URL https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [char/] [mcfserial.c] - Blame information for rev 1765

Details | Compare with Previous | View Log

/*
 * mcfserial.c -- serial driver for ColdFire internal UARTS.
 *
 * Copyright (C) 1999 Greg Ungerer (gerg@moreton.com.au)
 *
 * Based on code from 68332serial.c which was:
 *
 * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
 * Copyright (C) 1998 TSHG
 */
 
#include <linux/errno.h>
#include <linux/signal.h>
#include <linux/sched.h>
#include <linux/timer.h>
#include <linux/interrupt.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/config.h>
#include <linux/major.h>
#include <linux/string.h>
#include <linux/fcntl.h>
#include <linux/mm.h>
#include <linux/kernel.h>
 
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/segment.h>
#include <asm/bitops.h>
#include <asm/delay.h>
#include <asm/coldfire.h>
#include <asm/mcfsim.h>
#include <asm/mcfuart.h>
#include <asm/nettel.h>
#include "mcfserial.h"
 
 
/*
 *      Default console port and baud rate...
 */
#ifndef CONSOLE_PORT
#define CONSOLE_PORT            0
#endif
#ifndef CONSOLE_BAUD_RATE
#define CONSOLE_BAUD_RATE       9600
#endif
 
int mcfrs_console_inited = 0;
int mcfrs_console_port = CONSOLE_PORT;
int mcfrs_console_baud = CONSOLE_BAUD_RATE;
 
 
DECLARE_TASK_QUEUE(mcf_tq_serial);
 
/*
 *      Driver data structures.
 */
struct tty_driver       mcfrs_serial_driver, mcfrs_callout_driver;
static int              mcfrs_serial_refcount;
 
/* serial subtype definitions */
#define SERIAL_TYPE_NORMAL      1
#define SERIAL_TYPE_CALLOUT     2
 
/* number of characters left in xmit buffer before we ask for more */
#define WAKEUP_CHARS 256
 
/* Debugging...
 */
#undef SERIAL_DEBUG_OPEN
#undef SERIAL_DEBUG_FLOW
 
#define _INLINE_ inline
 
#define IRQBASE 224
 
/*
 *      Configuration table, UARTs to look for at startup.
 */
static struct mcf_serial mcfrs_table[] = {
  { 0, (MCF_MBAR+MCFUART_BASE1), IRQBASE,   ASYNC_BOOT_AUTOCONF },  /* ttyS0 */
  { 0, (MCF_MBAR+MCFUART_BASE2), IRQBASE+1, ASYNC_BOOT_AUTOCONF },  /* ttyS1 */
};
 
 
#define NR_PORTS        (sizeof(mcfrs_table) / sizeof(struct mcf_serial))
 
static struct tty_struct        *mcfrs_serial_table[NR_PORTS];
static struct termios           *mcfrs_serial_termios[NR_PORTS];
static struct termios           *mcfrs_serial_termios_locked[NR_PORTS];
 
/*
 * This is used to figure out the divisor speeds and the timeouts.
 */
static int mcfrs_baud_table[] = {
        0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
        9600, 19200, 38400, 57600, 115200, 230400, 460800, 0
};
 
 
#ifndef MIN
#define MIN(a,b)        ((a) < (b) ? (a) : (b))
#endif
 
#ifdef CONFIG_MAGIC_SYSRQ
/*
 *      Magic system request keys. Used for debugging...
 */
extern int      magic_sysrq_key(int ch);
#endif
 
 
/*
 * tmp_buf is used as a temporary buffer by serial_write.  We need to
 * lock it in case the memcpy_fromfs blocks while swapping in a page,
 * and some other program tries to do a serial write at the same time.
 * Since the lock will only come under contention when the system is
 * swapping and available memory is low, it makes sense to share one
 * buffer across all the serial ports, since it significantly saves
 * memory if large numbers of serial ports are open.
 */
static unsigned char mcfrs_tmp_buf[4096]; /* This is cheating */
static struct semaphore mcfrs_tmp_buf_sem = MUTEX;
 
/*
 *      Forware declarations...
 */
static void     mcfrs_change_speed(struct mcf_serial *info);
 
 
static inline int serial_paranoia_check(struct mcf_serial *info,
                                        dev_t device, const char *routine)
{
#ifdef SERIAL_PARANOIA_CHECK
        static const char *badmagic =
                "Warning: bad magic number for serial struct (%d, %d) in %s\n";
        static const char *badinfo =
                "Warning: null mcf_serial for (%d, %d) in %s\n";
 
        if (!info) {
                printk(badinfo, MAJOR(device), MINOR(device), routine);
                return 1;
        }
        if (info->magic != SERIAL_MAGIC) {
                printk(badmagic, MAJOR(device), MINOR(device), routine);
                return 1;
        }
#endif
        return 0;
}
 
/*
 *      Sets or clears DTR and RTS on the requested line.
 */
static void mcfrs_setsignals(struct mcf_serial *info, int dtr, int rts)
{
        volatile unsigned char  *uartp;
        unsigned long           flags;
 
#if 0
        printk("%s(%d): mcfrs_setsignals(info=%x,dtr=%d,rts=%d)\n",
                __FILE__, __LINE__, info, dtr, rts);
#endif
 
        save_flags(flags); cli();
        if (dtr >= 0) {
#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
                if (dtr) {
                        info->sigs |= TIOCM_DTR;
                        ppdata &= ~(info->line ? NETtel_DTR1 : NETtel_DTR0);
                } else {
                        info->sigs &= ~TIOCM_DTR;
                        ppdata |= (info->line ? NETtel_DTR1 : NETtel_DTR0);
                }
                *((volatile unsigned short *) (MCF_MBAR+MCFSIM_PADAT)) = ppdata;
#endif
        }
        if (rts >= 0) {
                uartp = (volatile unsigned char *) info->addr;
                if (rts) {
                        info->sigs |= TIOCM_RTS;
                        uartp[MCFUART_UOP1] = MCFUART_UOP_RTS;
                } else {
                        info->sigs &= ~TIOCM_RTS;
                        uartp[MCFUART_UOP0] = MCFUART_UOP_RTS;
                }
        }
        restore_flags(flags);
        return;
}
 
/*
 *      Gets values of serial signals.
 */
static int mcfrs_getsignals(struct mcf_serial *info)
{
        volatile unsigned char  *uartp;
        unsigned long           flags;
        int                     sigs;
#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
        unsigned short          ppdata;
#endif
 
#if 0
        printk("%s(%d): mcfrs_getsignals(info=%x)\n", __FILE__, __LINE__);
#endif
 
        save_flags(flags); cli();
        uartp = (volatile unsigned char *) info->addr;
        sigs = (uartp[MCFUART_UIPR] & MCFUART_UIPR_CTS) ? 0 : TIOCM_CTS;
        sigs |= (info->sigs & TIOCM_RTS);
 
