URL https://opencores.org/ocsvn/or1k/or1k/trunk

Subversion Repositories or1k

[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [pcmcia/] [au1000_pb1x00.c] - Blame information for rev 1774

Go to most recent revision | Details | Compare with Previous | View Log


/*
 *
 * Alchemy Semi Pb1x00 boards specific pcmcia routines.
 *
 * Copyright 2002 MontaVista Software Inc.
 * Author: MontaVista Software, Inc.
 *              ppopov@mvista.com or source@mvista.com
 *
 * ########################################################################
 *
 *  This program is free software; you can distribute it and/or modify it
 *  under the terms of the GNU General Public License (Version 2) as
 *  published by the Free Software Foundation.
 *
 *  This program is distributed in the hope it will be useful, but WITHOUT
 *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
 *  for more details.
 *
 *  You should have received a copy of the GNU General Public License along
 *  with this program; if not, write to the Free Software Foundation, Inc.,
 *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
 */
#include <linux/module.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/ioport.h>
#include <linux/kernel.h>
#include <linux/tqueue.h>
#include <linux/timer.h>
#include <linux/mm.h>
#include <linux/proc_fs.h>
#include <linux/version.h>
#include <linux/types.h>
 
#include <pcmcia/version.h>
#include <pcmcia/cs_types.h>
#include <pcmcia/cs.h>
#include <pcmcia/ss.h>
#include <pcmcia/bulkmem.h>
#include <pcmcia/cistpl.h>
#include <pcmcia/bus_ops.h>
#include "cs_internal.h"
 
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
 
#include <asm/au1000.h>
#include <asm/au1000_pcmcia.h>
 
#ifdef CONFIG_MIPS_PB1000
#include <asm/pb1000.h>
#define PCMCIA_IRQ AU1000_GPIO_15
#elif defined (CONFIG_MIPS_PB1500)
#include <asm/pb1500.h>
#define PCMCIA_IRQ AU1500_GPIO_203
#elif defined (CONFIG_MIPS_PB1100)
#include <asm/pb1100.h>
#define PCMCIA_IRQ AU1000_GPIO_11
#endif
 
static int pb1x00_pcmcia_init(struct pcmcia_init *init)
{
#ifdef CONFIG_MIPS_PB1000
        u16 pcr;
        pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
 
        au_writel(0x8000, PB1000_MDR); /* clear pcmcia interrupt */
        au_sync_delay(100);
        au_writel(0x4000, PB1000_MDR); /* enable pcmcia interrupt */
        au_sync();
 
        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
        au_writel(pcr, PB1000_PCR);
        au_sync_delay(20);
 
        return PCMCIA_NUM_SOCKS;
 
#else /* fixme -- take care of the Pb1500 at some point */
 
        u16 pcr;
        pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
        pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
        au_writew(pcr, PCMCIA_BOARD_REG);
        au_sync_delay(500);
        return PCMCIA_NUM_SOCKS;
#endif
}
 
static int pb1x00_pcmcia_shutdown(void)
{
#ifdef CONFIG_MIPS_PB1000
        u16 pcr;
        pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);
        au_writel(pcr, PB1000_PCR);
        au_sync_delay(20);
        return 0;
#else
        u16 pcr;
        pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
        pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
        au_writew(pcr, PCMCIA_BOARD_REG);
        au_sync_delay(2);
        return 0;
#endif
}
 
static int
pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
{
        u32 inserted0, inserted1;
        u16 vs0, vs1;
 
#ifdef CONFIG_MIPS_PB1000
        vs0 = vs1 = (u16)au_readl(PB1000_ACR1);
        inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 | ACR1_SLOT_0_CD2));
        inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 | ACR1_SLOT_1_CD2));
        vs0 = (vs0 >> 4) & 0x3;
        vs1 = (vs1 >> 12) & 0x3;
#else
        vs0 = (au_readw(BOARD_STATUS_REG) >> 4) & 0x3;
#ifdef CONFIG_MIPS_PB1500
        inserted0 = !((au_readl(GPIO2_PINSTATE) >> 1) & 0x1); /* gpio 201 */
#else /* Pb1100 */
        inserted0 = !((au_readl(SYS_PINSTATERD) >> 9) & 0x1); /* gpio 9 */
#endif
        inserted1 = 0;
#endif
 
