URL https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k

[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [parport/] [parport_pc.c] - Blame information for rev 1765

Details | Compare with Previous | View Log

/* Low-level parallel-port routines for 8255-based PC-style hardware.
 *
 * Authors: Phil Blundell <Philip.Blundell@pobox.com>
 *          Tim Waugh <tim@cyberelk.demon.co.uk>
 *          Jose Renau <renau@acm.org>
 *          David Campbell <campbell@torque.net>
 *          Andrea Arcangeli
 *
 * based on work by Grant Guenther <grant@torque.net> and Phil Blundell.
 *
 * Cleaned up include files - Russell King <linux@arm.uk.linux.org>
 * DMA support - Bert De Jonghe <bert@sophis.be>
 * Many ECP bugs fixed.  Fred Barnes & Jamie Lokier, 1999
 * More PCI support now conditional on CONFIG_PCI, 03/2001, Paul G.
 * Various hacks, Fred Barnes, 04/2001
 */
 
/* This driver should work with any hardware that is broadly compatible
 * with that in the IBM PC.  This applies to the majority of integrated
 * I/O chipsets that are commonly available.  The expected register
 * layout is:
 *
 *      base+0          data
 *      base+1          status
 *      base+2          control
 *
 * In addition, there are some optional registers:
 *
 *      base+3          EPP address
 *      base+4          EPP data
 *      base+0x400      ECP config A
 *      base+0x401      ECP config B
 *      base+0x402      ECP control
 *
 * All registers are 8 bits wide and read/write.  If your hardware differs
 * only in register addresses (eg because your registers are on 32-bit
 * word boundaries) then you can alter the constants in parport_pc.h to
 * accomodate this.
 *
 * Note that the ECP registers may not start at offset 0x400 for PCI cards,
 * but rather will start at port->base_hi.
 */
 
#include <linux/config.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/sysctl.h>
 
#include <asm/io.h>
#include <asm/dma.h>
#include <asm/uaccess.h>
 
#include <linux/parport.h>
#include <linux/parport_pc.h>
#include <asm/parport.h>
 
#define PARPORT_PC_MAX_PORTS PARPORT_MAX
 
/* ECR modes */
#define ECR_SPP 00
#define ECR_PS2 01
#define ECR_PPF 02
#define ECR_ECP 03
#define ECR_EPP 04
#define ECR_VND 05
#define ECR_TST 06
#define ECR_CNF 07
#define ECR_MODE_MASK 0xe0
#define ECR_WRITE(p,v) frob_econtrol((p),0xff,(v))
 
#undef DEBUG
 
#ifdef DEBUG
#define DPRINTK  printk
#else
#define DPRINTK(stuff...)
#endif
 
 
#define NR_SUPERIOS 3
static struct superio_struct {  /* For Super-IO chips autodetection */
        int io;
        int irq;
        int dma;
} superios[NR_SUPERIOS] __devinitdata = { {0,},};
 
static int user_specified __devinitdata = 0;
#if defined(CONFIG_PARPORT_PC_FIFO) || defined(CONFIG_PARPORT_PC_SUPERIO)
static int verbose_probing;
#endif
static int registered_parport;
 
/* frob_control, but for ECR */
static void frob_econtrol (struct parport *pb, unsigned char m,
                           unsigned char v)
{
        unsigned char ectr = 0;
 
        if (m != 0xff)
                ectr = inb (ECONTROL (pb));
 
        DPRINTK (KERN_DEBUG "frob_econtrol(%02x,%02x): %02x -> %02x\n",
                m, v, ectr, (ectr & ~m) ^ v);
 
        outb ((ectr & ~m) ^ v, ECONTROL (pb));
}
 
static void __inline__ frob_set_mode (struct parport *p, int mode)
{
        frob_econtrol (p, ECR_MODE_MASK, mode << 5);
}
 
#ifdef CONFIG_PARPORT_PC_FIFO
/* Safely change the mode bits in the ECR
   Returns:
 
           -EBUSY: Could not drain FIFO in some finite amount of time,
                   mode not changed!
 */
static int change_mode(struct parport *p, int m)
{
        const struct parport_pc_private *priv = p->physport->private_data;
        unsigned char oecr;
        int mode;
 
        DPRINTK(KERN_INFO "parport change_mode ECP-ISA to mode 0x%02x\n",m);
 
        if (!priv->ecr) {
                printk (KERN_DEBUG "change_mode: but there's no ECR!\n");
                return 0;
        }
 
        /* Bits <7:5> contain the mode. */
        oecr = inb (ECONTROL (p));
        mode = (oecr >> 5) & 0x7;
        if (mode == m) return 0;
 
        if (mode >= 2 && !(priv->ctr & 0x20)) {
                /* This mode resets the FIFO, so we may
                 * have to wait for it to drain first. */
                long expire = jiffies + p->physport->cad->timeout;
                int counter;
                switch (mode) {
                case ECR_PPF: /* Parallel Port FIFO mode */
                case ECR_ECP: /* ECP Parallel Port mode */
                        /* Busy wait for 200us */
                        for (counter = 0; counter < 40; counter++) {
                                if (inb (ECONTROL (p)) & 0x01)
                                        break;
                                if (signal_pending (current)) break;
                                udelay (5);
                        }
 
                        /* Poll slowly. */
                        while (!(inb (ECONTROL (p)) & 0x01)) {
                                if (time_after_eq (jiffies, expire))
                                        /* The FIFO is stuck. */
                                        return -EBUSY;
                                __set_current_state (TASK_INTERRUPTIBLE);
                                schedule_timeout ((HZ + 99) / 100);
                                if (signal_pending (current))
                                        break;
                        }
                }
        }
 
        if (mode >= 2 && m >= 2) {
                /* We have to go through mode 001 */
                oecr &= ~(7 << 5);
                oecr |= ECR_PS2 << 5;
                ECR_WRITE (p, oecr);
        }
 
        /* Set the mode. */
        oecr &= ~(7 << 5);
        oecr |= m << 5;
        ECR_WRITE (p, oecr);
        return 0;
}
 
#ifdef CONFIG_PARPORT_1284
/* Find FIFO lossage; FIFO is reset */
static int get_fifo_residue (struct parport *p)
{
        int residue;
        int cnfga;
        const struct parport_pc_private *priv = p->physport->private_data;
 
        /* Adjust for the contents of the FIFO. */
        for (residue = priv->fifo_depth; ; residue--) {
                if (inb (ECONTROL (p)) & 0x2)
                                /* Full up. */
                        break;
 
                outb (0, FIFO (p));
        }
 
        printk (KERN_DEBUG "%s: %d PWords were left in FIFO\n", p->name,
                residue);
 
        /* Reset the FIFO. */
        frob_set_mode (p, ECR_PS2);
 
        /* Now change to config mode and clean up. FIXME */
        frob_set_mode (p, ECR_CNF);
        cnfga = inb (CONFIGA (p));
        printk (KERN_DEBUG "%s: cnfgA contains 0x%02x\n", p->name, cnfga);
 
        if (!(cnfga & (1<<2))) {
                printk (KERN_DEBUG "%s: Accounting for extra byte\n", p->name);
                residue++;
        }
 
        /* Don't care about partial PWords until support is added for
         * PWord != 1 byte. */
 
        /* Back to PS2 mode. */
        frob_set_mode (p, ECR_PS2);
 
        DPRINTK (KERN_DEBUG "*** get_fifo_residue: done residue collecting (ecr = 0x%2.2x)\n", inb (ECONTROL (p)));
        return residue;
}
#endif /* IEEE 1284 support */
#endif /* FIFO support */
 
/*
 * Clear TIMEOUT BIT in EPP MODE
 *
 * This is also used in SPP detection.
 */
static int clear_epp_timeout(struct parport *pb)
{
        unsigned char r;
 
        if (!(parport_pc_read_status(pb) & 0x01))
                return 1;
 
        /* To clear timeout some chips require double read */
        parport_pc_read_status(pb);
        r = parport_pc_read_status(pb);
        outb (r | 0x01, STATUS (pb)); /* Some reset by writing 1 */
        outb (r & 0xfe, STATUS (pb)); /* Others by writing 0 */
        r = parport_pc_read_status(pb);
 
        return !(r & 0x01);
}
 
/*
 * Access functions.
 *
 * Most of these aren't static because they may be used by the
 * parport_xxx_yyy macros.  extern __inline__ versions of several
 * of these are in parport_pc.h.
 */
 
static void parport_pc_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
        parport_generic_irq(irq, (struct parport *) dev_id, regs);
}
 
void parport_pc_write_data(struct parport *p, unsigned char d)
{
        outb (d, DATA (p));
}
 
unsigned char parport_pc_read_data(struct parport *p)
{
        return inb (DATA (p));
}
 
void parport_pc_write_control(struct parport *p, unsigned char d)
{
        const unsigned char wm = (PARPORT_CONTROL_STROBE |
                                  PARPORT_CONTROL_AUTOFD |
                                  PARPORT_CONTROL_INIT |
                                  PARPORT_CONTROL_SELECT);
 
        /* Take this out when drivers have adapted to the newer interface. */
        if (d & 0x20) {
                printk (KERN_DEBUG "%s (%s): use data_reverse for this!\n",
                        p->name, p->cad->name);
                parport_pc_data_reverse (p);
        }
 
        __parport_pc_frob_control (p, wm, d & wm);
}
 
unsigned char parport_pc_read_control(struct parport *p)
{
        const unsigned char wm = (PARPORT_CONTROL_STROBE |
                                  PARPORT_CONTROL_AUTOFD |
                                  PARPORT_CONTROL_INIT |
                                  PARPORT_CONTROL_SELECT);
        const struct parport_pc_private *priv = p->physport->private_data;
        return priv->ctr & wm; /* Use soft copy */
}
 
unsigned char parport_pc_frob_control (struct parport *p, unsigned char mask,
                                       unsigned char val)
{
        const unsigned char wm = (PARPORT_CONTROL_STROBE |
                                  PARPORT_CONTROL_AUTOFD |
                                  PARPORT_CONTROL_INIT |
                                  PARPORT_CONTROL_SELECT);
 
        /* Take this out when drivers have adapted to the newer interface. */
        if (mask & 0x20) {
                printk (KERN_DEBUG "%s (%s): use data_%s for this!\n",
                        p->name, p->cad->name,
                        (val & 0x20) ? "reverse" : "forward");
                if (val & 0x20)
                        parport_pc_data_reverse (p);
                else
                        parport_pc_data_forward (p);
        }
 
        /* Restrict mask and val to control lines. */
        mask &= wm;
        val &= wm;
 
        return __parport_pc_frob_control (p, mask, val);
}
 
unsigned char parport_pc_read_status(struct parport *p)
{
        return inb (STATUS (p));
}
 
void parport_pc_disable_irq(struct parport *p)
{
        __parport_pc_frob_control (p, 0x10, 0);
}
 
void parport_pc_enable_irq(struct parport *p)
{
        if (p->irq != PARPORT_IRQ_NONE)
                __parport_pc_frob_control (p, 0x10, 0x10);
}
 
void parport_pc_data_forward (struct parport *p)
{
        __parport_pc_frob_control (p, 0x20, 0);
}
 
void parport_pc_data_reverse (struct parport *p)
{
        __parport_pc_frob_control (p, 0x20, 0x20);
}
 
void parport_pc_init_state(struct pardevice *dev, struct parport_state *s)
{
        s->u.pc.ctr = 0xc;
        if (dev->irq_func &&
            dev->port->irq != PARPORT_IRQ_NONE)
                /* Set ackIntEn */
                s->u.pc.ctr |= 0x10;
 
        s->u.pc.ecr = 0x34; /* NetMos chip can cause problems 0x24;
                             * D.Gruszka VScom */
}
 
void parport_pc_save_state(struct parport *p, struct parport_state *s)
{
        const struct parport_pc_private *priv = p->physport->private_data;
        s->u.pc.ctr = priv->ctr;
        if (priv->ecr)
                s->u.pc.ecr = inb (ECONTROL (p));
}
 
void parport_pc_restore_state(struct parport *p, struct parport_state *s)
{
        struct parport_pc_private *priv = p->physport->private_data;
        register unsigned char c = s->u.pc.ctr & priv->ctr_writable;
        outb (c, CONTROL (p));
        priv->ctr = c;
        if (priv->ecr)
                ECR_WRITE (p, s->u.pc.ecr);
}
 
#ifdef CONFIG_PARPORT_1284
static size_t parport_pc_epp_read_data (struct parport *port, void *buf,
                                        size_t length, int flags)
{
        size_t got = 0;
 
        if (flags & PARPORT_W91284PIC) {
                unsigned char status;
                size_t left = length;
 