#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
        ppdata = *((volatile unsigned short *) (MCF_MBAR+MCFSIM_PADAT));
        if (info->line == 0) {
                sigs |= (ppdata & NETtel_DCD0) ? 0 : TIOCM_CD;
                sigs |= (ppdata & NETtel_DTR0) ? 0 : TIOCM_DTR;
        } else if (info->line == 1) {
                sigs |= (ppdata & NETtel_DCD1) ? 0 : TIOCM_CD;
                sigs |= (ppdata & NETtel_DTR1) ? 0 : TIOCM_DTR;
        }
#endif
 
        restore_flags(flags);
        return(sigs);
}
 
/*
 * ------------------------------------------------------------
 * mcfrs_stop() and mcfrs_start()
 *
 * This routines are called before setting or resetting tty->stopped.
 * They enable or disable transmitter interrupts, as necessary.
 * ------------------------------------------------------------
 */
static void mcfrs_stop(struct tty_struct *tty)
{
        volatile unsigned char  *uartp;
        struct mcf_serial       *info = (struct mcf_serial *)tty->driver_data;
        unsigned long           flags;
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_stop"))
                return;
 
        save_flags(flags); cli();
        uartp = (volatile unsigned char *) info->addr;
        info->imr &= ~MCFUART_UIR_TXREADY;
        uartp[MCFUART_UIMR] = info->imr;
        restore_flags(flags);
}
 
static void mcfrs_start(struct tty_struct *tty)
{
        volatile unsigned char  *uartp;
        struct mcf_serial       *info = (struct mcf_serial *)tty->driver_data;
        unsigned long           flags;
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_start"))
                return;
 
        save_flags(flags); cli();
        if (info->xmit_cnt && info->xmit_buf) {
                uartp = (volatile unsigned char *) info->addr;
                info->imr |= MCFUART_UIR_TXREADY;
                uartp[MCFUART_UIMR] = info->imr;
        }
        restore_flags(flags);
}
 
/*
 * ----------------------------------------------------------------------
 *
 * Here starts the interrupt handling routines.  All of the following
 * subroutines are declared as inline and are folded into
 * mcfrs_interrupt().  They were separated out for readability's sake.
 *
 * Note: mcfrs_interrupt() is a "fast" interrupt, which means that it
 * runs with interrupts turned off.  People who may want to modify
 * mcfrs_interrupt() should try to keep the interrupt handler as fast as
 * possible.  After you are done making modifications, it is not a bad
 * idea to do:
 *
 * gcc -S -DKERNEL -Wall -Wstrict-prototypes -O6 -fomit-frame-pointer serial.c
 *
 * and look at the resulting assemble code in serial.s.
 *
 *                              - Ted Ts'o (tytso@mit.edu), 7-Mar-93
 * -----------------------------------------------------------------------
 */
 
/*
 * This routine is used by the interrupt handler to schedule
 * processing in the software interrupt portion of the driver.
 */
static _INLINE_ void mcfrs_sched_event(struct mcf_serial *info, int event)
{
        info->event |= 1 << event;
        queue_task_irq_off(&info->tqueue, &mcf_tq_serial);
        mark_bh(SERIAL_BH);
}
 
static _INLINE_ void receive_chars(struct mcf_serial *info, struct pt_regs *regs, unsigned short rx)
{
        volatile unsigned char  *uartp;
        struct tty_struct       *tty = info->tty;
        unsigned char           status, ch;
 
        if (!tty)
                return;
 
#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
        setled(info->line ? NETtel_LEDRX2 : NETtel_LEDRX1);
#endif
 
        uartp = (volatile unsigned char *) info->addr;
 
        while ((status = uartp[MCFUART_USR]) & MCFUART_USR_RXREADY) {
 
                if (tty->flip.count >= TTY_FLIPBUF_SIZE)
                        break;
 
                ch = uartp[MCFUART_URB];
                info->stats.rx++;
 
#ifdef CONFIG_MAGIC_SYSRQ
                if (mcfrs_console_inited && (info->line == mcfrs_console_port)) {
                        if (magic_sysrq_key(ch))
                                continue;
                }
#endif
 
                tty->flip.count++;
                if (status & MCFUART_USR_RXERR)
                        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETERR;
                if (status & MCFUART_USR_RXBREAK) {
                        info->stats.rxbreak++;
                        *tty->flip.flag_buf_ptr++ = TTY_BREAK;
                } else if (status & MCFUART_USR_RXPARITY) {
                        info->stats.rxparity++;
                        *tty->flip.flag_buf_ptr++ = TTY_PARITY;
                } else if (status & MCFUART_USR_RXOVERRUN) {
                        info->stats.rxoverrun++;
                        *tty->flip.flag_buf_ptr++ = TTY_OVERRUN;
                } else if (status & MCFUART_USR_RXFRAMING) {
                        info->stats.rxframing++;
                        *tty->flip.flag_buf_ptr++ = TTY_FRAME;
                } else {
                        *tty->flip.flag_buf_ptr++ = 0;
                }
                *tty->flip.char_buf_ptr++ = ch;
        }
 
        queue_task_irq_off(&tty->flip.tqueue, &tq_timer);
        return;
}
 
static _INLINE_ void transmit_chars(struct mcf_serial *info)
{
        volatile unsigned char  *uartp;
 
#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
        setled(info->line ? NETtel_LEDTX2 : NETtel_LEDTX1);
#endif
        uartp = (volatile unsigned char *) info->addr;
 
        if (info->x_char) {
                /* Send special char - probably flow control */
                uartp[MCFUART_UTB] = info->x_char;
#if 0
                printk("%s(%d): sending flow=%x\n", __FILE__, __LINE__, info->x_char);
#endif
                info->x_char = 0;
                info->stats.tx++;
        }
 
        if ((info->xmit_cnt <= 0) || info->tty->stopped) {
                info->imr &= ~MCFUART_UIR_TXREADY;
                uartp[MCFUART_UIMR] = info->imr;
                return;
        }
 
        while (uartp[MCFUART_USR] & MCFUART_USR_TXREADY) {
                uartp[MCFUART_UTB] = info->xmit_buf[info->xmit_tail++];
                info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
                info->stats.tx++;
                if (--info->xmit_cnt <= 0)
                        break;
        }
 
        if (info->xmit_cnt < WAKEUP_CHARS)
                mcfrs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
        return;
}
 
/*
 * This is the serial driver's generic interrupt routine
 */
void mcfrs_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
        struct mcf_serial       *info;
        unsigned char           isr;
 
        info = &mcfrs_table[(irq - IRQBASE)];
        isr = (((volatile unsigned char *)info->addr)[MCFUART_UISR]) & info->imr;
 
        if (isr & MCFUART_UIR_RXREADY)
                receive_chars(info, regs, isr);
        if (isr & MCFUART_UIR_TXREADY)
                transmit_chars(info);
#if 0
        if (isr & MCFUART_UIR_DELTABREAK) {
                printk("%s(%d): delta break!\n", __FILE__, __LINE__);
                receive_chars(info, regs, isr);
        }
#endif
 
        return;
}
 
/*
 * -------------------------------------------------------------------
 * Here ends the serial interrupt routines.
 * -------------------------------------------------------------------
 */
 
/*
 * This routine is used to handle the "bottom half" processing for the
 * serial driver, known also the "software interrupt" processing.
 * This processing is done at the kernel interrupt level, after the
 * mcfrs_interrupt() has returned, BUT WITH INTERRUPTS TURNED ON.  This
 * is where time-consuming activities which can not be done in the
 * interrupt driver proper are done; the interrupt driver schedules
 * them using mcfrs_sched_event(), and they get done here.
 */
static void do_serial_bh(void)
{
        run_task_queue(&mcf_tq_serial);
}
 
static void do_softint(void *private_)
{
        struct mcf_serial       *info = (struct mcf_serial *) private_;
        struct tty_struct       *tty;
 
        tty = info->tty;
        if (!tty)
                return;
 
        if (clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event)) {
                if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) &&
                    tty->ldisc.write_wakeup)
                        (tty->ldisc.write_wakeup)(tty);
                wake_up_interruptible(&tty->write_wait);
        }
}
 
