Subversion Repositories or1k

#include <linux/config.h>

#define PCILYNX_DRIVER_NAME      "pcilynx"

#define PCILYNX_MAJOR            177

#define PCILYNX_MINOR_AUX_START  0

#define PCILYNX_MINOR_ROM_START  16

#define PCILYNX_MINOR_RAM_START  32

#define PCILYNX_MAX_REGISTER     0xfff

#define PCILYNX_MAX_MEMORY       0xffff

#define PCI_DEVICE_ID_TI_PCILYNX 0x8000

#define MAX_PCILYNX_CARDS        4

#define LOCALRAM_SIZE            4096

#define NUM_ISORCV_PCL           4

#define MAX_ISORCV_SIZE          2048

#define ISORCV_PER_PAGE          (PAGE_SIZE / MAX_ISORCV_SIZE)

#define ISORCV_PAGES             (NUM_ISORCV_PCL / ISORCV_PER_PAGE)

#define CHANNEL_LOCALBUS         0

#define CHANNEL_ASYNC_RCV        1

#define CHANNEL_ISO_RCV          2

#define CHANNEL_ASYNC_SEND       3

#define CHANNEL_ISO_SEND         4

#define PCILYNX_CONFIG_ROM_LENGTH   1024

typedef int pcl_t;

struct ti_lynx {

        int id; /* sequential card number */

        spinlock_t lock;

        struct pci_dev *dev;

        struct {

                unsigned reg_1394a:1;

                u32 vendor;

                u32 product;

        } phyic;

        enum { clear, have_intr, have_aux_buf, have_pcl_mem,

               have_1394_buffers, have_iomappings, is_host } state;

        /* remapped memory spaces */

        void *registers;

        void *local_rom;

        void *local_ram;

        void *aux_port;

        quadlet_t config_rom[PCILYNX_CONFIG_ROM_LENGTH/4];

#ifdef CONFIG_IEEE1394_PCILYNX_PORTS

        atomic_t aux_intr_seen;

        wait_queue_head_t aux_intr_wait;

        void *mem_dma_buffer;

        dma_addr_t mem_dma_buffer_dma;

        struct semaphore mem_dma_mutex;

        wait_queue_head_t mem_dma_intr_wait;

#endif

        /*

         * use local RAM of LOCALRAM_SIZE bytes for PCLs, which allows for

         * LOCALRAM_SIZE * 8 PCLs (each sized 128 bytes);

         * the following is an allocation bitmap

         */

        u8 pcl_bmap[LOCALRAM_SIZE / 1024];

#ifndef CONFIG_IEEE1394_PCILYNX_LOCALRAM

        /* point to PCLs memory area if needed */

        void *pcl_mem;

        dma_addr_t pcl_mem_dma;

#endif

        /* PCLs for local mem / aux transfers */

        pcl_t dmem_pcl;

        /* IEEE-1394 part follows */

        struct hpsb_host *host;

        int phyid, isroot;

        int selfid_size;

        int phy_reg0;

        spinlock_t phy_reg_lock;

        pcl_t rcv_pcl_start, rcv_pcl;

        void *rcv_page;

        dma_addr_t rcv_page_dma;

        int rcv_active;

        struct lynx_send_data {

                pcl_t pcl_start, pcl;

                struct list_head queue;

                struct list_head pcl_queue; /* this queue contains at most one packet */

                spinlock_t queue_lock;

                dma_addr_t header_dma, data_dma;

                int channel;

        } async, iso_send;

        struct {

                pcl_t pcl[NUM_ISORCV_PCL];

                u32 stat[NUM_ISORCV_PCL];

                void *page[ISORCV_PAGES];

                dma_addr_t page_dma[ISORCV_PAGES];

                pcl_t pcl_start;

                int chan_count;

                int next, last, used, running;

                struct tasklet_struct tq;

                spinlock_t lock;

        } iso_rcv;

        u32 i2c_driven_state; /* the state we currently drive the Serial EEPROM Control register */

};

/* the per-file data structure for mem space access */

struct memdata {

        struct ti_lynx *lynx;

        int cid;

        atomic_t aux_intr_last_seen;

        /* enum values are the same as LBUS_ADDR_SEL_* values below */

        enum { rom = 0x10000, aux = 0x20000, ram = 0 } type;

};

/*

 * Register read and write helper functions.

