URL https://opencores.org/ocsvn/or1k/or1k/trunk

Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [net/] [3c505.h] - Blame information for rev 1626

Go to most recent revision | Details | Compare with Previous | View Log


/*****************************************************************
 *
 *  defines for 3Com Etherlink Plus adapter
 *
 *****************************************************************/
 
/*
 * I/O register offsets
 */
#define PORT_COMMAND    0x00    /* read/write, 8-bit */
#define PORT_STATUS     0x02    /* read only, 8-bit */
#define PORT_AUXDMA     0x02    /* write only, 8-bit */
#define PORT_DATA       0x04    /* read/write, 16-bit */
#define PORT_CONTROL    0x06    /* read/write, 8-bit */
 
#define ELP_IO_EXTENT   0x10    /* size of used IO registers */
 
/*
 * host control registers bits
 */
#define ATTN    0x80    /* attention */
#define FLSH    0x40    /* flush data register */
#define DMAE    0x20    /* DMA enable */
#define DIR     0x10    /* direction */
#define TCEN    0x08    /* terminal count interrupt enable */
#define CMDE    0x04    /* command register interrupt enable */
#define HSF2    0x02    /* host status flag 2 */
#define HSF1    0x01    /* host status flag 1 */
 
/*
 * combinations of HSF flags used for PCB transmission
 */
#define HSF_PCB_ACK     HSF1
#define HSF_PCB_NAK     HSF2
#define HSF_PCB_END     (HSF2|HSF1)
#define HSF_PCB_MASK    (HSF2|HSF1)
 
/*
 * host status register bits
 */
#define HRDY    0x80    /* data register ready */
#define HCRE    0x40    /* command register empty */
#define ACRF    0x20    /* adapter command register full */
/* #define DIR  0x10    direction - same as in control register */
#define DONE    0x08    /* DMA done */
#define ASF3    0x04    /* adapter status flag 3 */
#define ASF2    0x02    /* adapter status flag 2 */
#define ASF1    0x01    /* adapter status flag 1 */
 
/*
 * combinations of ASF flags used for PCB reception
 */
#define ASF_PCB_ACK     ASF1
#define ASF_PCB_NAK     ASF2
#define ASF_PCB_END     (ASF2|ASF1)
#define ASF_PCB_MASK    (ASF2|ASF1)
 
/*
 * host aux DMA register bits
 */
#define DMA_BRST        0x01    /* DMA burst */
 
/*
 * maximum amount of data allowed in a PCB
 */
#define MAX_PCB_DATA    62
 
/*****************************************************************
 *
 *  timeout value
 *      this is a rough value used for loops to stop them from
 *      locking up the whole machine in the case of failure or
 *      error conditions
 *
 *****************************************************************/
 
#define TIMEOUT 300
 
/*****************************************************************
 *
 * PCB commands
 *
 *****************************************************************/
 
enum {
  /*
   * host PCB commands
   */
  CMD_CONFIGURE_ADAPTER_MEMORY  = 0x01,
  CMD_CONFIGURE_82586           = 0x02,
  CMD_STATION_ADDRESS           = 0x03,
  CMD_DMA_DOWNLOAD              = 0x04,
  CMD_DMA_UPLOAD                = 0x05,
  CMD_PIO_DOWNLOAD              = 0x06,
  CMD_PIO_UPLOAD                = 0x07,
  CMD_RECEIVE_PACKET            = 0x08,
  CMD_TRANSMIT_PACKET           = 0x09,
  CMD_NETWORK_STATISTICS        = 0x0a,
  CMD_LOAD_MULTICAST_LIST       = 0x0b,
  CMD_CLEAR_PROGRAM             = 0x0c,
  CMD_DOWNLOAD_PROGRAM          = 0x0d,
  CMD_EXECUTE_PROGRAM           = 0x0e,
  CMD_SELF_TEST                 = 0x0f,
  CMD_SET_STATION_ADDRESS       = 0x10,
  CMD_ADAPTER_INFO              = 0x11,
  NUM_TRANSMIT_CMDS,
 
  /*
   * adapter PCB commands
   */
  CMD_CONFIGURE_ADAPTER_RESPONSE        = 0x31,
  CMD_CONFIGURE_82586_RESPONSE          = 0x32,
  CMD_ADDRESS_RESPONSE                  = 0x33,
  CMD_DOWNLOAD_DATA_REQUEST             = 0x34,
  CMD_UPLOAD_DATA_REQUEST               = 0x35,
  CMD_RECEIVE_PACKET_COMPLETE           = 0x38,
  CMD_TRANSMIT_PACKET_COMPLETE          = 0x39,
  CMD_NETWORK_STATISTICS_RESPONSE       = 0x3a,
  CMD_LOAD_MULTICAST_RESPONSE           = 0x3b,
  CMD_CLEAR_PROGRAM_RESPONSE            = 0x3c,
  CMD_DOWNLOAD_PROGRAM_RESPONSE         = 0x3d,
  CMD_EXECUTE_RESPONSE                  = 0x3e,
  CMD_SELF_TEST_RESPONSE                = 0x3f,
  CMD_SET_ADDRESS_RESPONSE              = 0x40,
  CMD_ADAPTER_INFO_RESPONSE             = 0x41
};
 