                /* use knowledge about data lines..:
                 *  nFault is 0 if there is at least 1 byte in the Warp's FIFO
                 *  pError is 1 if there are 16 bytes in the Warp's FIFO
                 */
                status = inb (STATUS (port));
 
                while (!(status & 0x08) && (got < length)) {
                        if ((left >= 16) && (status & 0x20) && !(status & 0x08)) {
                                /* can grab 16 bytes from warp fifo */
                                if (!((long)buf & 0x03)) {
                                        insl (EPPDATA (port), buf, 4);
                                } else {
                                        insb (EPPDATA (port), buf, 16);
                                }
                                buf += 16;
                                got += 16;
                                left -= 16;
                        } else {
                                /* grab single byte from the warp fifo */
                                *((char *)buf)++ = inb (EPPDATA (port));
                                got++;
                                left--;
                        }
                        status = inb (STATUS (port));
                        if (status & 0x01) {
                                /* EPP timeout should never occur... */
                                printk (KERN_DEBUG "%s: EPP timeout occured while talking to "
                                        "w91284pic (should not have done)\n", port->name);
                                clear_epp_timeout (port);
                        }
                }
                return got;
        }
        if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
                if (!(((long)buf | length) & 0x03)) {
                        insl (EPPDATA (port), buf, (length >> 2));
                } else {
                        insb (EPPDATA (port), buf, length);
                }
                if (inb (STATUS (port)) & 0x01) {
                        clear_epp_timeout (port);
                        return -EIO;
                }
                return length;
        }
        for (; got < length; got++) {
                *((char*)buf)++ = inb (EPPDATA(port));
                if (inb (STATUS (port)) & 0x01) {
                        /* EPP timeout */
                        clear_epp_timeout (port);
                        break;
                }
        }
 
        return got;
}
 
static size_t parport_pc_epp_write_data (struct parport *port, const void *buf,
                                         size_t length, int flags)
{
        size_t written = 0;
 
        if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
                if (!(((long)buf | length) & 0x03)) {
                        outsl (EPPDATA (port), buf, (length >> 2));
                } else {
                        outsb (EPPDATA (port), buf, length);
                }
                if (inb (STATUS (port)) & 0x01) {
                        clear_epp_timeout (port);
                        return -EIO;
                }
                return length;
        }
        for (; written < length; written++) {
                outb (*((char*)buf)++, EPPDATA(port));
                if (inb (STATUS(port)) & 0x01) {
                        clear_epp_timeout (port);
                        break;
                }
        }
 
        return written;
}
 
static size_t parport_pc_epp_read_addr (struct parport *port, void *buf,
                                        size_t length, int flags)
{
        size_t got = 0;
 
        if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
                insb (EPPADDR (port), buf, length);
                if (inb (STATUS (port)) & 0x01) {
                        clear_epp_timeout (port);
                        return -EIO;
                }
                return length;
        }
        for (; got < length; got++) {
                *((char*)buf)++ = inb (EPPADDR (port));
                if (inb (STATUS (port)) & 0x01) {
                        clear_epp_timeout (port);
                        break;
                }
        }
 
        return got;
}
 
static size_t parport_pc_epp_write_addr (struct parport *port,
                                         const void *buf, size_t length,
                                         int flags)
{
        size_t written = 0;
 
        if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
                outsb (EPPADDR (port), buf, length);
                if (inb (STATUS (port)) & 0x01) {
                        clear_epp_timeout (port);
                        return -EIO;
                }
                return length;
        }
        for (; written < length; written++) {
                outb (*((char*)buf)++, EPPADDR (port));
                if (inb (STATUS (port)) & 0x01) {
                        clear_epp_timeout (port);
                        break;
                }
        }
 
        return written;
}
 
static size_t parport_pc_ecpepp_read_data (struct parport *port, void *buf,
                                           size_t length, int flags)
{
        size_t got;
 
        frob_set_mode (port, ECR_EPP);
        parport_pc_data_reverse (port);
        parport_pc_write_control (port, 0x4);
        got = parport_pc_epp_read_data (port, buf, length, flags);
        frob_set_mode (port, ECR_PS2);
 
        return got;
}
 
static size_t parport_pc_ecpepp_write_data (struct parport *port,
                                            const void *buf, size_t length,
                                            int flags)
{
        size_t written;
 
        frob_set_mode (port, ECR_EPP);
        parport_pc_write_control (port, 0x4);
        parport_pc_data_forward (port);
        written = parport_pc_epp_write_data (port, buf, length, flags);
        frob_set_mode (port, ECR_PS2);
 
        return written;
}
 
static size_t parport_pc_ecpepp_read_addr (struct parport *port, void *buf,
                                           size_t length, int flags)
{
        size_t got;
 
        frob_set_mode (port, ECR_EPP);
        parport_pc_data_reverse (port);
        parport_pc_write_control (port, 0x4);
        got = parport_pc_epp_read_addr (port, buf, length, flags);
        frob_set_mode (port, ECR_PS2);
 
        return got;
}
 
static size_t parport_pc_ecpepp_write_addr (struct parport *port,
                                            const void *buf, size_t length,
                                            int flags)
{
        size_t written;
 
        frob_set_mode (port, ECR_EPP);
        parport_pc_write_control (port, 0x4);
        parport_pc_data_forward (port);
        written = parport_pc_epp_write_addr (port, buf, length, flags);
        frob_set_mode (port, ECR_PS2);
 
        return written;
}
#endif /* IEEE 1284 support */
 
#ifdef CONFIG_PARPORT_PC_FIFO
static size_t parport_pc_fifo_write_block_pio (struct parport *port,
                                               const void *buf, size_t length)
{
        int ret = 0;
        const unsigned char *bufp = buf;
        size_t left = length;
        long expire = jiffies + port->physport->cad->timeout;
        const int fifo = FIFO (port);
        int poll_for = 8; /* 80 usecs */
        const struct parport_pc_private *priv = port->physport->private_data;
        const int fifo_depth = priv->fifo_depth;
 
        port = port->physport;
 
        /* We don't want to be interrupted every character. */
        parport_pc_disable_irq (port);
        /* set nErrIntrEn and serviceIntr */
        frob_econtrol (port, (1<<4) | (1<<2), (1<<4) | (1<<2));
 
        /* Forward mode. */
        parport_pc_data_forward (port); /* Must be in PS2 mode */
 
        while (left) {
                unsigned char byte;
                unsigned char ecrval = inb (ECONTROL (port));
                int i = 0;
 
                if (current->need_resched && time_before (jiffies, expire))
                        /* Can't yield the port. */
                        schedule ();
 
                /* Anyone else waiting for the port? */
                if (port->waithead) {
                        printk (KERN_DEBUG "Somebody wants the port\n");
                        break;
                }
 
                if (ecrval & 0x02) {
                        /* FIFO is full. Wait for interrupt. */
 
                        /* Clear serviceIntr */
                        ECR_WRITE (port, ecrval & ~(1<<2));
                false_alarm:
                        ret = parport_wait_event (port, HZ);
                        if (ret < 0) break;
                        ret = 0;
                        if (!time_before (jiffies, expire)) {
                                /* Timed out. */
                                printk (KERN_DEBUG "FIFO write timed out\n");
                                break;
                        }
                        ecrval = inb (ECONTROL (port));
                        if (!(ecrval & (1<<2))) {
                                if (current->need_resched &&
                                    time_before (jiffies, expire))
                                        schedule ();
 
                                goto false_alarm;
                        }
 
                        continue;
                }
 
                /* Can't fail now. */
                expire = jiffies + port->cad->timeout;
 
        poll:
                if (signal_pending (current))
                        break;
 
                if (ecrval & 0x01) {
                        /* FIFO is empty. Blast it full. */
                        const int n = left < fifo_depth ? left : fifo_depth;
                        outsb (fifo, bufp, n);
                        bufp += n;
                        left -= n;
 
                        /* Adjust the poll time. */
                        if (i < (poll_for - 2)) poll_for--;
                        continue;
                } else if (i++ < poll_for) {
                        udelay (10);
                        ecrval = inb (ECONTROL (port));
                        goto poll;
                }
 
                /* Half-full (call me an optimist) */
                byte = *bufp++;
                outb (byte, fifo);
                left--;
        }
 
dump_parport_state ("leave fifo_write_block_pio", port);
        return length - left;
}
 
static size_t parport_pc_fifo_write_block_dma (struct parport *port,
                                               const void *buf, size_t length)
{
        int ret = 0;
        unsigned long dmaflag;
        size_t left = length;
        const struct parport_pc_private *priv = port->physport->private_data;
        dma_addr_t dma_addr, dma_handle;
        size_t maxlen = 0x10000; /* max 64k per DMA transfer */
        unsigned long start = (unsigned long) buf;
        unsigned long end = (unsigned long) buf + length - 1;
 
dump_parport_state ("enter fifo_write_block_dma", port);
        if (end < MAX_DMA_ADDRESS) {
                /* If it would cross a 64k boundary, cap it at the end. */
                if ((start ^ end) & ~0xffffUL)
                        maxlen = 0x10000 - (start & 0xffff);
 
                dma_addr = dma_handle = pci_map_single(priv->dev, (void *)buf, length,
                                                       PCI_DMA_TODEVICE);
        } else {
                /* above 16 MB we use a bounce buffer as ISA-DMA is not possible */
                maxlen   = PAGE_SIZE;          /* sizeof(priv->dma_buf) */
                dma_addr = priv->dma_handle;
                dma_handle = 0;
        }
 
        port = port->physport;
 
        /* We don't want to be interrupted every character. */
        parport_pc_disable_irq (port);
        /* set nErrIntrEn and serviceIntr */
        frob_econtrol (port, (1<<4) | (1<<2), (1<<4) | (1<<2));
 
        /* Forward mode. */
        parport_pc_data_forward (port); /* Must be in PS2 mode */
 
        while (left) {
                long expire = jiffies + port->physport->cad->timeout;
 
                size_t count = left;
 
                if (count > maxlen)
                        count = maxlen;
 
                if (!dma_handle)   /* bounce buffer ! */
                        memcpy(priv->dma_buf, buf, count);
 
                dmaflag = claim_dma_lock();
                disable_dma(port->dma);
                clear_dma_ff(port->dma);
                set_dma_mode(port->dma, DMA_MODE_WRITE);
                set_dma_addr(port->dma, dma_addr);
                set_dma_count(port->dma, count);
 
                /* Set DMA mode */
                frob_econtrol (port, 1<<3, 1<<3);
 
                /* Clear serviceIntr */
                frob_econtrol (port, 1<<2, 0);
 
                enable_dma(port->dma);
                release_dma_lock(dmaflag);
 
                /* assume DMA will be successful */
                left -= count;
                buf  += count;
                if (dma_handle) dma_addr += count;
 
                /* Wait for interrupt. */
        false_alarm:
                ret = parport_wait_event (port, HZ);
                if (ret < 0) break;
                ret = 0;
                if (!time_before (jiffies, expire)) {
                        /* Timed out. */
                        printk (KERN_DEBUG "DMA write timed out\n");
                        break;
                }
                /* Is serviceIntr set? */
                if (!(inb (ECONTROL (port)) & (1<<2))) {
                        if (current->need_resched)
                                schedule ();
 
                        goto false_alarm;
                }
 
                dmaflag = claim_dma_lock();
                disable_dma(port->dma);
                clear_dma_ff(port->dma);
                count = get_dma_residue(port->dma);
                release_dma_lock(dmaflag);
 
                if (current->need_resched)
                        /* Can't yield the port. */
                        schedule ();
 
                /* Anyone else waiting for the port? */
                if (port->waithead) {
                        printk (KERN_DEBUG "Somebody wants the port\n");
                        break;
                }
 
                /* update for possible DMA residue ! */
                buf  -= count;
                left += count;
                if (dma_handle) dma_addr -= count;
        }
 
        /* Maybe got here through break, so adjust for DMA residue! */
        dmaflag = claim_dma_lock();
        disable_dma(port->dma);
        clear_dma_ff(port->dma);
        left += get_dma_residue(port->dma);
        release_dma_lock(dmaflag);
 
        /* Turn off DMA mode */
        frob_econtrol (port, 1<<3, 0);
 
        if (dma_handle)
                pci_unmap_single(priv->dev, dma_handle, length, PCI_DMA_TODEVICE);
 
dump_parport_state ("leave fifo_write_block_dma", port);
        return length - left;
}
 
/* Parallel Port FIFO mode (ECP chipsets) */
size_t parport_pc_compat_write_block_pio (struct parport *port,
                                          const void *buf, size_t length,
                                          int flags)
{
        size_t written;
        int r;
        long int expire;
        const struct parport_pc_private *priv = port->physport->private_data;
 
        /* Special case: a timeout of zero means we cannot call schedule().
         * Also if O_NONBLOCK is set then use the default implementation. */
        if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
                return parport_ieee1284_write_compat (port, buf,
                                                      length, flags);
 
        /* Set up parallel port FIFO mode.*/
        parport_pc_data_forward (port); /* Must be in PS2 mode */
        parport_pc_frob_control (port, PARPORT_CONTROL_STROBE, 0);
        r = change_mode (port, ECR_PPF); /* Parallel port FIFO */
        if (r)  printk (KERN_DEBUG "%s: Warning change_mode ECR_PPF failed\n", port->name);
 
        port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
 
        /* Write the data to the FIFO. */
        if (port->dma != PARPORT_DMA_NONE)
                written = parport_pc_fifo_write_block_dma (port, buf, length);
        else
                written = parport_pc_fifo_write_block_pio (port, buf, length);
 
        /* Finish up. */
        /* For some hardware we don't want to touch the mode until
         * the FIFO is empty, so allow 4 seconds for each position
         * in the fifo.
         */
        expire = jiffies + (priv->fifo_depth * HZ * 4);
        do {
                /* Wait for the FIFO to empty */
                r = change_mode (port, ECR_PS2);
                if (r != -EBUSY) {
                        break;
                }
        } while (time_before (jiffies, expire));
        if (r == -EBUSY) {
 
                printk (KERN_DEBUG "%s: FIFO is stuck\n", port->name);
 
                /* Prevent further data transfer. */
                frob_set_mode (port, ECR_TST);
 
                /* Adjust for the contents of the FIFO. */
                for (written -= priv->fifo_depth; ; written++) {
                        if (inb (ECONTROL (port)) & 0x2) {
                                /* Full up. */
                                break;
                        }
                        outb (0, FIFO (port));
                }
 
                /* Reset the FIFO and return to PS2 mode. */
                frob_set_mode (port, ECR_PS2);
        }
 
        r = parport_wait_peripheral (port,
                                     PARPORT_STATUS_BUSY,
                                     PARPORT_STATUS_BUSY);
        if (r)
                printk (KERN_DEBUG
                        "%s: BUSY timeout (%d) in compat_write_block_pio\n",
                        port->name, r);
 
        port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
 
        return written;
}
 
/* ECP */
#ifdef CONFIG_PARPORT_1284
size_t parport_pc_ecp_write_block_pio (struct parport *port,
                                       const void *buf, size_t length,
                                       int flags)
{
        size_t written;
        int r;
        long int expire;
        const struct parport_pc_private *priv = port->physport->private_data;
 