 */

static inline void reg_write(const struct ti_lynx *lynx, int offset, u32 data)

{

        writel(data, lynx->registers + offset);

}

static inline u32 reg_read(const struct ti_lynx *lynx, int offset)

{

        return readl(lynx->registers + offset);

}

static inline void reg_set_bits(const struct ti_lynx *lynx, int offset,

                                u32 mask)

{

        reg_write(lynx, offset, (reg_read(lynx, offset) | mask));

}

static inline void reg_clear_bits(const struct ti_lynx *lynx, int offset,

                                  u32 mask)

{

        reg_write(lynx, offset, (reg_read(lynx, offset) & ~mask));

}

/* chip register definitions follow */

#define PCI_LATENCY_CACHELINE             0x0c

#define MISC_CONTROL                      0x40

#define MISC_CONTROL_SWRESET              (1<<0)

#define SERIAL_EEPROM_CONTROL             0x44

#define PCI_INT_STATUS                    0x48

#define PCI_INT_ENABLE                    0x4c               

/* status and enable have identical bit numbers */

#define PCI_INT_INT_PEND                  (1<<31)

#define PCI_INT_FORCED_INT                (1<<30)

#define PCI_INT_SLV_ADR_PERR              (1<<28)

#define PCI_INT_SLV_DAT_PERR              (1<<27)

#define PCI_INT_MST_DAT_PERR              (1<<26)

#define PCI_INT_MST_DEV_TIMEOUT           (1<<25)

#define PCI_INT_INTERNAL_SLV_TIMEOUT      (1<<23)

#define PCI_INT_AUX_TIMEOUT               (1<<18)

#define PCI_INT_AUX_INT                   (1<<17)

#define PCI_INT_1394                      (1<<16)

#define PCI_INT_DMA4_PCL                  (1<<9)

#define PCI_INT_DMA4_HLT                  (1<<8)

#define PCI_INT_DMA3_PCL                  (1<<7)

#define PCI_INT_DMA3_HLT                  (1<<6)

#define PCI_INT_DMA2_PCL                  (1<<5)

#define PCI_INT_DMA2_HLT                  (1<<4)

#define PCI_INT_DMA1_PCL                  (1<<3)

#define PCI_INT_DMA1_HLT                  (1<<2)

#define PCI_INT_DMA0_PCL                  (1<<1)

#define PCI_INT_DMA0_HLT                  (1<<0)

/* all DMA interrupts combined: */

#define PCI_INT_DMA_ALL                   0x3ff

#define PCI_INT_DMA_HLT(chan)             (1 << (chan * 2))

#define PCI_INT_DMA_PCL(chan)             (1 << (chan * 2 + 1))

#define LBUS_ADDR                         0xb4

#define LBUS_ADDR_SEL_RAM                 (0x0<<16)

#define LBUS_ADDR_SEL_ROM                 (0x1<<16)

#define LBUS_ADDR_SEL_AUX                 (0x2<<16)

#define LBUS_ADDR_SEL_ZV                  (0x3<<16)       

#define GPIO_CTRL_A                       0xb8

#define GPIO_CTRL_B                       0xbc

#define GPIO_DATA_BASE                    0xc0

#define DMA_BREG(base, chan)              (base + chan * 0x20)

#define DMA_SREG(base, chan)              (base + chan * 0x10)

#define DMA0_PREV_PCL                     0x100               

#define DMA1_PREV_PCL                     0x120

#define DMA2_PREV_PCL                     0x140

#define DMA3_PREV_PCL                     0x160

#define DMA4_PREV_PCL                     0x180

#define DMA_PREV_PCL(chan)                (DMA_BREG(DMA0_PREV_PCL, chan))

#define DMA0_CURRENT_PCL                  0x104            

#define DMA1_CURRENT_PCL                  0x124

#define DMA2_CURRENT_PCL                  0x144

#define DMA3_CURRENT_PCL                  0x164

#define DMA4_CURRENT_PCL                  0x184

#define DMA_CURRENT_PCL(chan)             (DMA_BREG(DMA0_CURRENT_PCL, chan))

#define DMA0_CHAN_STAT                    0x10c

#define DMA1_CHAN_STAT                    0x12c

#define DMA2_CHAN_STAT                    0x14c

#define DMA3_CHAN_STAT                    0x16c

#define DMA4_CHAN_STAT                    0x18c

#define DMA_CHAN_STAT(chan)               (DMA_BREG(DMA0_CHAN_STAT, chan))

