URL https://opencores.org/ocsvn/openrisc/openrisc/trunk

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [MicroBlaze/] [system.mhs] - Blame information for rev 745

Go to most recent revision | Details | Compare with Previous | View Log


# ##############################################################################
# Created by Base System Builder Wizard for Xilinx EDK 7.1.2 Build EDK_H.12.5.1
# Sun Nov 13 16:46:19 2005
# Target Board:  Xilinx Virtex 4 ML403 Evaluation Platform Rev 1
# Family:        virtex4
# Device:        xc4vfx12
# Package:       ff668
# Speed Grade:   -10
# Processor: Microblaze
# System clock frequency: 100.000000 MHz
# Debug interface: On-Chip HW Debug Module
# On Chip Memory :  64 KB
# ##############################################################################
 
 
 PARAMETER VERSION = 2.1.0
 
 
 PORT fpga_0_RS232_Uart_RX_pin = fpga_0_RS232_Uart_RX, DIR = INPUT
 PORT fpga_0_RS232_Uart_TX_pin = fpga_0_RS232_Uart_TX, DIR = OUTPUT
 PORT fpga_0_LEDs_4Bit_GPIO_IO_pin = fpga_0_LEDs_4Bit_GPIO_IO, DIR = INOUT, VEC = [0:3]
 PORT fpga_0_LEDs_Positions_GPIO_IO_pin = fpga_0_LEDs_Positions_GPIO_IO, DIR = INOUT, VEC = [0:4]
 PORT sys_clk_pin = dcm_clk_s, DIR = INPUT, SIGIS = DCMCLK
 PORT sys_rst_pin = sys_rst_s, DIR = INPUT
 
 
BEGIN microblaze
 PARAMETER INSTANCE = microblaze_0
 PARAMETER HW_VER = 4.00.a
 PARAMETER C_DEBUG_ENABLED = 1
 PARAMETER C_NUMBER_OF_PC_BRK = 2
 PARAMETER C_NUMBER_OF_RD_ADDR_BRK = 1
 PARAMETER C_NUMBER_OF_WR_ADDR_BRK = 1
 BUS_INTERFACE DLMB = dlmb
 BUS_INTERFACE ILMB = ilmb
 BUS_INTERFACE DOPB = mb_opb
 BUS_INTERFACE IOPB = mb_opb
 PORT CLK = sys_clk_s
 PORT DBG_CAPTURE = DBG_CAPTURE_s
 PORT DBG_CLK = DBG_CLK_s
 PORT DBG_REG_EN = DBG_REG_EN_s
 PORT DBG_TDI = DBG_TDI_s
 PORT DBG_TDO = DBG_TDO_s
 PORT DBG_UPDATE = DBG_UPDATE_s
 PORT Interrupt = Interrupt
END
 
BEGIN opb_v20
 PARAMETER INSTANCE = mb_opb
 PARAMETER HW_VER = 1.10.c
 PARAMETER C_EXT_RESET_HIGH = 0
 PORT SYS_Rst = sys_rst_s
 PORT OPB_Clk = sys_clk_s
END
 
BEGIN opb_mdm
 PARAMETER INSTANCE = debug_module
 PARAMETER HW_VER = 2.00.a
 PARAMETER C_MB_DBG_PORTS = 1
 PARAMETER C_USE_UART = 1
 PARAMETER C_UART_WIDTH = 8
 PARAMETER C_BASEADDR = 0x41400000
 PARAMETER C_HIGHADDR = 0x4140ffff
 BUS_INTERFACE SOPB = mb_opb
 PORT OPB_Clk = sys_clk_s
 PORT DBG_CAPTURE_0 = DBG_CAPTURE_s
 PORT DBG_CLK_0 = DBG_CLK_s
 PORT DBG_REG_EN_0 = DBG_REG_EN_s
 PORT DBG_TDI_0 = DBG_TDI_s
 PORT DBG_TDO_0 = DBG_TDO_s
 PORT DBG_UPDATE_0 = DBG_UPDATE_s
END
 