        /* Special case: a timeout of zero means we cannot call schedule().
         * Also if O_NONBLOCK is set then use the default implementation. */
        if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
                return parport_ieee1284_ecp_write_data (port, buf,
                                                        length, flags);
 
        /* Switch to forward mode if necessary. */
        if (port->physport->ieee1284.phase != IEEE1284_PH_FWD_IDLE) {
                /* Event 47: Set nInit high. */
                parport_frob_control (port,
                                      PARPORT_CONTROL_INIT
                                      | PARPORT_CONTROL_AUTOFD,
                                      PARPORT_CONTROL_INIT
                                      | PARPORT_CONTROL_AUTOFD);
 
                /* Event 49: PError goes high. */
                r = parport_wait_peripheral (port,
                                             PARPORT_STATUS_PAPEROUT,
                                             PARPORT_STATUS_PAPEROUT);
                if (r) {
                        printk (KERN_DEBUG "%s: PError timeout (%d) "
                                "in ecp_write_block_pio\n", port->name, r);
                }
        }
 
        /* Set up ECP parallel port mode.*/
        parport_pc_data_forward (port); /* Must be in PS2 mode */
        parport_pc_frob_control (port,
                                 PARPORT_CONTROL_STROBE |
                                 PARPORT_CONTROL_AUTOFD,
                                 0);
        r = change_mode (port, ECR_ECP); /* ECP FIFO */
        if (r) printk (KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n", port->name);
        port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
 
        /* Write the data to the FIFO. */
        if (port->dma != PARPORT_DMA_NONE)
                written = parport_pc_fifo_write_block_dma (port, buf, length);
        else
                written = parport_pc_fifo_write_block_pio (port, buf, length);
 
        /* Finish up. */
        /* For some hardware we don't want to touch the mode until
         * the FIFO is empty, so allow 4 seconds for each position
         * in the fifo.
         */
        expire = jiffies + (priv->fifo_depth * (HZ * 4));
        do {
                /* Wait for the FIFO to empty */
                r = change_mode (port, ECR_PS2);
                if (r != -EBUSY) {
                        break;
                }
        } while (time_before (jiffies, expire));
        if (r == -EBUSY) {
 
                printk (KERN_DEBUG "%s: FIFO is stuck\n", port->name);
 
                /* Prevent further data transfer. */
                frob_set_mode (port, ECR_TST);
 
                /* Adjust for the contents of the FIFO. */
                for (written -= priv->fifo_depth; ; written++) {
                        if (inb (ECONTROL (port)) & 0x2) {
                                /* Full up. */
                                break;
                        }
                        outb (0, FIFO (port));
                }
 
                /* Reset the FIFO and return to PS2 mode. */
                frob_set_mode (port, ECR_PS2);
 
                /* Host transfer recovery. */
                parport_pc_data_reverse (port); /* Must be in PS2 mode */
                udelay (5);
                parport_frob_control (port, PARPORT_CONTROL_INIT, 0);
                r = parport_wait_peripheral (port, PARPORT_STATUS_PAPEROUT, 0);
                if (r)
                        printk (KERN_DEBUG "%s: PE,1 timeout (%d) "
                                "in ecp_write_block_pio\n", port->name, r);
 
                parport_frob_control (port,
                                      PARPORT_CONTROL_INIT,
                                      PARPORT_CONTROL_INIT);
                r = parport_wait_peripheral (port,
                                             PARPORT_STATUS_PAPEROUT,
                                             PARPORT_STATUS_PAPEROUT);
                if (r)
                        printk (KERN_DEBUG "%s: PE,2 timeout (%d) "
                                "in ecp_write_block_pio\n", port->name, r);
        }
 
        r = parport_wait_peripheral (port,
                                     PARPORT_STATUS_BUSY,
                                     PARPORT_STATUS_BUSY);
        if(r)
                printk (KERN_DEBUG
                        "%s: BUSY timeout (%d) in ecp_write_block_pio\n",
                        port->name, r);
 
        port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
 
        return written;
}
 
size_t parport_pc_ecp_read_block_pio (struct parport *port,
                                      void *buf, size_t length, int flags)
{
        size_t left = length;
        size_t fifofull;
        int r;
        const int fifo = FIFO(port);
        const struct parport_pc_private *priv = port->physport->private_data;
        const int fifo_depth = priv->fifo_depth;
        char *bufp = buf;
 
        port = port->physport;
DPRINTK (KERN_DEBUG "parport_pc: parport_pc_ecp_read_block_pio\n");
dump_parport_state ("enter fcn", port);
 
        /* Special case: a timeout of zero means we cannot call schedule().
         * Also if O_NONBLOCK is set then use the default implementation. */
        if (port->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
                return parport_ieee1284_ecp_read_data (port, buf,
                                                       length, flags);
 
        if (port->ieee1284.mode == IEEE1284_MODE_ECPRLE) {
                /* If the peripheral is allowed to send RLE compressed
                 * data, it is possible for a byte to expand to 128
                 * bytes in the FIFO. */
                fifofull = 128;
        } else {
                fifofull = fifo_depth;
        }
 
        /* If the caller wants less than a full FIFO's worth of data,
         * go through software emulation.  Otherwise we may have to throw
         * away data. */
        if (length < fifofull)
                return parport_ieee1284_ecp_read_data (port, buf,
                                                       length, flags);
 
        if (port->ieee1284.phase != IEEE1284_PH_REV_IDLE) {
                /* change to reverse-idle phase (must be in forward-idle) */
 
                /* Event 38: Set nAutoFd low (also make sure nStrobe is high) */
                parport_frob_control (port,
                                      PARPORT_CONTROL_AUTOFD
                                      | PARPORT_CONTROL_STROBE,
                                      PARPORT_CONTROL_AUTOFD);
                parport_pc_data_reverse (port); /* Must be in PS2 mode */
                udelay (5);
                /* Event 39: Set nInit low to initiate bus reversal */
                parport_frob_control (port,
                                      PARPORT_CONTROL_INIT,
                                      0);
                /* Event 40: Wait for  nAckReverse (PError) to go low */
                r = parport_wait_peripheral (port, PARPORT_STATUS_PAPEROUT, 0);
                if (r) {
                        printk (KERN_DEBUG "%s: PE timeout Event 40 (%d) "
                                "in ecp_read_block_pio\n", port->name, r);
                        return 0;
                }
        }
 
        /* Set up ECP FIFO mode.*/
/*      parport_pc_frob_control (port,
                                 PARPORT_CONTROL_STROBE |
                                 PARPORT_CONTROL_AUTOFD,
                                 PARPORT_CONTROL_AUTOFD); */
        r = change_mode (port, ECR_ECP); /* ECP FIFO */
        if (r) printk (KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n", port->name);
 
        port->ieee1284.phase = IEEE1284_PH_REV_DATA;
 
        /* the first byte must be collected manually */
dump_parport_state ("pre 43", port);
        /* Event 43: Wait for nAck to go low */
        r = parport_wait_peripheral (port, PARPORT_STATUS_ACK, 0);
        if (r) {
                /* timed out while reading -- no data */
                printk (KERN_DEBUG "PIO read timed out (initial byte)\n");
                goto out_no_data;
        }
        /* read byte */
        *bufp++ = inb (DATA (port));
        left--;
dump_parport_state ("43-44", port);
        /* Event 44: nAutoFd (HostAck) goes high to acknowledge */
        parport_pc_frob_control (port,
                                 PARPORT_CONTROL_AUTOFD,
                                 0);
dump_parport_state ("pre 45", port);
        /* Event 45: Wait for nAck to go high */
/*      r = parport_wait_peripheral (port, PARPORT_STATUS_ACK, PARPORT_STATUS_ACK); */
dump_parport_state ("post 45", port);
r = 0;
        if (r) {
                /* timed out while waiting for peripheral to respond to ack */
                printk (KERN_DEBUG "ECP PIO read timed out (waiting for nAck)\n");
 
                /* keep hold of the byte we've got already */
                goto out_no_data;
        }
        /* Event 46: nAutoFd (HostAck) goes low to accept more data */
        parport_pc_frob_control (port,
                                 PARPORT_CONTROL_AUTOFD,
                                 PARPORT_CONTROL_AUTOFD);
 
 
dump_parport_state ("rev idle", port);
        /* Do the transfer. */
        while (left > fifofull) {
                int ret;
                long int expire = jiffies + port->cad->timeout;
                unsigned char ecrval = inb (ECONTROL (port));
 
                if (current->need_resched && time_before (jiffies, expire))
                        /* Can't yield the port. */
                        schedule ();
 
                /* At this point, the FIFO may already be full. In
                 * that case ECP is already holding back the
                 * peripheral (assuming proper design) with a delayed
                 * handshake.  Work fast to avoid a peripheral
                 * timeout.  */
 
                if (ecrval & 0x01) {
                        /* FIFO is empty. Wait for interrupt. */
dump_parport_state ("FIFO empty", port);
 
                        /* Anyone else waiting for the port? */
                        if (port->waithead) {
                                printk (KERN_DEBUG "Somebody wants the port\n");
                                break;
                        }
 
                        /* Clear serviceIntr */
                        ECR_WRITE (port, ecrval & ~(1<<2));
                false_alarm:
dump_parport_state ("waiting", port);
                        ret = parport_wait_event (port, HZ);
DPRINTK (KERN_DEBUG "parport_wait_event returned %d\n", ret);
                        if (ret < 0)
                                break;
                        ret = 0;
                        if (!time_before (jiffies, expire)) {
                                /* Timed out. */
dump_parport_state ("timeout", port);
                                printk (KERN_DEBUG "PIO read timed out\n");
                                break;
                        }
                        ecrval = inb (ECONTROL (port));
                        if (!(ecrval & (1<<2))) {
                                if (current->need_resched &&
                                    time_before (jiffies, expire)) {
                                        schedule ();
                                }
                                goto false_alarm;
                        }
 
                        /* Depending on how the FIFO threshold was
                         * set, how long interrupt service took, and
                         * how fast the peripheral is, we might be
                         * lucky and have a just filled FIFO. */
                        continue;
                }
 
                if (ecrval & 0x02) {
                        /* FIFO is full. */
dump_parport_state ("FIFO full", port);
                        insb (fifo, bufp, fifo_depth);
                        bufp += fifo_depth;
                        left -= fifo_depth;
                        continue;
                }
 
DPRINTK (KERN_DEBUG "*** ecp_read_block_pio: reading one byte from the FIFO\n");
 
                /* FIFO not filled.  We will cycle this loop for a while
                 * and either the peripheral will fill it faster,
                 * tripping a fast empty with insb, or we empty it. */
                *bufp++ = inb (fifo);
                left--;
        }
 
        /* scoop up anything left in the FIFO */
        while (left && !(inb (ECONTROL (port) & 0x01))) {
                *bufp++ = inb (fifo);
                left--;
        }
 
        port->ieee1284.phase = IEEE1284_PH_REV_IDLE;
dump_parport_state ("rev idle2", port);
 
out_no_data:
 
        /* Go to forward idle mode to shut the peripheral up (event 47). */
        parport_frob_control (port, PARPORT_CONTROL_INIT, PARPORT_CONTROL_INIT);
 
        /* event 49: PError goes high */
        r = parport_wait_peripheral (port,
                                     PARPORT_STATUS_PAPEROUT,
                                     PARPORT_STATUS_PAPEROUT);
        if (r) {
                printk (KERN_DEBUG
                        "%s: PE timeout FWDIDLE (%d) in ecp_read_block_pio\n",
                        port->name, r);
        }
 
        port->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
 
        /* Finish up. */
        {
                int lost = get_fifo_residue (port);
                if (lost)
                        /* Shouldn't happen with compliant peripherals. */
                        printk (KERN_DEBUG "%s: DATA LOSS (%d bytes)!\n",
                                port->name, lost);
        }
 
dump_parport_state ("fwd idle", port);
        return length - left;
}
 
#endif /* IEEE 1284 support */
#endif /* Allowed to use FIFO/DMA */
 
 
/*
 *      ******************************************
 *      INITIALISATION AND MODULE STUFF BELOW HERE
 *      ******************************************
 */
 
 
void parport_pc_inc_use_count(void)
{
#ifdef MODULE
        MOD_INC_USE_COUNT;
#endif
}
 
void parport_pc_dec_use_count(void)
{
#ifdef MODULE
        MOD_DEC_USE_COUNT;
#endif
}
 
struct parport_operations parport_pc_ops =
{
        parport_pc_write_data,
        parport_pc_read_data,
 
        parport_pc_write_control,
        parport_pc_read_control,
        parport_pc_frob_control,
 
        parport_pc_read_status,
 
        parport_pc_enable_irq,
        parport_pc_disable_irq,
 
        parport_pc_data_forward,
        parport_pc_data_reverse,
 
        parport_pc_init_state,
        parport_pc_save_state,
        parport_pc_restore_state,
 
        parport_pc_inc_use_count,
        parport_pc_dec_use_count,
 
        parport_ieee1284_epp_write_data,
        parport_ieee1284_epp_read_data,
        parport_ieee1284_epp_write_addr,
        parport_ieee1284_epp_read_addr,
 
        parport_ieee1284_ecp_write_data,
        parport_ieee1284_ecp_read_data,
        parport_ieee1284_ecp_write_addr,
 
        parport_ieee1284_write_compat,
        parport_ieee1284_read_nibble,
        parport_ieee1284_read_byte,
};
 
