Subversion Repositories or1k

/*

 * macserial.h: Definitions for the Macintosh Z8530 serial driver.

 *

 * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.

 *

 * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)

 * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)

 */

#ifndef _MACSERIAL_H

#define _MACSERIAL_H

#define NUM_ZSREGS    16

struct serial_struct {

        int     type;

        int     line;

        int     port;

        int     irq;

        int     flags;

        int     xmit_fifo_size;

        int     custom_divisor;

        int     baud_base;

        unsigned short  close_delay;

        char    reserved_char[2];

        int     hub6;

        unsigned short  closing_wait; /* time to wait before closing */

        unsigned short  closing_wait2; /* no longer used... */

        int     reserved[4];

};

/*

 * For the close wait times, 0 means wait forever for serial port to

 * flush its output.  65535 means don't wait at all.

 */

#define ZILOG_CLOSING_WAIT_INF  0

#define ZILOG_CLOSING_WAIT_NONE 65535

/*

 * Definitions for ZILOG_struct (and serial_struct) flags field

 */

#define ZILOG_HUP_NOTIFY        0x0001  /* Notify getty on hangups and closes 

                                         * on the callout port */

#define ZILOG_FOURPORT          0x0002  /* Set OU1, OUT2 per AST Fourport settings */

#define ZILOG_SAK               0x0004  /* Secure Attention Key (Orange book) */

#define ZILOG_SPLIT_TERMIOS     0x0008  /* Separate termios for dialin/callout */

#define ZILOG_SPD_MASK          0x0030

#define ZILOG_SPD_HI            0x0010  /* Use 56000 instead of 38400 bps */

#define ZILOG_SPD_VHI           0x0020  /* Use 115200 instead of 38400 bps */

#define ZILOG_SPD_CUST          0x0030  /* Use user-specified divisor */

#define ZILOG_SKIP_TEST         0x0040  /* Skip UART test during autoconfiguration */

#define ZILOG_AUTO_IRQ          0x0080  /* Do automatic IRQ during autoconfiguration */

#define ZILOG_SESSION_LOCKOUT   0x0100  /* Lock out cua opens based on session */

#define ZILOG_PGRP_LOCKOUT      0x0200  /* Lock out cua opens based on pgrp */

#define ZILOG_CALLOUT_NOHUP     0x0400  /* Don't do hangups for cua device */

#define ZILOG_FLAGS             0x0FFF  /* Possible legal ZILOG flags */

#define ZILOG_USR_MASK          0x0430  /* Legal flags that non-privileged

                                         * users can set or reset */

/* Internal flags used only by kernel/chr_drv/serial.c */

#define ZILOG_INITIALIZED       0x80000000 /* Serial port was initialized */

#define ZILOG_CALLOUT_ACTIVE    0x40000000 /* Call out device is active */

#define ZILOG_NORMAL_ACTIVE     0x20000000 /* Normal device is active */

#define ZILOG_BOOT_AUTOCONF     0x10000000 /* Autoconfigure port on bootup */

#define ZILOG_CLOSING           0x08000000 /* Serial port is closing */

#define ZILOG_CTS_FLOW          0x04000000 /* Do CTS flow control */

#define ZILOG_CHECK_CD          0x02000000 /* i.e., CLOCAL */

#define ZILOG_SLEEPING          0x01000000 /* have shut it down for sleep */

/* Software state per channel */

#ifdef __KERNEL__

/*

 * This is our internal structure for each serial port's state.

 *

 * Many fields are paralleled by the structure used by the serial_struct

 * structure.