 
/*
 *      Change of state on a DCD line.
 */
void mcfrs_modem_change(struct mcf_serial *info, int dcd)
{
        if (info->count == 0)
                return;
 
        if (info->flags & ASYNC_CHECK_CD) {
                if (dcd) {
                        wake_up_interruptible(&info->open_wait);
                } else if (!((info->flags & ASYNC_CALLOUT_ACTIVE) &&
                    (info->flags & ASYNC_CALLOUT_NOHUP))) {
                        queue_task_irq_off(&info->tqueue_hangup, &tq_scheduler);
                }
        }
}
 
 
#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
 
unsigned short  mcfrs_ppstatus;
 
/*
 * This subroutine is called when the RS_TIMER goes off. It is used
 * to monitor the state of the DCD lines - since they have no edge
 * sensors and interrupt generators.
 */
static void mcfrs_timer(void)
{
        unsigned short  ppstatus, dcdval;
        int             i;
 
        ppstatus = *((volatile unsigned short *) (MCF_MBAR + MCFSIM_PADAT)) &
                (NETtel_DCD0 | NETtel_DCD1);
 
        if (ppstatus != mcfrs_ppstatus) {
                for (i = 0; (i < 2); i++) {
                        dcdval = (i ? NETtel_DCD1 : NETtel_DCD0);
                        if ((ppstatus & dcdval) != (mcfrs_ppstatus & dcdval)) {
                                mcfrs_modem_change(&mcfrs_table[i],
                                        ((ppstatus & dcdval) ? 0 : 1));
                        }
                }
        }
        mcfrs_ppstatus = ppstatus;
 
        /* Re-arm timer */
        timer_table[RS_TIMER].expires = jiffies + HZ/25;
        timer_active |= 1 << RS_TIMER;
 
        /* Re-set the serial activity LEDs */
        unsetled((NETtel_LEDRX1|NETtel_LEDRX2|NETtel_LEDTX1|NETtel_LEDTX2));
}
 
#endif  /* CONFIG_NETtel */
 
 
/*
 * This routine is called from the scheduler tqueue when the interrupt
 * routine has signalled that a hangup has occurred.  The path of
 * hangup processing is:
 *
 *      serial interrupt routine -> (scheduler tqueue) ->
 *      do_serial_hangup() -> tty->hangup() -> mcfrs_hangup()
 *
 */
static void do_serial_hangup(void *private_)
{
        struct mcf_serial       *info = (struct mcf_serial *) private_;
        struct tty_struct       *tty;
 
        tty = info->tty;
        if (!tty)
                return;
 
        tty_hangup(tty);
}
 
static int startup(struct mcf_serial * info)
{
        volatile unsigned char  *uartp;
        unsigned long           flags;
 
        if (info->flags & ASYNC_INITIALIZED)
                return 0;
 
        if (!info->xmit_buf) {
                info->xmit_buf = (unsigned char *) get_free_page(GFP_KERNEL);
                if (!info->xmit_buf)
                        return -ENOMEM;
        }
 
        save_flags(flags); cli();
 
#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
        /*
         * Set up poll timer. It is used to check DCD status.
         */
        if ((timer_active & (1 << RS_TIMER)) == 0) {
                timer_table[RS_TIMER].expires = jiffies + HZ/25;
                timer_active |= 1 << RS_TIMER;
        }
#endif
 
#ifdef SERIAL_DEBUG_OPEN
        printk("starting up ttyS%d (irq %d)...\n", info->line, info->irq);
#endif
 
        /*
         *      Reset UART, get it into known state...
         */
        uartp = (volatile unsigned char *) info->addr;
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX;  /* reset RX */
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX;  /* reset TX */
        mcfrs_setsignals(info, 1, 1);
 
        if (info->tty)
                clear_bit(TTY_IO_ERROR, &info->tty->flags);
        info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
 
        /*
         * and set the speed of the serial port
         */
        mcfrs_change_speed(info);
 
        /*
         * Lastly enable the UART transmitter and receiver, and
         * interrupt enables.
         */
        info->imr = MCFUART_UIR_RXREADY;
        uartp[MCFUART_UCR] = MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE;
        uartp[MCFUART_UIMR] = info->imr;
 
        info->flags |= ASYNC_INITIALIZED;
        restore_flags(flags);
        return 0;
}
 
/*
 * This routine will shutdown a serial port; interrupts are disabled, and
 * DTR is dropped if the hangup on close termio flag is on.
 */
static void shutdown(struct mcf_serial * info)
{
        volatile unsigned char  *uartp;
        unsigned long           flags;
 
        if (!(info->flags & ASYNC_INITIALIZED))
                return;
 
#ifdef SERIAL_DEBUG_OPEN
        printk("Shutting down serial port %d (irq %d)....\n", info->line,
               info->irq);
#endif
 
        save_flags(flags); cli(); /* Disable interrupts */
 
        uartp = (volatile unsigned char *) info->addr;
        uartp[MCFUART_UIMR] = 0;  /* mask all interrupts */
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX;  /* reset RX */
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX;  /* reset TX */
 
        if (!info->tty || (info->tty->termios->c_cflag & HUPCL))
                mcfrs_setsignals(info, 0, 0);
 
        if (info->xmit_buf) {
                free_page((unsigned long) info->xmit_buf);
                info->xmit_buf = 0;
        }
 
        if (info->tty)
                set_bit(TTY_IO_ERROR, &info->tty->flags);
 
        info->flags &= ~ASYNC_INITIALIZED;
        restore_flags(flags);
}
 
 
/*
 * This routine is called to set the UART divisor registers to match
 * the specified baud rate for a serial port.
 */
static void mcfrs_change_speed(struct mcf_serial *info)
{
        volatile unsigned char  *uartp;
        unsigned int            baudclk, cflag;
        unsigned long           flags;
        unsigned char           mr1, mr2;
        int                     i;
 
        if (!info->tty || !info->tty->termios)
                return;
        cflag = info->tty->termios->c_cflag;
        if (info->addr == 0)
                return;
 
