Subversion Repositories or1k

/* @(#)error.h  5.18 93/07/30 16:39:48, Srini, AMD */

/******************************************************************************

 * Copyright 1991 Advanced Micro Devices, Inc.

 *

 * This software is the property of Advanced Micro Devices, Inc  (AMD)  which

 * specifically  grants the user the right to modify, use and distribute this

 * software provided this notice is not removed or altered.  All other rights

 * are reserved by AMD.

 *

 * AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS

 * SOFTWARE.  IN NO EVENT SHALL AMD BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

 * DAMAGES IN CONNECTION WITH OR ARISING FROM THE FURNISHING, PERFORMANCE, OR

 * USE OF THIS SOFTWARE.

 *

 * So that all may benefit from your experience, please report  any  problems

 * or  suggestions about this software to the 29K Technical Support Center at

 * 800-29-29-AMD (800-292-9263) in the USA, or 0800-89-1131  in  the  UK,  or

 * 0031-11-1129 in Japan, toll free.  The direct dial number is 512-462-4118.

 *

 * Advanced Micro Devices, Inc.

 * 29K Support Products

 * Mail Stop 573

 * 5900 E. Ben White Blvd.

 * Austin, TX 78741

 * 800-292-9263

 *****************************************************************************

 *      Engineer: Srini Subramanian.

 *****************************************************************************

 **       This header file describes the errors which may be returned

 **       by the monitor.

 **

 **       All of the #define'ed error codes below begin with the leters

 **       "EM" (for "Error Monitor").  This should avoid colisions with

 **       other #define's in the system.

 **

 *****************************************************************************

 */

#ifndef _ERROR_H_INCLUDED_

#define _ERROR_H_INCLUDED_

/* General errors */

#define EMUSAGE     1  /* Bad args / flags               */

#define EMFAIL      2  /* Unrecoverable error            */

#define EMBADADDR   3  /* Illegal address                */

#define EMBADREG    4  /* Illegal register               */

#define EMSYNTAX    5  /* Illegal command syntax         */

#define EMACCESS    6  /* Could not access memory        */

#define EMALLOC     7  /* Could not allocate memory      */

#define EMTARGET    8  /* Unknown target type            */

#define EMHINIT     9  /* Could not initialize host      */

#define EMCOMM     10  /* Could not open communication channel */

/* Message errors */

#define EMBADMSG   11  /* Unknown message type           */

#define EMMSG2BIG  12  /* Message to large for buffer    */

#define EMRESET    13  /* Could not RESET target         */

#define EMCONFIG   14  /* Could not get target CONFIG    */

#define EMSTATUS   15  /* Could not get target STATUS    */

#define EMREAD     16  /* Could not READ target memory   */

#define EMWRITE    17  /* Could not WRITE target memory  */

#define EMBKPTSET  18  /* Could not set breakpoint       */

#define EMBKPTRM   19  /* Could not remove breakpoint    */

#define EMBKPTSTAT 20  /* Could not get breakpoint status */

#define EMBKPTNONE 21  /* All breakpoints in use         */

#define EMBKPTUSED 22  /* Breakpoints already in use     */

#define EMCOPY     23  /* Could not COPY target memory   */

#define EMFILL     24  /* Could not FILL target memory   */

#define EMINIT     25  /* Could not initialize target memory */

#define EMGO       26  /* Could not start execution      */

#define EMSTEP     27  /* Could not single step          */

#define EMBREAK    28  /* Could not BREAK                */

#define EMHIF      29  /* Could not perform HIF service  */

#define EMCHANNEL0 30  /* Could not read CHANNEL0        */

#define EMCHANNEL1 31  /* Could not write CHANNEL1       */

/* COFF file loader errors */

#define EMOPEN     32  /* Could not open COFF file       */

#define EMHDR      33  /* Could not read COFF header     */

#define EMMAGIC    34  /* Bad magic number               */

#define EMAOUT     35  /* Could not read COFF a.out header */

#define EMSCNHDR   36  /* Could not read COFF section header */

#define EMSCN      37  /* Could not read COFF section    */

#define EMCLOSE    38  /* Could not close COFF file      */

/* Log file errors */

#define EMLOGOPEN  39  /* Could not open log file        */

#define EMLOGREAD  40  /* Could not read log file        */

#define EMLOGWRITE 41  /* Could not write to log file    */

#define EMLOGCLOSE 42  /* Could not close log file       */

/* Command file errors */

#define EMCMDOPEN  43  /* Could not open command file    */

#define EMCMDREAD  44  /* Could not read command file    */

#define EMCMDWRITE 45  /* Could not write to command file */

#define EMCMDCLOSE 46  /* Could not close comand file    */

#define EMTIMEOUT  47  /* Host timed out waiting for a message */

#define EMCOMMTYPE 48  /* A '-t' flag must be specified  */

#define EMCOMMERR  49  /* Communication error            */

#define EMBAUD     50  /* Invalid baud rate specified    */

#define EMTIPINIT  51  /* Failed TIP init */

#define EMIOSETF   52  /* I/O set up failure */

#define EMIORESETF 53  /* I/O reset failure */

#define EMLOADF    54  /* Loading COFF file failed */

#define EMNOFILE   55   /* No program to run. */

#define EMECHOPEN  56   /* Could not open echo file */

#define EMCTRLC    57  /* Ctrl-C encountered */

#define EMNOSUCHCMD     58      /* Unrecognized command */

#define EMNOPROCESS     59   /* create process */

#define EMNOTCOMP       60      /* Not compatible */

#define EMFATAL         61   /* UDIWait failed */

#define EMNOINITP       62      /* No initialize process */

#define EMDOSERR        63      /* DOS err on escape */

#define EMSYSERR        64      /* system err on escape */

#define EMINVECHOFILE   65      /* invalid echo file */

#define EMCMDFILENEST   66      /* command file nesting */

extern  char *error_msg[];

#endif /* _ERROR_H_INCLUDED_ */