#ifdef CONFIG_PARPORT_PC_SUPERIO
/* Super-IO chipset detection, Winbond, SMSC */
static void __devinit show_parconfig_smsc37c669(int io, int key)
{
        int cr1,cr4,cra,cr23,cr26,cr27,i=0;
        static const char *modes[]={ "SPP and Bidirectional (PS/2)",
                                     "EPP and SPP",
                                     "ECP",
                                     "ECP and EPP" };
 
        outb(key,io);
        outb(key,io);
        outb(1,io);
        cr1=inb(io+1);
        outb(4,io);
        cr4=inb(io+1);
        outb(0x0a,io);
        cra=inb(io+1);
        outb(0x23,io);
        cr23=inb(io+1);
        outb(0x26,io);
        cr26=inb(io+1);
        outb(0x27,io);
        cr27=inb(io+1);
        outb(0xaa,io);
 
        if (verbose_probing) {
                printk (KERN_INFO "SMSC 37c669 LPT Config: cr_1=0x%02x, 4=0x%02x, "
                        "A=0x%2x, 23=0x%02x, 26=0x%02x, 27=0x%02x\n",
                        cr1,cr4,cra,cr23,cr26,cr27);
 
                /* The documentation calls DMA and IRQ-Lines by letters, so
                   the board maker can/will wire them
                   appropriately/randomly...  G=reserved H=IDE-irq, */
                printk (KERN_INFO "SMSC LPT Config: io=0x%04x, irq=%c, dma=%c, "
                        "fifo threshold=%d\n", cr23*4,
                        (cr27 &0x0f) ? 'A'-1+(cr27 &0x0f): '-',
                        (cr26 &0x0f) ? 'A'-1+(cr26 &0x0f): '-', cra & 0x0f);
                printk(KERN_INFO "SMSC LPT Config: enabled=%s power=%s\n",
                       (cr23*4 >=0x100) ?"yes":"no", (cr1 & 4) ? "yes" : "no");
                printk(KERN_INFO "SMSC LPT Config: Port mode=%s, EPP version =%s\n",
                       (cr1 & 0x08 ) ? "Standard mode only (SPP)" : modes[cr4 & 0x03],
                       (cr4 & 0x40) ? "1.7" : "1.9");
        }
 
        /* Heuristics !  BIOS setup for this mainboard device limits
           the choices to standard settings, i.e. io-address and IRQ
           are related, however DMA can be 1 or 3, assume DMA_A=DMA1,
           DMA_C=DMA3 (this is true e.g. for TYAN 1564D Tomcat IV) */
        if(cr23*4 >=0x100) { /* if active */
                while((superios[i].io!= 0) && (i<NR_SUPERIOS))
                        i++;
                if(i==NR_SUPERIOS)
                        printk(KERN_INFO "Super-IO: too many chips!\n");
                else {
                        int d;
                        switch (cr23*4) {
                                case 0x3bc:
                                        superios[i].io = 0x3bc;
                                        superios[i].irq = 7;
                                        break;
                                case 0x378:
                                        superios[i].io = 0x378;
                                        superios[i].irq = 7;
                                        break;
                                case 0x278:
                                        superios[i].io = 0x278;
                                        superios[i].irq = 5;
                        }
                        d=(cr26 &0x0f);
                        if((d==1) || (d==3))
                                superios[i].dma= d;
                        else
                                superios[i].dma= PARPORT_DMA_NONE;
                }
        }
}
 
 
static void __devinit show_parconfig_winbond(int io, int key)
{
        int cr30,cr60,cr61,cr70,cr74,crf0,i=0;
        static const char *modes[] = {
                "Standard (SPP) and Bidirectional(PS/2)", /* 0 */
                "EPP-1.9 and SPP",
                "ECP",
                "ECP and EPP-1.9",
                "Standard (SPP)",
                "EPP-1.7 and SPP",              /* 5 */
                "undefined!",
                "ECP and EPP-1.7" };
        static char *irqtypes[] = { "pulsed low, high-Z", "follows nACK" };
 
        /* The registers are called compatible-PnP because the
           register layout is modelled after ISA-PnP, the access
           method is just another ... */
        outb(key,io);
        outb(key,io);
        outb(0x07,io);   /* Register 7: Select Logical Device */
        outb(0x01,io+1); /* LD1 is Parallel Port */
        outb(0x30,io);
        cr30=inb(io+1);
        outb(0x60,io);
        cr60=inb(io+1);
        outb(0x61,io);
        cr61=inb(io+1);
        outb(0x70,io);
        cr70=inb(io+1);
        outb(0x74,io);
        cr74=inb(io+1);
        outb(0xf0,io);
        crf0=inb(io+1);
        outb(0xaa,io);
 
        if (verbose_probing) {
                printk(KERN_INFO "Winbond LPT Config: cr_30=%02x 60,61=%02x%02x "
                       "70=%02x 74=%02x, f0=%02x\n", cr30,cr60,cr61,cr70,cr74,crf0);
                printk(KERN_INFO "Winbond LPT Config: active=%s, io=0x%02x%02x irq=%d, ",
                       (cr30 & 0x01) ? "yes":"no", cr60,cr61,cr70&0x0f );
                if ((cr74 & 0x07) > 3)
                        printk("dma=none\n");
                else
                        printk("dma=%d\n",cr74 & 0x07);
                printk(KERN_INFO "Winbond LPT Config: irqtype=%s, ECP fifo threshold=%d\n",
                       irqtypes[crf0>>7], (crf0>>3)&0x0f);
                printk(KERN_INFO "Winbond LPT Config: Port mode=%s\n", modes[crf0 & 0x07]);
        }
 
        if(cr30 & 0x01) { /* the settings can be interrogated later ... */
                while((superios[i].io!= 0) && (i<NR_SUPERIOS))
                        i++;
                if(i==NR_SUPERIOS)
                        printk(KERN_INFO "Super-IO: too many chips!\n");
                else {
                        superios[i].io = (cr60<<8)|cr61;
                        superios[i].irq = cr70&0x0f;
                        superios[i].dma = (((cr74 & 0x07) > 3) ?
                                           PARPORT_DMA_NONE : (cr74 & 0x07));
                }
        }
}
 
static void __devinit decode_winbond(int efer, int key, int devid, int devrev, int oldid)
{
        const char *type = "unknown";
        int id,progif=2;
 
        if (devid == devrev)
                /* simple heuristics, we happened to read some
                   non-winbond register */
                return;
 
        id=(devid<<8) | devrev;
 
        /* Values are from public data sheets pdf files, I can just
           confirm 83977TF is correct :-) */
        if      (id == 0x9771) type="83977F/AF";
        else if (id == 0x9773) type="83977TF / SMSC 97w33x/97w34x";
        else if (id == 0x9774) type="83977ATF";
        else if ((id & ~0x0f) == 0x5270) type="83977CTF / SMSC 97w36x";
        else if ((id & ~0x0f) == 0x52f0) type="83977EF / SMSC 97w35x";
        else if ((id & ~0x0f) == 0x5210) type="83627";
        else if ((id & ~0x0f) == 0x6010) type="83697HF";
        else if ((oldid &0x0f ) == 0x0a) { type="83877F"; progif=1;}
        else if ((oldid &0x0f ) == 0x0b) { type="83877AF"; progif=1;}
        else if ((oldid &0x0f ) == 0x0c) { type="83877TF"; progif=1;}
        else if ((oldid &0x0f ) == 0x0d) { type="83877ATF"; progif=1;}
        else progif=0;
 
        if (verbose_probing)
                printk(KERN_INFO "Winbond chip at EFER=0x%x key=0x%02x "
                       "devid=%02x devrev=%02x oldid=%02x type=%s\n",
                       efer, key, devid, devrev, oldid, type);
 
        if (progif == 2)
                show_parconfig_winbond(efer,key);
}
 
static void __devinit decode_smsc(int efer, int key, int devid, int devrev)
{
        const char *type = "unknown";
        void (*func)(int io, int key);
        int id;
 
        if (devid == devrev)
                /* simple heuristics, we happened to read some
                   non-smsc register */
                return;
 
        func=NULL;
        id=(devid<<8) | devrev;
 
        if      (id==0x0302) {type="37c669"; func=show_parconfig_smsc37c669;}
        else if (id==0x6582) type="37c665IR";
        else if (devid==0x65) type="37c665GT";
        else if (devid==0x66) type="37c666GT";
 
        if (verbose_probing)
                printk(KERN_INFO "SMSC chip at EFER=0x%x "
                       "key=0x%02x devid=%02x devrev=%02x type=%s\n",
                       efer, key, devid, devrev, type);
 
        if (func)
                func(efer,key);
}
 
 
static void __devinit winbond_check(int io, int key)
{
        int devid,devrev,oldid,x_devid,x_devrev,x_oldid;
 
        /* First probe without key */
        outb(0x20,io);
        x_devid=inb(io+1);
        outb(0x21,io);
        x_devrev=inb(io+1);
        outb(0x09,io);
        x_oldid=inb(io+1);
 
        outb(key,io);
        outb(key,io);     /* Write Magic Sequence to EFER, extended
                             funtion enable register */
        outb(0x20,io);    /* Write EFIR, extended function index register */
        devid=inb(io+1);  /* Read EFDR, extended function data register */
        outb(0x21,io);
        devrev=inb(io+1);
        outb(0x09,io);
        oldid=inb(io+1);
        outb(0xaa,io);    /* Magic Seal */
 
        if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
                return; /* protection against false positives */
 
        decode_winbond(io,key,devid,devrev,oldid);
}
 
static void __devinit winbond_check2(int io,int key)
{
        int devid,devrev,oldid,x_devid,x_devrev,x_oldid;
 
        /* First probe without the key */
        outb(0x20,io+2);
        x_devid=inb(io+2);
        outb(0x21,io+1);
        x_devrev=inb(io+2);
        outb(0x09,io+1);
        x_oldid=inb(io+2);
 
        outb(key,io);     /* Write Magic Byte to EFER, extended
                             funtion enable register */
        outb(0x20,io+2);  /* Write EFIR, extended function index register */
        devid=inb(io+2);  /* Read EFDR, extended function data register */
        outb(0x21,io+1);
        devrev=inb(io+2);
        outb(0x09,io+1);
        oldid=inb(io+2);
        outb(0xaa,io);    /* Magic Seal */
 
        if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
                return; /* protection against false positives */
 
        decode_winbond(io,key,devid,devrev,oldid);
}
 
static void __devinit smsc_check(int io, int key)
{
        int id,rev,oldid,oldrev,x_id,x_rev,x_oldid,x_oldrev;
 
        /* First probe without the key */
        outb(0x0d,io);
        x_oldid=inb(io+1);
        outb(0x0e,io);
        x_oldrev=inb(io+1);
        outb(0x20,io);
        x_id=inb(io+1);
        outb(0x21,io);
        x_rev=inb(io+1);
 
        outb(key,io);
        outb(key,io);     /* Write Magic Sequence to EFER, extended
                             funtion enable register */
        outb(0x0d,io);    /* Write EFIR, extended function index register */
        oldid=inb(io+1);  /* Read EFDR, extended function data register */
        outb(0x0e,io);
        oldrev=inb(io+1);
        outb(0x20,io);
        id=inb(io+1);
        outb(0x21,io);
        rev=inb(io+1);
        outb(0xaa,io);    /* Magic Seal */
 
        if ((x_id == id) && (x_oldrev == oldrev) &&
            (x_oldid == oldid) && (x_rev == rev))
                return; /* protection against false positives */
 
        decode_smsc(io,key,oldid,oldrev);
}
 
 
static void __devinit detect_and_report_winbond (void)
{
        if (verbose_probing)
                printk(KERN_DEBUG "Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...\n");
        winbond_check(0x3f0,0x87);
        winbond_check(0x370,0x87);
        winbond_check(0x2e ,0x87);
        winbond_check(0x4e ,0x87);
        winbond_check(0x3f0,0x86);
        winbond_check2(0x250,0x88);
        winbond_check2(0x250,0x89);
}
 
static void __devinit detect_and_report_smsc (void)
{
        if (verbose_probing)
                printk(KERN_DEBUG "SMSC Super-IO detection, now testing Ports 2F0, 370 ...\n");
        smsc_check(0x3f0,0x55);
        smsc_check(0x370,0x55);
        smsc_check(0x3f0,0x44);
        smsc_check(0x370,0x44);
}
#endif /* CONFIG_PARPORT_PC_SUPERIO */
 
static int __devinit get_superio_dma (struct parport *p)
{
        int i=0;
        while( (superios[i].io != p->base) && (i<NR_SUPERIOS))
                i++;
        if (i!=NR_SUPERIOS)
                return superios[i].dma;
        return PARPORT_DMA_NONE;
}
 
static int __devinit get_superio_irq (struct parport *p)
{
        int i=0;
        while( (superios[i].io != p->base) && (i<NR_SUPERIOS))
                i++;
        if (i!=NR_SUPERIOS)
                return superios[i].irq;
        return PARPORT_IRQ_NONE;
}
 
 
/* --- Mode detection ------------------------------------- */
 
/*
 * Checks for port existence, all ports support SPP MODE
 * Returns:
 *         0           :  No parallel port at this adress
 *  PARPORT_MODE_PCSPP :  SPP port detected
 *                        (if the user specified an ioport himself,
 *                         this shall always be the case!)
 *
 */
static int __devinit parport_SPP_supported(struct parport *pb)
{
        unsigned char r, w;
 
        /*
         * first clear an eventually pending EPP timeout
         * I (sailer@ife.ee.ethz.ch) have an SMSC chipset
         * that does not even respond to SPP cycles if an EPP
         * timeout is pending
         */
        clear_epp_timeout(pb);
 
        /* Do a simple read-write test to make sure the port exists. */
        w = 0xc;
        outb (w, CONTROL (pb));
 
