Subversion Repositories or1k

ROMFS - ROM FILE SYSTEM

This is a quite dumb, read only filesystem, mainly for initial ram

disks of installation disks.  It has grown up by the need of having

modules linked at boot time.  Using this filesystem, you get a very

similar feature, and even the possibility of a small kernel, with a

file system which doesn't take up useful memory from the router

functions in the basement of your office.

For comparison, both the older minix and xiafs (the latter is now

defunct) filesystems, compiled as module need more than 20000 bytes,

while romfs is less than a page, about 4000 bytes (assuming i586

code).  Under the same conditions, the msdos filesystem would need

about 30K (and does not support device nodes or symlinks), while the

nfs module with nfsroot is about 57K.  Furthermore, as a bit unfair

comparison, an actual rescue disk used up 3202 blocks with ext2, while

with romfs, it needed 3079 blocks.

To create such a file system, you'll need a user program named

genromfs.  It is available via anonymous ftp on sunsite.unc.edu and

its mirrors, in the /pub/Linux/system/recovery/ directory.

As the name suggests, romfs could be also used (space-efficiently) on

various read-only medias, like (E)EPROM disks if someone will have the

motivation.. :)

However, the main purpose of romfs is to have a very small kernel,

which has only this filesystem linked in, and then can load any module

later, with the current module utilities.  It can also be used to run

some program to decide if you need SCSI devices, and even IDE or

floppy drives can be loaded later if you use the "initrd" -- initial

ram disk -- feature of the kernel.  This would not be really news

flash, but with romfs, you can even spare off your ext2 or minix or

maybe even affs filesystem until you really know that you need it.

For example, a distribution boot disk can contain only the cd disk

drivers (and possibly the SCSI drivers), and the ISO filesystem

module.  The kernel can be small enough, since it doesn't have other

filesystems, like the quite large ext2fs module, which can then be

loaded off the CD at a later stage of the installation.  Another use

would be for a recovery disk, when you are reinstalling a workstation

from the network, and you will have all the tools/modules available

from a nearby server, so you don't want to carry two disks for this

purpose, just because it won't fit into ext2.

romfs operates on block devices as you can expect, and the underlying

structure is very simple.  Every accessible structure begins on 16

byte boundaries for fast access.  The minimum space a file will take

is 32 bytes (this is an empty file, with a less than 16 character

name).  The maximum overhead for any non-empty file is the header, and

the 16 byte padding for the name and the contents, also 16+14+15 = 45

bytes.  This is quite rare however, since most file names are longer

than 3 bytes, and shorter than 15 bytes.

The layout of the filesystem is the following:

offset      content

        +---+---+---+---+

        +---+---+---+---+       The ASCII representation of those bytes

  4     | 1 | f | s | - |  /    (i.e. "-rom1fs-")

        +---+---+---+---+

  8     |   full size   |       The number of accessible bytes in this fs.

        +---+---+---+---+

 12     |    checksum   |       The checksum of the FIRST 512 BYTES.

        +---+---+---+---+

 16     | volume name   |       The zero terminated name of the volume,

        :               :       padded to 16 byte boundary.

        +---+---+---+---+

 xx     |     file      |

        :    headers    :

Every multi byte value (32 bit words, I'll use the longwords term from

now on) must be in big endian order.

The first eight bytes identify the filesystem, even for the casual

inspector.  After that, in the 3rd longword, it contains the number of

bytes accessible from the start of this filesystem.  The 4th longword

is the checksum of the first 512 bytes (or the number of bytes

accessible, whichever is smallest).  The applied algorithm is the same

as in the AFFS filesystem, namely a simple sum of the longwords

(assuming bigendian quantities again).  For details, please consult

the source.  This algorithm was chosen because although it's not quite

reliable, it does not require any tables, and it is very simple.

The following bytes are now part of the file system; each file header

must begin on a 16 byte boundary.

offset      content

        +---+---+---+---+

        +---+---+---+---+         (zero if no more files)

  4     |   spec.info   |       Info for directories/hard links/devices

        +---+---+---+---+

  8     |     size      |       The size of this file in bytes

        +---+---+---+---+

 12     |   checksum    |       Covering the meta data, including the file

        +---+---+---+---+         name, and padding

 16     | file name     |       The zero terminated name of the file,

        :               :       padded to 16 byte boundary

        +---+---+---+---+

 xx     | file data     |

        :               :

Since the file headers begin always at a 16 byte boundary, the lowest

4 bits would be always zero in the next filehdr pointer.  These four

bits are used for the mode information.  Bits 0..2 specify the type of

the file; while bit 4 shows if the file is executable or not.  The

permissions are assumed to be world readable, if this bit is not set,

and world executable if it is; except the character and block devices,

they are never accessible for other than owner.  The owner of every

file is user and group 0, this should never be a problem for the

intended use.  The mapping of the 8 possible values to file types is

the following:

          mapping               spec.info means

 1      directory       first file's header

 2      regular file    unused, must be zero [MBZ]

 3      symbolic link   unused, MBZ (file data is the link content)

 4      block device    16/16 bits major/minor number

 5      char device                 - " -

 6      socket          unused, MBZ

 7      fifo            unused, MBZ

Note that hard links are specifically marked in this filesystem, but

they will behave as you can expect (i.e. share the inode number).

Note also that it is your responsibility to not create hard link

loops, and creating all the . and .. links for directories.  This is

normally done correctly by the genromfs program.  Please refrain from

using the executable bits for special purposes on the socket and fifo

special files, they may have other uses in the future.  Additionally,

please remember that only regular files, and symlinks are supposed to

have a nonzero size field; they contain the number of bytes available

directly after the (padded) file name.

Another thing to note is that romfs works on file headers and data

aligned to 16 byte boundaries, but most hardware devices and the block

device drivers are unable to cope with smaller than block-sized data.

To overcome this limitation, the whole size of the file system must be

padded to an 1024 byte boundary.

If you have any problems or suggestions concerning this file system,

please contact me.  However, think twice before wanting me to add

features and code, because the primary and most important advantage of

this file system is the small code.  On the other hand, don't be

alarmed, I'm not getting that much romfs related mail.  Now I can

understand why Avery wrote poems in the arcnet docs to get some more

feedback. :)

romfs has also a mailing list, and to date, it hasn't received any

traffic, so you are welcome to join it to discuss your ideas. :)

It's run by ezmlm, so you can subscribe to it by sending a message

to romfs-subscribe@shadow.banki.hu, the content is irrelevant.

Pending issues:

- Permissions and owner information are pretty essential features of a

Un*x like system, but romfs does not provide the full possibilities.

I have never found this limiting, but others might.

- The file system is read only, so it can be very small, but in case

one would want to write _anything_ to a file system, he still needs

a writable file system, thus negating the size advantages.  Possible

solutions: implement write access as a compile-time option, or a new,

similarly small writable filesystem for ram disks.

- Since the files are only required to have alignment on a 16 byte

boundary, it is currently possibly suboptimal to read or execute files

from the filesystem.  It might be resolved by reordering file data to

have most of it (i.e. except the start and the end) laying at "natural"

boundaries, thus it would be possible to directly map a big portion of

the file contents to the mm subsystem.

- Compression might be an useful feature, but memory is quite a

limiting factor in my eyes.

- Where it is used?

- Does it work on other architectures than intel and motorola?

Have fun,

Janos Farkas