Subversion Repositories or1k

HiSax is a Linux hardware-level driver for passive ISDN cards with Siemens

chipset (ISAC_S 2085/2086/2186, HSCX SAB 82525). It is based on the Teles

driver from Jan den Ouden.

It is meant to be used with isdn4linux, an ISDN link-level module for Linux

written by Fritz Elfert.

    This program is free software; you can redistribute it and/or modify

    it under the terms of the GNU General Public License as published by

    the Free Software Foundation; either version 2 of the License, or

    (at your option) any later version.

    This program is distributed in the hope that it will be useful,

    but WITHOUT ANY WARRANTY; without even the implied warranty of

    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License

    along with this program; if not, write to the Free Software

    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.

Supported cards

---------------

Teles 8.0/16.0/16.3 and compatible ones

Teles 16.3c

Teles S0/PCMCIA

Teles PCI

Teles S0Box

Creatix S0Box

Creatix PnP S0

Compaq ISDN S0 ISA card

AVM A1 (Fritz, Teledat 150)

AVM Fritz PCMCIA

AVM Fritz PnP

AVM Fritz PCI

ELSA Microlink PCC-16, PCF, PCF-Pro, PCC-8

ELSA Quickstep 1000

ELSA Quickstep 1000PCI

ELSA Quickstep 3000 (same settings as QS1000)

ELSA Quickstep 3000PCI

ELSA PCMCIA

ITK ix1-micro Rev.2

Eicon.Diehl Diva 2.0 ISA and PCI (S0 and U interface, no PRO version)

Eicon.Diehl Diva Piccola

ASUSCOM NETWORK INC. ISDNLink 128K PC adapter (order code I-IN100-ST-D)

Dynalink IS64PH (OEM version of ASUSCOM NETWORK INC. ISDNLink 128K adapter)

PCBIT-DP (OEM version of ASUSCOM NETWORK INC. ISDNLink)

HFC-2BS0 based cards (TeleInt SA1)

Sedlbauer Speed Card (Speed Win, Teledat 100, PCI, Fax+)

Sedlbauer Speed Star/Speed Star2 (PCMCIA)

Sedlbauer ISDN-Controller PC/104

USR Sportster internal TA (compatible Stollmann tina-pp V3)

ith Kommunikationstechnik GmbH MIC 16 ISA card

Traverse Technologie NETjet PCI S0 card

Dr. Neuhaus Niccy PnP/PCI

Note: PCF, PCF-Pro: up to now, only the ISDN part is supported

      PCC-8: not tested yet

      Teles PCMCIA is EXPERIMENTAL

      Teles 16.3c is EXPERIMENTAL

      Teles PCI is EXPERIMENTAL

      Teles S0Box is EXPERIMENTAL

      Eicon.Diehl Diva U interface not tested

If you know other passive cards with the Siemens chipset, please let me know.

To use the PNP cards you need the isapnptools.

You can combine any card, if there is no conflict between the ressources

(io, mem, irq).

Configuring the driver

----------------------

The HiSax driver can either be built directly into the kernel or as a module.

It can be configured using the command line feature while loading the kernel

with LILO or LOADLIN or, if built as a module, using insmod/modprobe with

parameters.

There is also some config needed before you compile the kernel and/or

modules. It is included in the normal "make [menu]config" target at the

kernel. Don't forget it, especially to select the right D-channel protocol.

Please note: All PnP cards need to be configured with isapnp and will work

only with the HiSax driver used as a module.

a) when built as a module

-------------------------

insmod/modprobe  hisax.o \

  io=iobase irq=IRQ mem=membase type=card_type \

  protocol=D_channel_protocol id=idstring

or, if several cards are installed:

insmod/modprobe hisax.o \

  io=iobase1,iobase2,... irq=IRQ1,IRQ2,... mem=membase1,membase2,... \

  type=card_type1,card_type2,... \

  protocol=D_channel_protocol1,D_channel_protocol2,... \

  id=idstring1%idstring2 ...

where "iobaseN" represents the I/O base address of the Nth card, "membaseN"

the memory base address of the Nth card, etc.

The reason for the delimiter "%" being used in the idstrings is that ","

won't work with the current modules package.