BEGIN lmb_v10
 PARAMETER INSTANCE = ilmb
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_EXT_RESET_HIGH = 0
 PORT SYS_Rst = sys_rst_s
 PORT LMB_Clk = sys_clk_s
END
 
BEGIN lmb_v10
 PARAMETER INSTANCE = dlmb
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_EXT_RESET_HIGH = 0
 PORT SYS_Rst = sys_rst_s
 PORT LMB_Clk = sys_clk_s
END
 
BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = dlmb_cntlr
 PARAMETER HW_VER = 1.00.b
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x0000ffff
 BUS_INTERFACE SLMB = dlmb
 BUS_INTERFACE BRAM_PORT = dlmb_port
END
 
BEGIN lmb_bram_if_cntlr
 PARAMETER INSTANCE = ilmb_cntlr
 PARAMETER HW_VER = 1.00.b
 PARAMETER C_BASEADDR = 0x00000000
 PARAMETER C_HIGHADDR = 0x0000ffff
 BUS_INTERFACE SLMB = ilmb
 BUS_INTERFACE BRAM_PORT = ilmb_port
END
 
BEGIN bram_block
 PARAMETER INSTANCE = lmb_bram
 PARAMETER HW_VER = 1.00.a
 BUS_INTERFACE PORTA = ilmb_port
 BUS_INTERFACE PORTB = dlmb_port
END
 
BEGIN opb_uartlite
 PARAMETER INSTANCE = RS232_Uart
 PARAMETER HW_VER = 1.00.b
 PARAMETER C_BAUDRATE = 9600
 PARAMETER C_DATA_BITS = 8
 PARAMETER C_ODD_PARITY = 0
 PARAMETER C_USE_PARITY = 0
 PARAMETER C_CLK_FREQ = 100000000
 PARAMETER C_BASEADDR = 0x40600000
 PARAMETER C_HIGHADDR = 0x4060ffff
 BUS_INTERFACE SOPB = mb_opb
 PORT OPB_Clk = sys_clk_s
 PORT Interrupt = RS232_Uart_Interrupt
 PORT RX = fpga_0_RS232_Uart_RX
 PORT TX = fpga_0_RS232_Uart_TX
END
 
BEGIN opb_gpio
 PARAMETER INSTANCE = LEDs_4Bit
 PARAMETER HW_VER = 3.01.b
 PARAMETER C_GPIO_WIDTH = 4
 PARAMETER C_IS_DUAL = 0
 PARAMETER C_IS_BIDIR = 1
 PARAMETER C_ALL_INPUTS = 0
 PARAMETER C_BASEADDR = 0x40020000
 PARAMETER C_HIGHADDR = 0x4002ffff
 BUS_INTERFACE SOPB = mb_opb
 PORT OPB_Clk = sys_clk_s
 PORT GPIO_IO = fpga_0_LEDs_4Bit_GPIO_IO
END
 
BEGIN opb_gpio
 PARAMETER INSTANCE = LEDs_Positions
 PARAMETER HW_VER = 3.01.b
 PARAMETER C_GPIO_WIDTH = 5
 PARAMETER C_IS_DUAL = 0
 PARAMETER C_IS_BIDIR = 1
 PARAMETER C_ALL_INPUTS = 0
 PARAMETER C_BASEADDR = 0x40000000
 PARAMETER C_HIGHADDR = 0x4000ffff
 BUS_INTERFACE SOPB = mb_opb
 PORT OPB_Clk = sys_clk_s
 PORT GPIO_IO = fpga_0_LEDs_Positions_GPIO_IO
END
 
BEGIN opb_timer
 PARAMETER INSTANCE = opb_timer_1
 PARAMETER HW_VER = 1.00.b
 PARAMETER C_COUNT_WIDTH = 32
 PARAMETER C_ONE_TIMER_ONLY = 1
 PARAMETER C_BASEADDR = 0x41c00000
 PARAMETER C_HIGHADDR = 0x41c0ffff
 BUS_INTERFACE SOPB = mb_opb
 PORT OPB_Clk = sys_clk_s
 PORT Interrupt = opb_timer_1_Interrupt
END
 
