| 1 |
1626 |
jcastillo |
This driver is for Compaq's SMART2 Intellegent Disk Array Controllers.
|
| 2 |
|
|
|
| 3 |
|
|
WARNING:
|
| 4 |
|
|
--------
|
| 5 |
|
|
|
| 6 |
|
|
This code is distributed without warranty. Use at your own risk.
|
| 7 |
|
|
|
| 8 |
|
|
Installing:
|
| 9 |
|
|
-----------
|
| 10 |
|
|
|
| 11 |
|
|
You need to build a new kernel to use this device, even if you want to
|
| 12 |
|
|
use a loadable module. This driver requires Leonard N. Zubkoff's excellent
|
| 13 |
|
|
patches to ll_rw_blk.c (to controll the number of scatter/gather elements
|
| 14 |
|
|
sent to lower disk drivers). Visit http://www.dandelion.com/Linux/DAC960.html
|
| 15 |
|
|
to get his patches.
|
| 16 |
|
|
|
| 17 |
|
|
Apply the patch to a 2.0.36 kernel after applying Leonard's patch:
|
| 18 |
|
|
|
| 19 |
|
|
# cd linux
|
| 20 |
|
|
# patch -p1
|
| 21 |
|
|
# patch -p1
|
| 22 |
|
|
|
| 23 |
|
|
Then build a new kernel and turn on Compaq SMART2 Disk Array support.
|
| 24 |
|
|
Create device nodes for the diskarray device:
|
| 25 |
|
|
|
| 26 |
|
|
# mkdev.ida [ctlrs]
|
| 27 |
|
|
|
| 28 |
|
|
Where ctlrs is the number of controllers you have (defaults to 1 if not
|
| 29 |
|
|
specified).
|
| 30 |
|
|
|
| 31 |
|
|
EISA Controllers:
|
| 32 |
|
|
-----------------
|
| 33 |
|
|
|
| 34 |
|
|
If you want to use an EISA controller you'll have to turn on EISA support
|
| 35 |
|
|
and supply some insmod/lilo paramaters. If the driver is compiled into the
|
| 36 |
|
|
kernel, must give it port/irq data at boot time. For example, if you had
|
| 37 |
|
|
two SMART-2/E controllers, in EISA slots 1 and 2, on irqs 15 and 5 respectively
|
| 38 |
|
|
you'd give it a boot argument like this:
|
| 39 |
|
|
|
| 40 |
|
|
smart2=0x1000,0xf,0x2000,0x5
|
| 41 |
|
|
|
| 42 |
|
|
If you were loading the driver as a module, you'd give load it like this:
|
| 43 |
|
|
|
| 44 |
|
|
insmod cpqarray.o eisa=0x1000,0xf,0x2000,0x5
|
| 45 |
|
|
|
| 46 |
|
|
You can use EISA and PCI adapters at the same time.
|
| 47 |
|
|
|
| 48 |
|
|
Booting:
|
| 49 |
|
|
--------
|
| 50 |
|
|
|
| 51 |
|
|
You'll need to use a modified lilo if you want to boot from a disk array.
|
| 52 |
|
|
Its simply a version of lilo with some code added to tell it how to
|
| 53 |
|
|
understand Compaq diskarray devices.
|
| 54 |
|
|
|
| 55 |
|
|
Device Naming:
|
| 56 |
|
|
--------------
|
| 57 |
|
|
|
| 58 |
|
|
You need some entries in /dev for the ida device. The mkdev.ida script
|
| 59 |
|
|
can make device nodes for you automatically. Currently the device setup
|
| 60 |
|
|
is as follows:
|
| 61 |
|
|
|
| 62 |
|
|
Major numbers:
|
| 63 |
|
|
72 ida0
|
| 64 |
|
|
73 ida1
|
| 65 |
|
|
74 ida2
|
| 66 |
|
|
etc...
|
| 67 |
|
|
|
| 68 |
|
|
Minor numbers:
|
| 69 |
|
|
b7 b6 b5 b4 b3 b2 b1 b0
|
| 70 |
|
|
|----+----| |----+----|
|
| 71 |
|
|
| |
|
| 72 |
|
|
| +-------- Partition ID (0=wholedev, 1-15 partition)
|
| 73 |
|
|
|
|
| 74 |
|
|
+-------------------- Logical Volume number
|
| 75 |
|
|
|
| 76 |
|
|
The suggested device naming scheme is:
|
| 77 |
|
|
/dev/ida/c0d0 Controller 0, disk 0, whole device
|
| 78 |
|
|
/dev/ida/c0d0p1 Controller 0, disk 0, partition 1
|
| 79 |
|
|
/dev/ida/c0d0p2 Controller 0, disk 0, partition 2
|
| 80 |
|
|
/dev/ida/c0d0p3 Controller 0, disk 0, partition 3
|
| 81 |
|
|
|
| 82 |
|
|
/dev/ida/c1d1 Controller 1, disk 1, whole device
|
| 83 |
|
|
/dev/ida/c1d1p1 Controller 1, disk 1, partition 1
|
| 84 |
|
|
/dev/ida/c1d1p2 Controller 1, disk 1, partition 2
|
| 85 |
|
|
/dev/ida/c1d1p3 Controller 1, disk 1, partition 3
|
