Subversion Repositories openrisc_2011-10-31

/*  page_table.c

 *

 *  The code submitted by Eric Vaitl <vaitl@viasat.com> for the MVME162 appears

 *  to be for a uniprocessor implementation. The function that sets up the

 *  page tables, page_table_init(), is not data driven. For all processors, it

 *  sets up page tables to map virtual addresses from 0x20000 to 0x3FFFFF to

 *  physical addresses 0x20000 to 0x3FFFFF. This presumably maps a subset of

 *  a local 4 MB space, which is probably the amount of RAM on Eric Vailt's

 *  MVME162.

 *

 *  It is possible to set up the various bus bridges in the MVME167s to create

 *  a flat physical address space across multiple boards, i.e., it is possible

 *  for each MVME167 in a multiprocessor system to access a given memory

 *  location using the same physical address, whether that location is in local

 *  or VME space. Addres translation can be set up so that each virtual address

 *  maps to its corresponding physical address, e.g. virtual address 0x12345678

 *  is mapped to physical address 0x12345678. With this mapping, the MMU is

 *  only used to control the caching modes for the various regions of memory.

 *  Mapping the virtual addresses to their corresponding physical address makes

 *  it unnecessary to map addresses under software control during the

 *  initialization of RTEMS, before address translation is turned on.

 *

 *  With the above approach, address translation may be set up either with the

 *  transparent address translation registers, or with page tables. If page

 *  tables are used, a more efficient use of page table space can be achieved

 *  by sharing the page tables between processors. The entire page table tree

 *  can be shared, or each processor can hold a private copy of the top nodes

 *  which point to leaf nodes stored on individual processors.

 *

 *  In this port, only the transparent address translation registers are used.

 *  We map the entire virtual range from 0x0 to 0x7FFFFFFF to the identical

 *  physical range 0x0 to 0x7FFFFFFF. We rely on the hardware to signal bus

 *  errors if we address non-existent memory within this range. Our two

 *  MVME167s are configured to exist at physical addresses 0x00800000 to

 *  0x00BFFFFF and 0x00C00000 to 0x00FFFFFF respectively. We map the space

 *  from 0x0 to 0x7FFFFFFF as copyback, unless jumper J1-5 is removed, in

 *  which case we map as writethrough. If jumper J1-7 is removed, the data

 *  cache is NOT enabled. If jumper J1-6 is removed, the instruction cache

 *  is not enabled.

 *

 *  Copyright (c) 1998, National Research Council of Canada

 *

 *  $Id: page_table.c,v 1.2 2001-09-27 12:00:20 chris Exp $

 */

#include <bsp.h>

#include <page_table.h>                 /* Nothing in here for us */

/*

 *  page_table_init

 *

 *  Map the virtual range 0x00000000--0x7FFFFFFF to the physical range

 *  0x00000000--0x7FFFFFFF. Rely on the hardware to raise exceptions when

 *  addressing non-existent memory. Use only the transparent translation

 *  registers (for now).

 *

 *  On all processors, the local virtual address range 0xFF000000--0xFFFFFFFF

 *  is mapped to the physical address range 0xFF000000--0xFFFFFFFF as

 *  caching disabled, serialized access.

 *

 *  Input parameters:

 *    config_table - ignored for now

 *

 *  Output parameters: NONE

 *

 *  Return values: NONE

 */

void page_table_init(

  rtems_configuration_table *config_table

)

{

  unsigned char j1;               /* State of J1 jumpers */

  register unsigned long dtt0;    /* Content of dtt0 */

  register unsigned long cacr;    /* Content of cacr */

  /*

   *  Logical base addr = 0x00    map starting at 0x00000000

   *  Logical address mask = 0x7F map up to 0x7FFFFFFF

   *  E = 0b1                     enable address translation

   *  S-Field = 0b1X              ignore FC2 when matching

   *  U1, U0 = 0b00               user page attributes not used

   *  CM = 0b01                   cachable, copyback

   *  W = 0b0                     read/write access allowed

   */

  dtt0 = 0x007FC020;

  cacr = 0x80008000;              /* Data and instruction cache on */

  /* Read the J1 header */

  j1 = (unsigned char)(lcsr->vector_base & 0xFF);

  if ( j1 & 0x80 )

    /* Jumper J1-7 if off, disable data caching */

    cacr &= 0x7FFFFFFF;

  if ( j1 & 0x40 )

    /* Jumper J1-6 if off, disable instruction caching */

    cacr &= 0xFFFF7FFF;

  if ( j1 & 0x20 )

    /* Jumper J1-5 is off, enable writethrough caching */

    dtt0 &= 0xFFFFFF9F;

  /* do it ! */

  asm volatile("movec %0, %%tc    /* turn off paged address translation */

                movec %0, %%cacr  /* disable both caches */

                cinva %%bc        /* clear both caches */

                movec %1,%%dtt0   /* block address translation on */

                movec %1,%%itt0

                movec %2,%%dtt1

                movec %2,%%itt1

                movec %3,%%cacr"  /* data cache on */

          :: "d" (0), "d" (dtt0), "d" (0xFF00C040), "d" (cacr));

}

/*

 *  page_table_teardown

 *

 *  Turn off paging. Turn off the cache. Flush the cache. Tear down

 *  the transparent translations.

 *

 *  Input parameters: NONE

 *

 *  Output parameters: NONE

 *

 *  Return values: NONE

 */

void page_table_teardown( void )

{

  asm volatile ("movec %0,%%tc

                 movec %0,%%cacr

                 cpusha %%bc

                 movec %0,%%dtt0

                 movec %0,%%itt0

                 movec %0,%%dtt1

                 movec %0,%%itt1"

    :: "d" (0) );

}