/* CHAN_STATUS registers share bits */

#define DMA_CHAN_STAT_SELFID              (1<<31)

#define DMA_CHAN_STAT_ISOPKT              (1<<30)

#define DMA_CHAN_STAT_PCIERR              (1<<29)

#define DMA_CHAN_STAT_PKTERR              (1<<28)

#define DMA_CHAN_STAT_PKTCMPL             (1<<27)

#define DMA_CHAN_STAT_SPECIALACK          (1<<14)

#define DMA0_CHAN_CTRL                    0x110              

#define DMA1_CHAN_CTRL                    0x130

#define DMA2_CHAN_CTRL                    0x150

#define DMA3_CHAN_CTRL                    0x170

#define DMA4_CHAN_CTRL                    0x190

#define DMA_CHAN_CTRL(chan)               (DMA_BREG(DMA0_CHAN_CTRL, chan))

/* CHAN_CTRL registers share bits */

#define DMA_CHAN_CTRL_ENABLE              (1<<31)      

#define DMA_CHAN_CTRL_BUSY                (1<<30)

#define DMA_CHAN_CTRL_LINK                (1<<29)

#define DMA0_READY                        0x114

#define DMA1_READY                        0x134

#define DMA2_READY                        0x154

#define DMA3_READY                        0x174

#define DMA4_READY                        0x194

#define DMA_READY(chan)                   (DMA_BREG(DMA0_READY, chan))

#define DMA_GLOBAL_REGISTER               0x908

#define FIFO_SIZES                        0xa00

#define FIFO_CONTROL                      0xa10

#define FIFO_CONTROL_GRF_FLUSH            (1<<4)

#define FIFO_CONTROL_ITF_FLUSH            (1<<3)

#define FIFO_CONTROL_ATF_FLUSH            (1<<2)

#define FIFO_XMIT_THRESHOLD               0xa14

#define DMA0_WORD0_CMP_VALUE              0xb00

#define DMA1_WORD0_CMP_VALUE              0xb10

#define DMA2_WORD0_CMP_VALUE              0xb20

#define DMA3_WORD0_CMP_VALUE              0xb30

#define DMA4_WORD0_CMP_VALUE              0xb40

#define DMA_WORD0_CMP_VALUE(chan)         (DMA_SREG(DMA0_WORD0_CMP_VALUE, chan))

#define DMA0_WORD0_CMP_ENABLE             0xb04

#define DMA1_WORD0_CMP_ENABLE             0xb14

#define DMA2_WORD0_CMP_ENABLE             0xb24

#define DMA3_WORD0_CMP_ENABLE             0xb34

#define DMA4_WORD0_CMP_ENABLE             0xb44

#define DMA_WORD0_CMP_ENABLE(chan)        (DMA_SREG(DMA0_WORD0_CMP_ENABLE,chan))

#define DMA0_WORD1_CMP_VALUE              0xb08

#define DMA1_WORD1_CMP_VALUE              0xb18

#define DMA2_WORD1_CMP_VALUE              0xb28

#define DMA3_WORD1_CMP_VALUE              0xb38

#define DMA4_WORD1_CMP_VALUE              0xb48

#define DMA_WORD1_CMP_VALUE(chan)         (DMA_SREG(DMA0_WORD1_CMP_VALUE, chan))

#define DMA0_WORD1_CMP_ENABLE             0xb0c

#define DMA1_WORD1_CMP_ENABLE             0xb1c

#define DMA2_WORD1_CMP_ENABLE             0xb2c

#define DMA3_WORD1_CMP_ENABLE             0xb3c

#define DMA4_WORD1_CMP_ENABLE             0xb4c

#define DMA_WORD1_CMP_ENABLE(chan)        (DMA_SREG(DMA0_WORD1_CMP_ENABLE,chan))

/* word 1 compare enable flags */

#define DMA_WORD1_CMP_MATCH_OTHERBUS      (1<<15)

#define DMA_WORD1_CMP_MATCH_BROADCAST     (1<<14)

#define DMA_WORD1_CMP_MATCH_BUS_BCAST     (1<<13)

#define DMA_WORD1_CMP_MATCH_LOCAL_NODE    (1<<12)