 *

 * For definitions of the flags field, see tty.h

 */

struct mac_serial;

struct mac_zschannel {

        volatile unsigned char* control;

        volatile unsigned char* data;

        spinlock_t              lock;

        /* Used for debugging */

        struct mac_serial*      parent;

};

struct mac_dma {

        volatile struct dbdma_regs      dma;

        volatile unsigned short         res_count;

        volatile unsigned short         command;

        volatile unsigned int           buf_addr;

};

struct mac_serial {

        struct mac_serial *zs_next;     /* For IRQ servicing chain */

        struct mac_zschannel *zs_channel; /* Channel registers */

        struct mac_zschannel *zs_chan_a;        /* A side registers */

        unsigned char read_reg_zero;

        struct device_node* dev_node;

        char soft_carrier;  /* Use soft carrier on this channel */

        char break_abort;   /* Is serial console in, so process brk/abrt */

        char kgdb_channel;  /* Kgdb is running on this channel */

        char is_cons;       /* Is this our console. */

        char is_internal_modem; /* is connected to an internal modem */

        char is_irda;           /* is connected to an IrDA codec */

        int port_type;          /* Port type for pmac_feature */

        unsigned char tx_active; /* character is being xmitted */

        unsigned char tx_stopped; /* output is suspended */

        unsigned char power_wait; /* waiting for power-up delay to expire */

        /* We need to know the current clock divisor

         * to read the bps rate the chip has currently

         * loaded.

         */

        unsigned char clk_divisor;  /* May be 1, 16, 32, or 64 */

        int zs_baud;

        /* Current write register values */

        unsigned char curregs[NUM_ZSREGS];

        /* Values we need to set next opportunity */

        unsigned char pendregs[NUM_ZSREGS];

        char change_needed;

        int                     magic;

        int                     baud_base;

        int                     port;

        int                     irq;

        int                     flags;          /* defined in tty.h */

        int                     type;           /* UART type */

        struct tty_struct       *tty;

        int                     read_status_mask;

        int                     ignore_status_mask;

        int                     timeout;

        int                     xmit_fifo_size;

        int                     custom_divisor;

        int                     x_char; /* xon/xoff character */

        int                     close_delay;

        unsigned short          closing_wait;

        unsigned short          closing_wait2;

        unsigned long           event;

        unsigned long           last_active;

        int                     line;

        int                     count;      /* # of fd on device */

        int                     blocked_open; /* # of blocked opens */

        long                    session; /* Session of opening process */

        long                    pgrp; /* pgrp of opening process */

        unsigned char           *xmit_buf;

        int                     xmit_head;

        int                     xmit_tail;

        int                     xmit_cnt;

        struct tq_struct        tqueue;

        struct tq_struct        tqueue_hangup;

        struct termios          normal_termios;

        struct termios          callout_termios;

        wait_queue_head_t       open_wait;

        wait_queue_head_t       close_wait;

        volatile struct dbdma_regs *tx_dma;

        int                     tx_dma_irq;

        volatile struct dbdma_cmd *tx_cmds;

        volatile struct mac_dma *rx;

        int                     rx_dma_irq;

        volatile struct dbdma_cmd **rx_cmds;

        unsigned char           **rx_char_buf;

        unsigned char           **rx_flag_buf;

#define RX_BUF_SIZE     256

        int                     rx_nbuf;

        int                     rx_done_bytes;

        int                     rx_ubuf;

        int                     rx_fbuf;

#define RX_NO_FBUF      (-1)

        int                     rx_cbuf;

        spinlock_t              rx_dma_lock;

        int                     has_dma;

        int                     dma_initted;

        void                    *dma_priv;

        struct timer_list       poll_dma_timer;

#define RX_DMA_TIMER    (jiffies + 10*HZ/1000)

        struct timer_list       powerup_timer;

};

#define SERIAL_MAGIC 0x5301

/*

 * The size of the serial xmit buffer is 1 page, or 4096 bytes

 */

#define SERIAL_XMIT_SIZE 4096

/*

 * Events are used to schedule things to happen at timer-interrupt

 * time, instead of at rs interrupt time.

 */

#define RS_EVENT_WRITE_WAKEUP   0

#endif /* __KERNEL__ */

/* Conversion routines to/from brg time constants from/to bits

 * per second.