The parameters may be specified in any order. For example, the "io"

parameter may precede the "irq" parameter, or vice versa. If several

cards are installed, the ordering within the comma separated parameter

lists must of course be consistent.

Only parameters applicable to the card type need to be specified. For

example, the Teles 16.3 card is not memory-mapped, so the "mem"

parameter may be omitted for this card. Sometimes it may be necessary

to specify a dummy parameter, however. This is the case when there is

a card of a different type later in the list that needs a parameter

which the preceding card does not. For instance, if a Teles 16.0 card

is listed after a Teles 16.3 card, a dummy memory base parameter of 0

must be specified for the 16.3. Instead of a dummy value, the parameter

can also be skipped by simply omitting the value. For example:

mem=,0xd0000. See example 6 below.

The parameter for the D-Channel protocol may be omitted if you selected the

correct one during kernel config. Valid values are "1" for German 1TR6,

"2" for EDSS1 (Euro ISDN) and "3" for leased lines (no D-Channel).

The Creatix/Teles PnP cards use io1= and io2= instead of io= for specifying

the I/O addresses of the ISAC and HSCX chips, respectively.

Card types:

    Type                Required parameters (in addition to type and protocol)

    1   Teles 16.0               irq, mem, io

    2   Teles  8.0               irq, mem

    3   Teles 16.3 (non PnP)     irq, io

    4   Creatix/Teles PnP        irq, io0 (ISAC), io1 (HSCX)

    5   AVM A1 (Fritz)           irq, io

    6   ELSA PCC/PCF cards       io or nothing for autodetect (the iobase is

                                 required only if you have more than one ELSA

                                 card in your PC)

    7   ELSA Quickstep 1000      irq, io  (from isapnp setup)

    8   Teles 16.3 PCMCIA        irq, io

    9   ITK ix1-micro Rev.2      irq, io

   10   ELSA PCMCIA              irq, io  (set with card manager)

   11   Eicon.Diehl Diva ISA PnP irq, io

   11   Eicon.Diehl Diva PCI     no parameter

   12   ASUS COM ISDNLink        irq, io  (from isapnp setup)

   13   HFC-2BS0 based cards     irq, io

   14   Teles 16.3c PnP          irq, io

   15   Sedlbauer Speed Card     irq, io

   15   Sedlbauer PC/104         irq, io

   15   Sedlbauer Speed PCI      no parameter

   16   USR Sportster internal   irq, io

   17   MIC card                 irq, io

   18   ELSA Quickstep 1000PCI   no parameter

   19   Compaq ISDN S0 ISA card  irq, io0, io1, io (from isapnp setup io=IO2)

   20   NETjet PCI card          no parameter

   21   Teles PCI                no parameter

   22   Sedlbauer Speed Star (PCMCIA) irq, io (set with card manager)

   24   Dr. Neuhaus Niccy PnP    irq, io0, io1 (from isapnp setup)

   24   Dr. Neuhaus Niccy PCI    no parameter

   25   Teles S0Box              irq, io (of the used lpt port)

   26   AVM A1 PCMCIA (Fritz!)   irq, io (set with card manager)

   27   AVM PnP (Fritz!PnP)      irq, io  (from isapnp setup)

   27   AVM PCI (Fritz!PCI)      no parameter

   28   Sedlbauer Speed Fax+     irq, io (from isapnp setup)

At the moment IRQ sharing is only possible with PCI cards. Please make sure

that your IRQ is free and enabled for ISA use.

Examples for module loading

1. Teles 16.3, Euro ISDN, I/O base 280 hex, IRQ 10

   modprobe hisax type=3 protocol=2 io=0x280 irq=10

2. Teles 16.0, 1TR6 ISDN, I/O base d80 hex, IRQ 5, Memory d0000 hex

   modprobe hisax protocol=1 type=1 io=0xd80 mem=0xd0000 irq=5

3. Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and ELSA PCF, Euro ISDN

   modprobe hisax type=5,6 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa

4. Any ELSA PCC/PCF card, Euro ISDN

   modprobe hisax type=6 protocol=2

5. Teles 16.3 PnP, Euro ISDN, with isapnp configured

   isapnp config:  (INT 0 (IRQ 10 (MODE +E)))

                   (IO 0 (BASE 0x0580))

                   (IO 1 (BASE 0x0180))

   modprobe hisax type=4 protocol=2 irq=10 io0=0x580 io1=0x180

6. Teles 16.3, Euro ISDN, I/O base 280 hex, IRQ 12 and

   Teles 16.0, 1TR6, IRQ 5, Memory d0000 hex

   modprobe hisax type=3,1 protocol=2,1 io=0x280 mem=0,0xd0000

   Please note the dummy 0 memory address for the Teles 16.3, used as a

   placeholder as described above, in the last example.

