OpenCores
URL https://opencores.org/ocsvn/or1k/or1k/trunk

Subversion Repositories or1k

[/] [or1k/] [trunk/] [gdb-5.0/] [gdb/] [config/] [i386/] [nm-i386sol2.h] - Blame information for rev 107

Go to most recent revision | Details | Compare with Previous | View Log

Line No. Rev Author Line
1 106 markom
/* Native support for i386 running Solaris 2.
2
   Copyright 1998 Free Software Foundation, Inc.
3
 
4
   This file is part of GDB.
5
 
6
   This program is free software; you can redistribute it and/or modify
7
   it under the terms of the GNU General Public License as published by
8
   the Free Software Foundation; either version 2 of the License, or
9
   (at your option) any later version.
10
 
11
   This program is distributed in the hope that it will be useful,
12
   but WITHOUT ANY WARRANTY; without even the implied warranty of
13
   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
14
   GNU General Public License for more details.
15
 
16
   You should have received a copy of the GNU General Public License
17
   along with this program; if not, write to the Free Software
18
   Foundation, Inc., 59 Temple Place - Suite 330,
19
   Boston, MA 02111-1307, USA.  */
20
 
21
#include "nm-sysv4.h"
22
 
23
#ifdef NEW_PROC_API     /* Solaris 6 and above can do HW watchpoints */
24
 
25
#define TARGET_HAS_HARDWARE_WATCHPOINTS
26
 
27
/* The man page for proc4 on solaris 6 and 7 says that the system
28
   can support "thousands" of hardware watchpoints, but gives no
29
   method for finding out how many.  So just tell GDB 'yes'.  */
30
#define TARGET_CAN_USE_HARDWARE_WATCHPOINT(TYPE, CNT, OT) 1
31
 
32
/* When a hardware watchpoint fires off the PC will be left at the
33
   instruction following the one which caused the watchpoint.
34
   It will *NOT* be necessary for GDB to step over the watchpoint. */
35
#define HAVE_CONTINUABLE_WATCHPOINT
36
 
37
/* Solaris x86 2.6 and 2.7 targets have a kernel bug when stepping
38
   over an instruction that causes a page fault without triggering
39
   a hardware watchpoint. The kernel properly notices that it shouldn't
40
   stop, because the hardware watchpoint is not triggered, but it forgets
41
   the step request and continues the program normally.
42
   Work around the problem by removing hardware watchpoints if a step is
43
   requested, GDB will check for a hardware watchpoint trigger after the
44
   step anyway.  */
45
#define CANNOT_STEP_HW_WATCHPOINTS
46
 
47
extern int procfs_stopped_by_watchpoint PARAMS ((int));
48
#define STOPPED_BY_WATCHPOINT(W) \
49
  procfs_stopped_by_watchpoint(inferior_pid)
50
 
51
/* Use these macros for watchpoint insertion/deletion.  */
52
/* type can be 0: write watch, 1: read watch, 2: access watch (read/write) */
53
 
54
extern int procfs_set_watchpoint PARAMS ((int, CORE_ADDR, int, int, int));
55
#define target_insert_watchpoint(ADDR, LEN, TYPE) \
56
        procfs_set_watchpoint (inferior_pid, ADDR, LEN, TYPE, 1)
57
#define target_remove_watchpoint(ADDR, LEN, TYPE) \
58
        procfs_set_watchpoint (inferior_pid, ADDR, 0, 0, 0)
59
 
60
#endif /* NEW_PROC_API */

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.