#define DMA_WORD1_CMP_MATCH_EXACT         (1<<11)

#define DMA_WORD1_CMP_ENABLE_SELF_ID      (1<<10)

#define DMA_WORD1_CMP_ENABLE_MASTER       (1<<8)

#define LINK_ID                           0xf00

#define LINK_ID_BUS(id)                   (id<<22)

#define LINK_ID_NODE(id)                  (id<<16)

#define LINK_CONTROL                      0xf04

#define LINK_CONTROL_BUSY                 (1<<29)

#define LINK_CONTROL_TX_ISO_EN            (1<<26)

#define LINK_CONTROL_RX_ISO_EN            (1<<25)

#define LINK_CONTROL_TX_ASYNC_EN          (1<<24)

#define LINK_CONTROL_RX_ASYNC_EN          (1<<23)

#define LINK_CONTROL_RESET_TX             (1<<21)

#define LINK_CONTROL_RESET_RX             (1<<20)

#define LINK_CONTROL_CYCMASTER            (1<<11)

#define LINK_CONTROL_CYCSOURCE            (1<<10)

#define LINK_CONTROL_CYCTIMEREN           (1<<9)

#define LINK_CONTROL_RCV_CMP_VALID        (1<<7)

#define LINK_CONTROL_SNOOP_ENABLE         (1<<6)

#define CYCLE_TIMER                       0xf08

#define LINK_PHY                          0xf0c

#define LINK_PHY_READ                     (1<<31)

#define LINK_PHY_WRITE                    (1<<30)

#define LINK_PHY_ADDR(addr)               (addr<<24)

#define LINK_PHY_WDATA(data)              (data<<16)

#define LINK_PHY_RADDR(addr)              (addr<<8)

#define LINK_INT_STATUS                   0xf14

#define LINK_INT_ENABLE                   0xf18

/* status and enable have identical bit numbers */

#define LINK_INT_LINK_INT                 (1<<31)

#define LINK_INT_PHY_TIMEOUT              (1<<30)

#define LINK_INT_PHY_REG_RCVD             (1<<29)

#define LINK_INT_PHY_BUSRESET             (1<<28)

#define LINK_INT_TX_RDY                   (1<<26)

#define LINK_INT_RX_DATA_RDY              (1<<25)

#define LINK_INT_ISO_STUCK                (1<<20)

#define LINK_INT_ASYNC_STUCK              (1<<19)

#define LINK_INT_SENT_REJECT              (1<<17)

#define LINK_INT_HDR_ERR                  (1<<16)

#define LINK_INT_TX_INVALID_TC            (1<<15)

#define LINK_INT_CYC_SECOND               (1<<11)

#define LINK_INT_CYC_START                (1<<10)

#define LINK_INT_CYC_DONE                 (1<<9)

#define LINK_INT_CYC_PENDING              (1<<8)

#define LINK_INT_CYC_LOST                 (1<<7)

#define LINK_INT_CYC_ARB_FAILED           (1<<6)

#define LINK_INT_GRF_OVERFLOW             (1<<5)

#define LINK_INT_ITF_UNDERFLOW            (1<<4)

#define LINK_INT_ATF_UNDERFLOW            (1<<3)

#define LINK_INT_ISOARB_FAILED            (1<<0) 

/* PHY specifics */

#define PHY_VENDORID_TI                 0x800028

#define PHY_PRODUCTID_TSB41LV03         0x000000

/* this is the physical layout of a PCL, its size is 128 bytes */

struct ti_pcl {

        u32 next;

        u32 async_error_next;

        u32 user_data;

        u32 pcl_status;

        u32 remaining_transfer_count;

        u32 next_data_buffer;

        struct {

                u32 control;

                u32 pointer;

        } buffer[13] __attribute__ ((packed));

} __attribute__ ((packed));

#include <linux/stddef.h>

#define pcloffs(MEMBER) (offsetof(struct ti_pcl, MEMBER))

#ifdef CONFIG_IEEE1394_PCILYNX_LOCALRAM

static inline void put_pcl(const struct ti_lynx *lynx, pcl_t pclid,

                           const struct ti_pcl *pcl)

{

        int i;

        u32 *in = (u32 *)pcl;

        u32 *out = (u32 *)(lynx->local_ram + pclid * sizeof(struct ti_pcl));

        for (i = 0; i < 32; i++, out++, in++) {

                writel(*in, out);