7. Teles PCMCIA, Euro ISDN, I/O base 180 hex, IRQ 15 (default values)

   modprobe hisax type=8 protocol=2 io=0x180 irq=15

b) using LILO/LOADLIN, with the driver compiled directly into the kernel

------------------------------------------------------------------------

hisax=typ1,dp1,pa_1,pb_1,pc_1[,typ2,dp2,pa_2 ... \

      typn,dpn,pa_n,pb_n,pc_n][,idstring1[,idstring2,...,idstringn]]

where

     typ1 = type of 1st card (default depends on kernel settings)

     dp1  = D-Channel protocol of 1st card. 1=1TR6, 2=EDSS1, 3=leased

     pa_1 = 1st parameter (depending on the type of the card)

     pb_1 = 2nd parameter (    "     "   "   "   "   "   "  )

     pc_1 = 3rd parameter (    "     "   "   "   "   "   "  )

     typ2,dp2,pa_2,pb_2,pc_2 = Parameters of the second card (defaults: none)

     typn,dpn,pa_n,pb_n,pc_n = Parameters of the n'th card (up to 16 cards are

                                                                     supported)

     idstring = Driver ID for accessing the particular card with utility

                programs and for identification when using a line monitor

                (default: "HiSax")

                Note: the ID string must start with an alphabetical character!

Card types:

type

    1   Teles 16.0              pa=irq  pb=membase  pc=iobase

    2   Teles  8.0              pa=irq  pb=membase

    3   Teles 16.3              pa=irq  pb=iobase

    4   Creatix/Teles PNP       ONLY WORKS AS A MODULE !

    5   AVM A1 (Fritz)          pa=irq  pb=iobase

    6   ELSA PCC/PCF cards      pa=iobase or nothing for autodetect

    7   ELSA Quickstep 1000     ONLY WORKS AS A MODULE !

    8   Teles S0 PCMCIA         pa=irq  pb=iobase

    9   ITK ix1-micro Rev.2     pa=irq  pb=iobase

   10   ELSA PCMCIA             pa=irq, pb=io  (set with card manager)

   11   Eicon.Diehl Diva ISAPnP ONLY WORKS AS A MODULE !

   11   Eicon.Diehl Diva PCI    no parameter

   12   ASUS COM ISDNLink       ONLY WORKS AS A MODULE !

   13   HFC-2BS0 based cards    pa=irq  pb=io

   14   Teles 16.3c PnP         ONLY WORKS AS A MODULE !

   15   Sedlbauer Speed Card    pa=irq  pb=io (Speed Win only as module !)

   15   Sedlbauer PC/104        pa=irq  pb=io

   15   Sedlbauer Speed PCI     no parameter

   16   USR Sportster internal  pa=irq  pb=io

   17   MIC card                pa=irq  pb=io

   18   ELSA Quickstep 1000PCI  no parameter

   19   Compaq ISDN S0 ISA card ONLY WORKS AS A MODULE !

   20   NETjet PCI card         no parameter

   21   Teles PCI               no parameter

   22   Sedlbauer Speed Star (PCMCIA)  pa=irq, pb=io  (set with card manager)

   24   Dr. Neuhaus Niccy PnP   ONLY WORKS AS A MODULE !

   24   Dr. Neuhaus Niccy PCI   no parameter

   25   Teles S0Box             irq, io (of the used lpt port)

   26   AVM A1 PCMCIA (Fritz!)  irq, io (set with card manager)

   27   AVM PnP (Fritz!PnP)     ONLY WORKS AS A MODULE !

   27   AVM PCI (Fritz!PCI)     no parameter

   28   Sedlbauer Speed Fax+    ONLY WORKS AS A MODULE !

Running the driver

------------------

When you insmod isdn.o and hisax.o (or with the in-kernel version, during

boot time), a few lines should appear in your syslog. Look for something like:

Apr 13 21:01:59 kke01 kernel: HiSax: Driver for Siemens chip set ISDN cards

Apr 13 21:01:59 kke01 kernel: HiSax: Version 2.9

Apr 13 21:01:59 kke01 kernel: HiSax: Revisions 1.14/1.9/1.10/1.25/1.8

Apr 13 21:01:59 kke01 kernel: HiSax: Total 1 card defined

Apr 13 21:01:59 kke01 kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax1 (0)

Apr 13 21:01:59 kke01 kernel: HiSax: Elsa driver Rev. 1.13

...