        /* Is there a control register that we can read from?  Some
         * ports don't allow reads, so read_control just returns a
         * software copy. Some ports _do_ allow reads, so bypass the
         * software copy here.  In addition, some bits aren't
         * writable. */
        r = inb (CONTROL (pb));
        if ((r & 0xf) == w) {
                w = 0xe;
                outb (w, CONTROL (pb));
                r = inb (CONTROL (pb));
                outb (0xc, CONTROL (pb));
                if ((r & 0xf) == w)
                        return PARPORT_MODE_PCSPP;
        }
 
        if (user_specified)
                /* That didn't work, but the user thinks there's a
                 * port here. */
                printk (KERN_INFO "parport 0x%lx (WARNING): CTR: "
                        "wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
 
        /* Try the data register.  The data lines aren't tri-stated at
         * this stage, so we expect back what we wrote. */
        w = 0xaa;
        parport_pc_write_data (pb, w);
        r = parport_pc_read_data (pb);
        if (r == w) {
                w = 0x55;
                parport_pc_write_data (pb, w);
                r = parport_pc_read_data (pb);
                if (r == w)
                        return PARPORT_MODE_PCSPP;
        }
 
        if (user_specified) {
                /* Didn't work, but the user is convinced this is the
                 * place. */
                printk (KERN_INFO "parport 0x%lx (WARNING): DATA: "
                        "wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
                printk (KERN_INFO "parport 0x%lx: You gave this address, "
                        "but there is probably no parallel port there!\n",
                        pb->base);
        }
 
        /* It's possible that we can't read the control register or
         * the data register.  In that case just believe the user. */
        if (user_specified)
                return PARPORT_MODE_PCSPP;
 
        return 0;
}
 
/* Check for ECR
 *
 * Old style XT ports alias io ports every 0x400, hence accessing ECR
 * on these cards actually accesses the CTR.
 *
 * Modern cards don't do this but reading from ECR will return 0xff
 * regardless of what is written here if the card does NOT support
 * ECP.
 *
 * We first check to see if ECR is the same as CTR.  If not, the low
 * two bits of ECR aren't writable, so we check by writing ECR and
 * reading it back to see if it's what we expect.
 */
static int __devinit parport_ECR_present(struct parport *pb)
{
        struct parport_pc_private *priv = pb->private_data;
        unsigned char r = 0xc;
 
        outb (r, CONTROL (pb));
        if ((inb (ECONTROL (pb)) & 0x3) == (r & 0x3)) {
                outb (r ^ 0x2, CONTROL (pb)); /* Toggle bit 1 */
 
                r = inb (CONTROL (pb));
                if ((inb (ECONTROL (pb)) & 0x2) == (r & 0x2))
                        goto no_reg; /* Sure that no ECR register exists */
        }
 
        if ((inb (ECONTROL (pb)) & 0x3 ) != 0x1)
                goto no_reg;
 
        ECR_WRITE (pb, 0x34);
        if (inb (ECONTROL (pb)) != 0x35)
                goto no_reg;
 
        priv->ecr = 1;
        outb (0xc, CONTROL (pb));
 
        /* Go to mode 000 */
        frob_set_mode (pb, ECR_SPP);
 
        return 1;
 
 no_reg:
        outb (0xc, CONTROL (pb));
        return 0;
}
 
#ifdef CONFIG_PARPORT_1284
/* Detect PS/2 support.
 *
 * Bit 5 (0x20) sets the PS/2 data direction; setting this high
 * allows us to read data from the data lines.  In theory we would get back
 * 0xff but any peripheral attached to the port may drag some or all of the
 * lines down to zero.  So if we get back anything that isn't the contents
 * of the data register we deem PS/2 support to be present.
 *
 * Some SPP ports have "half PS/2" ability - you can't turn off the line
 * drivers, but an external peripheral with sufficiently beefy drivers of
 * its own can overpower them and assert its own levels onto the bus, from
 * where they can then be read back as normal.  Ports with this property
 * and the right type of device attached are likely to fail the SPP test,
 * (as they will appear to have stuck bits) and so the fact that they might
 * be misdetected here is rather academic.
 */
 
static int __devinit parport_PS2_supported(struct parport *pb)
{
        int ok = 0;
 
        clear_epp_timeout(pb);
 
        /* try to tri-state the buffer */
        parport_pc_data_reverse (pb);
 
        parport_pc_write_data(pb, 0x55);
        if (parport_pc_read_data(pb) != 0x55) ok++;
 
        parport_pc_write_data(pb, 0xaa);
        if (parport_pc_read_data(pb) != 0xaa) ok++;
 
        /* cancel input mode */
        parport_pc_data_forward (pb);
 
        if (ok) {
                pb->modes |= PARPORT_MODE_TRISTATE;
        } else {
                struct parport_pc_private *priv = pb->private_data;
                priv->ctr_writable &= ~0x20;
        }
 
        return ok;
}
 
#ifdef CONFIG_PARPORT_PC_FIFO
static int __devinit parport_ECP_supported(struct parport *pb)
{
        int i;
        int config, configb;
        int pword;
        struct parport_pc_private *priv = pb->private_data;
        /* Translate ECP intrLine to ISA irq value */
        static const int intrline[]= { 0, 7, 9, 10, 11, 14, 15, 5 };
 
        /* If there is no ECR, we have no hope of supporting ECP. */
        if (!priv->ecr)
                return 0;
 
        /* Find out FIFO depth */
        ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
        ECR_WRITE (pb, ECR_TST << 5); /* TEST FIFO */
        for (i=0; i < 1024 && !(inb (ECONTROL (pb)) & 0x02); i++)
                outb (0xaa, FIFO (pb));
 
        /*
         * Using LGS chipset it uses ECR register, but
         * it doesn't support ECP or FIFO MODE
         */
        if (i == 1024) {
                ECR_WRITE (pb, ECR_SPP << 5);
                return 0;
        }
 
        priv->fifo_depth = i;
        if (verbose_probing)
                printk (KERN_DEBUG "0x%lx: FIFO is %d bytes\n", pb->base, i);
 
        /* Find out writeIntrThreshold */
        frob_econtrol (pb, 1<<2, 1<<2);
        frob_econtrol (pb, 1<<2, 0);
        for (i = 1; i <= priv->fifo_depth; i++) {
                inb (FIFO (pb));
                udelay (50);
                if (inb (ECONTROL (pb)) & (1<<2))
                        break;
        }
 
        if (i <= priv->fifo_depth) {
                if (verbose_probing)
                        printk (KERN_DEBUG "0x%lx: writeIntrThreshold is %d\n",
                                pb->base, i);
        } else
                /* Number of bytes we know we can write if we get an
                   interrupt. */
                i = 0;
 
        priv->writeIntrThreshold = i;
 
        /* Find out readIntrThreshold */
        frob_set_mode (pb, ECR_PS2); /* Reset FIFO and enable PS2 */
        parport_pc_data_reverse (pb); /* Must be in PS2 mode */
        frob_set_mode (pb, ECR_TST); /* Test FIFO */
        frob_econtrol (pb, 1<<2, 1<<2);
        frob_econtrol (pb, 1<<2, 0);
        for (i = 1; i <= priv->fifo_depth; i++) {
                outb (0xaa, FIFO (pb));
                if (inb (ECONTROL (pb)) & (1<<2))
                        break;
        }
 
        if (i <= priv->fifo_depth) {
                if (verbose_probing)
                        printk (KERN_INFO "0x%lx: readIntrThreshold is %d\n",
                                pb->base, i);
        } else
                /* Number of bytes we can read if we get an interrupt. */
                i = 0;
 
        priv->readIntrThreshold = i;
 
        ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
        ECR_WRITE (pb, 0xf4); /* Configuration mode */
        config = inb (CONFIGA (pb));
        pword = (config >> 4) & 0x7;
        switch (pword) {
        case 0:
                pword = 2;
                printk (KERN_WARNING "0x%lx: Unsupported pword size!\n",
                        pb->base);
                break;
        case 2:
                pword = 4;
                printk (KERN_WARNING "0x%lx: Unsupported pword size!\n",
                        pb->base);
                break;
        default:
                printk (KERN_WARNING "0x%lx: Unknown implementation ID\n",
                        pb->base);
                /* Assume 1 */
        case 1:
                pword = 1;
        }
        priv->pword = pword;
 
        if (verbose_probing) {
                printk (KERN_DEBUG "0x%lx: PWord is %d bits\n", pb->base, 8 * pword);
 
                printk (KERN_DEBUG "0x%lx: Interrupts are ISA-%s\n", pb->base,
                        config & 0x80 ? "Level" : "Pulses");
 
                configb = inb (CONFIGB (pb));
                printk (KERN_DEBUG "0x%lx: ECP port cfgA=0x%02x cfgB=0x%02x\n",
                        pb->base, config, configb);
                printk (KERN_DEBUG "0x%lx: ECP settings irq=", pb->base);
                if ((configb >>3) & 0x07)
                        printk("%d",intrline[(configb >>3) & 0x07]);
                else
                        printk("<none or set by other means>");
                printk (" dma=");
                if( (configb & 0x03 ) == 0x00)
                        printk("<none or set by other means>\n");
                else
                        printk("%d\n",configb & 0x07);
        }
 
        /* Go back to mode 000 */
        frob_set_mode (pb, ECR_SPP);
 
        return 1;
}
#endif
 
static int __devinit parport_ECPPS2_supported(struct parport *pb)
{
        const struct parport_pc_private *priv = pb->private_data;
        int result;
        unsigned char oecr;
 
        if (!priv->ecr)
                return 0;
 
        oecr = inb (ECONTROL (pb));
        ECR_WRITE (pb, ECR_PS2 << 5);
        result = parport_PS2_supported(pb);
        ECR_WRITE (pb, oecr);
        return result;
}
 
/* EPP mode detection  */
 
static int __devinit parport_EPP_supported(struct parport *pb)
{
        const struct parport_pc_private *priv = pb->private_data;
 
        /*
         * Theory:
         *      Bit 0 of STR is the EPP timeout bit, this bit is 0
         *      when EPP is possible and is set high when an EPP timeout
         *      occurs (EPP uses the HALT line to stop the CPU while it does
         *      the byte transfer, an EPP timeout occurs if the attached
         *      device fails to respond after 10 micro seconds).
         *
         *      This bit is cleared by either reading it (National Semi)
         *      or writing a 1 to the bit (SMC, UMC, WinBond), others ???
         *      This bit is always high in non EPP modes.
         */
 
        /* If EPP timeout bit clear then EPP available */
        if (!clear_epp_timeout(pb)) {
                return 0;  /* No way to clear timeout */
        }
 
        /* Check for Intel bug. */
        if (priv->ecr) {
                unsigned char i;
                for (i = 0x00; i < 0x80; i += 0x20) {
                        ECR_WRITE (pb, i);
                        if (clear_epp_timeout (pb)) {
                                /* Phony EPP in ECP. */
                                return 0;
                        }
                }
        }
 
        pb->modes |= PARPORT_MODE_EPP;
 
        /* Set up access functions to use EPP hardware. */
        pb->ops->epp_read_data = parport_pc_epp_read_data;
        pb->ops->epp_write_data = parport_pc_epp_write_data;
        pb->ops->epp_read_addr = parport_pc_epp_read_addr;
        pb->ops->epp_write_addr = parport_pc_epp_write_addr;
 
        return 1;
}
 
static int __devinit parport_ECPEPP_supported(struct parport *pb)
{
        struct parport_pc_private *priv = pb->private_data;
        int result;
        unsigned char oecr;
 
        if (!priv->ecr) {
                return 0;
        }
 
        oecr = inb (ECONTROL (pb));
        /* Search for SMC style EPP+ECP mode */
        ECR_WRITE (pb, 0x80);
        outb (0x04, CONTROL (pb));
        result = parport_EPP_supported(pb);
 
        ECR_WRITE (pb, oecr);
 
        if (result) {
                /* Set up access functions to use ECP+EPP hardware. */
                pb->ops->epp_read_data = parport_pc_ecpepp_read_data;
                pb->ops->epp_write_data = parport_pc_ecpepp_write_data;
                pb->ops->epp_read_addr = parport_pc_ecpepp_read_addr;
                pb->ops->epp_write_addr = parport_pc_ecpepp_write_addr;
        }
 
        return result;
}
 
#else /* No IEEE 1284 support */
 
/* Don't bother probing for modes we know we won't use. */
static int __devinit parport_PS2_supported(struct parport *pb) { return 0; }
#ifdef CONFIG_PARPORT_PC_FIFO
static int __devinit parport_ECP_supported(struct parport *pb) { return 0; }
#endif
static int __devinit parport_EPP_supported(struct parport *pb) { return 0; }
static int __devinit parport_ECPEPP_supported(struct parport *pb){return 0;}
static int __devinit parport_ECPPS2_supported(struct parport *pb){return 0;}
 
#endif /* No IEEE 1284 support */
 
/* --- IRQ detection -------------------------------------- */
 
/* Only if supports ECP mode */
static int __devinit programmable_irq_support(struct parport *pb)
{
        int irq, intrLine;
        unsigned char oecr = inb (ECONTROL (pb));
        static const int lookup[8] = {
                PARPORT_IRQ_NONE, 7, 9, 10, 11, 14, 15, 5
        };
 
        ECR_WRITE (pb, ECR_CNF << 5); /* Configuration MODE */
 
        intrLine = (inb (CONFIGB (pb)) >> 3) & 0x07;
        irq = lookup[intrLine];
 
        ECR_WRITE (pb, oecr);
        return irq;
}
 
static int __devinit irq_probe_ECP(struct parport *pb)
{
        int i;
        unsigned long irqs;
 
        sti();
        irqs = probe_irq_on();
 
        ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
        ECR_WRITE (pb, (ECR_TST << 5) | 0x04);
        ECR_WRITE (pb, ECR_TST << 5);
 
