Subversion Repositories openrisc

/*

 *  $Id: serial.c,v 1.2 2001-09-27 11:59:36 chris Exp $

 */

#include "serial.h"

#include "rtems.h"

typedef unsigned char uchar ;           /* Abbreviations */

typedef unsigned short ushort ;

typedef unsigned long ulong ;

#if 0

#define BAUDRate        9600            /* Fixed Uart baud rate */

#endif

#define SEND_WAIT       0x0100          /* Waiting to send character */

#define TDR(i)

/********************************************************************

 ***  16552 specific DUART definitions.

 *******************************************************************/

typedef struct uart_16552 DUART ;

#ifndef notdef

struct uart_16552

{

        short   u_short[8*2] ;

} ;

#define u_reg(n)        u_short[2*(n)]

#else

struct uart_16552

{

        int     u_int[8] ;

} ;

#define u_reg(n)        u_int[(n)]

#endif

#define u_tdr           u_reg(0)        /* Transmit Data Register (write) */

#define u_rdr           u_reg(0)        /* Receive Data Register (read) */

#define u_dlr0          u_reg(0)        /* Divisor Latch Register (lsb) */

#define u_ier           u_reg(1)        /* Interrupt Enable Register */

#define u_dlr1          u_reg(1)        /* Divisor Latch Register (msb) */

#define u_iir           u_reg(2)        /* Interrupt ID Register (read) */

#define u_fcr           u_reg(2)        /* FIFO Control Register (write) */

#define u_afr           u_reg(2)        /* Alternate Funct Reg (read/write) */

#define u_lcr           u_reg(3)        /* Line Control Register */

#define u_mcr           u_reg(4)        /* Modem Control Register */

#define u_lsr           u_reg(5)        /* Line Status Register */

#define u_msr           u_reg(6)        /* Modem Status Register */

#define u_spr           u_reg(7)        /* Scratch Pad Register */

#define uart1   ((volatile DUART *)0x90000380)

#define uart2   ((volatile DUART *)0x90000300)

#define NUM_UARTS 2

static volatile DUART * duart[NUM_UARTS] = { uart1, uart2 };

extern void     display_msg(void);

/*extern int    sprintf();*/

#define board_rev_reg  ((volatile short *)0x90000080)

static unsigned int shift_val = 0;

/***********************************************************************

 ***  16552 DUART initialization routine.

 ***********************************************************************/

int

console_duartinit(unsigned int uart_num, unsigned int BAUDRate)

{

        register uchar  tmp;

        unsigned int board_rev = *board_rev_reg & 0xff;

        switch( BAUDRate )

        {

           case 1200:

           case 2400:

           case 9600:

           case 19200:

           case 38400:

           case 57600:

              break;

           default:

              /* unknown baud rate */

              return FALSE;

        }

        /* the board rev register should never be 0xff.

           if it equals 0xff, assume that we're on old hardware

           that needs all values shifted by 8. */

        if ( board_rev == 0xff )

           shift_val = 8;

        else

           shift_val = 0;

        if ( uart_num >= NUM_UARTS )

           return -1;

        duart[uart_num]->u_lcr = 0x80<<shift_val ;      /* Set DLAB bit to 1 */

        duart[uart_num]->u_dlr0 = ((115200 / BAUDRate) >> 0)<<shift_val ; /* Set baud               */

        duart[uart_num]->u_dlr1 = ((115200 / BAUDRate) >> 8)<<shift_val ; /*          rate         */

        duart[uart_num]->u_lcr = 0x03<<shift_val ;      /* 8 bits, no parity, 1 stop */

        duart[uart_num]->u_mcr = 0x0b<<shift_val ;      /* Assert RTS, DTR & OUT2         */

        duart[uart_num]->u_fcr = 0x00<<shift_val ;      /* Clear 16552 FIFOs */

        /* Is the following write of 0x01 needed? */

        /* Let's try it without... */

        duart[uart_num]->u_fcr = 0xc7<<shift_val ;      /* Enable 16552 FIFOs */

        duart[uart_num]->u_ier = 0x07<<shift_val ;      /* Enable transmit/receive ints */

        tmp = duart[uart_num]->u_lsr ;          /* Re-arm interrupts            */

        tmp = duart[uart_num]->u_rdr ;

        tmp = duart[uart_num]->u_msr ;

        return(0);

}

        /*------------ end of duartinit function ----------------*/

    /***********************************************************************

     ***  Transmit character to host.

     ***********************************************************************/

int console_sps_putc(unsigned int uart_num, int ch)

{

        register unsigned short stat;

        if ( uart_num >= NUM_UARTS )

           return -1;

        /*

         *  Pause until there is room in the UART transmit

         *  buffer.

         */

        do {

                stat = duart[uart_num]->u_lsr>>shift_val;

        } while (!(stat & 0x40));

        /*

         *  Transmit data. (Junk)

         */

        TDR(ch)

        duart[uart_num]->u_tdr = ch<<shift_val ;

        return ch;

}

    /***********************************************************************

     ***  Read character from host.

     ***********************************************************************/

int console_sps_getc(unsigned int uart_num)

{

        register unsigned short stat;

        register int    ch;

        if ( uart_num >= NUM_UARTS )

           return -1;

        stat = duart[uart_num]->u_lsr>>shift_val;

        while (!(stat & 0x01))

        {

                rtems_task_wake_after( RTEMS_YIELD_PROCESSOR );

                stat = duart[uart_num]->u_lsr>>shift_val;

        }

        ch = duart[uart_num]->u_rdr>>shift_val;

        return ch;

}

    /***********************************************************************

     ***  check character from host.

     ***********************************************************************/

int console_sps_kbhit(unsigned int uart_num)

{

        register unsigned short stat;

        if ( uart_num >= NUM_UARTS )

           return -1;

        stat = duart[uart_num]->u_lsr>>shift_val;

        return ((stat & 0x01));

}