Apr 13 21:01:59 kke01 kernel: Elsa: PCF-Pro found at 0x360 Rev.:C IRQ 10

Apr 13 21:01:59 kke01 kernel: Elsa: timer OK; resetting card

Apr 13 21:01:59 kke01 kernel: Elsa: HSCX version A: V2.1  B: V2.1

Apr 13 21:01:59 kke01 kernel: Elsa: ISAC 2086/2186 V1.1

...

Apr 13 21:01:59 kke01 kernel: HiSax: DSS1 Rev. 1.14

Apr 13 21:01:59 kke01 kernel: HiSax: 2 channels added

This means that the card is ready for use.

Cabling problems or line-downs are not detected, and only some ELSA cards can

detect the S0 power.

Remember that, according to the new strategy for accessing low-level drivers

from within isdn4linux, you should also define a driver ID while doing

insmod: Simply append hisax_id= to the insmod command line. This

string MUST NOT start with a digit or a small 'x'!

At this point you can run a 'cat /dev/isdnctrl0' and view debugging messages.

At the moment, debugging messages are enabled with the hisaxctrl tool:

    hisaxctrl  DebugCmd 

 default is HiSax, if you didn't specify one.

DebugCmd is  1  for generic debugging

            11  for layer 1 development debugging

            13  for layer 3 development debugging

where  is the integer sum of the following debugging

options you wish enabled:

With DebugCmd set to 1:

   0x0001  Link-level <--> hardware-level communication

   0x0002  Top state machine

   0x0004  D-Channel Frames for isdnlog

   0x0008  D-Channel Q.921

   0x0010  B-Channel X.75

   0x0020  D-Channel l2

   0x0040  B-Channel l2

   0x0080  D-Channel link state debugging

   0x0100  B-Channel link state debugging

   0x0200  TEI debug

   0x0400  LOCK debug in callc.c

   0x0800  More paranoid debug in callc.c (not for normal use)

   0x1000  D-Channel l1 state debugging

   0x2000  B-Channel l1 state debugging

With DebugCmd set to 11:

   0x0001  Warnings (default: on)

   0x0002  IRQ status

   0x0004  ISAC

   0x0008  ISAC FIFO

   0x0010  HSCX

   0x0020  HSCX FIFO (attention: full B-Channel output!)

   0x0040  D-Channel LAPD frame types

   0x0080  IPAC debug

   0x0100  HFC receive debug

   0x0200  ISAC monitor debug

   0x0400  D-Channel frames for isdnlog (set with 1 0x4 too)

   0x0800  D-Channel message verbose

With DebugCmd set to 13:

         1  Warnings (default: on)

         2  l3 protocol descriptor errors

         4  l3 state machine

         8  charge info debugging (1TR6)

For example, 'hisaxctrl HiSax 1 0x3ff' enables full generic debugging.

Because of some obscure problems with some switch equipment, the delay

between the CONNECT message and sending the first data on the B-channel is now

configurable with

hisaxctrl  2 

 in ms Value between 50 and 800 ms is recommended.

Downloading Firmware

--------------------

At the moment, the Sedlbauer speed fax+ is the only card, which

needs to download firmware.

The firmware is downloaded with the hisaxctrl tool:

    hisaxctrl  9 

 default is HiSax, if you didn't specify one,

where  is the filename of the firmware file.

For example, 'hisaxctrl HiSax 9 ISAR.BIN' downloads the firmware for

ISAR based cards (like the Sedlbauer speed fax+).

Warning

-------

HiSax is a work in progress and may crash your machine.

For certification look at HiSax.cert file.