        /* If Full FIFO sure that writeIntrThreshold is generated */
        for (i=0; i < 1024 && !(inb (ECONTROL (pb)) & 0x02) ; i++)
                outb (0xaa, FIFO (pb));
 
        pb->irq = probe_irq_off(irqs);
        ECR_WRITE (pb, ECR_SPP << 5);
 
        if (pb->irq <= 0)
                pb->irq = PARPORT_IRQ_NONE;
 
        return pb->irq;
}
 
/*
 * This detection seems that only works in National Semiconductors
 * This doesn't work in SMC, LGS, and Winbond
 */
static int __devinit irq_probe_EPP(struct parport *pb)
{
#ifndef ADVANCED_DETECT
        return PARPORT_IRQ_NONE;
#else
        int irqs;
        unsigned char oecr;
 
        if (pb->modes & PARPORT_MODE_PCECR)
                oecr = inb (ECONTROL (pb));
 
        sti();
        irqs = probe_irq_on();
 
        if (pb->modes & PARPORT_MODE_PCECR)
                frob_econtrol (pb, 0x10, 0x10);
 
        clear_epp_timeout(pb);
        parport_pc_frob_control (pb, 0x20, 0x20);
        parport_pc_frob_control (pb, 0x10, 0x10);
        clear_epp_timeout(pb);
 
        /* Device isn't expecting an EPP read
         * and generates an IRQ.
         */
        parport_pc_read_epp(pb);
        udelay(20);
 
        pb->irq = probe_irq_off (irqs);
        if (pb->modes & PARPORT_MODE_PCECR)
                ECR_WRITE (pb, oecr);
        parport_pc_write_control(pb, 0xc);
 
        if (pb->irq <= 0)
                pb->irq = PARPORT_IRQ_NONE;
 
        return pb->irq;
#endif /* Advanced detection */
}
 
static int __devinit irq_probe_SPP(struct parport *pb)
{
        /* Don't even try to do this. */
        return PARPORT_IRQ_NONE;
}
 
/* We will attempt to share interrupt requests since other devices
 * such as sound cards and network cards seem to like using the
 * printer IRQs.
 *
 * When ECP is available we can autoprobe for IRQs.
 * NOTE: If we can autoprobe it, we can register the IRQ.
 */
static int __devinit parport_irq_probe(struct parport *pb)
{
        struct parport_pc_private *priv = pb->private_data;
 
        if (priv->ecr) {
                pb->irq = programmable_irq_support(pb);
 
                if (pb->irq == PARPORT_IRQ_NONE)
                        pb->irq = irq_probe_ECP(pb);
        }
 
        if ((pb->irq == PARPORT_IRQ_NONE) && priv->ecr &&
            (pb->modes & PARPORT_MODE_EPP))
                pb->irq = irq_probe_EPP(pb);
 
        clear_epp_timeout(pb);
 
        if (pb->irq == PARPORT_IRQ_NONE && (pb->modes & PARPORT_MODE_EPP))
                pb->irq = irq_probe_EPP(pb);
 
        clear_epp_timeout(pb);
 
        if (pb->irq == PARPORT_IRQ_NONE)
                pb->irq = irq_probe_SPP(pb);
 
        if (pb->irq == PARPORT_IRQ_NONE)
                pb->irq = get_superio_irq(pb);
 
        return pb->irq;
}
 
/* --- DMA detection -------------------------------------- */
 
/* Only if chipset conforms to ECP ISA Interface Standard */
static int __devinit programmable_dma_support (struct parport *p)
{
        unsigned char oecr = inb (ECONTROL (p));
        int dma;
 
        frob_set_mode (p, ECR_CNF);
 
        dma = inb (CONFIGB(p)) & 0x07;
        /* 000: Indicates jumpered 8-bit DMA if read-only.
           100: Indicates jumpered 16-bit DMA if read-only. */
        if ((dma & 0x03) == 0)
                dma = PARPORT_DMA_NONE;
 
        ECR_WRITE (p, oecr);
        return dma;
}
 
static int __devinit parport_dma_probe (struct parport *p)
{
        const struct parport_pc_private *priv = p->private_data;
        if (priv->ecr)
                p->dma = programmable_dma_support(p); /* ask ECP chipset first */
        if (p->dma == PARPORT_DMA_NONE) {
                /* ask known Super-IO chips proper, although these
                   claim ECP compatible, some don't report their DMA
                   conforming to ECP standards */
                p->dma = get_superio_dma(p);
        }
 
        return p->dma;
}
 
/* --- Initialisation code -------------------------------- */
 
struct parport *parport_pc_probe_port (unsigned long int base,
                                       unsigned long int base_hi,
                                       int irq, int dma,
                                       struct pci_dev *dev)
{
        struct parport_pc_private *priv;
        struct parport_operations *ops;
        struct parport tmp;
        struct parport *p = &tmp;
        int probedirq = PARPORT_IRQ_NONE;
        if (check_region(base, 3)) return NULL;
        priv = kmalloc (sizeof (struct parport_pc_private), GFP_KERNEL);
        if (!priv) {
                printk (KERN_DEBUG "parport (0x%lx): no memory!\n", base);
                return NULL;
        }
        ops = kmalloc (sizeof (struct parport_operations), GFP_KERNEL);
        if (!ops) {
                printk (KERN_DEBUG "parport (0x%lx): no memory for ops!\n",
                        base);
                kfree (priv);
                return NULL;
        }
        memcpy (ops, &parport_pc_ops, sizeof (struct parport_operations));
        priv->ctr = 0xc;
        priv->ctr_writable = ~0x10;
        priv->ecr = 0;
        priv->fifo_depth = 0;
        priv->dma_buf = 0;
        priv->dma_handle = 0;
        priv->dev = dev;
        p->base = base;
        p->base_hi = base_hi;
        p->irq = irq;
        p->dma = dma;
        p->modes = PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT;
        p->ops = ops;
        p->private_data = priv;
        p->physport = p;
 
        if (base_hi && !check_region(base_hi,3))
                parport_ECR_present(p);
 
        if (base != 0x3bc) {
                if (!check_region(base+0x3, 5)) {
                        if (!parport_EPP_supported(p))
                                parport_ECPEPP_supported(p);
                }
        }
        if (!parport_SPP_supported (p)) {
                /* No port. */
                kfree (priv);
                kfree (ops);
                return NULL;
        }
        if (priv->ecr)
                parport_ECPPS2_supported(p);
        else
                parport_PS2_supported (p);
 
        if (!(p = parport_register_port(base, PARPORT_IRQ_NONE,
                                        PARPORT_DMA_NONE, ops))) {
                kfree (priv);
                kfree (ops);
                return NULL;
        }
 
        p->base_hi = base_hi;
        p->modes = tmp.modes;
        p->size = (p->modes & PARPORT_MODE_EPP)?8:3;
        p->private_data = priv;
 
        printk(KERN_INFO "%s: PC-style at 0x%lx", p->name, p->base);
        if (p->base_hi && priv->ecr)
                printk(" (0x%lx)", p->base_hi);
        p->irq = irq;
        p->dma = dma;
        if (p->irq == PARPORT_IRQ_AUTO) {
                p->irq = PARPORT_IRQ_NONE;
                parport_irq_probe(p);
        } else if (p->irq == PARPORT_IRQ_PROBEONLY) {
                p->irq = PARPORT_IRQ_NONE;
                parport_irq_probe(p);
                probedirq = p->irq;
                p->irq = PARPORT_IRQ_NONE;
        }
        if (p->irq != PARPORT_IRQ_NONE) {
                printk(", irq %d", p->irq);
                priv->ctr_writable |= 0x10;
 
                if (p->dma == PARPORT_DMA_AUTO) {
                        p->dma = PARPORT_DMA_NONE;
                        parport_dma_probe(p);
                }
        }
        if (p->dma == PARPORT_DMA_AUTO) /* To use DMA, giving the irq
                                           is mandatory (see above) */
                p->dma = PARPORT_DMA_NONE;
 
#ifdef CONFIG_PARPORT_PC_FIFO
        if (parport_ECP_supported(p) &&
            p->dma != PARPORT_DMA_NOFIFO &&
            priv->fifo_depth > 0 && p->irq != PARPORT_IRQ_NONE) {
                p->modes |= PARPORT_MODE_ECP | PARPORT_MODE_COMPAT;
                p->ops->compat_write_data = parport_pc_compat_write_block_pio;
#ifdef CONFIG_PARPORT_1284
                p->ops->ecp_write_data = parport_pc_ecp_write_block_pio;
                /* currently broken, but working on it.. (FB) */
                /* p->ops->ecp_read_data = parport_pc_ecp_read_block_pio; */
#endif /* IEEE 1284 support */
                if (p->dma != PARPORT_DMA_NONE) {
                        printk(", dma %d", p->dma);
                        p->modes |= PARPORT_MODE_DMA;
                }
                else printk(", using FIFO");
        }
        else
                /* We can't use the DMA channel after all. */
                p->dma = PARPORT_DMA_NONE;
#endif /* Allowed to use FIFO/DMA */
 
        printk(" [");
#define printmode(x) {if(p->modes&PARPORT_MODE_##x){printk("%s%s",f?",":"",#x);f++;}}
        {
                int f = 0;
                printmode(PCSPP);
                printmode(TRISTATE);
                printmode(COMPAT)
                printmode(EPP);
                printmode(ECP);
                printmode(DMA);
        }
#undef printmode
#ifndef CONFIG_PARPORT_1284
        printk ("(,...)");
#endif /* CONFIG_PARPORT_1284 */
        printk("]\n");
        if (probedirq != PARPORT_IRQ_NONE)
                printk(KERN_INFO "%s: irq %d detected\n", p->name, probedirq);
        parport_proc_register(p);
 
        request_region (p->base, 3, p->name);
        if (p->size > 3)
                request_region (p->base + 3, p->size - 3, p->name);
        if (p->modes & PARPORT_MODE_ECP)
                request_region (p->base_hi, 3, p->name);
 
        if (p->irq != PARPORT_IRQ_NONE) {
                if (request_irq (p->irq, parport_pc_interrupt,
                                 0, p->name, p)) {
                        printk (KERN_WARNING "%s: irq %d in use, "
                                "resorting to polled operation\n",
                                p->name, p->irq);
                        p->irq = PARPORT_IRQ_NONE;
                        p->dma = PARPORT_DMA_NONE;
                }
 
#ifdef CONFIG_PARPORT_PC_FIFO
                if (p->dma != PARPORT_DMA_NONE) {
                        if (request_dma (p->dma, p->name)) {
                                printk (KERN_WARNING "%s: dma %d in use, "
                                        "resorting to PIO operation\n",
                                        p->name, p->dma);
                                p->dma = PARPORT_DMA_NONE;
                        } else {
                                priv->dma_buf =
                                  pci_alloc_consistent(priv->dev,
                                                       PAGE_SIZE,
                                                       &priv->dma_handle);
                                if (! priv->dma_buf) {
                                        printk (KERN_WARNING "%s: "
                                                "cannot get buffer for DMA, "
                                                "resorting to PIO operation\n",
                                                p->name);
                                        free_dma(p->dma);
                                        p->dma = PARPORT_DMA_NONE;
                                }
                        }
                }
#endif /* CONFIG_PARPORT_PC_FIFO */
        }
 
        /* Done probing.  Now put the port into a sensible start-up state. */
        if (priv->ecr)
                /*
                 * Put the ECP detected port in PS2 mode.
                 * Do this also for ports that have ECR but don't do ECP.
                 */
                ECR_WRITE (p, 0x34);
 
        parport_pc_write_data(p, 0);
        parport_pc_data_forward (p);
 
        /* Now that we've told the sharing engine about the port, and
           found out its characteristics, let the high-level drivers
           know about it. */
        parport_announce_port (p);
 
        return p;
}
 
void parport_pc_unregister_port (struct parport *p)
{
#ifdef CONFIG_PARPORT_PC_FIFO
        struct parport_pc_private *priv = p->private_data;
#endif /* CONFIG_PARPORT_PC_FIFO */
        struct parport_operations *ops = p->ops;
        if (p->dma != PARPORT_DMA_NONE)
                free_dma(p->dma);
        if (p->irq != PARPORT_IRQ_NONE)
                free_irq(p->irq, p);
        release_region(p->base, 3);
        if (p->size > 3)
                release_region(p->base + 3, p->size - 3);
        if (p->modes & PARPORT_MODE_ECP)
                release_region(p->base_hi, 3);
        parport_proc_unregister(p);
#ifdef CONFIG_PARPORT_PC_FIFO
        if (priv->dma_buf)
                pci_free_consistent(priv->dev, PAGE_SIZE,
                                    priv->dma_buf,
                                    priv->dma_handle);
#endif /* CONFIG_PARPORT_PC_FIFO */
        kfree (p->private_data);
        parport_unregister_port(p);
        kfree (ops); /* hope no-one cached it */
}
 
#ifdef CONFIG_PCI
 
/* ITE support maintained by Rich Liu <richliu@poorman.org> */
static int __devinit sio_ite_8872_probe (struct pci_dev *pdev, int autoirq,
                                         int autodma)
{
        short inta_addr[6] = { 0x2A0, 0x2C0, 0x220, 0x240, 0x1E0 };
        u32 ite8872set;
        u32 ite8872_lpt, ite8872_lpthi;
        u8 ite8872_irq, type;
        int irq;
        int i;
 
        DPRINTK (KERN_DEBUG "sio_ite_8872_probe()\n");
 
