Subversion Repositories openrisc

/* ----------------------------------------------------------------------------

 *         ATMEL Microcontroller Software Support

 * ----------------------------------------------------------------------------

 * Copyright (c) 2008, Atmel Corporation

 *

 * All rights reserved.

 *

 * Redistribution and use in source and binary forms, with or without

 * modification, are permitted provided that the following conditions are met:

 *

 * - Redistributions of source code must retain the above copyright notice,

 * this list of conditions and the disclaimer below.

 *

 * Atmel's name may not be used to endorse or promote products derived from

 * this software without specific prior written permission.

 *

 * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR

 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE

 * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,

 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT

 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,

 * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,

 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

 * ----------------------------------------------------------------------------

 */

//------------------------------------------------------------------------------

//         Headers

//------------------------------------------------------------------------------

#include "pmc.h"

#include <board.h>

#include <utility/assert.h>

#include <utility/trace.h>

//------------------------------------------------------------------------------

//         Global functions

//------------------------------------------------------------------------------

#if defined(at91sam7l64) || defined(at91sam7l128)

//------------------------------------------------------------------------------

/// Sets the fast wake-up inputs that can get the device out of Wait mode.

/// \param inputs  Fast wake-up inputs to enable.

//------------------------------------------------------------------------------

void PMC_SetFastWakeUpInputs(unsigned int inputs)

{

    SANITY_CHECK((inputs & ~0xFF) == 0);

    AT91C_BASE_PMC->PMC_FSMR = inputs;

}

#if !defined(__ICCARM__)

__attribute__ ((section (".ramfunc"))) // GCC

#endif

//------------------------------------------------------------------------------

/// Disables the main oscillator, making the device enter Wait mode.

//------------------------------------------------------------------------------

void PMC_DisableMainOscillatorForWaitMode(void)

{

    AT91C_BASE_PMC->PMC_MOR = 0x37 << 16;

    while ((AT91C_BASE_PMC->PMC_MOR & AT91C_PMC_MAINSELS) != AT91C_PMC_MAINSELS);

}

#endif

#if defined(at91sam7l)

//------------------------------------------------------------------------------

/// Disables the main oscillator when NOT running on it.

//------------------------------------------------------------------------------

void PMC_DisableMainOscillator(void)

{

    AT91C_BASE_PMC->PMC_MOR = 0x37 << 16;

    while ((AT91C_BASE_PMC->PMC_SR & AT91C_PMC_MAINSELS) == AT91C_PMC_MAINSELS);

}

#endif

//------------------------------------------------------------------------------

/// Disables the processor clock, making the device enter Idle mode.

//------------------------------------------------------------------------------

void PMC_DisableProcessorClock(void)

{

    AT91C_BASE_PMC->PMC_SCDR = AT91C_PMC_PCK;

    while ((AT91C_BASE_PMC->PMC_SCSR & AT91C_PMC_PCK) != AT91C_PMC_PCK);

}

//------------------------------------------------------------------------------

/// Enables the clock of a peripheral. The peripheral ID (AT91C_ID_xxx) is used

/// to identify which peripheral is targetted.

/// Note that the ID must NOT be shifted (i.e. 1 << AT91C_ID_xxx).

/// \param id  Peripheral ID (AT91C_ID_xxx).

//------------------------------------------------------------------------------

void PMC_EnablePeripheral(unsigned int id)

{

    SANITY_CHECK(id < 32);

    if ((AT91C_BASE_PMC->PMC_PCSR & (1 << id)) == (1 << id)) {

        trace_LOG(trace_INFO,

                  "-I- PMC_EnablePeripheral: clock of peripheral"

                  " %u is already enabled\n\r",

                  id);

    }

    else {

        AT91C_BASE_PMC->PMC_PCER = 1 << id;

    }

}

//------------------------------------------------------------------------------

/// Disables the clock of a peripheral. The peripheral ID (AT91C_ID_xxx) is used

/// to identify which peripheral is targetted.

/// Note that the ID must NOT be shifted (i.e. 1 << AT91C_ID_xxx).

/// \param id  Peripheral ID (AT91C_ID_xxx).

//------------------------------------------------------------------------------

void PMC_DisablePeripheral(unsigned int id)

{

    SANITY_CHECK(id < 32);

    if ((AT91C_BASE_PMC->PMC_PCSR & (1 << id)) != (1 << id)) {

        trace_LOG(trace_INFO,

                  "-I- PMC_DisablePeripheral: clock of peripheral"

                  " %u is not enabled\n\r",

                  id);

    }

    else {

        AT91C_BASE_PMC->PMC_PCDR = 1 << id;

    }

}