BEGIN opb_intc
 PARAMETER INSTANCE = opb_intc_0
 PARAMETER HW_VER = 1.00.c
 PARAMETER C_BASEADDR = 0x41200000
 PARAMETER C_HIGHADDR = 0x4120ffff
 PARAMETER C_HAS_IPR = 0
 BUS_INTERFACE SOPB = mb_opb
 PORT Irq = Interrupt
 PORT Intr = RS232_Uart_Interrupt & opb_timer_1_Interrupt
END
 
BEGIN dcm_module
 PARAMETER INSTANCE = dcm_0
 PARAMETER HW_VER = 1.00.a
 PARAMETER C_CLK0_BUF = TRUE
 PARAMETER C_CLKIN_PERIOD = 10.000000
 PARAMETER C_CLK_FEEDBACK = 1X
 PARAMETER C_EXT_RESET_HIGH = 1
 PORT CLKIN = dcm_clk_s
 PORT CLK0 = sys_clk_s
 PORT CLKFB = sys_clk_s
 PORT RST = net_gnd
 PORT LOCKED = dcm_0_lock
END
 

Line No.	Rev	Author	Line
1	584	jeremybenn	`# ##############################################################################`
2			`# Created by Base System Builder Wizard for Xilinx EDK 7.1.2 Build EDK_H.12.5.1`
3			`# Sun Nov 13 16:46:19 2005`
4			`# Target Board: Xilinx Virtex 4 ML403 Evaluation Platform Rev 1`
5			`# Family: virtex4`
6			`# Device: xc4vfx12`
7			`# Package: ff668`
8			`# Speed Grade: -10`
9			`# Processor: Microblaze`
10			`# System clock frequency: 100.000000 MHz`
11			`# Debug interface: On-Chip HW Debug Module`
12			`# On Chip Memory : 64 KB`
13			`# ##############################################################################`
14
15
16			`PARAMETER VERSION = 2.1.0`
17
18
19			`PORT fpga_0_RS232_Uart_RX_pin = fpga_0_RS232_Uart_RX, DIR = INPUT`
20			`PORT fpga_0_RS232_Uart_TX_pin = fpga_0_RS232_Uart_TX, DIR = OUTPUT`
21			`PORT fpga_0_LEDs_4Bit_GPIO_IO_pin = fpga_0_LEDs_4Bit_GPIO_IO, DIR = INOUT, VEC = [0:3]`
22			`PORT fpga_0_LEDs_Positions_GPIO_IO_pin = fpga_0_LEDs_Positions_GPIO_IO, DIR = INOUT, VEC = [0:4]`
23			`PORT sys_clk_pin = dcm_clk_s, DIR = INPUT, SIGIS = DCMCLK`
24			`PORT sys_rst_pin = sys_rst_s, DIR = INPUT`
25
26
27			`BEGIN microblaze`
28			`PARAMETER INSTANCE = microblaze_0`
29			`PARAMETER HW_VER = 4.00.a`
30			`PARAMETER C_DEBUG_ENABLED = 1`
31			`PARAMETER C_NUMBER_OF_PC_BRK = 2`
32			`PARAMETER C_NUMBER_OF_RD_ADDR_BRK = 1`
33			`PARAMETER C_NUMBER_OF_WR_ADDR_BRK = 1`
34			`BUS_INTERFACE DLMB = dlmb`
35			`BUS_INTERFACE ILMB = ilmb`
36			`BUS_INTERFACE DOPB = mb_opb`
37			`BUS_INTERFACE IOPB = mb_opb`
38			`PORT CLK = sys_clk_s`
39			`PORT DBG_CAPTURE = DBG_CAPTURE_s`
40			`PORT DBG_CLK = DBG_CLK_s`
41			`PORT DBG_REG_EN = DBG_REG_EN_s`
42			`PORT DBG_TDI = DBG_TDI_s`
43			`PORT DBG_TDO = DBG_TDO_s`
44			`PORT DBG_UPDATE = DBG_UPDATE_s`