        state->ready = 0;
        state->vs_Xv = 0;
        state->vs_3v = 0;
        state->detect = 0;
 
        if (sock == 0) {
                if (inserted0) {
                        switch (vs0) {
                                case 0:
                                case 2:
                                        state->vs_3v=1;
                                        break;
                                case 3: /* 5V */
                                        break;
                                default:
                                        /* return without setting 'detect' */
                                        printk(KERN_ERR "pb1x00 bad VS (%d)\n",
                                                        vs0);
                                        return 0;
                        }
                        state->detect = 1;
                }
        }
        else  {
                if (inserted1) {
                        switch (vs1) {
                                case 0:
                                case 2:
                                        state->vs_3v=1;
                                        break;
                                case 3: /* 5V */
                                        break;
                                default:
                                        /* return without setting 'detect' */
                                        printk(KERN_ERR "pb1x00 bad VS (%d)\n",
                                                        vs1);
                                        return 0;
                        }
                        state->detect = 1;
                }
        }
 
        if (state->detect) {
                state->ready = 1;
        }
 
        state->bvd1=1;
        state->bvd2=1;
        state->wrprot=0;
        return 1;
}
 
 
static int pb1x00_pcmcia_get_irq_info(struct pcmcia_irq_info *info)
{
 
        if(info->sock > PCMCIA_MAX_SOCK) return -1;
 
        /*
         * Even in the case of the Pb1000, both sockets are connected
         * to the same irq line.
         */
        info->irq = PCMCIA_IRQ;
 
        return 0;
}
 
 
static int
pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
{
        u16 pcr;
 
        if(configure->sock > PCMCIA_MAX_SOCK) return -1;
 
#ifdef CONFIG_MIPS_PB1000
        pcr = au_readl(PB1000_PCR);
 
        if (configure->sock == 0) {
                pcr &= ~(PCR_SLOT_0_VCC0 | PCR_SLOT_0_VCC1 |
                                PCR_SLOT_0_VPP0 | PCR_SLOT_0_VPP1);
        }
        else  {
                pcr &= ~(PCR_SLOT_1_VCC0 | PCR_SLOT_1_VCC1 |
                                PCR_SLOT_1_VPP0 | PCR_SLOT_1_VPP1);
        }
 
        pcr &= ~PCR_SLOT_0_RST;
        DEBUG(KERN_INFO "Vcc %dV Vpp %dV, pcr %x\n",
                        configure->vcc, configure->vpp, pcr);
        switch(configure->vcc){
                case 0:  /* Vcc 0 */
                        switch(configure->vpp) {
                                case 0:
                                        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_GND,
                                                        configure->sock);
                                        break;
                                case 12:
                                        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_12V,
                                                        configure->sock);
                                        break;
                                case 50:
                                        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_5V,
                                                        configure->sock);
                                        break;
                                case 33:
                                        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_3V,
                                                        configure->sock);
                                        break;
                                default:
                                        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
                                                        configure->sock);
                                        printk("%s: bad Vcc/Vpp (%d:%d)\n",
                                                        __FUNCTION__,
                                                        configure->vcc,
                                                        configure->vpp);
                                        break;
                        }
                        break;
                case 50: /* Vcc 5V */
                        switch(configure->vpp) {
                                case 0:
                                        pcr |= SET_VCC_VPP(VCC_5V,VPP_GND,
                                                        configure->sock);
                                        break;
                                case 50:
                                        pcr |= SET_VCC_VPP(VCC_5V,VPP_5V,
                                                        configure->sock);
                                        break;
                                case 12:
                                        pcr |= SET_VCC_VPP(VCC_5V,VPP_12V,
                                                        configure->sock);
                                        break;
                                case 33:
                                        pcr |= SET_VCC_VPP(VCC_5V,VPP_3V,
                                                        configure->sock);
                                        break;
                                default:
                                        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
                                                        configure->sock);
                                        printk("%s: bad Vcc/Vpp (%d:%d)\n",
                                                        __FUNCTION__,
                                                        configure->vcc,
                                                        configure->vpp);
                                        break;
                        }
                        break;
                case 33: /* Vcc 3.3V */
                        switch(configure->vpp) {
                                case 0:
                                        pcr |= SET_VCC_VPP(VCC_3V,VPP_GND,
                                                        configure->sock);
                                        break;
                                case 50:
                                        pcr |= SET_VCC_VPP(VCC_3V,VPP_5V,
                                                        configure->sock);
                                        break;
                                case 12:
                                        pcr |= SET_VCC_VPP(VCC_3V,VPP_12V,
                                                        configure->sock);
                                        break;
                                case 33:
                                        pcr |= SET_VCC_VPP(VCC_3V,VPP_3V,
                                                        configure->sock);
                                        break;
                                default:
                                        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,
                                                        configure->sock);
                                        printk("%s: bad Vcc/Vpp (%d:%d)\n",
                                                        __FUNCTION__,
                                                        configure->vcc,
                                                        configure->vpp);
                                        break;
                        }
                        break;
                default: /* what's this ? */
                        pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,configure->sock);
                        printk(KERN_ERR "%s: bad Vcc %d\n",
                                        __FUNCTION__, configure->vcc);
                        break;
        }
 