 */

#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))

#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)

/* The Zilog register set */

#define FLAG    0x7e

/* Write Register 0 */

#define R0      0                /* Register selects */

#define R1      1

#define R2      2

#define R3      3

#define R4      4

#define R5      5

#define R6      6

#define R7      7

#define R8      8

#define R9      9

#define R10     10

#define R11     11

#define R12     12

#define R13     13

#define R14     14

#define R15     15

#define NULLCODE        0        /* Null Code */

#define POINT_HIGH      0x8     /* Select upper half of registers */

#define RES_EXT_INT     0x10    /* Reset Ext. Status Interrupts */

#define SEND_ABORT      0x18    /* HDLC Abort */

#define RES_RxINT_FC    0x20    /* Reset RxINT on First Character */

#define RES_Tx_P        0x28    /* Reset TxINT Pending */

#define ERR_RES         0x30    /* Error Reset */

#define RES_H_IUS       0x38    /* Reset highest IUS */

#define RES_Rx_CRC      0x40    /* Reset Rx CRC Checker */

#define RES_Tx_CRC      0x80    /* Reset Tx CRC Checker */

#define RES_EOM_L       0xC0    /* Reset EOM latch */

/* Write Register 1 */

#define EXT_INT_ENAB    0x1     /* Ext Int Enable */

#define TxINT_ENAB      0x2     /* Tx Int Enable */

#define PAR_SPEC        0x4     /* Parity is special condition */

#define RxINT_DISAB     0        /* Rx Int Disable */

#define RxINT_FCERR     0x8     /* Rx Int on First Character Only or Error */

#define INT_ALL_Rx      0x10    /* Int on all Rx Characters or error */

#define INT_ERR_Rx      0x18    /* Int on error only */

#define WT_RDY_RT       0x20    /* W/Req reflects recv if 1, xmit if 0 */

#define WT_FN_RDYFN     0x40    /* W/Req pin is DMA request if 1, wait if 0 */

#define WT_RDY_ENAB     0x80    /* Enable W/Req pin */

/* Write Register #2 (Interrupt Vector) */

/* Write Register 3 */

#define RxENABLE        0x1     /* Rx Enable */

#define SYNC_L_INH      0x2     /* Sync Character Load Inhibit */

#define ADD_SM          0x4     /* Address Search Mode (SDLC) */

#define RxCRC_ENAB      0x8     /* Rx CRC Enable */

#define ENT_HM          0x10    /* Enter Hunt Mode */

#define AUTO_ENAB       0x20    /* Auto Enables */

#define Rx5             0x0     /* Rx 5 Bits/Character */

#define Rx7             0x40    /* Rx 7 Bits/Character */

#define Rx6             0x80    /* Rx 6 Bits/Character */

#define Rx8             0xc0    /* Rx 8 Bits/Character */

#define RxNBITS_MASK    0xc0

/* Write Register 4 */

#define PAR_ENA         0x1     /* Parity Enable */

#define PAR_EVEN        0x2     /* Parity Even/Odd* */

#define SYNC_ENAB       0        /* Sync Modes Enable */

#define SB1             0x4     /* 1 stop bit/char */

#define SB15            0x8     /* 1.5 stop bits/char */

#define SB2             0xc     /* 2 stop bits/char */

#define SB_MASK         0xc

#define MONSYNC         0        /* 8 Bit Sync character */

#define BISYNC          0x10    /* 16 bit sync character */

#define SDLC            0x20    /* SDLC Mode (01111110 Sync Flag) */

#define EXTSYNC         0x30    /* External Sync Mode */

#define X1CLK           0x0     /* x1 clock mode */

#define X16CLK          0x40    /* x16 clock mode */

#define X32CLK          0x80    /* x32 clock mode */

#define X64CLK          0xC0    /* x64 clock mode */