        }

}

static inline void get_pcl(const struct ti_lynx *lynx, pcl_t pclid,

                           struct ti_pcl *pcl)

{

        int i;

        u32 *out = (u32 *)pcl;

        u32 *in = (u32 *)(lynx->local_ram + pclid * sizeof(struct ti_pcl));

        for (i = 0; i < 32; i++, out++, in++) {

                *out = readl(in);

        }

}

static inline u32 pcl_bus(const struct ti_lynx *lynx, pcl_t pclid)

{

        return pci_resource_start(lynx->dev, 1) + pclid * sizeof(struct ti_pcl);

}

#else /* CONFIG_IEEE1394_PCILYNX_LOCALRAM */

static inline void put_pcl(const struct ti_lynx *lynx, pcl_t pclid,

                           const struct ti_pcl *pcl)

{

        memcpy_le32((u32 *)(lynx->pcl_mem + pclid * sizeof(struct ti_pcl)),

                    (u32 *)pcl, sizeof(struct ti_pcl));

}

static inline void get_pcl(const struct ti_lynx *lynx, pcl_t pclid,

                           struct ti_pcl *pcl)

{

        memcpy_le32((u32 *)pcl,

                    (u32 *)(lynx->pcl_mem + pclid * sizeof(struct ti_pcl)),

                    sizeof(struct ti_pcl));

}

static inline u32 pcl_bus(const struct ti_lynx *lynx, pcl_t pclid)

{

        return lynx->pcl_mem_dma + pclid * sizeof(struct ti_pcl);

}

#endif /* CONFIG_IEEE1394_PCILYNX_LOCALRAM */

#if defined (CONFIG_IEEE1394_PCILYNX_LOCALRAM) || defined (__BIG_ENDIAN)

typedef struct ti_pcl pcltmp_t;

static inline struct ti_pcl *edit_pcl(const struct ti_lynx *lynx, pcl_t pclid,

                                      pcltmp_t *tmp)

{

        get_pcl(lynx, pclid, tmp);

        return tmp;

}

static inline void commit_pcl(const struct ti_lynx *lynx, pcl_t pclid,

                              pcltmp_t *tmp)

{

        put_pcl(lynx, pclid, tmp);

}

#else

typedef int pcltmp_t; /* just a dummy */

static inline struct ti_pcl *edit_pcl(const struct ti_lynx *lynx, pcl_t pclid,

                                      pcltmp_t *tmp)

{

        return lynx->pcl_mem + pclid * sizeof(struct ti_pcl);

}

static inline void commit_pcl(const struct ti_lynx *lynx, pcl_t pclid,

                              pcltmp_t *tmp)

{

}

#endif

static inline void run_sub_pcl(const struct ti_lynx *lynx, pcl_t pclid, int idx,

                               int dmachan)

{

        reg_write(lynx, DMA0_CURRENT_PCL + dmachan * 0x20,

                  pcl_bus(lynx, pclid) + idx * 4);

        reg_write(lynx, DMA0_CHAN_CTRL + dmachan * 0x20,

                  DMA_CHAN_CTRL_ENABLE | DMA_CHAN_CTRL_LINK);

}

static inline void run_pcl(const struct ti_lynx *lynx, pcl_t pclid, int dmachan)

{

        run_sub_pcl(lynx, pclid, 0, dmachan);

}

#define PCL_NEXT_INVALID (1<<0)

/* transfer commands */

#define PCL_CMD_RCV            (0x1<<24)

#define PCL_CMD_RCV_AND_UPDATE (0xa<<24)

#define PCL_CMD_XMT            (0x2<<24)

#define PCL_CMD_UNFXMT         (0xc<<24)

#define PCL_CMD_PCI_TO_LBUS    (0x8<<24)

#define PCL_CMD_LBUS_TO_PCI    (0x9<<24)

/* aux commands */

#define PCL_CMD_NOP            (0x0<<24)

#define PCL_CMD_LOAD           (0x3<<24)

#define PCL_CMD_STOREQ         (0x4<<24)

#define PCL_CMD_STORED         (0xb<<24)

#define PCL_CMD_STORE0         (0x5<<24)

#define PCL_CMD_STORE1         (0x6<<24)

#define PCL_CMD_COMPARE        (0xe<<24)