45			`PORT Interrupt = Interrupt`
46			`END`
47
48			`BEGIN opb_v20`
49			`PARAMETER INSTANCE = mb_opb`
50			`PARAMETER HW_VER = 1.10.c`
51			`PARAMETER C_EXT_RESET_HIGH = 0`
52			`PORT SYS_Rst = sys_rst_s`
53			`PORT OPB_Clk = sys_clk_s`
54			`END`
55
56			`BEGIN opb_mdm`
57			`PARAMETER INSTANCE = debug_module`
58			`PARAMETER HW_VER = 2.00.a`
59			`PARAMETER C_MB_DBG_PORTS = 1`
60			`PARAMETER C_USE_UART = 1`
61			`PARAMETER C_UART_WIDTH = 8`
62			`PARAMETER C_BASEADDR = 0x41400000`
63			`PARAMETER C_HIGHADDR = 0x4140ffff`
64			`BUS_INTERFACE SOPB = mb_opb`
65			`PORT OPB_Clk = sys_clk_s`
66			`PORT DBG_CAPTURE_0 = DBG_CAPTURE_s`
67			`PORT DBG_CLK_0 = DBG_CLK_s`
68			`PORT DBG_REG_EN_0 = DBG_REG_EN_s`
69			`PORT DBG_TDI_0 = DBG_TDI_s`
70			`PORT DBG_TDO_0 = DBG_TDO_s`
71			`PORT DBG_UPDATE_0 = DBG_UPDATE_s`
72			`END`
73
74			`BEGIN lmb_v10`
75			`PARAMETER INSTANCE = ilmb`
76			`PARAMETER HW_VER = 1.00.a`
77			`PARAMETER C_EXT_RESET_HIGH = 0`
78			`PORT SYS_Rst = sys_rst_s`
79			`PORT LMB_Clk = sys_clk_s`
80			`END`
81
82			`BEGIN lmb_v10`
83			`PARAMETER INSTANCE = dlmb`
84			`PARAMETER HW_VER = 1.00.a`
85			`PARAMETER C_EXT_RESET_HIGH = 0`
86			`PORT SYS_Rst = sys_rst_s`
87			`PORT LMB_Clk = sys_clk_s`
88			`END`
89
90			`BEGIN lmb_bram_if_cntlr`
91			`PARAMETER INSTANCE = dlmb_cntlr`
92			`PARAMETER HW_VER = 1.00.b`
93			`PARAMETER C_BASEADDR = 0x00000000`
94			`PARAMETER C_HIGHADDR = 0x0000ffff`
95			`BUS_INTERFACE SLMB = dlmb`
96			`BUS_INTERFACE BRAM_PORT = dlmb_port`
97			`END`
98
99			`BEGIN lmb_bram_if_cntlr`
100			`PARAMETER INSTANCE = ilmb_cntlr`
101			`PARAMETER HW_VER = 1.00.b`
102			`PARAMETER C_BASEADDR = 0x00000000`
103			`PARAMETER C_HIGHADDR = 0x0000ffff`
104			`BUS_INTERFACE SLMB = ilmb`
105			`BUS_INTERFACE BRAM_PORT = ilmb_port`
106			`END`
107
108			`BEGIN bram_block`
109			`PARAMETER INSTANCE = lmb_bram`
110			`PARAMETER HW_VER = 1.00.a`
111			`BUS_INTERFACE PORTA = ilmb_port`
112			`BUS_INTERFACE PORTB = dlmb_port`
113			`END`
114
115			`BEGIN opb_uartlite`
116			`PARAMETER INSTANCE = RS232_Uart`
117			`PARAMETER HW_VER = 1.00.b`
118			`PARAMETER C_BAUDRATE = 9600`
119			`PARAMETER C_DATA_BITS = 8`
120			`PARAMETER C_ODD_PARITY = 0`
121			`PARAMETER C_USE_PARITY = 0`
122			`PARAMETER C_CLK_FREQ = 100000000`
123			`PARAMETER C_BASEADDR = 0x40600000`
124			`PARAMETER C_HIGHADDR = 0x4060ffff`
125			`BUS_INTERFACE SOPB = mb_opb`