/* Definitions for the PCB data structure */
 
/* Data units */
typedef unsigned char         byte;
typedef unsigned short int    word;
typedef unsigned long int     dword;
 
/* Data structures */
struct Memconf {
        word    cmd_q,
                rcv_q,
                mcast,
                frame,
                rcv_b,
                progs;
};
 
struct Rcv_pkt {
        word    buf_ofs,
                buf_seg,
                buf_len,
                timeout;
};
 
struct Xmit_pkt {
        word    buf_ofs,
                buf_seg,
                pkt_len;
};
 
struct Rcv_resp {
        word    buf_ofs,
                buf_seg,
                buf_len,
                pkt_len,
                timeout,
                status;
        dword   timetag;
};
 
struct Xmit_resp {
        word    buf_ofs,
                buf_seg,
                c_stat,
                status;
};
 
 
struct Netstat {
        dword   tot_recv,
                tot_xmit;
        word    err_CRC,
                err_align,
                err_res,
                err_ovrrun;
};
 
 
struct Selftest {
        word    error;
        union {
                word ROM_cksum;
                struct {
                        word ofs, seg;
                } RAM;
                word i82586;
        } failure;
};
 
struct Info {
        byte    minor_vers,
                major_vers;
        word    ROM_cksum,
                RAM_sz,
                free_ofs,
                free_seg;
};
 
struct Memdump {
       word size,
            off,
            seg;
};
 
/*
Primary Command Block. The most important data structure. All communication
between the host and the adapter is done with these. (Except for the actual
ethernet data, which has different packaging.)
*/
typedef struct {
        byte    command;
        byte    length;
        union   {
                struct Memconf          memconf;
                word                    configure;
                struct Rcv_pkt          rcv_pkt;
                struct Xmit_pkt         xmit_pkt;
                byte                    multicast[10][6];
                byte                    eth_addr[6];
                byte                    failed;
                struct Rcv_resp         rcv_resp;
                struct Xmit_resp        xmit_resp;
                struct Netstat          netstat;
                struct Selftest         selftest;
                struct Info             info;
                struct Memdump          memdump;
                byte                    raw[62];
        } data;
} pcb_struct;
 
/* These defines for 'configure' */
#define RECV_STATION    0x00
#define RECV_BROAD      0x01
#define RECV_MULTI      0x02
#define RECV_PROMISC    0x04
#define NO_LOOPBACK     0x00
#define INT_LOOPBACK    0x08
#define EXT_LOOPBACK    0x10

Browse

Tools

Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [net/] [3c505.h] - Blame information for rev 1626