#if 0
        printk("%s(%d): mcfrs_change_speed()\n", __FILE__, __LINE__);
#endif
 
        i = cflag & CBAUD;
        if (i & CBAUDEX) {
                i &= ~CBAUDEX;
                if (i < 1 || i > 4)
                        info->tty->termios->c_cflag &= ~CBAUDEX;
                else
                        i += 15;
        }
        if (i == 0) {
                mcfrs_setsignals(info, 0, -1);
                return;
        }
        baudclk = ((MCF_CLK / 32) / mcfrs_baud_table[i]);
        info->baud = mcfrs_baud_table[i];
 
        mr1 = MCFUART_MR1_RXIRQRDY | MCFUART_MR1_RXERRCHAR;
        mr2 = 0;
 
        switch (cflag & CSIZE) {
        case CS5:       mr1 |= MCFUART_MR1_CS5; break;
        case CS6:       mr1 |= MCFUART_MR1_CS6; break;
        case CS7:       mr1 |= MCFUART_MR1_CS7; break;
        case CS8:
        default:        mr1 |= MCFUART_MR1_CS8; break;
        }
 
        if (cflag & PARENB) {
                if (cflag & PARODD)
                        mr1 |= MCFUART_MR1_PARITYODD;
                else
                        mr1 |= MCFUART_MR1_PARITYEVEN;
        } else {
                mr1 |= MCFUART_MR1_PARITYNONE;
        }
 
        if (cflag & CSTOPB)
                mr2 |= MCFUART_MR2_STOP2;
        else
                mr2 |= MCFUART_MR2_STOP1;
 
        if (cflag & CRTSCTS) {
                mr1 |= MCFUART_MR1_RXRTS;
                mr2 |= MCFUART_MR2_TXCTS;
        }
 
        if (cflag & CLOCAL)
                info->flags &= ~ASYNC_CHECK_CD;
        else
                info->flags |= ASYNC_CHECK_CD;
 
        uartp = (volatile unsigned char *) info->addr;
 
        save_flags(flags); cli();
#if 0
        printk("%s(%d): mr1=%x mr2=%x baudclk=%x\n", __FILE__, __LINE__,
                mr1, mr2, baudclk);
#endif
        /*
          Note: pg 12-16 of MCF5206e User's Manual states that a
          software reset should be performed prior to changing
          UMR1,2, UCSR, UACR, bit 7
        */
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX;    /* reset RX */
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX;    /* reset TX */
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETMRPTR; /* reset MR pointer */
        uartp[MCFUART_UMR] = mr1;
        uartp[MCFUART_UMR] = mr2;
        uartp[MCFUART_UBG1] = (baudclk & 0xff00) >> 8;  /* set msb byte */
        uartp[MCFUART_UBG2] = (baudclk & 0xff);         /* set lsb byte */
        uartp[MCFUART_UCSR] = MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER;
        uartp[MCFUART_UCR] = MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE;
        mcfrs_setsignals(info, 1, -1);
        restore_flags(flags);
        return;
}
 
static void mcfrs_flush_chars(struct tty_struct *tty)
{
        volatile unsigned char  *uartp;
        struct mcf_serial       *info = (struct mcf_serial *)tty->driver_data;
        unsigned long           flags;
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_flush_chars"))
                return;
 
        if (info->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped ||
            !info->xmit_buf)
                return;
 
        /* Enable transmitter */
        save_flags(flags); cli();
        uartp = (volatile unsigned char *) info->addr;
        info->imr |= MCFUART_UIR_TXREADY;
        uartp[MCFUART_UIMR] = info->imr;
        restore_flags(flags);
}
 
static int mcfrs_write(struct tty_struct * tty, int from_user,
                    const unsigned char *buf, int count)
{
        volatile unsigned char  *uartp;
        struct mcf_serial       *info = (struct mcf_serial *)tty->driver_data;
        unsigned long           flags;
        int                     c, total = 0;
 
#if 0
        printk("%s(%d): mcfrs_write(tty=%x,from_user=%d,buf=%x,count=%d)\n",
                __FILE__, __LINE__, tty, from_user, buf, count);
#endif
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_write"))
                return 0;
 
        if (!tty || !info->xmit_buf)
                return 0;
 
        save_flags(flags);
        while (1) {
                cli();
                c = MIN(count, MIN(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
                                   SERIAL_XMIT_SIZE - info->xmit_head));
 
                if (c <= 0) {
                        restore_flags(flags);
                        break;
                }
 
                if (from_user) {
                        down(&mcfrs_tmp_buf_sem);
                        memcpy_fromfs(mcfrs_tmp_buf, buf, c);
                        restore_flags(flags);
                        cli();
                        c = MIN(c, MIN(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
                                       SERIAL_XMIT_SIZE - info->xmit_head));
                        memcpy(info->xmit_buf + info->xmit_head, mcfrs_tmp_buf, c);
                        up(&mcfrs_tmp_buf_sem);
                } else
                        memcpy(info->xmit_buf + info->xmit_head, buf, c);
 
                info->xmit_head = (info->xmit_head + c) & (SERIAL_XMIT_SIZE-1);
                info->xmit_cnt += c;
                restore_flags(flags);
 
                buf += c;
                count -= c;
                total += c;
        }
 
        cli();
        uartp = (volatile unsigned char *) info->addr;
        info->imr |= MCFUART_UIR_TXREADY;
        uartp[MCFUART_UIMR] = info->imr;
        restore_flags(flags);
 
        return total;
}
 
static int mcfrs_write_room(struct tty_struct *tty)
{
        struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
        int     ret;
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_write_room"))
                return 0;
        ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
        if (ret < 0)
                ret = 0;
        return ret;
}
 
static int mcfrs_chars_in_buffer(struct tty_struct *tty)
{
        struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_chars_in_buffer"))
                return 0;
        return info->xmit_cnt;
}
 
static void mcfrs_flush_buffer(struct tty_struct *tty)
{
        struct mcf_serial       *info = (struct mcf_serial *)tty->driver_data;
        unsigned long           flags;
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_flush_buffer"))
                return;
 
        save_flags(flags); cli();
        info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
        restore_flags(flags);
 
        wake_up_interruptible(&tty->write_wait);
        if ((tty->flags & (1 << TTY_DO_WRITE_WAKEUP)) &&
            tty->ldisc.write_wakeup)
                (tty->ldisc.write_wakeup)(tty);
}
 
/*
 * ------------------------------------------------------------
 * mcfrs_throttle()
 *
 * This routine is called by the upper-layer tty layer to signal that
 * incoming characters should be throttled.
 * ------------------------------------------------------------
 */
static void mcfrs_throttle(struct tty_struct * tty)
{
        struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
#ifdef SERIAL_DEBUG_THROTTLE
        char    buf[64];
 
        printk("throttle %s: %d....\n", _tty_name(tty, buf),
               tty->ldisc.chars_in_buffer(tty));
#endif
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_throttle"))
                return;
 
        if (I_IXOFF(tty))
                info->x_char = STOP_CHAR(tty);
 
        /* Turn off RTS line (do this atomic) */
}
 
static void mcfrs_unthrottle(struct tty_struct * tty)
{
        struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
#ifdef SERIAL_DEBUG_THROTTLE
        char    buf[64];
 
        printk("unthrottle %s: %d....\n", _tty_name(tty, buf),
               tty->ldisc.chars_in_buffer(tty));
#endif
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_unthrottle"))
                return;
 
        if (I_IXOFF(tty)) {
                if (info->x_char)
                        info->x_char = 0;
                else
                        info->x_char = START_CHAR(tty);
        }
 
