| 1 |
1275 |
phoenix |
Released 1994-06-13
|
| 2 |
|
|
|
| 3 |
|
|
|
| 4 |
|
|
CONTENTS:
|
| 5 |
|
|
|
| 6 |
|
|
1. Introduction.
|
| 7 |
|
|
2. License.
|
| 8 |
|
|
3. Files in this release.
|
| 9 |
|
|
4. Installation.
|
| 10 |
|
|
5. Problems and tuning.
|
| 11 |
|
|
6. Using the drivers with earlier releases.
|
| 12 |
|
|
7. Acknowledgments.
|
| 13 |
|
|
|
| 14 |
|
|
|
| 15 |
|
|
1. INTRODUCTION.
|
| 16 |
|
|
|
| 17 |
|
|
This is a set of Ethernet drivers for the D-Link DE-600/DE-620
|
| 18 |
|
|
pocket adapters, for the parallel port on a Linux based machine.
|
| 19 |
|
|
Some adapter "clones" will also work. Xircom is _not_ a clone...
|
| 20 |
|
|
These drivers _can_ be used as loadable modules,
|
| 21 |
|
|
and were developed for use on Linux 1.1.13 and above.
|
| 22 |
|
|
For use on Linux 1.0.X, or earlier releases, see below.
|
| 23 |
|
|
|
| 24 |
|
|
I have used these drivers for NFS, ftp, telnet and X-clients on
|
| 25 |
|
|
remote machines. Transmissions with ftp seems to work as
|
| 26 |
|
|
good as can be expected (i.e. > 80k bytes/sec) from a
|
| 27 |
|
|
parallel port...:-) Receive speeds will be about 60-80% of this.
|
| 28 |
|
|
Depending on your machine, somewhat higher speeds can be achieved.
|
| 29 |
|
|
|
| 30 |
|
|
All comments/fixes to Bjorn Ekwall (bj0rn@blox.se).
|
| 31 |
|
|
|
| 32 |
|
|
|
| 33 |
|
|
2. LICENSE.
|
| 34 |
|
|
|
| 35 |
|
|
This program is free software; you can redistribute it
|
| 36 |
|
|
and/or modify it under the terms of the GNU General Public
|
| 37 |
|
|
License as published by the Free Software Foundation; either
|
| 38 |
|
|
version 2, or (at your option) any later version.
|
| 39 |
|
|
|
| 40 |
|
|
This program is distributed in the hope that it will be
|
| 41 |
|
|
useful, but WITHOUT ANY WARRANTY; without even the implied
|
| 42 |
|
|
warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
|
| 43 |
|
|
PURPOSE. See the GNU General Public License for more
|
| 44 |
|
|
details.
|
| 45 |
|
|
|
| 46 |
|
|
You should have received a copy of the GNU General Public
|
| 47 |
|
|
License along with this program; if not, write to the Free
|
| 48 |
|
|
Software Foundation, Inc., 675 Mass Ave, Cambridge, MA
|
| 49 |
|
|
02139, USA.
|
| 50 |
|
|
|
| 51 |
|
|
|
| 52 |
|
|
3. FILES IN THIS RELEASE.
|
| 53 |
|
|
|
| 54 |
|
|
README.DLINK This file.
|
| 55 |
|
|
de600.c The Source (may it be with You :-) for the DE-600
|
| 56 |
|
|
de620.c ditto for the DE-620
|
| 57 |
|
|
de620.h Macros for de620.c
|
| 58 |
|
|
|
| 59 |
|
|
If you are upgrading from the d-link tar release, there will
|
| 60 |
|
|
also be a "dlink-patches" file that will patch Linux 1.1.18:
|
| 61 |
|
|
linux/drivers/net/Makefile
|
| 62 |
|
|
linux/drivers/net/CONFIG
|
| 63 |
|
|
linux/drivers/net/MODULES
|
| 64 |
|
|
linux/drivers/net/Space.c
|
| 65 |
|
|
linux/config.in
|
| 66 |
|
|
Apply the patch by:
|
| 67 |
|
|
"cd /usr/src; patch -p0 < linux/drivers/net/dlink-patches"
|
| 68 |
|
|
The old source, "linux/drivers/net/d_link.c", can be removed.
|
| 69 |
|
|
|
| 70 |
|
|
|
| 71 |
|
|
4. INSTALLATION.
|
| 72 |
|
|
|
| 73 |
|
|
o Get the latest net binaries, according to current net.wisdom.