        if (configure->sock == 0) {
        pcr &= ~(PCR_SLOT_0_RST);
                if (configure->reset)
                pcr |= PCR_SLOT_0_RST;
        }
        else {
                pcr &= ~(PCR_SLOT_1_RST);
                if (configure->reset)
                        pcr |= PCR_SLOT_1_RST;
        }
        au_writel(pcr, PB1000_PCR);
        au_sync_delay(300);
 
#else
 
        pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf;
 
        DEBUG(KERN_INFO "Vcc %dV Vpp %dV, pcr %x, reset %d\n",
                        configure->vcc, configure->vpp, pcr, configure->reset);
 
 
        switch(configure->vcc){
                case 0:  /* Vcc 0 */
                        pcr |= SET_VCC_VPP(0,0);
                        break;
                case 50: /* Vcc 5V */
                        switch(configure->vpp) {
                                case 0:
                                        pcr |= SET_VCC_VPP(2,0);
                                        break;
                                case 50:
                                        pcr |= SET_VCC_VPP(2,1);
                                        break;
                                case 12:
                                        pcr |= SET_VCC_VPP(2,2);
                                        break;
                                case 33:
                                default:
                                        pcr |= SET_VCC_VPP(0,0);
                                        printk("%s: bad Vcc/Vpp (%d:%d)\n",
                                                        __FUNCTION__,
                                                        configure->vcc,
                                                        configure->vpp);
                                        break;
                        }
                        break;
                case 33: /* Vcc 3.3V */
                        switch(configure->vpp) {
                                case 0:
                                        pcr |= SET_VCC_VPP(1,0);
                                        break;
                                case 12:
                                        pcr |= SET_VCC_VPP(1,2);
                                        break;
                                case 33:
                                        pcr |= SET_VCC_VPP(1,1);
                                        break;
                                case 50:
                                default:
                                        pcr |= SET_VCC_VPP(0,0);
                                        printk("%s: bad Vcc/Vpp (%d:%d)\n",
                                                        __FUNCTION__,
                                                        configure->vcc,
                                                        configure->vpp);
                                        break;
                        }
                        break;
                default: /* what's this ? */
                        pcr |= SET_VCC_VPP(0,0);
                        printk(KERN_ERR "%s: bad Vcc %d\n",
                                        __FUNCTION__, configure->vcc);
                        break;
        }
 
        au_writew(pcr, PCMCIA_BOARD_REG);
        au_sync_delay(300);
 
        if (!configure->reset) {
                pcr |= PC_DRV_EN;
                au_writew(pcr, PCMCIA_BOARD_REG);
                au_sync_delay(100);
                pcr |= PC_DEASSERT_RST;
                au_writew(pcr, PCMCIA_BOARD_REG);
                au_sync_delay(100);
        }
        else {
                pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
                au_writew(pcr, PCMCIA_BOARD_REG);
                au_sync_delay(100);
        }
#endif
        return 0;
}
 
 
struct pcmcia_low_level pb1x00_pcmcia_ops = {
        pb1x00_pcmcia_init,
        pb1x00_pcmcia_shutdown,
        pb1x00_pcmcia_socket_state,
        pb1x00_pcmcia_get_irq_info,
        pb1x00_pcmcia_configure_socket
};