        /* Assert RTS line (do this atomic) */
}
 
/*
 * ------------------------------------------------------------
 * mcfrs_ioctl() and friends
 * ------------------------------------------------------------
 */
 
static int get_serial_info(struct mcf_serial * info,
                           struct serial_struct * retinfo)
{
        struct serial_struct tmp;
 
        if (!retinfo)
                return -EFAULT;
        memset(&tmp, 0, sizeof(tmp));
        tmp.type = info->type;
        tmp.line = info->line;
        tmp.port = info->addr;
        tmp.irq = info->irq;
        tmp.flags = info->flags;
        tmp.baud_base = info->baud_base;
        tmp.close_delay = info->close_delay;
        tmp.closing_wait = info->closing_wait;
        tmp.custom_divisor = info->custom_divisor;
        memcpy_tofs(retinfo,&tmp,sizeof(*retinfo));
        return 0;
}
 
static int set_serial_info(struct mcf_serial * info,
                           struct serial_struct * new_info)
{
        struct serial_struct new_serial;
        struct mcf_serial old_info;
        int                     retval = 0;
 
        if (!new_info)
                return -EFAULT;
        memcpy_fromfs(&new_serial,new_info,sizeof(new_serial));
        old_info = *info;
 
        if (!suser()) {
                if ((new_serial.baud_base != info->baud_base) ||
                    (new_serial.type != info->type) ||
                    (new_serial.close_delay != info->close_delay) ||
                    ((new_serial.flags & ~ASYNC_USR_MASK) !=
                     (info->flags & ~ASYNC_USR_MASK)))
                        return -EPERM;
                info->flags = ((info->flags & ~ASYNC_USR_MASK) |
                               (new_serial.flags & ASYNC_USR_MASK));
                info->custom_divisor = new_serial.custom_divisor;
                goto check_and_exit;
        }
 
        if (info->count > 1)
                return -EBUSY;
 
        /*
         * OK, past this point, all the error checking has been done.
         * At this point, we start making changes.....
         */
 
        info->baud_base = new_serial.baud_base;
        info->flags = ((info->flags & ~ASYNC_FLAGS) |
                        (new_serial.flags & ASYNC_FLAGS));
        info->type = new_serial.type;
        info->close_delay = new_serial.close_delay;
        info->closing_wait = new_serial.closing_wait;
 
check_and_exit:
        retval = startup(info);
        return retval;
}
 
/*
 * get_lsr_info - get line status register info
 *
 * Purpose: Let user call ioctl() to get info when the UART physically
 *          is emptied.  On bus types like RS485, the transmitter must
 *          release the bus after transmitting. This must be done when
 *          the transmit shift register is empty, not be done when the
 *          transmit holding register is empty.  This functionality
 *          allows an RS485 driver to be written in user space.
 */
static int get_lsr_info(struct mcf_serial * info, unsigned int *value)
{
        volatile unsigned char  *uartp;
        unsigned long           flags;
        unsigned char           status;
 
        save_flags(flags); cli();
        uartp = (volatile unsigned char *) info->addr;
        status = (uartp[MCFUART_USR] & MCFUART_USR_TXEMPTY) ? TIOCSER_TEMT : 0;
        restore_flags(flags);
 
        put_user(status,value);
        return 0;
}
 
/*
 * This routine sends a break character out the serial port.
 */
static void send_break( struct mcf_serial * info, int duration)
{
        volatile unsigned char  *uartp;
        unsigned long           flags;
 
        if (!info->addr)
                return;
        current->state = TASK_INTERRUPTIBLE;
        current->timeout = jiffies + duration;
        uartp = (volatile unsigned char *) info->addr;
 
        save_flags(flags); cli();
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDBREAKSTART;
        schedule();
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDBREAKSTOP;
        restore_flags(flags);
}
 
static int mcfrs_ioctl(struct tty_struct *tty, struct file * file,
                    unsigned int cmd, unsigned long arg)
{
        int error;
        struct mcf_serial * info = (struct mcf_serial *)tty->driver_data;
        int retval;
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_ioctl"))
                return -ENODEV;
 
        if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
            (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD)  &&
            (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
                if (tty->flags & (1 << TTY_IO_ERROR))
                    return -EIO;
        }
 
        switch (cmd) {
                case TCSBRK:    /* SVID version: non-zero arg --> no break */
                        retval = tty_check_change(tty);
                        if (retval)
                                return retval;
                        tty_wait_until_sent(tty, 0);
                        if (!arg)
                                send_break(info, HZ/4); /* 1/4 second */
                        return 0;
                case TCSBRKP:   /* support for POSIX tcsendbreak() */
                        retval = tty_check_change(tty);
                        if (retval)
                                return retval;
                        tty_wait_until_sent(tty, 0);
                        send_break(info, arg ? arg*(HZ/10) : HZ/4);
                        return 0;
                case TIOCGSOFTCAR:
                        error = verify_area(VERIFY_WRITE, (void *) arg,sizeof(long));
                        if (error)
                                return error;
                        put_fs_long(C_CLOCAL(tty) ? 1 : 0,
                                    (unsigned long *) arg);
                        return 0;
                case TIOCSSOFTCAR:
                        arg = get_fs_long((unsigned long *) arg);
                        tty->termios->c_cflag =
                                ((tty->termios->c_cflag & ~CLOCAL) |
                                 (arg ? CLOCAL : 0));
                        return 0;
                case TIOCGSERIAL:
                        error = verify_area(VERIFY_WRITE, (void *) arg,
                                                sizeof(struct serial_struct));
                        if (error)
                                return error;
                        return get_serial_info(info,
                                               (struct serial_struct *) arg);
                case TIOCSSERIAL:
                        return set_serial_info(info,
                                               (struct serial_struct *) arg);
                case TIOCSERGETLSR: /* Get line status register */
                        error = verify_area(VERIFY_WRITE, (void *) arg,
                                sizeof(unsigned int));
                        if (error)
                                return error;
                        else
                            return get_lsr_info(info, (unsigned int *) arg);
 
                case TIOCSERGSTRUCT:
                        error = verify_area(VERIFY_WRITE, (void *) arg,
                                                sizeof(struct mcf_serial));
                        if (error)
                                return error;
                        memcpy_tofs((struct mcf_serial *) arg,
                                    info, sizeof(struct mcf_serial));
                        return 0;
 
                default:
                        return -ENOIOCTLCMD;
                }
        return 0;
}
 
static void mcfrs_set_termios(struct tty_struct *tty, struct termios *old_termios)
{
        struct mcf_serial *info = (struct mcf_serial *)tty->driver_data;
 
        if (tty->termios->c_cflag == old_termios->c_cflag)
                return;
 
        mcfrs_change_speed(info);
 
        if ((old_termios->c_cflag & CRTSCTS) &&
            !(tty->termios->c_cflag & CRTSCTS)) {
                tty->hw_stopped = 0;
                mcfrs_setsignals(info, -1, 1);
                mcfrs_start(tty);
        }
}
 
/*
 * ------------------------------------------------------------
 * mcfrs_close()
 *
 * This routine is called when the serial port gets closed.  First, we
 * wait for the last remaining data to be sent.  Then, we unlink its
 * S structure from the interrupt chain if necessary, and we free
 * that IRQ if nothing is left in the chain.
 * ------------------------------------------------------------
 */
static void mcfrs_close(struct tty_struct *tty, struct file * filp)
{
        volatile unsigned char  *uartp;
        struct mcf_serial       *info = (struct mcf_serial *)tty->driver_data;
        unsigned long           flags;
 
        if (!info || serial_paranoia_check(info, tty->device, "mcfrs_close"))
                return;
 
        save_flags(flags); cli();
 
        if (tty_hung_up_p(filp)) {
                restore_flags(flags);
                return;
        }
 