Limitations

-----------

At this time, HiSax only works on Euro ISDN lines and German 1TR6 lines.

For leased lines see appendix.

Bugs

----

If you find any, please let me know.

Thanks

------

Special thanks to:

        Emil Stephan for the name HiSax which is a mix of HSCX and ISAC.

        Fritz Elfert, Jan den Ouden, Michael Hipp, Michael Wein,

        Andreas Kool, Pekka Sarnila, Sim Yskes, Johan Myrre'en,

        Klaus-Peter Nischke (ITK AG), Christof Petig, Werner Fehn (ELSA GmbH),

        Volker Schmidt

        Edgar Toernig and Marcus Niemann for the Sedlbauer driver

        Stephan von Krawczynski

        Juergen Quade for the Leased Line part

        Klaus Lichtenwalder (Klaus.Lichtenwalder@WebForum.DE), for ELSA PCMCIA support

        Enrik Berkhan (enrik@starfleet.inka.de) for S0BOX specific stuff

        Ton van Rosmalen for Teles PCI

        and more people who are hunting bugs. (If I forgot somebody, please

        send me a mail).

        Firma ELSA GmbH

        Firma Eicon.Diehl GmbH

        Firma Dynalink NL

        Firma ASUSCOM NETWORK INC. Taiwan

        Firma S.u.S.E

        Firma ith Kommunikationstechnik GmbH

        Firma Traverse Technologie Australia

        Firma Medusa GmbH  (www.medusa.de).

        Firma Quant-X Austria for sponsoring a DEC Alpha board+CPU

        Firma Cologne Chip Designs GmbH

        My girl friend and partner in life Ute for her patience with me.

Enjoy,

Karsten Keil

keil@isdn4linux.de

Appendix: Teles PCMCIA driver

-----------------------------

See

   http://www.stud.uni-wuppertal.de/~ea0141/pcmcia.html

for instructions.

Appendix: Linux and ISDN-leased lines

-------------------------------------

Original from Juergen Quade, new version KKe.

Attention NEW VERSION, the old leased line syntax won't work !!!

You can use HiSax to connect your Linux-Box via an ISDN leased line

to e.g. the Internet:

1. Build a kernel which includes the HiSax driver either as a module

   or as part of the kernel.

     cd /usr/src/linux

     make menuconfig

     make clean; make dep; make zImage; make modules; make modules_install

2. Install the new kernel

     cp /usr/src/linux/arch/i386/boot/zImage /etc/kernel/linux.isdn

     vi /etc/lilo.conf

     lilo

3. in case the hisax driver is a "fixed" part of the kernel, configure

   the driver with lilo:

     vi /etc/lilo.conf

     lilo

   Your lilo.conf _might_ look like the following:

        # LILO configuration-file

        # global section

    # teles 16.0 on IRQ=5, MEM=0xd8000, PORT=0xd80

        append="hisax=1,3,5,0xd8000,0xd80,HiSax"

    # teles 16.3 (non pnp) on IRQ=15, PORT=0xd80

        # append="hisax=3,3,5,0xd8000,0xd80,HiSax"

        boot=/dev/sda

        compact        # faster, but won't work on all systems.

        linear

        read-only

        prompt

        timeout=100

        vga = normal    # force sane state

        # Linux bootable partition config begins

        image = /etc/kernel/linux.isdn

        root = /dev/sda1

        label = linux.isdn

        #

        image = /etc/kernel/linux-2.0.30

        root = /dev/sda1

        label = linux.secure

   In the line starting with "append" you have to adapt the parameters

   according to your card (see above in this file)

3. boot the new linux.isdn kernel

4. start the ISDN subsystem:

   a) load - if necessary - the modules (depends, whether you compiled

      the ISDN driver as module or not)

      According to the type of card you have to specify the necessary

      driver parameter (irq, io, mem, type, protocol).