|
| 74 |
|
|
|
| 75 |
|
|
o Read the NET-2 and Ethernet HOWTOs and modify your setup.
|
| 76 |
|
|
|
| 77 |
|
|
o If your parallel port has a strange address or irq,
|
| 78 |
|
|
modify "linux/drivers/net/CONFIG" accordingly, or adjust
|
| 79 |
|
|
the parameters in the "tuning" section in the sources.
|
| 80 |
|
|
|
| 81 |
|
|
If you are going to use the drivers as loadable modules, do _not_
|
| 82 |
|
|
enable them while doing "make config", but instead make sure that
|
| 83 |
|
|
the drivers are included in "linux/drivers/net/MODULES".
|
| 84 |
|
|
|
| 85 |
|
|
If you are _not_ going to use the driver(s) as loadable modules,
|
| 86 |
|
|
but instead have them included in the kernel, remember to enable
|
| 87 |
|
|
the drivers while doing "make config".
|
| 88 |
|
|
|
| 89 |
|
|
o To include networking and DE600/DE620 support in your kernel:
|
| 90 |
|
|
# cd /linux
|
| 91 |
|
|
(as modules:)
|
| 92 |
|
|
# make config (answer yes on CONFIG_NET and CONFIG_INET)
|
| 93 |
|
|
(else included in the kernel:)
|
| 94 |
|
|
# make config (answer yes on CONFIG _NET, _INET and _DE600 or _DE620)
|
| 95 |
|
|
# make clean
|
| 96 |
|
|
# make depend
|
| 97 |
|
|
# make zImage (or whatever magic you usually do)
|
| 98 |
|
|
|
| 99 |
|
|
o I use lilo to boot multiple kernels, so that I at least
|
| 100 |
|
|
can have one working kernel :-). If you do too, append
|
| 101 |
|
|
these lines to /etc/lilo/config:
|
| 102 |
|
|
|
| 103 |
|
|
image = /linux/zImage
|
| 104 |
|
|
label = newlinux
|
| 105 |
|
|
root = /dev/hda2 (or whatever YOU have...)
|
| 106 |
|
|
|
| 107 |
|
|
# /etc/lilo/install
|
| 108 |
|
|
|
| 109 |
|
|
o Do "sync" and reboot the new kernel with a D-Link
|
| 110 |
|
|
DE-600/DE-620 pocket adapter connected.
|
| 111 |
|
|
|
| 112 |
|
|
o The adapter can be configured with ifconfig eth?
|
| 113 |
|
|
where the actual number is decided by the kernel
|
| 114 |
|
|
when the drivers are initialized.
|
| 115 |
|
|
|
| 116 |
|
|
|
| 117 |
|
|
5. "PROBLEMS" AND TUNING,
|
| 118 |
|
|
|
| 119 |
|
|
o If you see error messages from the driver, and if the traffic
|
| 120 |
|
|
stops on the adapter, try to do "ifconfig" and "route" once
|
| 121 |
|
|
more, just as in "rc.inet1". This should take care of most
|
| 122 |
|
|
problems, including effects from power loss, or adapters that
|
| 123 |
|
|
aren't connected to the printer port in some way or another.
|
| 124 |
|
|
You can somewhat change the behaviour by enabling/disabling
|
| 125 |
|
|
the macro SHUTDOWN_WHEN_LOST in the "tuning" section.
|
| 126 |
|
|
For the DE-600 there is another macro, CHECK_LOST_DE600,
|
| 127 |
|
|
that you might want to read about in the "tuning" section.
|
| 128 |
|
|
|
| 129 |
|
|
o Some machines have trouble handling the parallel port and
|
| 130 |
|
|
the adapter at high speed. If you experience problems:
|
| 131 |
|
|
|
| 132 |
|
|
DE-600:
|
| 133 |
|
|
- The adapter is not recognized at boot, i.e. an Ethernet
|
| 134 |
|
|
address of 00:80:c8:... is not shown, try to add another
|
| 135 |
|
|
"; SLOW_DOWN_IO"
|
| 136 |
|
|
at DE600_SLOW_DOWN in the "tuning" section. As a last resort,
|
| 137 |
|
|
uncomment: "#define REALLY_SLOW_IO" (see for hints).