#define PCL_CMD_SWAP_COMPARE   (0xf<<24)

#define PCL_CMD_ADD            (0xd<<24)

#define PCL_CMD_BRANCH         (0x7<<24)

/* BRANCH condition codes */

#define PCL_COND_DMARDY_SET    (0x1<<20)

#define PCL_COND_DMARDY_CLEAR  (0x2<<20)

#define PCL_GEN_INTR           (1<<19)

#define PCL_LAST_BUFF          (1<<18)

#define PCL_LAST_CMD           (PCL_LAST_BUFF)

#define PCL_WAITSTAT           (1<<17)

#define PCL_BIGENDIAN          (1<<16)

#define PCL_ISOMODE            (1<<12)

#define _(x) (__constant_cpu_to_be32(x))

static quadlet_t lynx_csr_rom[] = {

/* bus info block     offset (hex) */

        _(0x04046aaf), /* info/CRC length, CRC              400  */

        _(0x31333934), /* 1394 magic number                 404  */

        _(0xf064a000), /* misc. settings                    408  */

        _(0x08002850), /* vendor ID, chip ID high           40c  */

        _(0x0000ffff), /* chip ID low                       410  */

/* root directory */

        _(0x00095778), /* directory length, CRC             414  */

        _(0x03080028), /* vendor ID (Texas Instr.)          418  */

        _(0x81000008), /* offset to textual ID              41c  */

        _(0x0c000200), /* node capabilities                 420  */

        _(0x8d00000e), /* offset to unique ID               424  */

        _(0xc7000010), /* offset to module independent info 428  */

        _(0x04000000), /* module hardware version           42c  */

        _(0x81000014), /* offset to textual ID              430  */

        _(0x09000000), /* node hardware version             434  */

        _(0x81000018), /* offset to textual ID              438  */

/* module vendor ID textual */

        _(0x00070812), /* CRC length, CRC                   43c  */

        _(0x00000000), /*                                   440  */

        _(0x00000000), /*                                   444  */

        _(0x54455841), /* "Texas Instruments"               448  */

        _(0x5320494e), /*                                   44c  */

        _(0x53545255), /*                                   450  */

        _(0x4d454e54), /*                                   454  */

        _(0x53000000), /*                                   458  */

/* node unique ID leaf */

        _(0x00022ead), /* CRC length, CRC                   45c  */

        _(0x08002850), /* vendor ID, chip ID high           460  */

        _(0x0000ffff), /* chip ID low                       464  */

/* module dependent info */

        _(0x0005d837), /* CRC length, CRC                   468  */

        _(0x81000012), /* offset to module textual ID       46c  */

        _(0x81000017), /* textual descriptor                470  */

        _(0x39010000), /* SRAM size                         474  */

        _(0x3a010000), /* AUXRAM size                       478  */

        _(0x3b000000), /* AUX device                        47c  */

/* module textual ID */

        _(0x000594df), /* CRC length, CRC                   480  */

        _(0x00000000), /*                                   484  */

        _(0x00000000), /*                                   488  */

        _(0x54534231), /* "TSB12LV21"                       48c  */

        _(0x324c5632), /*                                   490  */

        _(0x31000000), /*                                   494  */

/* part number */

        _(0x00068405), /* CRC length, CRC                   498  */

        _(0x00000000), /*                                   49c  */

        _(0x00000000), /*                                   4a0  */

        _(0x39383036), /* "9806000-0001"                    4a4  */

        _(0x3030302d), /*                                   4a8  */

        _(0x30303031), /*                                   4ac  */

        _(0x20000001), /*                                   4b0  */

/* module hardware version textual */

        _(0x00056501), /* CRC length, CRC                   4b4  */

        _(0x00000000), /*                                   4b8  */

        _(0x00000000), /*                                   4bc  */

        _(0x5453424b), /* "TSBKPCITST"                      4c0  */

        _(0x50434954), /*                                   4c4  */

        _(0x53540000), /*                                   4c8  */

/* node hardware version textual */

        _(0x0005d805), /* CRC length, CRC                   4d0  */

        _(0x00000000), /*                                   4d4  */

        _(0x00000000), /*                                   4d8  */

        _(0x54534232), /* "TSB21LV03"                       4dc  */

        _(0x314c5630), /*                                   4e0  */

        _(0x33000000)  /*                                   4e4  */

};

#undef _