Subversion Repositories or1k

/*

 * linux/include/asm-arm/arch-sa1100/hardware.h

 *

 * Copyright (C) 1998 Nicolas Pitre <nico@cam.org>

 *

 * This file contains the hardware definitions for SA1100 architecture

 *

 * 2000/05/23 John Dorsey <john+@cs.cmu.edu>

 *      Definitions for SA1111 added.

 */

#ifndef __ASM_ARCH_HARDWARE_H

#define __ASM_ARCH_HARDWARE_H

#include <linux/config.h>

#include <asm/mach-types.h>

/* Flushing areas */

#define FLUSH_BASE_PHYS         0xe0000000      /* SA1100 zero bank */

#define FLUSH_BASE              0xf5000000

#define FLUSH_BASE_MINICACHE    0xf5800000

#define UNCACHEABLE_ADDR        0xfa050000

/*

 * Those are statically mapped PCMCIA IO space for designs using it as a

 * generic IO bus, typically with ISA parts, hardwired IDE interfaces, etc.

 * The actual PCMCIA code is mapping required IO region at run time.

 */

#define PCMCIA_IO_0_BASE        0xf6000000

#define PCMCIA_IO_1_BASE        0xf7000000

/*

 * We requires absolute addresses i.e. (PCMCIA_IO_0_BASE + 0x3f8) for

 * in*()/out*() macros to be usable for all cases.

 */

#define PCIO_BASE               0

/*

 * SA1100 internal I/O mappings

 *

 * We have the following mapping:

 *      phys            virt

 *      80000000        f8000000

 *      90000000        fa000000

 *      a0000000        fc000000

 *      b0000000        fe000000

 */

#define VIO_BASE        0xf8000000      /* virtual start of IO space */

#define VIO_SHIFT       3               /* x = IO space shrink power */

#define PIO_START       0x80000000      /* physical start of IO space */

#define io_p2v( x )             \

   ( (((x)&0x00ffffff) | (((x)&0x30000000)>>VIO_SHIFT)) + VIO_BASE )

#define io_v2p( x )             \

   ( (((x)&0x00ffffff) | (((x)&(0x30000000>>VIO_SHIFT))<<VIO_SHIFT)) + PIO_START )

#ifndef __ASSEMBLY__

#include <asm/types.h>

#if 0

# define __REG(x)       (*((volatile u32 *)io_p2v(x)))

#else

/*

 * This __REG() version gives the same results as the one above,  except

 * that we are fooling gcc somehow so it generates far better and smaller

 * assembly code for access to contigous registers.  It's a shame that gcc

 * doesn't guess this by itself.

 */

typedef struct { volatile u32 offset[4096]; } __regbase;

# define __REGP(x)      ((__regbase *)((x)&~4095))->offset[((x)&4095)>>2]

# define __REG(x)       __REGP(io_p2v(x))

#endif

# define __PREG(x)      (io_v2p((u32)&(x)))

#else

# define __REG(x)       io_p2v(x)

# define __PREG(x)      io_v2p(x)

#endif

#include "SA-1100.h"

/*

 * SA1100 GPIO edge detection for IRQs:

 * IRQs are generated on Falling-Edge, Rising-Edge, or both.

 * This must be called *before* the corresponding IRQ is registered.

 * Use this instead of directly setting GRER/GFER.

 */

#define GPIO_NO_EDGES           0

#define GPIO_FALLING_EDGE       1

#define GPIO_RISING_EDGE        2

#define GPIO_BOTH_EDGES         3

#ifndef __ASSEMBLY__

extern void set_GPIO_IRQ_edge( int gpio_mask, int edge_mask );

#endif

/*

 * Implementation specifics.

 *

 *                      *** BIG FAT NOTE ***

 *

 * Any definitions in these files should be prefixed by an identifier -

 * eg, ASSABET_UCB1300_IRQ  This will allow us to eleminate these

 * ifdefs, and lots of other preprocessor gunk elsewhere.

 *

 * Also, please try to add your entry in alphabetical order.  The

 * initial ones below are the start of the alphabetical list.

 *

 * Do NOT add your ifdefs around your file.

 */

#include "badge4.h"

#include "frodo.h"

#include "h3600.h"

#include "system3.h"

#ifdef CONFIG_SA1100_PANGOLIN

#include "pangolin.h"

#endif

#ifdef CONFIG_SA1100_HUW_WEBPANEL

#include "huw_webpanel.h"

#endif

#ifdef CONFIG_SA1100_PFS168

#include "pfs168.h"

#endif

#ifdef CONFIG_SA1100_YOPY

#include "yopy.h"

#endif

#ifdef CONFIG_SA1100_FREEBIRD

#include "freebird.h"

#endif

#ifdef CONFIG_SA1100_CERF

#include "cerf.h"

#endif

#ifdef CONFIG_SA1100_EMPEG

#include "empeg.h"

#endif

#ifdef CONFIG_SA1100_ITSY

#include "itsy.h"

#endif

#if defined(CONFIG_SA1100_GRAPHICSCLIENT)

#include "graphicsclient.h"

#endif

#if defined(CONFIG_SA1100_OMNIMETER)

#include "omnimeter.h"

#endif

#if defined(CONFIG_SA1100_JORNADA720)

#include "jornada720.h"

#endif

#if defined(CONFIG_SA1100_PLEB)

#include "pleb.h"

#endif

#if defined(CONFIG_SA1100_LART)

#include "lart.h"

#endif

#ifdef CONFIG_SA1100_SIMPAD

#include "simpad.h"

#endif

#ifdef CONFIG_SA1100_SIMPUTER

#include "simputer.h"

#endif

#if defined(CONFIG_SA1100_GRAPHICSMASTER)

#include "graphicsmaster.h"

#endif

#if defined(CONFIG_SA1100_ADSAGC)

#include "adsagc.h"

#endif

#if defined(CONFIG_SA1100_ADSBITSY)

#include "adsbitsy.h"

#endif

#if defined(CONFIG_SA1100_ADSBITSYPLUS)

#include "adsbitsyplus.h"

#endif

#ifdef CONFIG_SA1101

/*

 * We have mapped the sa1101 depending on the value of SA1101_BASE.

 * It then appears from 0xf4000000.

 */

#define SA1101_p2v( x )         ((x) - SA1101_BASE + 0xf4000000)

#define SA1101_v2p( x )         ((x) - 0xf4000000  + SA1101_BASE)

#include "SA-1101.h"

#endif

#if defined(CONFIG_SA1100_OMNIMETER)

#include "omnimeter.h"

#endif

#if defined(CONFIG_SA1100_JORNADA720)

#include "jornada720.h"

#endif

#if defined(CONFIG_SA1100_FLEXANET)

#include "flexanet.h"

#endif

#endif  /* _ASM_ARCH_HARDWARE_H */