#ifdef SERIAL_DEBUG_OPEN
        printk("mcfrs_close ttyS%d, count = %d\n", info->line, info->count);
#endif
        if ((tty->count == 1) && (info->count != 1)) {
                /*
                 * Uh, oh.  tty->count is 1, which means that the tty
                 * structure will be freed.  Info->count should always
                 * be one in these conditions.  If it's greater than
                 * one, we've got real problems, since it means the
                 * serial port won't be shutdown.
                 */
                printk("mcfrs_close: bad serial port count; tty->count is 1, "
                       "info->count is %d\n", info->count);
                info->count = 1;
        }
        if (--info->count < 0) {
                printk("mcfrs_close: bad serial port count for ttyS%d: %d\n",
                       info->line, info->count);
                info->count = 0;
        }
        if (info->count) {
                restore_flags(flags);
                return;
        }
        info->flags |= ASYNC_CLOSING;
 
        /*
         * Save the termios structure, since this port may have
         * separate termios for callout and dialin.
         */
        if (info->flags & ASYNC_NORMAL_ACTIVE)
                info->normal_termios = *tty->termios;
        if (info->flags & ASYNC_CALLOUT_ACTIVE)
                info->callout_termios = *tty->termios;
 
        /*
         * Now we wait for the transmit buffer to clear; and we notify
         * the line discipline to only process XON/XOFF characters.
         */
        tty->closing = 1;
        if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE)
                tty_wait_until_sent(tty, info->closing_wait);
 
        /*
         * At this point we stop accepting input.  To do this, we
         * disable the receive line status interrupts, and tell the
         * interrupt driver to stop checking the data ready bit in the
         * line status register.
         */
        info->imr &= ~MCFUART_UIR_RXREADY;
        uartp = (volatile unsigned char *) info->addr;
        uartp[MCFUART_UIMR] = info->imr;
 
        shutdown(info);
        if (tty->driver.flush_buffer)
                tty->driver.flush_buffer(tty);
        if (tty->ldisc.flush_buffer)
                tty->ldisc.flush_buffer(tty);
        tty->closing = 0;
        info->event = 0;
        info->tty = 0;
        if (tty->ldisc.num != ldiscs[N_TTY].num) {
                if (tty->ldisc.close)
                        (tty->ldisc.close)(tty);
                tty->ldisc = ldiscs[N_TTY];
                tty->termios->c_line = N_TTY;
                if (tty->ldisc.open)
                        (tty->ldisc.open)(tty);
        }
        if (info->blocked_open) {
                if (info->close_delay) {
                        current->state = TASK_INTERRUPTIBLE;
                        current->timeout = jiffies + info->close_delay;
                        schedule();
                }
                wake_up_interruptible(&info->open_wait);
        }
        info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CALLOUT_ACTIVE|
                         ASYNC_CLOSING);
        wake_up_interruptible(&info->close_wait);
        restore_flags(flags);
}
 
/*
 * mcfrs_hangup() --- called by tty_hangup() when a hangup is signaled.
 */
void mcfrs_hangup(struct tty_struct *tty)
{
        struct mcf_serial * info = (struct mcf_serial *)tty->driver_data;
 
        if (serial_paranoia_check(info, tty->device, "mcfrs_hangup"))
                return;
 
        mcfrs_flush_buffer(tty);
        shutdown(info);
        info->event = 0;
        info->count = 0;
        info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CALLOUT_ACTIVE);
        info->tty = 0;
        wake_up_interruptible(&info->open_wait);
}
 
/*
 * ------------------------------------------------------------
 * mcfrs_open() and friends
 * ------------------------------------------------------------
 */
static int block_til_ready(struct tty_struct *tty, struct file * filp,
                           struct mcf_serial *info)
{
        struct wait_queue wait = { current, NULL };
        int             retval;
        int             do_clocal = 0;
 
        /*
         * If the device is in the middle of being closed, then block
         * until it's done, and then try again.
         */
        if (info->flags & ASYNC_CLOSING) {
                interruptible_sleep_on(&info->close_wait);
#ifdef SERIAL_DO_RESTART
                if (info->flags & ASYNC_HUP_NOTIFY)
                        return -EAGAIN;
                else
                        return -ERESTARTSYS;
#else
                return -EAGAIN;
#endif
        }
 
        /*
         * If this is a callout device, then just make sure the normal
         * device isn't being used.
         */
        if (tty->driver.subtype == SERIAL_TYPE_CALLOUT) {
                if (info->flags & ASYNC_NORMAL_ACTIVE)
                        return -EBUSY;
                if ((info->flags & ASYNC_CALLOUT_ACTIVE) &&
                    (info->flags & ASYNC_SESSION_LOCKOUT) &&
                    (info->session != current->session))
                    return -EBUSY;
                if ((info->flags & ASYNC_CALLOUT_ACTIVE) &&
                    (info->flags & ASYNC_PGRP_LOCKOUT) &&
                    (info->pgrp != current->pgrp))
                    return -EBUSY;
                info->flags |= ASYNC_CALLOUT_ACTIVE;
                return 0;
        }
 
        /*
         * If non-blocking mode is set, or the port is not enabled,
         * then make the check up front and then exit.
         */
        if ((filp->f_flags & O_NONBLOCK) ||
            (tty->flags & (1 << TTY_IO_ERROR))) {
                if (info->flags & ASYNC_CALLOUT_ACTIVE)
                        return -EBUSY;
                info->flags |= ASYNC_NORMAL_ACTIVE;
                return 0;
        }
 
        if (info->flags & ASYNC_CALLOUT_ACTIVE) {
                if (info->normal_termios.c_cflag & CLOCAL)
                        do_clocal = 1;
        } else {
                if (tty->termios->c_cflag & CLOCAL)
                        do_clocal = 1;
        }
 
        /*
         * Block waiting for the carrier detect and the line to become
         * free (i.e., not in use by the callout).  While we are in
         * this loop, info->count is dropped by one, so that
         * mcfrs_close() knows when to free things.  We restore it upon
         * exit, either normal or abnormal.
         */
        retval = 0;
        add_wait_queue(&info->open_wait, &wait);
#ifdef SERIAL_DEBUG_OPEN
        printk("block_til_ready before block: ttyS%d, count = %d\n",
               info->line, info->count);
#endif
        info->count--;
        info->blocked_open++;
        while (1) {
                cli();
                if (!(info->flags & ASYNC_CALLOUT_ACTIVE))
                        mcfrs_setsignals(info, 1, 1);
                sti();
                current->state = TASK_INTERRUPTIBLE;
                if (tty_hung_up_p(filp) ||
                    !(info->flags & ASYNC_INITIALIZED)) {
#ifdef SERIAL_DO_RESTART
                        if (info->flags & ASYNC_HUP_NOTIFY)
                                retval = -EAGAIN;
                        else
                                retval = -ERESTARTSYS;
#else
                        retval = -EAGAIN;
#endif
                        break;
                }
                if (!(info->flags & ASYNC_CALLOUT_ACTIVE) &&
                    !(info->flags & ASYNC_CLOSING) && do_clocal)
                        break;
                if (current->signal & ~current->blocked) {
                        retval = -ERESTARTSYS;
                        break;
                }
#ifdef SERIAL_DEBUG_OPEN
                printk("block_til_ready blocking: ttyS%d, count = %d\n",
                       info->line, info->count);
#endif
                schedule();
        }
        current->state = TASK_RUNNING;
        remove_wait_queue(&info->open_wait, &wait);
        if (!tty_hung_up_p(filp))
                info->count++;
        info->blocked_open--;
#ifdef SERIAL_DEBUG_OPEN
        printk("block_til_ready after blocking: ttyS%d, count = %d\n",
               info->line, info->count);
#endif
        if (retval)
                return retval;
        info->flags |= ASYNC_NORMAL_ACTIVE;
        return 0;
}
 
