Subversion Repositories openrisc

/* ----------------------------------------------------------------------------

 *         ATMEL Microcontroller Software Support

 * ----------------------------------------------------------------------------

 * Copyright (c) 2008, Atmel Corporation

 *

 * All rights reserved.

 *

 * Redistribution and use in source and binary forms, with or without

 * modification, are permitted provided that the following conditions are met:

 *

 * - Redistributions of source code must retain the above copyright notice,

 * this list of conditions and the disclaimer below.

 *

 * Atmel's name may not be used to endorse or promote products derived from

 * this software without specific prior written permission.

 *

 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR

 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE

 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,

 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,

 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

 * ----------------------------------------------------------------------------

 */

//------------------------------------------------------------------------------

/// \dir

/// !Purpose

/// 

/// This module provides several definitions and methods for using an USART

/// peripheral.

///

/// !Usage

/// -# Enable the USART peripheral clock in the PMC.

/// -# Enable the required USART PIOs (see pio.h).

/// -# Configure the UART by calling USART_Configure.

/// -# Enable the transmitter and/or the receiver of the USART using

///    USART_SetTransmitterEnabled and USART_SetReceiverEnabled.

/// -# Send data through the USART using the USART_Write and

///    USART_WriteBuffer methods.

/// -# Receive data from the USART using the USART_Read and

///    USART_ReadBuffer functions; the availability of data can be polled

///    with USART_IsDataAvailable.

/// -# Disable the transmitter and/or the receiver of the USART with

///    USART_SetTransmitterEnabled and USART_SetReceiverEnabled.

//------------------------------------------------------------------------------

#ifndef USART_H

#define USART_H

//------------------------------------------------------------------------------

//         Headers

//------------------------------------------------------------------------------

#include <board.h>

//------------------------------------------------------------------------------

//         Definitions

//------------------------------------------------------------------------------

//------------------------------------------------------------------------------

/// \page "USART modes"

/// This page lists several common operating modes for an USART peripheral.

/// 

/// !Modes

/// - USART_MODE_ASYNCHRONOUS

/// - USART_MODE_IRDA

/// Basic asynchronous mode, i.e. 8 bits no parity.

#define USART_MODE_ASYNCHRONOUS (AT91C_US_CHRL_8_BITS | AT91C_US_PAR_NONE)

/// IRDA mode

#define USART_MODE_IRDA         (AT91C_US_USMODE_IRDA | AT91C_US_CHRL_8_BITS | AT91C_US_PAR_NONE | AT91C_US_FILTER)

//------------------------------------------------------------------------------

//------------------------------------------------------------------------------

//         Exported functions

//------------------------------------------------------------------------------

extern void USART_Configure(

    AT91S_USART *usart,

    unsigned int mode,

    unsigned int baudrate,

    unsigned int masterClock);

extern void USART_SetTransmitterEnabled(AT91S_USART *usart, unsigned char enabled);

extern void USART_SetReceiverEnabled(AT91S_USART *usart, unsigned char enabled);

extern void USART_Write(

    AT91S_USART *usart,

    unsigned short data,

    volatile unsigned int timeOut);

extern unsigned char USART_WriteBuffer(

    AT91S_USART *usart,

    void *buffer,

    unsigned int size);

extern unsigned short USART_Read(

    AT91S_USART *usart,

    volatile unsigned int timeOut);

extern unsigned char USART_ReadBuffer(

    AT91S_USART *usart,

    void *buffer,

    unsigned int size);

extern unsigned char USART_IsDataAvailable(AT91S_USART *usart);

extern void USART_SetIrdaFilter(AT91S_USART *pUsart, unsigned char filter);

#endif //#ifndef USART_H