#define XCLK_MASK       0xC0

/* Write Register 5 */

#define TxCRC_ENAB      0x1     /* Tx CRC Enable */

#define RTS             0x2     /* RTS */

#define SDLC_CRC        0x4     /* SDLC/CRC-16 */

#define TxENAB          0x8     /* Tx Enable */

#define SND_BRK         0x10    /* Send Break */

#define Tx5             0x0     /* Tx 5 bits (or less)/character */

#define Tx7             0x20    /* Tx 7 bits/character */

#define Tx6             0x40    /* Tx 6 bits/character */

#define Tx8             0x60    /* Tx 8 bits/character */

#define TxNBITS_MASK    0x60

#define DTR             0x80    /* DTR */

/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */

/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */

/* Write Register 7' (Some enhanced feature control) */

#define ENEXREAD        0x40    /* Enable read of some write registers */

/* Write Register 8 (transmit buffer) */

/* Write Register 9 (Master interrupt control) */

#define VIS     1       /* Vector Includes Status */

#define NV      2       /* No Vector */

#define DLC     4       /* Disable Lower Chain */

#define MIE     8       /* Master Interrupt Enable */

#define STATHI  0x10    /* Status high */

#define NORESET 0        /* No reset on write to R9 */

#define CHRB    0x40    /* Reset channel B */

#define CHRA    0x80    /* Reset channel A */

#define FHWRES  0xc0    /* Force hardware reset */

/* Write Register 10 (misc control bits) */

#define BIT6    1       /* 6 bit/8bit sync */

#define LOOPMODE 2      /* SDLC Loop mode */

#define ABUNDER 4       /* Abort/flag on SDLC xmit underrun */

#define MARKIDLE 8      /* Mark/flag on idle */

#define GAOP    0x10    /* Go active on poll */

#define NRZ     0        /* NRZ mode */

#define NRZI    0x20    /* NRZI mode */

#define FM1     0x40    /* FM1 (transition = 1) */

#define FM0     0x60    /* FM0 (transition = 0) */

#define CRCPS   0x80    /* CRC Preset I/O */

/* Write Register 11 (Clock Mode control) */

#define TRxCXT  0        /* TRxC = Xtal output */

#define TRxCTC  1       /* TRxC = Transmit clock */

#define TRxCBR  2       /* TRxC = BR Generator Output */

#define TRxCDP  3       /* TRxC = DPLL output */

#define TRxCOI  4       /* TRxC O/I */

#define TCRTxCP 0        /* Transmit clock = RTxC pin */

#define TCTRxCP 8       /* Transmit clock = TRxC pin */

#define TCBR    0x10    /* Transmit clock = BR Generator output */

#define TCDPLL  0x18    /* Transmit clock = DPLL output */

#define RCRTxCP 0        /* Receive clock = RTxC pin */

#define RCTRxCP 0x20    /* Receive clock = TRxC pin */

#define RCBR    0x40    /* Receive clock = BR Generator output */

#define RCDPLL  0x60    /* Receive clock = DPLL output */

#define RTxCX   0x80    /* RTxC Xtal/No Xtal */

/* Write Register 12 (lower byte of baud rate generator time constant) */

/* Write Register 13 (upper byte of baud rate generator time constant) */

/* Write Register 14 (Misc control bits) */

#define BRENABL 1       /* Baud rate generator enable */

#define BRSRC   2       /* Baud rate generator source */

#define DTRREQ  4       /* DTR/Request function */

#define AUTOECHO 8      /* Auto Echo */

#define LOOPBAK 0x10    /* Local loopback */

#define SEARCH  0x20    /* Enter search mode */

#define RMC     0x40    /* Reset missing clock */

#define DISDPLL 0x60    /* Disable DPLL */

#define SSBR    0x80    /* Set DPLL source = BR generator */