/*
 * This routine is called whenever a serial port is opened. It
 * enables interrupts for a serial port, linking in its structure into
 * the IRQ chain.   It also performs the serial-specific
 * initialization for the tty structure.
 */
int mcfrs_open(struct tty_struct *tty, struct file * filp)
{
        struct mcf_serial       *info;
        int                     retval, line;
 
        line = MINOR(tty->device) - tty->driver.minor_start;
        if ((line < 0) || (line >= NR_PORTS))
                return -ENODEV;
        info = mcfrs_table + line;
        if (serial_paranoia_check(info, tty->device, "mcfrs_open"))
                return -ENODEV;
#ifdef SERIAL_DEBUG_OPEN
        printk("mcfrs_open %s%d, count = %d\n", tty->driver.name, info->line,
               info->count);
#endif
        info->count++;
        tty->driver_data = info;
        info->tty = tty;
 
        /*
         * Start up serial port
         */
        retval = startup(info);
        if (retval)
                return retval;
 
        retval = block_til_ready(tty, filp, info);
        if (retval) {
#ifdef SERIAL_DEBUG_OPEN
                printk("mcfrs_open returning after block_til_ready with %d\n",
                       retval);
#endif
                return retval;
        }
 
        if ((info->count == 1) && (info->flags & ASYNC_SPLIT_TERMIOS)) {
                if (tty->driver.subtype == SERIAL_TYPE_NORMAL)
                        *tty->termios = info->normal_termios;
                else
                        *tty->termios = info->callout_termios;
                mcfrs_change_speed(info);
        }
 
        info->session = current->session;
        info->pgrp = current->pgrp;
 
#ifdef SERIAL_DEBUG_OPEN
        printk("mcfrs_open ttyS%d successful...\n", info->line);
#endif
        return 0;
}
 
/*
 *      Based on the line number set up the internal interrupt stuff.
 */
static void mcfrs_irqinit(struct mcf_serial *info)
{
        volatile unsigned char  *icrp, *uartp;
 
#if 0
        printk("%s(%d): setting interrupt for line=%d\n", __FILE__, __LINE__,
                info->line);
#endif
 
        switch (info->line) {
 
        case 0:
                icrp = (volatile unsigned char *) (MCF_MBAR + MCFSIM_UART1ICR);
                *icrp = /*MCFSIM_ICR_AUTOVEC |*/ MCFSIM_ICR_LEVEL6 |
                        MCFSIM_ICR_PRI1;
                mcf_setimr(mcf_getimr() & ~MCFSIM_IMR_UART1);
                break;
 
        case 1:
                icrp = (volatile unsigned char *) (MCF_MBAR + MCFSIM_UART2ICR);
                *icrp = /*MCFSIM_ICR_AUTOVEC |*/ MCFSIM_ICR_LEVEL6 |
                        MCFSIM_ICR_PRI2;
                mcf_setimr(mcf_getimr() & ~MCFSIM_IMR_UART2);
                break;
 
        default:
                printk("SERIAL: don't know how to handle UART %d interrupt?\n",
                        info->line);
                return;
        }
 
        uartp = (volatile unsigned char *) info->addr;
        uartp[MCFUART_UIVR] = info->irq;
 
        if (request_irq(info->irq, mcfrs_interrupt, SA_INTERRUPT,
            "ColdFire UART", NULL)) {
                printk("SERIAL: Unable to attach ColdFire UART %d interrupt "
                        "vector=%d\n", info->line, info->irq);
        }
 
        return;
}
 
 
char *mcfrs_drivername = "ColdFire internal UART serial driver version 1.00\n";
 
 
/*
 * Serial stats reporting...
 */
int mcfrs_readproc(char *buffer)
{
        struct mcf_serial       *info;
        char                    str[20];
        int                     len, sigs, i;
 
        len = sprintf(buffer, mcfrs_drivername);
        for (i = 0; (i < NR_PORTS); i++) {
                info = &mcfrs_table[i];
                len += sprintf((buffer + len), "%d: port:%x irq=%d baud:%d ",
                        i, info->addr, info->irq, info->baud);
                if (info->stats.rx || info->stats.tx)
                        len += sprintf((buffer + len), "tx:%d rx:%d ",
                        info->stats.tx, info->stats.rx);
                if (info->stats.rxframing)
                        len += sprintf((buffer + len), "fe:%d ",
                        info->stats.rxframing);
                if (info->stats.rxparity)
                        len += sprintf((buffer + len), "pe:%d ",
                        info->stats.rxparity);
                if (info->stats.rxbreak)
                        len += sprintf((buffer + len), "brk:%d ",
                        info->stats.rxbreak);
                if (info->stats.rxoverrun)
                        len += sprintf((buffer + len), "oe:%d ",
                        info->stats.rxoverrun);
 
                str[0] = str[1] = 0;
                if ((sigs = mcfrs_getsignals(info))) {
                        if (sigs & TIOCM_RTS)
                                strcat(str, "|RTS");
                        if (sigs & TIOCM_CTS)
                                strcat(str, "|CTS");
                        if (sigs & TIOCM_DTR)
                                strcat(str, "|DTR");
                        if (sigs & TIOCM_CD)
                                strcat(str, "|CD");
                }
 
                len += sprintf((buffer + len), "%s\n", &str[1]);
        }
 
        return(len);
}
 
 
/* Finally, routines used to initialize the serial driver. */
 
static void show_serial_version(void)
{
        printk(mcfrs_drivername);
}
 
/* mcfrs_init inits the driver */
int mcfrs_init(void)
{
        struct mcf_serial       *info;
        unsigned long           flags;
        int                     i;
 
        /* Setup base handler, and timer table. */
        init_bh(SERIAL_BH, do_serial_bh);
#if defined(CONFIG_NETtel) && defined(CONFIG_M5307)
        timer_table[RS_TIMER].fn = mcfrs_timer;
        timer_table[RS_TIMER].expires = 0;
#endif
 
        show_serial_version();
 
        /* Initialize the tty_driver structure */
        memset(&mcfrs_serial_driver, 0, sizeof(struct tty_driver));
        mcfrs_serial_driver.magic = TTY_DRIVER_MAGIC;
        mcfrs_serial_driver.name = "ttyS";
        mcfrs_serial_driver.major = TTY_MAJOR;
        mcfrs_serial_driver.minor_start = 64;
        mcfrs_serial_driver.num = NR_PORTS;
        mcfrs_serial_driver.type = TTY_DRIVER_TYPE_SERIAL;
        mcfrs_serial_driver.subtype = SERIAL_TYPE_NORMAL;
        mcfrs_serial_driver.init_termios = tty_std_termios;
 
        mcfrs_serial_driver.init_termios.c_cflag =
                B9600 | CS8 | CREAD | HUPCL | CLOCAL;
        mcfrs_serial_driver.flags = TTY_DRIVER_REAL_RAW;
        mcfrs_serial_driver.refcount = &mcfrs_serial_refcount;
        mcfrs_serial_driver.table = mcfrs_serial_table;
        mcfrs_serial_driver.termios = mcfrs_serial_termios;
        mcfrs_serial_driver.termios_locked = mcfrs_serial_termios_locked;
 
        mcfrs_serial_driver.open = mcfrs_open;
        mcfrs_serial_driver.close = mcfrs_close;
        mcfrs_serial_driver.write = mcfrs_write;
        mcfrs_serial_driver.flush_chars = mcfrs_flush_chars;
        mcfrs_serial_driver.write_room = mcfrs_write_room;
        mcfrs_serial_driver.chars_in_buffer = mcfrs_chars_in_buffer;
        mcfrs_serial_driver.flush_buffer = mcfrs_flush_buffer;
        mcfrs_serial_driver.ioctl = mcfrs_ioctl;
        mcfrs_serial_driver.throttle = mcfrs_throttle;
        mcfrs_serial_driver.unthrottle = mcfrs_unthrottle;
        mcfrs_serial_driver.set_termios = mcfrs_set_termios;
        mcfrs_serial_driver.stop = mcfrs_stop;
        mcfrs_serial_driver.start = mcfrs_start;
        mcfrs_serial_driver.hangup = mcfrs_hangup;
 