Browse

Tools

Subversion Repositories or1k

[/] [or1k/] [trunk/] [linux/] [linux-2.4/] [drivers/] [pcmcia/] [au1000_pb1x00.c] - Blame information for rev 1774

Line No.	Rev	Author	Line
1	1275	phoenix	`/*`
2			`*`
3			`* Alchemy Semi Pb1x00 boards specific pcmcia routines.`
4			`*`
5			`* Copyright 2002 MontaVista Software Inc.`
6			`* Author: MontaVista Software, Inc.`
7			`* ppopov@mvista.com or source@mvista.com`
8			`*`
9			`* ########################################################################`
10			`*`
11			`* This program is free software; you can distribute it and/or modify it`
12			`* under the terms of the GNU General Public License (Version 2) as`
13			`* published by the Free Software Foundation.`
14			`*`
15			`* This program is distributed in the hope it will be useful, but WITHOUT`
16			`* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or`
17			`* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License`
18			`* for more details.`
19			`*`
20			`* You should have received a copy of the GNU General Public License along`
21			`* with this program; if not, write to the Free Software Foundation, Inc.,`
22			`* 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.`
23			`*/`
24			`#include <linux/module.h>`
25			`#include <linux/init.h>`
26			`#include <linux/delay.h>`
27			`#include <linux/ioport.h>`
28			`#include <linux/kernel.h>`
29			`#include <linux/tqueue.h>`
30			`#include <linux/timer.h>`
31			`#include <linux/mm.h>`
32			`#include <linux/proc_fs.h>`
33			`#include <linux/version.h>`
34			`#include <linux/types.h>`
35
36			`#include <pcmcia/version.h>`
37			`#include <pcmcia/cs_types.h>`
38			`#include <pcmcia/cs.h>`
39			`#include <pcmcia/ss.h>`
40			`#include <pcmcia/bulkmem.h>`
41			`#include <pcmcia/cistpl.h>`
42			`#include <pcmcia/bus_ops.h>`
43			`#include "cs_internal.h"`
44
45			`#include <asm/io.h>`
46			`#include <asm/irq.h>`
47			`#include <asm/system.h>`
48
49			`#include <asm/au1000.h>`
50			`#include <asm/au1000_pcmcia.h>`
51
52			`#ifdef CONFIG_MIPS_PB1000`
53			`#include <asm/pb1000.h>`
54			`#define PCMCIA_IRQ AU1000_GPIO_15`
55			`#elif defined (CONFIG_MIPS_PB1500)`
56			`#include <asm/pb1500.h>`
57			`#define PCMCIA_IRQ AU1500_GPIO_203`
58			`#elif defined (CONFIG_MIPS_PB1100)`
59			`#include <asm/pb1100.h>`
60			`#define PCMCIA_IRQ AU1000_GPIO_11`
61			`#endif`
62
63			`static int pb1x00_pcmcia_init(struct pcmcia_init *init)`
64			`{`
65			`#ifdef CONFIG_MIPS_PB1000`
66			`u16 pcr;`
67			`pcr = PCR_SLOT_0_RST \| PCR_SLOT_1_RST;`
68
69			`au_writel(0x8000, PB1000_MDR); /* clear pcmcia interrupt */`
70			`au_sync_delay(100);`
71			`au_writel(0x4000, PB1000_MDR); /* enable pcmcia interrupt */`
72			`au_sync();`
73
74			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);`
75			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);`
76			`au_writel(pcr, PB1000_PCR);`
77			`au_sync_delay(20);`
78
79			`return PCMCIA_NUM_SOCKS;`
80
