_SMC_DEV_WIDTH16      0x00000004

#define AAEC_SMC_DEV_WIDTH32      0x00000000

#define AAEC_SMC_DEV_INIT         ( AAEC_SMC_DEV_RAS_2 \

                                   |AAEC_SMC_DEV_CASLAT(3) \

                                   |AAEC_SMC_DEV_BANKS_2)

//---------------------------------------------------------------------------

// LCD controller

#define AAEC_LCD_TIMING0          0x80003000   // Timing registers

#define AAEC_LCD_TIMING1          0x80003004

#define AAEC_LCD_TIMING2          0x80003008

#define AAEC_LCD_TIMING3          0x8000300C

#define AAEC_LCD_UPBASE           0x80003010   // Upper panel DMA address

#define AAEC_LCD_LPBASE           0x80003014   // Lower panel DMA address

#define AAEC_LCD_MASK             0x80003018   // Status mask

#define AAEC_LCD_CONTROL          0x8000301C   // Control

#define AAEC_LCD_CONTROL_ENAB       0x00000001    // Enable controller

#define AAEC_LCD_CONTROL_PWR_ENAB   0x00000800    // Enables signals

#define AAEC_LCD_STATUS           0x80003020   // Status

#define AAEC_LCD_INTERRUPT        0x80003024   // Interrupts

#define AAEC_LCD_UPCURR           0x80003028   // Upper panel current address

#define AAEC_LCD_LPCURR           0x8000302C   // Lower panel current address

#define AAEC_LCD_LPOVERFLOW       0x80003030   // Panel overflow 

#define AAEC_LCD_PALETTE          0x80003200   // Palette

//---------------------------------------------------------------------------

// Extended GPIO bits [platform specific]

#define AAED_EXT_GPIO             0x30000000

#define AAED_EXT_GPIO_KBD_SCAN      0x00003FFF // Keyboard scan data

#define AAED_EXT_GPIO_PWR_INT       0x00008FFF // Smart battery charger interrupt

#define AAED_EXT_GPIO_SWITCHES      0x000F0000 // DIP switches

#define AAED_EXT_GPIO_SWITCHES_SHIFT 16

#define AAED_EXT_GPIO_USB_VBUS      0x00400000 // USB Vbus sense

#define AAED_EXT_GPIO_LCD_PWR_EN    0x02000000 // LCD (& backlight) power enable

#define AAED_EXT_GPIO_LED0          0x20000000 // LED 0 (0=>ON, 1=>OFF)

#define AAED_EXT_GPIO_LED1          0x40000000 // LED 1 (0=>ON, 1=>OFF)

#define AAED_EXT_GPIO_LED2          0x80000000 // LED 2 (0=>ON, 1=>OFF)

/*---------------------------------------------------------------------------*/

/* end of aaed2000.h                                                          */

#endif /* CYGONCE_AAED2000_H */