        /*
         * The callout device is just like normal device except for
         * major number and the subtype code.
         */
        mcfrs_callout_driver = mcfrs_serial_driver;
        mcfrs_callout_driver.name = "cua";
        mcfrs_callout_driver.major = TTYAUX_MAJOR;
        mcfrs_callout_driver.subtype = SERIAL_TYPE_CALLOUT;
 
        if (tty_register_driver(&mcfrs_serial_driver))
                panic("Couldn't register serial driver\n");
        if (tty_register_driver(&mcfrs_callout_driver))
                panic("Couldn't register callout driver\n");
 
        save_flags(flags); cli();
 
        /*
         *      Configure all the attached serial ports.
         */
        for (i = 0, info = mcfrs_table; (i < NR_PORTS); i++, info++) {
                info->magic = SERIAL_MAGIC;
                info->line = i;
                info->tty = 0;
                info->custom_divisor = 16;
                info->close_delay = 50;
                info->closing_wait = 3000;
                info->x_char = 0;
                info->event = 0;
                info->count = 0;
                info->blocked_open = 0;
                info->tqueue.routine = do_softint;
                info->tqueue.data = info;
                info->tqueue_hangup.routine = do_serial_hangup;
                info->tqueue_hangup.data = info;
                info->callout_termios = mcfrs_callout_driver.init_termios;
                info->normal_termios = mcfrs_serial_driver.init_termios;
                info->open_wait = 0;
                info->close_wait = 0;
 
                mcfrs_setsignals(info, 0, 0);
                mcfrs_irqinit(info);
 
                printk("%s%d at 0x%04x (irq = %d)", mcfrs_serial_driver.name,
                        info->line, info->addr, info->irq);
                printk(" is a builtin ColdFire UART\n");
        }
 
        restore_flags(flags);
        return 0;
}
 
/****************************************************************************/
/*                          Serial Console                                  */
/****************************************************************************/
 
/*
 *      Quick and dirty UART initialization, for console output.
 */
 
void rs_console_init(void)
{
        volatile unsigned char  *uartp;
        unsigned int            clk;
 
        /*
         *      Reset UART, get it into known state...
         */
        uartp = (volatile unsigned char *) (MCF_MBAR +
                (mcfrs_console_port ? MCFUART_BASE2 : MCFUART_BASE1));
 
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETRX;  /* reset RX */
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETTX;  /* reset TX */
        uartp[MCFUART_UCR] = MCFUART_UCR_CMDRESETMRPTR;  /* reset MR pointer */
 
        /*
         * Set port for defined baud , 8 data bits, 1 stop bit, no parity.
         */
        uartp[MCFUART_UMR] = MCFUART_MR1_PARITYNONE | MCFUART_MR1_CS8;
        uartp[MCFUART_UMR] = MCFUART_MR2_STOP1;
 
        clk = ((MCF_CLK / 32) / mcfrs_console_baud);  /* Set baud above */
        uartp[MCFUART_UBG1] = (clk & 0xff00) >> 8;  /* set msb baud */
        uartp[MCFUART_UBG2] = (clk & 0xff);  /* set lsb baud */
 
        uartp[MCFUART_UCSR] = MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER;
        uartp[MCFUART_UCR] = MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE;
 
        mcfrs_console_inited++;
        return;
}
 
 
/*
 *      Setup for console. Argument comes from the boot command line.
 */
 
int rs_console_setup(char *arg)
{
        int     rc = 0;
 
        if (!strncmp(arg, "/dev/ttyS", 9)) {
                mcfrs_console_port = arg[9] - '0';
                arg += 10;
                rc = 1;
        } else if (!strncmp(arg, "/dev/cua", 8)) {
                mcfrs_console_port = arg[8] - '0';
                arg += 9;
                rc = 1;
        }
        if (*arg == ',')
                mcfrs_console_baud = simple_strtoul(arg+1,NULL,0);
        return(rc);
}
 
 
/*
 *      Output a single character, using UART polled mode.
 *      This is ised for console output.
 */
 
void rs_put_char(char ch)
{
        volatile unsigned char  *uartp;
        unsigned long           flags;
        int                     i;
 
        uartp = (volatile unsigned char *) (MCF_MBAR +
                (mcfrs_console_port ? MCFUART_BASE2 : MCFUART_BASE1));
 
        save_flags(flags); cli();
        for (i = 0; (i < 0x10000); i++) {
                if (uartp[MCFUART_USR] & MCFUART_USR_TXREADY)
                        break;
        }
        uartp[MCFUART_UTB] = ch;
        restore_flags(flags);
 
        return;
}
 
 
/*
 * rs_console_print is registered for printk output.
 */
 
void rs_console_print(const char *p)
{
        char c;
 
        while ((c = *(p++)) != 0) {
                if(c == '\n')
                        rs_put_char('\r');
                rs_put_char(c);
        }
        return;
}
 
/****************************************************************************/
Browse

Tools

Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [char/] [mcfserial.c] - Blame information for rev 1765

Line No.	Rev	Author	Line
1	1626	jcastillo	`/*`
2			`* mcfserial.c -- serial driver for ColdFire internal UARTS.`
3			`*`
4			`* Copyright (C) 1999 Greg Ungerer (gerg@moreton.com.au)`
5			`*`
6			`* Based on code from 68332serial.c which was:`
7			`*`
8			`* Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)`
9			`* Copyright (C) 1998 TSHG`
10			`*/`
11
12			`#include <linux/errno.h>`
13			`#include <linux/signal.h>`
14			`#include <linux/sched.h>`
15			`#include <linux/timer.h>`
16			`#include <linux/interrupt.h>`
17			`#include <linux/tty.h>`
18			`#include <linux/tty_flip.h>`
19			`#include <linux/config.h>`
20			`#include <linux/major.h>`
21			`#include <linux/string.h>`
22			`#include <linux/fcntl.h>`
23			`#include <linux/mm.h>`
24			`#include <linux/kernel.h>`
25
26			`#include <asm/io.h>`
27			`#include <asm/irq.h>`
28			`#include <asm/system.h>`
29			`#include <asm/segment.h>`
30			`#include <asm/bitops.h>`
31			`#include <asm/delay.h>`
32			`#include <asm/coldfire.h>`
33			`#include <asm/mcfsim.h>`
34			`#include <asm/mcfuart.h>`
35			`#include <asm/nettel.h>`
36			`#include "mcfserial.h"`
37
38
39			`/*`
40			`* Default console port and baud rate...`