81			`#else /* fixme -- take care of the Pb1500 at some point */`
82
83			`u16 pcr;`
84			`pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */`
85			`pcr &= ~(PC_DEASSERT_RST \| PC_DRV_EN);`
86			`au_writew(pcr, PCMCIA_BOARD_REG);`
87			`au_sync_delay(500);`
88			`return PCMCIA_NUM_SOCKS;`
89			`#endif`
90			`}`
91
92			`static int pb1x00_pcmcia_shutdown(void)`
93			`{`
94			`#ifdef CONFIG_MIPS_PB1000`
95			`u16 pcr;`
96			`pcr = PCR_SLOT_0_RST \| PCR_SLOT_1_RST;`
97			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);`
98			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,1);`
99			`au_writel(pcr, PB1000_PCR);`
100			`au_sync_delay(20);`
101			`return 0;`
102			`#else`
103			`u16 pcr;`
104			`pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */`
105			`pcr &= ~(PC_DEASSERT_RST \| PC_DRV_EN);`
106			`au_writew(pcr, PCMCIA_BOARD_REG);`
107			`au_sync_delay(2);`
108			`return 0;`
109			`#endif`
110			`}`
111
112			`static int`
113			`pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)`
114			`{`
115			`u32 inserted0, inserted1;`
116			`u16 vs0, vs1;`
117
118			`#ifdef CONFIG_MIPS_PB1000`
119			`vs0 = vs1 = (u16)au_readl(PB1000_ACR1);`
120			`inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 \| ACR1_SLOT_0_CD2));`
121			`inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 \| ACR1_SLOT_1_CD2));`
122			`vs0 = (vs0 >> 4) & 0x3;`
123			`vs1 = (vs1 >> 12) & 0x3;`
124			`#else`
125			`vs0 = (au_readw(BOARD_STATUS_REG) >> 4) & 0x3;`
126			`#ifdef CONFIG_MIPS_PB1500`
127			`inserted0 = !((au_readl(GPIO2_PINSTATE) >> 1) & 0x1); /* gpio 201 */`
128			`#else /* Pb1100 */`
129			`inserted0 = !((au_readl(SYS_PINSTATERD) >> 9) & 0x1); /* gpio 9 */`
130			`#endif`
131			`inserted1 = 0;`
132			`#endif`
133
134			`state->ready = 0;`
135			`state->vs_Xv = 0;`
136			`state->vs_3v = 0;`
137			`state->detect = 0;`
138
139			`if (sock == 0) {`
140			`if (inserted0) {`
141			`switch (vs0) {`
142			`case 0:`
143			`case 2:`
144			`state->vs_3v=1;`
145			`break;`
146			`case 3: /* 5V */`
147			`break;`
148			`default:`
149			`/* return without setting 'detect' */`
150			`printk(KERN_ERR "pb1x00 bad VS (%d)\n",`
151			`vs0);`
152			`return 0;`
153			`}`
154			`state->detect = 1;`
155			`}`
156			`}`
157			`else {`
158			`if (inserted1) {`
159			`switch (vs1) {`
160			`case 0:`
161			`case 2:`
162			`state->vs_3v=1;`
163			`break;`
164			`case 3: /* 5V */`
165			`break;`
166			`default:`
167			`/* return without setting 'detect' */`
168			`printk(KERN_ERR "pb1x00 bad VS (%d)\n",`
169			`vs1);`
170			`return 0;`
171			`}`
172			`state->detect = 1;`
173			`}`
174			`}`
175
176			`if (state->detect) {`
177			`state->ready = 1;`
178			`}`
179
180			`state->bvd1=1;`
181			`state->bvd2=1;`
182			`state->wrprot=0;`
183			`return 1;`
184			`}`
185
186
187			`static int pb1x00_pcmcia_get_irq_info(struct pcmcia_irq_info *info)`
188			`{`
189
190			`if(info->sock > PCMCIA_MAX_SOCK) return -1;`
191
192			`/*`