#define SSRTxC  0xa0    /* Set DPLL source = RTxC */

#define SFMM    0xc0    /* Set FM mode */

#define SNRZI   0xe0    /* Set NRZI mode */

/* Write Register 15 (external/status interrupt control) */

#define EN85C30 1       /* Enable some 85c30-enhanced registers */

#define ZCIE    2       /* Zero count IE */

#define ENSTFIFO 4      /* Enable status FIFO (SDLC) */

#define DCDIE   8       /* DCD IE */

#define SYNCIE  0x10    /* Sync/hunt IE */

#define CTSIE   0x20    /* CTS IE */

#define TxUIE   0x40    /* Tx Underrun/EOM IE */

#define BRKIE   0x80    /* Break/Abort IE */

/* Read Register 0 */

#define Rx_CH_AV        0x1     /* Rx Character Available */

#define ZCOUNT          0x2     /* Zero count */

#define Tx_BUF_EMP      0x4     /* Tx Buffer empty */

#define DCD             0x8     /* DCD */

#define SYNC_HUNT       0x10    /* Sync/hunt */

#define CTS             0x20    /* CTS */

#define TxEOM           0x40    /* Tx underrun */

#define BRK_ABRT        0x80    /* Break/Abort */

/* Read Register 1 */

#define ALL_SNT         0x1     /* All sent */

/* Residue Data for 8 Rx bits/char programmed */

#define RES3            0x8     /* 0/3 */

#define RES4            0x4     /* 0/4 */

#define RES5            0xc     /* 0/5 */

#define RES6            0x2     /* 0/6 */

#define RES7            0xa     /* 0/7 */

#define RES8            0x6     /* 0/8 */

#define RES18           0xe     /* 1/8 */

#define RES28           0x0     /* 2/8 */

/* Special Rx Condition Interrupts */

#define PAR_ERR         0x10    /* Parity error */

#define Rx_OVR          0x20    /* Rx Overrun Error */

#define FRM_ERR         0x40    /* CRC/Framing Error */

#define END_FR          0x80    /* End of Frame (SDLC) */

/* Read Register 2 (channel b only) - Interrupt vector */

#define CHB_Tx_EMPTY    0x00

#define CHB_EXT_STAT    0x02

#define CHB_Rx_AVAIL    0x04

#define CHB_SPECIAL     0x06

#define CHA_Tx_EMPTY    0x08

#define CHA_EXT_STAT    0x0a

#define CHA_Rx_AVAIL    0x0c

#define CHA_SPECIAL     0x0e

#define STATUS_MASK     0x06

/* Read Register 3 (interrupt pending register) ch a only */

#define CHBEXT  0x1             /* Channel B Ext/Stat IP */

#define CHBTxIP 0x2             /* Channel B Tx IP */

#define CHBRxIP 0x4             /* Channel B Rx IP */

#define CHAEXT  0x8             /* Channel A Ext/Stat IP */

#define CHATxIP 0x10            /* Channel A Tx IP */

#define CHARxIP 0x20            /* Channel A Rx IP */

/* Read Register 8 (receive data register) */

/* Read Register 10  (misc status bits) */

#define ONLOOP  2               /* On loop */

#define LOOPSEND 0x10           /* Loop sending */

#define CLK2MIS 0x40            /* Two clocks missing */

#define CLK1MIS 0x80            /* One clock missing */

/* Read Register 12 (lower byte of baud rate generator constant) */

/* Read Register 13 (upper byte of baud rate generator constant) */

/* Read Register 15 (value of WR 15) */

/* Misc macros */

#define ZS_CLEARERR(channel)    (write_zsreg(channel, 0, ERR_RES))

#define ZS_CLEARFIFO(channel)   do { volatile unsigned char garbage; \

                                     garbage = read_zsdata(channel); \

                                     garbage = read_zsdata(channel); \

                                     garbage = read_zsdata(channel); \

                                } while(0)

#endif /* !(_MACSERIAL_H) */