126			`PORT OPB_Clk = sys_clk_s`
127			`PORT Interrupt = RS232_Uart_Interrupt`
128			`PORT RX = fpga_0_RS232_Uart_RX`
129			`PORT TX = fpga_0_RS232_Uart_TX`
130			`END`
131
132			`BEGIN opb_gpio`
133			`PARAMETER INSTANCE = LEDs_4Bit`
134			`PARAMETER HW_VER = 3.01.b`
135			`PARAMETER C_GPIO_WIDTH = 4`
136			`PARAMETER C_IS_DUAL = 0`
137			`PARAMETER C_IS_BIDIR = 1`
138			`PARAMETER C_ALL_INPUTS = 0`
139			`PARAMETER C_BASEADDR = 0x40020000`
140			`PARAMETER C_HIGHADDR = 0x4002ffff`
141			`BUS_INTERFACE SOPB = mb_opb`
142			`PORT OPB_Clk = sys_clk_s`
143			`PORT GPIO_IO = fpga_0_LEDs_4Bit_GPIO_IO`
144			`END`
145
146			`BEGIN opb_gpio`
147			`PARAMETER INSTANCE = LEDs_Positions`
148			`PARAMETER HW_VER = 3.01.b`
149			`PARAMETER C_GPIO_WIDTH = 5`
150			`PARAMETER C_IS_DUAL = 0`
151			`PARAMETER C_IS_BIDIR = 1`
152			`PARAMETER C_ALL_INPUTS = 0`
153			`PARAMETER C_BASEADDR = 0x40000000`
154			`PARAMETER C_HIGHADDR = 0x4000ffff`
155			`BUS_INTERFACE SOPB = mb_opb`
156			`PORT OPB_Clk = sys_clk_s`
157			`PORT GPIO_IO = fpga_0_LEDs_Positions_GPIO_IO`
158			`END`
159
160			`BEGIN opb_timer`
161			`PARAMETER INSTANCE = opb_timer_1`
162			`PARAMETER HW_VER = 1.00.b`
163			`PARAMETER C_COUNT_WIDTH = 32`
164			`PARAMETER C_ONE_TIMER_ONLY = 1`
165			`PARAMETER C_BASEADDR = 0x41c00000`
166			`PARAMETER C_HIGHADDR = 0x41c0ffff`
167			`BUS_INTERFACE SOPB = mb_opb`
168			`PORT OPB_Clk = sys_clk_s`
169			`PORT Interrupt = opb_timer_1_Interrupt`
170			`END`
171
172			`BEGIN opb_intc`
173			`PARAMETER INSTANCE = opb_intc_0`
174			`PARAMETER HW_VER = 1.00.c`
175			`PARAMETER C_BASEADDR = 0x41200000`
176			`PARAMETER C_HIGHADDR = 0x4120ffff`
177			`PARAMETER C_HAS_IPR = 0`
178			`BUS_INTERFACE SOPB = mb_opb`
179			`PORT Irq = Interrupt`
180			`PORT Intr = RS232_Uart_Interrupt & opb_timer_1_Interrupt`
181			`END`
182
183			`BEGIN dcm_module`
184			`PARAMETER INSTANCE = dcm_0`
185			`PARAMETER HW_VER = 1.00.a`
186			`PARAMETER C_CLK0_BUF = TRUE`
187			`PARAMETER C_CLKIN_PERIOD = 10.000000`
188			`PARAMETER C_CLK_FEEDBACK = 1X`
189			`PARAMETER C_EXT_RESET_HIGH = 1`
190			`PORT CLKIN = dcm_clk_s`
191			`PORT CLK0 = sys_clk_s`
192			`PORT CLKFB = sys_clk_s`
193			`PORT RST = net_gnd`
194			`PORT LOCKED = dcm_0_lock`
195			`END`
196

Browse

Tools

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [rtos/] [freertos-6.1.1/] [Demo/] [MicroBlaze/] [system.mhs] - Blame information for rev 745