193			`* Even in the case of the Pb1000, both sockets are connected`
194			`* to the same irq line.`
195			`*/`
196			`info->irq = PCMCIA_IRQ;`
197
198			`return 0;`
199			`}`
200
201
202			`static int`
203			`pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)`
204			`{`
205			`u16 pcr;`
206
207			`if(configure->sock > PCMCIA_MAX_SOCK) return -1;`
208
209			`#ifdef CONFIG_MIPS_PB1000`
210			`pcr = au_readl(PB1000_PCR);`
211
212			`if (configure->sock == 0) {`
213			`pcr &= ~(PCR_SLOT_0_VCC0 \| PCR_SLOT_0_VCC1 \|`
214			`PCR_SLOT_0_VPP0 \| PCR_SLOT_0_VPP1);`
215			`}`
216			`else {`
217			`pcr &= ~(PCR_SLOT_1_VCC0 \| PCR_SLOT_1_VCC1 \|`
218			`PCR_SLOT_1_VPP0 \| PCR_SLOT_1_VPP1);`
219			`}`
220
221			`pcr &= ~PCR_SLOT_0_RST;`
222			`DEBUG(KERN_INFO "Vcc %dV Vpp %dV, pcr %x\n",`
223			`configure->vcc, configure->vpp, pcr);`
224			`switch(configure->vcc){`
225			`case 0: /* Vcc 0 */`
226			`switch(configure->vpp) {`
227			`case 0:`
228			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_GND,`
229			`configure->sock);`
230			`break;`
231			`case 12:`
232			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_12V,`
233			`configure->sock);`
234			`break;`
235			`case 50:`
236			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_5V,`
237			`configure->sock);`
238			`break;`
239			`case 33:`
240			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_3V,`
241			`configure->sock);`
242			`break;`
243			`default:`
244			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,`
245			`configure->sock);`
246			`printk("%s: bad Vcc/Vpp (%d:%d)\n",`
247			`__FUNCTION__,`
248			`configure->vcc,`
249			`configure->vpp);`
250			`break;`
251			`}`
252			`break;`
253			`case 50: /* Vcc 5V */`
254			`switch(configure->vpp) {`
255			`case 0:`
256			`pcr \|= SET_VCC_VPP(VCC_5V,VPP_GND,`
257			`configure->sock);`
258			`break;`
259			`case 50:`
260			`pcr \|= SET_VCC_VPP(VCC_5V,VPP_5V,`
261			`configure->sock);`
262			`break;`
263			`case 12:`
264			`pcr \|= SET_VCC_VPP(VCC_5V,VPP_12V,`
265			`configure->sock);`
266			`break;`
267			`case 33:`
268			`pcr \|= SET_VCC_VPP(VCC_5V,VPP_3V,`
269			`configure->sock);`
270			`break;`
271			`default:`
272			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,`
273			`configure->sock);`
274			`printk("%s: bad Vcc/Vpp (%d:%d)\n",`
275			`__FUNCTION__,`
276			`configure->vcc,`
277			`configure->vpp);`
278			`break;`
279			`}`
280			`break;`
281			`case 33: /* Vcc 3.3V */`
282			`switch(configure->vpp) {`
283			`case 0:`
284			`pcr \|= SET_VCC_VPP(VCC_3V,VPP_GND,`
285			`configure->sock);`
286			`break;`
287			`case 50:`
288			`pcr \|= SET_VCC_VPP(VCC_3V,VPP_5V,`
289			`configure->sock);`
290			`break;`
291			`case 12:`
292			`pcr \|= SET_VCC_VPP(VCC_3V,VPP_12V,`
293			`configure->sock);`
294			`break;`
295			`case 33:`
296			`pcr \|= SET_VCC_VPP(VCC_3V,VPP_3V,`
297			`configure->sock);`
298			`break;`
299			`default:`
300			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,`
301			`configure->sock);`