        // make sure which one chip
        for(i = 0; i < 5; i++) {
                if (check_region (inta_addr[i], 0x8) >= 0) {
                        int test;
                        pci_write_config_dword (pdev, 0x60,
                                                0xe7000000 | inta_addr[i]);
                        pci_write_config_dword (pdev, 0x78,
                                                0x00000000 | inta_addr[i]);
                        test = inb (inta_addr[i]);
                        if (test != 0xff) break;
                }
        }
        if(i >= 5) {
                printk (KERN_INFO "parport_pc: cannot find ITE8872 INTA\n");
                return 0;
        }
 
        type = inb (inta_addr[i] + 0x18);
        type &= 0x0f;
 
        switch (type) {
        case 0x2:
                printk (KERN_INFO "parport_pc: ITE8871 found (1P)\n");
                ite8872set = 0x64200000;
                break;
        case 0xa:
                printk (KERN_INFO "parport_pc: ITE8875 found (1P)\n");
                ite8872set = 0x64200000;
                break;
        case 0xe:
                printk (KERN_INFO "parport_pc: ITE8872 found (2S1P)\n");
                ite8872set = 0x64e00000;
                break;
        case 0x6:
                printk (KERN_INFO "parport_pc: ITE8873 found (1S)\n");
                return 0;
        case 0x8:
                DPRINTK (KERN_DEBUG "parport_pc: ITE8874 found (2S)\n");
                return 0;
        default:
                printk (KERN_INFO "parport_pc: unknown ITE887x\n");
                printk (KERN_INFO "parport_pc: please mail 'lspci -nvv' "
                        "output to Rich.Liu@ite.com.tw\n");
                return 0;
        }
 
        pci_read_config_byte (pdev, 0x3c, &ite8872_irq);
        pci_read_config_dword (pdev, 0x1c, &ite8872_lpt);
        ite8872_lpt &= 0x0000ff00;
        pci_read_config_dword (pdev, 0x20, &ite8872_lpthi);
        ite8872_lpthi &= 0x0000ff00;
        pci_write_config_dword (pdev, 0x6c, 0xe3000000 | ite8872_lpt);
        pci_write_config_dword (pdev, 0x70, 0xe3000000 | ite8872_lpthi);
        pci_write_config_dword (pdev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt);
        // SET SPP&EPP , Parallel Port NO DMA , Enable All Function
        // SET Parallel IRQ
        pci_write_config_dword (pdev, 0x9c,
                                ite8872set | (ite8872_irq * 0x11111));
 
        DPRINTK (KERN_DEBUG "ITE887x: The IRQ is %d.\n", ite8872_irq);
        DPRINTK (KERN_DEBUG "ITE887x: The PARALLEL I/O port is 0x%x.\n",
                 ite8872_lpt);
        DPRINTK (KERN_DEBUG "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
                 ite8872_lpthi);
 
        /* Let the user (or defaults) steer us away from interrupts */
        irq = ite8872_irq;
        if (autoirq != PARPORT_IRQ_AUTO)
                irq = PARPORT_IRQ_NONE;
 
        if (parport_pc_probe_port (ite8872_lpt, ite8872_lpthi,
                                   irq, PARPORT_DMA_NONE, NULL)) {
                printk (KERN_INFO
                        "parport_pc: ITE 8872 parallel port: io=0x%X",
                        ite8872_lpt);
                if (irq != PARPORT_IRQ_NONE)
                        printk (", irq=%d", irq);
                printk ("\n");
                return 1;
        }
 
        return 0;
}
 
/* Via support maintained by Jeff Garzik <jgarzik@pobox.com> */
static int __devinit sio_via_686a_probe (struct pci_dev *pdev, int autoirq,
                                         int autodma)
{
        u8 tmp;
        int dma, irq;
        unsigned port1, port2, have_eppecp;
 
        /*
         * unlock super i/o configuration, set 0x85_1
         */
        pci_read_config_byte (pdev, 0x85, &tmp);
        tmp |= (1 << 1);
        pci_write_config_byte (pdev, 0x85, tmp);
 
        /*
         * Super I/O configuration, index port == 3f0h, data port == 3f1h
         */
 
        /* 0xE2_1-0: Parallel Port Mode / Enable */
        outb (0xE2, 0x3F0);
        tmp = inb (0x3F1);
 
        if ((tmp & 0x03) == 0x03) {
                printk (KERN_INFO "parport_pc: Via 686A parallel port disabled in BIOS\n");
                return 0;
        }
 
        /* 0xE6: Parallel Port I/O Base Address, bits 9-2 */
        outb (0xE6, 0x3F0);
        port1 = inb (0x3F1) << 2;
 
        switch (port1) {
        case 0x3bc: port2 = 0x7bc; break;
        case 0x378: port2 = 0x778; break;
        case 0x278: port2 = 0x678; break;
        default:
                printk (KERN_INFO "parport_pc: Weird Via 686A parport base 0x%X, ignoring\n",
                        port1);
                return 0;
        }
 
        /* 0xF0_5: EPP+ECP enable */
        outb (0xF0, 0x3F0);
        have_eppecp = (inb (0x3F1) & (1 << 5));
 
        /*
         * lock super i/o configuration, clear 0x85_1
         */
        pci_read_config_byte (pdev, 0x85, &tmp);
        tmp &= ~(1 << 1);
        pci_write_config_byte (pdev, 0x85, tmp);
 
        /*
         * Get DMA and IRQ from PCI->ISA bridge PCI config registers
         */
 
        /* 0x50_3-2: PnP Routing for Parallel Port DRQ */
        pci_read_config_byte (pdev, 0x50, &tmp);
        dma = ((tmp >> 2) & 0x03);
 
        /* 0x51_7-4: PnP Routing for Parallel Port IRQ */
        pci_read_config_byte (pdev, 0x51, &tmp);
        irq = ((tmp >> 4) & 0x0F);
 
        /* filter bogus IRQs */
        switch (irq) {
        case 0:
        case 2:
        case 8:
        case 13:
                irq = PARPORT_IRQ_NONE;
                break;
 
        default: /* do nothing */
                break;
        }
 
        /* if ECP not enabled, DMA is not enabled, assumed bogus 'dma' value */
        if (!have_eppecp)
                dma = PARPORT_DMA_NONE;
 
        /* Let the user (or defaults) steer us away from interrupts and DMA */
        if (autoirq != PARPORT_IRQ_AUTO) {
                irq = PARPORT_IRQ_NONE;
                dma = PARPORT_DMA_NONE;
        }
        if (autodma != PARPORT_DMA_AUTO)
                dma = PARPORT_DMA_NONE;
 
        /* finally, do the probe with values obtained */
        if (parport_pc_probe_port (port1, port2, irq, dma, NULL)) {
                printk (KERN_INFO
                        "parport_pc: Via 686A parallel port: io=0x%X", port1);
                if (irq != PARPORT_IRQ_NONE)
                        printk (", irq=%d", irq);
                if (dma != PARPORT_DMA_NONE)
                        printk (", dma=%d", dma);
                printk ("\n");
                return 1;
        }
 
        printk (KERN_WARNING "parport_pc: Strange, can't probe Via 686A parallel port: io=0x%X, irq=%d, dma=%d\n",
                port1, irq, dma);
        return 0;
}
 
 
enum parport_pc_sio_types {
        sio_via_686a = 0,        /* Via VT82C686A motherboard Super I/O */
        sio_ite_8872,
        last_sio
};
 
/* each element directly indexed from enum list, above */
static struct parport_pc_superio {
        int (*probe) (struct pci_dev *pdev, int autoirq, int autodma);
} parport_pc_superio_info[] __devinitdata = {
        { sio_via_686a_probe, },
        { sio_ite_8872_probe, },
};
 
 
enum parport_pc_pci_cards {
        siig_1p_10x = last_sio,
        siig_2p_10x,
        siig_1p_20x,
        siig_2p_20x,
        lava_parallel,
        lava_parallel_dual_a,
        lava_parallel_dual_b,
        boca_ioppar,
        plx_9050,
        timedia_4078a,
        timedia_4079h,
        timedia_4085h,
        timedia_4088a,
        timedia_4089a,
        timedia_4095a,
        timedia_4096a,
        timedia_4078u,
        timedia_4079a,
        timedia_4085u,
        timedia_4079r,
        timedia_4079s,
        timedia_4079d,
        timedia_4079e,
        timedia_4079f,
        timedia_9079a,
        timedia_9079b,
        timedia_9079c,
        timedia_4006a,
        timedia_4014,
        timedia_4008a,
        timedia_4018,
        timedia_9018a,
        syba_2p_epp,
        syba_1p_ecp,
        titan_010l,
        titan_1284p2,
        avlab_1p,
        avlab_2p,
        oxsemi_954,
        oxsemi_840,
        aks_0100,
        mobility_pp,
};
 
 
/* each element directly indexed from enum list, above
 * (but offset by last_sio) */
static struct parport_pc_pci {
        int numports;
        struct { /* BAR (base address registers) numbers in the config
                    space header */
                int lo;
                int hi; /* -1 if not there, >6 for offset-method (max
                           BAR is 6) */
        } addr[4];
 
        /* If set, this is called immediately after pci_enable_device.
         * If it returns non-zero, no probing will take place and the
         * ports will not be used. */
        int (*preinit_hook) (struct pci_dev *pdev, int autoirq, int autodma);
 
        /* If set, this is called after probing for ports.  If 'failed'
         * is non-zero we couldn't use any of the ports. */
        void (*postinit_hook) (struct pci_dev *pdev, int failed);
} cards[] __devinitdata = {
        /* siig_1p_10x */               { 1, { { 2, 3 }, } },
        /* siig_2p_10x */               { 2, { { 2, 3 }, { 4, 5 }, } },
        /* siig_1p_20x */               { 1, { { 0, 1 }, } },
        /* siig_2p_20x */               { 2, { { 0, 1 }, { 2, 3 }, } },
        /* lava_parallel */             { 1, { { 0, -1 }, } },
        /* lava_parallel_dual_a */      { 1, { { 0, -1 }, } },
        /* lava_parallel_dual_b */      { 1, { { 0, -1 }, } },
        /* boca_ioppar */               { 1, { { 0, -1 }, } },
        /* plx_9050 */                  { 2, { { 4, -1 }, { 5, -1 }, } },
        /* timedia_4078a */             { 1, { { 2, -1 }, } },
        /* timedia_4079h */             { 1, { { 2, 3 }, } },
        /* timedia_4085h */             { 2, { { 2, -1 }, { 4, -1 }, } },
        /* timedia_4088a */             { 2, { { 2, 3 }, { 4, 5 }, } },
        /* timedia_4089a */             { 2, { { 2, 3 }, { 4, 5 }, } },
        /* timedia_4095a */             { 2, { { 2, 3 }, { 4, 5 }, } },
        /* timedia_4096a */             { 2, { { 2, 3 }, { 4, 5 }, } },
        /* timedia_4078u */             { 1, { { 2, -1 }, } },
        /* timedia_4079a */             { 1, { { 2, 3 }, } },
        /* timedia_4085u */             { 2, { { 2, -1 }, { 4, -1 }, } },
        /* timedia_4079r */             { 1, { { 2, 3 }, } },
        /* timedia_4079s */             { 1, { { 2, 3 }, } },
        /* timedia_4079d */             { 1, { { 2, 3 }, } },
        /* timedia_4079e */             { 1, { { 2, 3 }, } },
        /* timedia_4079f */             { 1, { { 2, 3 }, } },
        /* timedia_9079a */             { 1, { { 2, 3 }, } },
        /* timedia_9079b */             { 1, { { 2, 3 }, } },
        /* timedia_9079c */             { 1, { { 2, 3 }, } },
        /* timedia_4006a */             { 1, { { 0, -1 }, } },
        /* timedia_4014  */             { 2, { { 0, -1 }, { 2, -1 }, } },
        /* timedia_4008a */             { 1, { { 0, 1 }, } },
        /* timedia_4018  */             { 2, { { 0, 1 }, { 2, 3 }, } },
        /* timedia_9018a */             { 2, { { 0, 1 }, { 2, 3 }, } },
                                        /* SYBA uses fixed offsets in
                                           a 1K io window */
        /* syba_2p_epp AP138B */        { 2, { { 0, 0x078 }, { 0, 0x178 }, } },
        /* syba_1p_ecp W83787 */        { 1, { { 0, 0x078 }, } },
        /* titan_010l */                { 1, { { 3, -1 }, } },
        /* titan_1284p2 */              { 2, { { 0, 1 }, { 2, 3 }, } },
        /* avlab_1p             */      { 1, { { 0, 1}, } },
        /* avlab_2p             */      { 2, { { 0, 1}, { 2, 3 },} },
        /* The Oxford Semi cards are unusual: 954 doesn't support ECP,
         * and 840 locks up if you write 1 to bit 2! */
        /* oxsemi_954 */                { 1, { { 0, -1 }, } },
        /* oxsemi_840 */                { 1, { { 0, -1 }, } },
        /* aks_0100 */                  { 1, { { 0, -1 }, } },
        /* mobility_pp */               { 1, { { 0, 1 }, } },
};
 
static struct pci_device_id parport_pc_pci_tbl[] __devinitdata = {
        /* Super-IO onboard chips */
        { 0x1106, 0x0686, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_686a },
        { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_ite_8872 },
 