|
| 138 |
|
|
|
| 139 |
|
|
- You experience "timeout" messages: first try to add another
|
| 140 |
|
|
"; SLOW_DOWN_IO"
|
| 141 |
|
|
at DE600_SLOW_DOWN in the "tuning" section, _then_ try to
|
| 142 |
|
|
increase the value (original value: 5) at
|
| 143 |
|
|
"if (tickssofar < 5)" near line 422.
|
| 144 |
|
|
|
| 145 |
|
|
DE-620:
|
| 146 |
|
|
- Your parallel port might be "sluggish". To cater for
|
| 147 |
|
|
this, there are the macros LOWSPEED and READ_DELAY/WRITE_DELAY
|
| 148 |
|
|
in the "tuning" section. Your first step should be to enable
|
| 149 |
|
|
LOWSPEED, and after that you can "tune" the XXX_DELAY values.
|
| 150 |
|
|
|
| 151 |
|
|
o If the adapter _is_ recognized at boot but you get messages
|
| 152 |
|
|
about "Network Unreachable", then the problem is probably
|
| 153 |
|
|
_not_ with the driver. Check your net configuration instead
|
| 154 |
|
|
(ifconfig and route) in "rc.inet1".
|
| 155 |
|
|
|
| 156 |
|
|
o There is some rudimentary support for debugging, look at
|
| 157 |
|
|
the source. Use "-DDE600_DEBUG=3" or "-DDE620_DEBUG=3"
|
| 158 |
|
|
when compiling, or include it in "linux/drivers/net/CONFIG".
|
| 159 |
|
|
IF YOU HAVE PROBLEMS YOU CAN'T SOLVE: PLEASE COMPILE THE DRIVER
|
| 160 |
|
|
WITH DEBUGGING ENABLED, AND SEND ME THE RESULTING OUTPUT!
|
| 161 |
|
|
|
| 162 |
|
|
|
| 163 |
|
|
6. USING THE DRIVERS WITH EARLIER RELEASES.
|
| 164 |
|
|
|
| 165 |
|
|
The later 1.1.X releases of the Linux kernel include some
|
| 166 |
|
|
changes in the networking layer (a.k.a. NET3). This affects
|
| 167 |
|
|
these drivers in a few places. The hints that follow are
|
| 168 |
|
|
_not_ tested by me, since I don't have the disk space to keep
|
| 169 |
|
|
all releases on-line.
|
| 170 |
|
|
Known needed changes to date:
|
| 171 |
|
|
- release patchfile: some patches will fail, but they should
|
| 172 |
|
|
be easy to apply "by hand", since they are trivial.
|
| 173 |
|
|
(Space.c: d_link_init() is now called de600_probe())
|
| 174 |
|
|
- de600.c: change "mark_bh(NET_BH)" to "mark_bh(INET_BH)".
|
| 175 |
|
|
- de620.c: (maybe) change the code around "netif_rx(skb);" to be
|
| 176 |
|
|
similar to the code around "dev_rint(...)" in de600.c
|
| 177 |
|
|
|
| 178 |
|
|
|
| 179 |
|
|
7. ACKNOWLEDGMENTS.
|
| 180 |
|
|
|
| 181 |
|
|
These drivers wouldn't have been done without the base
|
| 182 |
|
|
(and support) from Ross Biro ,
|
| 183 |
|
|
and D-Link Systems Inc. The driver relies upon GPL-ed
|
| 184 |
|
|
source from D-Link Systems Inc. and from Russel Nelson at
|
| 185 |
|
|
Crynwr Software .
|
| 186 |
|
|
|
| 187 |
|
|
Additional input also from:
|
| 188 |
|
|
Donald Becker , Alan Cox
|
| 189 |
|
|
and Fred N. van Kempen
|
| 190 |
|
|
|
| 191 |
|
|
DE-600 alpha release primary victim^H^H^H^H^H^Htester:
|
| 192 |
|
|
- Erik Proper .
|
| 193 |
|
|
Good input also from several users, most notably
|
| 194 |
|
|
- Mark Burton .
|
| 195 |
|
|
|
| 196 |
|
|
DE-620 alpha release victims^H^H^H^H^H^H^Htesters:
|
| 197 |
|
|
- J. Joshua Kopper
|
| 198 |
|
|
- Olav Kvittem
|
| 199 |
|
|
- Germano Caronni
|
| 200 |
|
|
- Jeremy Fitzhardinge
|
| 201 |
|
|
|
| 202 |
|
|
|
| 203 |
|
|
Happy hacking!
|
| 204 |
|
|
|
| 205 |
|
|
Bjorn Ekwall == bj0rn@blox.se
|