302			`printk("%s: bad Vcc/Vpp (%d:%d)\n",`
303			`__FUNCTION__,`
304			`configure->vcc,`
305			`configure->vpp);`
306			`break;`
307			`}`
308			`break;`
309			`default: /* what's this ? */`
310			`pcr \|= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,configure->sock);`
311			`printk(KERN_ERR "%s: bad Vcc %d\n",`
312			`__FUNCTION__, configure->vcc);`
313			`break;`
314			`}`
315
316			`if (configure->sock == 0) {`
317			`pcr &= ~(PCR_SLOT_0_RST);`
318			`if (configure->reset)`
319			`pcr \|= PCR_SLOT_0_RST;`
320			`}`
321			`else {`
322			`pcr &= ~(PCR_SLOT_1_RST);`
323			`if (configure->reset)`
324			`pcr \|= PCR_SLOT_1_RST;`
325			`}`
326			`au_writel(pcr, PB1000_PCR);`
327			`au_sync_delay(300);`
328
329			`#else`
330
331			`pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf;`
332
333			`DEBUG(KERN_INFO "Vcc %dV Vpp %dV, pcr %x, reset %d\n",`
334			`configure->vcc, configure->vpp, pcr, configure->reset);`
335
336
337			`switch(configure->vcc){`
338			`case 0: /* Vcc 0 */`
339			`pcr \|= SET_VCC_VPP(0,0);`
340			`break;`
341			`case 50: /* Vcc 5V */`
342			`switch(configure->vpp) {`
343			`case 0:`
344			`pcr \|= SET_VCC_VPP(2,0);`
345			`break;`
346			`case 50:`
347			`pcr \|= SET_VCC_VPP(2,1);`
348			`break;`
349			`case 12:`
350			`pcr \|= SET_VCC_VPP(2,2);`
351			`break;`
352			`case 33:`
353			`default:`
354			`pcr \|= SET_VCC_VPP(0,0);`
355			`printk("%s: bad Vcc/Vpp (%d:%d)\n",`
356			`__FUNCTION__,`
357			`configure->vcc,`
358			`configure->vpp);`
359			`break;`
360			`}`
361			`break;`
362			`case 33: /* Vcc 3.3V */`
363			`switch(configure->vpp) {`
364			`case 0:`
365			`pcr \|= SET_VCC_VPP(1,0);`
366			`break;`
367			`case 12:`
368			`pcr \|= SET_VCC_VPP(1,2);`
369			`break;`
370			`case 33:`
371			`pcr \|= SET_VCC_VPP(1,1);`
372			`break;`
373			`case 50:`
374			`default:`
375			`pcr \|= SET_VCC_VPP(0,0);`
376			`printk("%s: bad Vcc/Vpp (%d:%d)\n",`
377			`__FUNCTION__,`
378			`configure->vcc,`
379			`configure->vpp);`
380			`break;`
381			`}`
382			`break;`
383			`default: /* what's this ? */`
384			`pcr \|= SET_VCC_VPP(0,0);`
385			`printk(KERN_ERR "%s: bad Vcc %d\n",`
386			`__FUNCTION__, configure->vcc);`
387			`break;`
388			`}`
389
390			`au_writew(pcr, PCMCIA_BOARD_REG);`
391			`au_sync_delay(300);`
392
393			`if (!configure->reset) {`
394			`pcr \|= PC_DRV_EN;`
395			`au_writew(pcr, PCMCIA_BOARD_REG);`
396			`au_sync_delay(100);`
397			`pcr \|= PC_DEASSERT_RST;`
398			`au_writew(pcr, PCMCIA_BOARD_REG);`
399			`au_sync_delay(100);`
400			`}`
401			`else {`
402			`pcr &= ~(PC_DEASSERT_RST \| PC_DRV_EN);`
403			`au_writew(pcr, PCMCIA_BOARD_REG);`
404			`au_sync_delay(100);`
405			`}`
406			`#endif`
407			`return 0;`
408			`}`
409
410
411			`struct pcmcia_low_level pb1x00_pcmcia_ops = {`
412			`pb1x00_pcmcia_init,`
413			`pb1x00_pcmcia_shutdown,`
414			`pb1x00_pcmcia_socket_state,`
415			`pb1x00_pcmcia_get_irq_info,`
416			`pb1x00_pcmcia_configure_socket`
417			`};`