        /* PCI cards */
        { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_10x,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_10x },
        { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_10x,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_10x },
        { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_20x,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_20x },
        { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_20x,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_20x },
        { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PARALLEL,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel },
        { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_A,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_a },
        { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_B,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_b },
        { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_BOCA_IOPPAR,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, boca_ioppar },
        { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
          PCI_SUBVENDOR_ID_EXSYS, PCI_SUBDEVICE_ID_EXSYS_4014, 0,0, plx_9050 },
        /* PCI_VENDOR_ID_TIMEDIA/SUNIX has many differing cards ...*/
        { 0x1409, 0x7168, 0x1409, 0x4078, 0, 0, timedia_4078a },
        { 0x1409, 0x7168, 0x1409, 0x4079, 0, 0, timedia_4079h },
        { 0x1409, 0x7168, 0x1409, 0x4085, 0, 0, timedia_4085h },
        { 0x1409, 0x7168, 0x1409, 0x4088, 0, 0, timedia_4088a },
        { 0x1409, 0x7168, 0x1409, 0x4089, 0, 0, timedia_4089a },
        { 0x1409, 0x7168, 0x1409, 0x4095, 0, 0, timedia_4095a },
        { 0x1409, 0x7168, 0x1409, 0x4096, 0, 0, timedia_4096a },
        { 0x1409, 0x7168, 0x1409, 0x5078, 0, 0, timedia_4078u },
        { 0x1409, 0x7168, 0x1409, 0x5079, 0, 0, timedia_4079a },
        { 0x1409, 0x7168, 0x1409, 0x5085, 0, 0, timedia_4085u },
        { 0x1409, 0x7168, 0x1409, 0x6079, 0, 0, timedia_4079r },
        { 0x1409, 0x7168, 0x1409, 0x7079, 0, 0, timedia_4079s },
        { 0x1409, 0x7168, 0x1409, 0x8079, 0, 0, timedia_4079d },
        { 0x1409, 0x7168, 0x1409, 0x9079, 0, 0, timedia_4079e },
        { 0x1409, 0x7168, 0x1409, 0xa079, 0, 0, timedia_4079f },
        { 0x1409, 0x7168, 0x1409, 0xb079, 0, 0, timedia_9079a },
        { 0x1409, 0x7168, 0x1409, 0xc079, 0, 0, timedia_9079b },
        { 0x1409, 0x7168, 0x1409, 0xd079, 0, 0, timedia_9079c },
        { 0x1409, 0x7268, 0x1409, 0x0101, 0, 0, timedia_4006a },
        { 0x1409, 0x7268, 0x1409, 0x0102, 0, 0, timedia_4014 },
        { 0x1409, 0x7268, 0x1409, 0x0103, 0, 0, timedia_4008a },
        { 0x1409, 0x7268, 0x1409, 0x0104, 0, 0, timedia_4018 },
        { 0x1409, 0x7268, 0x1409, 0x9018, 0, 0, timedia_9018a },
        { 0x14f2, 0x0121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, mobility_pp },
        { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_2P_EPP,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_2p_epp },
        { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_1P_ECP,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_1p_ecp },
        { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_010L,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_010l },
        { 0x9710, 0x9815, 0x1000, 0x0020, 0, 0, titan_1284p2 },
        /* PCI_VENDOR_ID_AVLAB/Intek21 has another bunch of cards ...*/
        { 0x14db, 0x2120, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1p}, /* AFAVLAB_TK9902 */
        { 0x14db, 0x2121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2p},
        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954PP,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_954 },
        { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_12PCI840,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_840 },
        { PCI_VENDOR_ID_AKS, PCI_DEVICE_ID_AKS_ALADDINCARD,
          PCI_ANY_ID, PCI_ANY_ID, 0, 0, aks_0100 },
        { 0, } /* terminate list */
};
MODULE_DEVICE_TABLE(pci,parport_pc_pci_tbl);
 
static int __devinit parport_pc_pci_probe (struct pci_dev *dev,
                                           const struct pci_device_id *id)
{
        int err, count, n, i = id->driver_data;
        if (i < last_sio)
                /* This is an onboard Super-IO and has already been probed */
                return 0;
 
        /* This is a PCI card */
        i -= last_sio;
        count = 0;
        if ((err = pci_enable_device (dev)) != 0)
                return err;
 
        if (cards[i].preinit_hook &&
            cards[i].preinit_hook (dev, PARPORT_IRQ_NONE, PARPORT_DMA_NONE))
                return -ENODEV;
 
        for (n = 0; n < cards[i].numports; n++) {
                int lo = cards[i].addr[n].lo;
                int hi = cards[i].addr[n].hi;
                unsigned long io_lo, io_hi;
                io_lo = pci_resource_start (dev, lo);
                io_hi = 0;
                if ((hi >= 0) && (hi <= 6))
                        io_hi = pci_resource_start (dev, hi);
                else if (hi > 6)
                        io_lo += hi; /* Reinterpret the meaning of
                                        "hi" as an offset (see SYBA
                                        def.) */
                /* TODO: test if sharing interrupts works */
                printk (KERN_DEBUG "PCI parallel port detected: %04x:%04x, "
                        "I/O at %#lx(%#lx)\n",
                        parport_pc_pci_tbl[i + last_sio].vendor,
                        parport_pc_pci_tbl[i + last_sio].device, io_lo, io_hi);
                if (parport_pc_probe_port (io_lo, io_hi, PARPORT_IRQ_NONE,
                                           PARPORT_DMA_NONE, dev))
                        count++;
        }
 
        if (cards[i].postinit_hook)
                cards[i].postinit_hook (dev, count == 0);
 
        return count == 0 ? -ENODEV : 0;
}
 
static struct pci_driver parport_pc_pci_driver = {
        name:           "parport_pc",
        id_table:       parport_pc_pci_tbl,
        probe:          parport_pc_pci_probe,
};
 
static int __init parport_pc_init_superio (int autoirq, int autodma)
{
        const struct pci_device_id *id;
        struct pci_dev *pdev;
        int ret = 0;
 
        pci_for_each_dev(pdev) {
                id = pci_match_device (parport_pc_pci_tbl, pdev);
                if (id == NULL || id->driver_data >= last_sio)
                        continue;
 
                if (parport_pc_superio_info[id->driver_data].probe
                        (pdev, autoirq, autodma)) {
                        ret++;
                }
        }
 
        return ret; /* number of devices found */
}
#else
static struct pci_driver parport_pc_pci_driver;
static int __init parport_pc_init_superio(int autoirq, int autodma) {return 0;}
#endif /* CONFIG_PCI */
 
/* This is called by parport_pc_find_nonpci_ports (in asm/parport.h) */
static int __init __attribute__((unused))
parport_pc_find_isa_ports (int autoirq, int autodma)
{
        int count = 0;
 
        if (parport_pc_probe_port(0x3bc, 0x7bc, autoirq, autodma, NULL))
                count++;
        if (parport_pc_probe_port(0x378, 0x778, autoirq, autodma, NULL))
                count++;
        if (parport_pc_probe_port(0x278, 0x678, autoirq, autodma, NULL))
                count++;
 
        return count;
}
 
/* This function is called by parport_pc_init if the user didn't
 * specify any ports to probe.  Its job is to find some ports.  Order
 * is important here -- we want ISA ports to be registered first,
 * followed by PCI cards (for least surprise), but before that we want
 * to do chipset-specific tests for some onboard ports that we know
 * about.
 *
 * autoirq is PARPORT_IRQ_NONE, PARPORT_IRQ_AUTO, or PARPORT_IRQ_PROBEONLY
 * autodma is PARPORT_DMA_NONE or PARPORT_DMA_AUTO
 */
static int __init parport_pc_find_ports (int autoirq, int autodma)
{
        int count = 0, r;
 
#ifdef CONFIG_PARPORT_PC_SUPERIO
        detect_and_report_winbond ();
        detect_and_report_smsc ();
#endif
 
        /* Onboard SuperIO chipsets that show themselves on the PCI bus. */
        count += parport_pc_init_superio (autoirq, autodma);
 
        /* ISA ports and whatever (see asm/parport.h). */
        count += parport_pc_find_nonpci_ports (autoirq, autodma);
 
        r = pci_register_driver (&parport_pc_pci_driver);
        if (r >= 0) {
                registered_parport = 1;
                count += r;
        }
 
        return count;
}
 
int __init parport_pc_init (int *io, int *io_hi, int *irq, int *dma)
{
        int count = 0, i = 0;
 
        if (io && *io) {
                /* Only probe the ports we were given. */
                user_specified = 1;
                do {
                        if ((*io_hi) == PARPORT_IOHI_AUTO)
                               *io_hi = 0x400 + *io;
                        if (parport_pc_probe_port(*(io++), *(io_hi++),
                                                  *(irq++), *(dma++), NULL))
                                count++;
                } while (*io && (++i < PARPORT_PC_MAX_PORTS));
        } else {
                count += parport_pc_find_ports (irq[0], dma[0]);
        }
 
        return count;
}
 
/* Exported symbols. */
EXPORT_SYMBOL (parport_pc_probe_port);
EXPORT_SYMBOL (parport_pc_unregister_port);
 
#ifdef MODULE
static int io[PARPORT_PC_MAX_PORTS+1] = { [0 ... PARPORT_PC_MAX_PORTS] = 0 };
static int io_hi[PARPORT_PC_MAX_PORTS+1] =
        { [0 ... PARPORT_PC_MAX_PORTS] = PARPORT_IOHI_AUTO };
static int dmaval[PARPORT_PC_MAX_PORTS] = { [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_DMA_NONE };
static int irqval[PARPORT_PC_MAX_PORTS] = { [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_IRQ_PROBEONLY };
static const char *irq[PARPORT_PC_MAX_PORTS] = { NULL, };
static const char *dma[PARPORT_PC_MAX_PORTS] = { NULL, };
 
MODULE_AUTHOR("Phil Blundell, Tim Waugh, others");
MODULE_DESCRIPTION("PC-style parallel port driver");
MODULE_LICENSE("GPL");
 
MODULE_PARM_DESC(io, "Base I/O address (SPP regs)");
MODULE_PARM(io, "1-" __MODULE_STRING(PARPORT_PC_MAX_PORTS) "i");
MODULE_PARM_DESC(io_hi, "Base I/O address (ECR)");
MODULE_PARM(io_hi, "1-" __MODULE_STRING(PARPORT_PC_MAX_PORTS) "i");
MODULE_PARM_DESC(irq, "IRQ line");
MODULE_PARM(irq, "1-" __MODULE_STRING(PARPORT_PC_MAX_PORTS) "s");
MODULE_PARM_DESC(dma, "DMA channel");
MODULE_PARM(dma, "1-" __MODULE_STRING(PARPORT_PC_MAX_PORTS) "s");
#if defined(CONFIG_PARPORT_PC_FIFO) || defined(CONFIG_PARPORT_PC_SUPERIO)
MODULE_PARM_DESC(verbose_probing, "Log chit-chat during initialisation");
MODULE_PARM(verbose_probing, "i");
#endif
 
int init_module(void)
{
        /* Work out how many ports we have, then get parport_share to parse
           the irq values. */
        unsigned int i;
        int ret;
        for (i = 0; i < PARPORT_PC_MAX_PORTS && io[i]; i++);
        if (i) {
                if (parport_parse_irqs(i, irq, irqval)) return 1;
                if (parport_parse_dmas(i, dma, dmaval)) return 1;
        }
        else {
                /* The user can make us use any IRQs or DMAs we find. */
                int val;
 
                if (irq[0] && !parport_parse_irqs (1, irq, &val))
                        switch (val) {
                        case PARPORT_IRQ_NONE:
                        case PARPORT_IRQ_AUTO:
                                irqval[0] = val;
                                break;
                        default:
                                printk (KERN_WARNING
                                        "parport_pc: irq specified "
                                        "without base address.  Use 'io=' "
                                        "to specify one\n");
                        }
 
                if (dma[0] && !parport_parse_dmas (1, dma, &val))
                        switch (val) {
                        case PARPORT_DMA_NONE:
                        case PARPORT_DMA_AUTO:
                                dmaval[0] = val;
                                break;
                        default:
                                printk (KERN_WARNING
                                        "parport_pc: dma specified "
                                        "without base address.  Use 'io=' "
                                        "to specify one\n");
                        }
        }
 
        ret = !parport_pc_init (io, io_hi, irqval, dmaval);
        if (ret && registered_parport)
                pci_unregister_driver (&parport_pc_pci_driver);
 
        return ret;
}
 
void cleanup_module(void)
{
        /* We ought to keep track of which ports are actually ours. */
        struct parport *p = parport_enumerate(), *tmp;
 
        if (!user_specified)
                pci_unregister_driver (&parport_pc_pci_driver);
 
        while (p) {
                tmp = p->next;
                if (p->modes & PARPORT_MODE_PCSPP)
                        parport_pc_unregister_port (p);
 
                p = tmp;
        }
}
#endif
Browse

Tools

Subversion Repositories or1k

[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [parport/] [parport_pc.c] - Blame information for rev 1765

Line No.	Rev	Author	Line
1	1275	phoenix	`/* Low-level parallel-port routines for 8255-based PC-style hardware.`
2			`*`
3			`* Authors: Phil Blundell <Philip.Blundell@pobox.com>`
4			`* Tim Waugh <tim@cyberelk.demon.co.uk>`
5			`* Jose Renau <renau@acm.org>`
6			`* David Campbell <campbell@torque.net>`
7			`* Andrea Arcangeli`
8			`*`
9			`* based on work by Grant Guenther <grant@torque.net> and Phil Blundell.`
10			`*`
11			`* Cleaned up include files - Russell King <linux@arm.uk.linux.org>`
12			`* DMA support - Bert De Jonghe <bert@sophis.be>`
13			`* Many ECP bugs fixed. Fred Barnes & Jamie Lokier, 1999`
14			`* More PCI support now conditional on CONFIG_PCI, 03/2001, Paul G.`
15			`* Various hacks, Fred Barnes, 04/2001`
16			`*/`
17
18			`/* This driver should work with any hardware that is broadly compatible`
19			`* with that in the IBM PC. This applies to the majority of integrated`
20			`* I/O chipsets that are commonly available. The expected register`
21			`* layout is:`
22			`*`
23			`* base+0 data`
24			`* base+1 status`
25			`* base+2 control`
26			`*`
27			`* In addition, there are some optional registers:`
28			`*`
29			`* base+3 EPP address`
30			`* base+4 EPP data`
31			`* base+0x400 ECP config A`
32			`* base+0x401 ECP config B`
33			`* base+0x402 ECP control`
34			`*`
35			`* All registers are 8 bits wide and read/write. If your hardware differs`
36			`* only in register addresses (eg because your registers are on 32-bit`
37			`* word boundaries) then you can alter the constants in parport_pc.h to`
38			`* accomodate this.`
39			`*`
40			`* Note that the ECP registers may not start at offset 0x400 for PCI cards,`