      For the leased line the protocol is "3". See the table above for

      the parameters, which you have to specify depending on your card.

   b) configure i4l

      /sbin/isdnctrl addif isdn0

      # EAZ  1 -- B1 channel   2 --B2 channel

      /sbin/isdnctrl eaz isdn0 1

      /sbin/isdnctrl secure isdn0 on

      /sbin/isdnctrl huptimeout isdn0 0

      /sbin/isdnctrl l2_prot isdn0 hdlc

      # Attention you must not set an outgoing number !!! This won't work !!!

      # The incomming number is LEASED0 for the first card, LEASED1 for the

      # second and so on.

      /sbin/isdnctrl addphone isdn0 in LEASED0

      # Here is no need to bind the channel.

   c) in case the remote partner is a CISCO:

      /sbin/isdnctrl encap isdn0 cisco-h

   d) configure the interface

      /sbin/ifconfig isdn0 ${LOCAL_IP} pointopoint ${REMOTE_IP}

   e) set the routes

      /sbin/route add -host ${REMOTE_IP} isdn0

      /sbin/route add default gw ${REMOTE_IP}

   f) switch the card into leased mode for each used B-channel

      /sbin/hisaxctrl HiSax 5 1

Remarks:

a) If you have a CISCO don't forget to switch off the KEEP ALIVE option!

b) Use state of the art isdn4k-utils

Here an example script:

#!/bin/sh

# Start/Stop ISDN lesaed line connection

I4L_AS_MODULE=yes

I4L_REMOTE_IS_CISCO=no

I4L_MODULE_PARAMS="type=16 io=0x268 irq=7 "

I4L_DEBUG=no

I4L_LEASED_128K=yes

LOCAL_IP=192.168.1.1

REMOTE_IP=192.168.2.1

case "$1" in

    start)

        echo "Starting ISDN ..."

        if [ ${I4L_AS_MODULE} = "yes" ]; then

                echo "loading modules..."

                /sbin/modprobe hisax ${I4L_MODULE_PARAMS}

        fi

        # configure interface

        /sbin/isdnctrl addif isdn0

        /sbin/isdnctrl secure isdn0 on

        if [ ${I4L_DEBUG} = "yes" ]; then

                /sbin/isdnctrl verbose 7

                /sbin/hisaxctrl HiSax 1 0xffff

                /sbin/hisaxctrl HiSax 11 0xff

                cat  /dev/isdnctrl >/tmp/lea.log &

        fi

        if [ ${I4L_REMOTE_IS_CISCO} = "yes" ]; then

                /sbin/isdnctrl encap isdn0 cisco-h

        fi

        /sbin/isdnctrl huptimeout isdn0 0

        # B-CHANNEL 1

        /sbin/isdnctrl eaz isdn0 1

        /sbin/isdnctrl l2_prot isdn0 hdlc

        # 1. card

        /sbin/isdnctrl addphone isdn0 in LEASED0

        if [ ${I4L_LEASED_128K} = "yes" ]; then

                /sbin/isdnctrl addslave isdn0 isdn0s

                /sbin/isdnctrl secure isdn0s on

                /sbin/isdnctrl huptimeout isdn0s 0

                # B-CHANNEL 2

                /sbin/isdnctrl eaz isdn0s 2

                /sbin/isdnctrl l2_prot isdn0s hdlc

                # 1. card

                /sbin/isdnctrl addphone isdn0s in LEASED0

                if [ ${I4L_REMOTE_IS_CISCO} = "yes" ]; then

                        /sbin/isdnctrl encap isdn0s cisco-h

                fi

        fi

        /sbin/isdnctrl status isdn0 on

        # configure tcp/ip

        /sbin/ifconfig isdn0 ${LOCAL_IP} pointopoint ${REMOTE_IP}

        /sbin/route add -host ${REMOTE_IP} isdn0

        /sbin/route add default gw ${REMOTE_IP}

        # switch to leased mode

        # B-CHANNEL 1

        /sbin/hisaxctrl HiSax 5 1

        if [ ${I4L_LEASED_128K} = "yes" ]; then

                # B-CHANNEL 2

                /sbin/hisaxctrl HiSax 5 2

        fi

        ;;

    stop)

        /sbin/ifconfig isdn0 down

        /sbin/isdnctrl delif isdn0

        if [ ${I4L_DEBUG} = "yes" ]; then

                killall cat

        fi

        if [ ${I4L_AS_MODULE} = "yes" ]; then

                /sbin/rmmod hisax

                /sbin/rmmod isdn

                /sbin/rmmod ppp

                /sbin/rmmod slhc

        fi

        ;;

    *)

        echo "Usage: $0 {start|stop}"

        exit 1

esac

exit 0