Line No.	Rev	Author	Line
1	1626	jcastillo	`/*****************************************************************`
2			`*`
3			`* defines for 3Com Etherlink Plus adapter`
4			`*`
5			`*****************************************************************/`
6
7			`/*`
8			`* I/O register offsets`
9			`*/`
10			`#define PORT_COMMAND 0x00 /* read/write, 8-bit */`
11			`#define PORT_STATUS 0x02 /* read only, 8-bit */`
12			`#define PORT_AUXDMA 0x02 /* write only, 8-bit */`
13			`#define PORT_DATA 0x04 /* read/write, 16-bit */`
14			`#define PORT_CONTROL 0x06 /* read/write, 8-bit */`
15
16			`#define ELP_IO_EXTENT 0x10 /* size of used IO registers */`
17
18			`/*`
19			`* host control registers bits`
20			`*/`
21			`#define ATTN 0x80 /* attention */`
22			`#define FLSH 0x40 /* flush data register */`
23			`#define DMAE 0x20 /* DMA enable */`
24			`#define DIR 0x10 /* direction */`
25			`#define TCEN 0x08 /* terminal count interrupt enable */`
26			`#define CMDE 0x04 /* command register interrupt enable */`
27			`#define HSF2 0x02 /* host status flag 2 */`
28			`#define HSF1 0x01 /* host status flag 1 */`
29
30			`/*`
31			`* combinations of HSF flags used for PCB transmission`
32			`*/`
33			`#define HSF_PCB_ACK HSF1`
34			`#define HSF_PCB_NAK HSF2`
35			`#define HSF_PCB_END (HSF2\|HSF1)`
36			`#define HSF_PCB_MASK (HSF2\|HSF1)`
37
38			`/*`
39			`* host status register bits`
40			`*/`
41			`#define HRDY 0x80 /* data register ready */`
42			`#define HCRE 0x40 /* command register empty */`
43			`#define ACRF 0x20 /* adapter command register full */`
44			`/* #define DIR 0x10 direction - same as in control register */`
45			`#define DONE 0x08 /* DMA done */`
46			`#define ASF3 0x04 /* adapter status flag 3 */`
47			`#define ASF2 0x02 /* adapter status flag 2 */`
48			`#define ASF1 0x01 /* adapter status flag 1 */`
49
50			`/*`
51			`* combinations of ASF flags used for PCB reception`
52			`*/`
53			`#define ASF_PCB_ACK ASF1`
54			`#define ASF_PCB_NAK ASF2`
55			`#define ASF_PCB_END (ASF2\|ASF1)`
56			`#define ASF_PCB_MASK (ASF2\|ASF1)`
57
58			`/*`
59			`* host aux DMA register bits`
60			`*/`
61			`#define DMA_BRST 0x01 /* DMA burst */`
62
63			`/*`
64			`* maximum amount of data allowed in a PCB`
65			`*/`
66			`#define MAX_PCB_DATA 62`
67
68			`/*****************************************************************`
69			`*`
70			`* timeout value`
71			`* this is a rough value used for loops to stop them from`
72			`* locking up the whole machine in the case of failure or`
73			`* error conditions`
74			`*`
75			`*****************************************************************/`
76
77			`#define TIMEOUT 300`
78
79			`/*****************************************************************`
80			`*`
81			`* PCB commands`
82			`*`
83			`*****************************************************************/`
84
85			`enum {`
86			`/*`
87			`* host PCB commands`
88			`*/`
89			`CMD_CONFIGURE_ADAPTER_MEMORY = 0x01,`
90			`CMD_CONFIGURE_82586 = 0x02,`
91			`CMD_STATION_ADDRESS = 0x03,`
92			`CMD_DMA_DOWNLOAD = 0x04,`
93			`CMD_DMA_UPLOAD = 0x05,`
94			`CMD_PIO_DOWNLOAD = 0x06,`
95			`CMD_PIO_UPLOAD = 0x07,`
96			`CMD_RECEIVE_PACKET = 0x08,`
97			`CMD_TRANSMIT_PACKET = 0x09,`
98			`CMD_NETWORK_STATISTICS = 0x0a,`
99			`CMD_LOAD_MULTICAST_LIST = 0x0b,`
100			`CMD_CLEAR_PROGRAM = 0x0c,`
101			`CMD_DOWNLOAD_PROGRAM = 0x0d,`
102			`CMD_EXECUTE_PROGRAM = 0x0e,`
103			`CMD_SELF_TEST = 0x0f,`
104			`CMD_SET_STATION_ADDRESS = 0x10,`
105			`CMD_ADAPTER_INFO = 0x11,`
106			`NUM_TRANSMIT_CMDS,`
107
108			`/*`
109			`* adapter PCB commands`
110			`*/`
111			`CMD_CONFIGURE_ADAPTER_RESPONSE = 0x31,`
112			`CMD_CONFIGURE_82586_RESPONSE = 0x32,`
113			`CMD_ADDRESS_RESPONSE = 0x33,`
114			`CMD_DOWNLOAD_DATA_REQUEST = 0x34,`
115			`CMD_UPLOAD_DATA_REQUEST = 0x35,`
116			`CMD_RECEIVE_PACKET_COMPLETE = 0x38,`
117			`CMD_TRANSMIT_PACKET_COMPLETE = 0x39,`
118			`CMD_NETWORK_STATISTICS_RESPONSE = 0x3a,`
119			`CMD_LOAD_MULTICAST_RESPONSE = 0x3b,`
120			`CMD_CLEAR_PROGRAM_RESPONSE = 0x3c,`
121			`CMD_DOWNLOAD_PROGRAM_RESPONSE = 0x3d,`
122			`CMD_EXECUTE_RESPONSE = 0x3e,`
123			`CMD_SELF_TEST_RESPONSE = 0x3f,`
124			`CMD_SET_ADDRESS_RESPONSE = 0x40,`
125			`CMD_ADAPTER_INFO_RESPONSE = 0x41`
126			`};`
127
128			`/* Definitions for the PCB data structure */`
129
130			`/* Data units */`
131			`typedef unsigned char byte;`
132			`typedef unsigned short int word;`
133			`typedef unsigned long int dword;`
134
135			`/* Data structures */`
136			`struct Memconf {`
137			`word cmd_q,`
138			`rcv_q,`
139			`mcast,`
140			`frame,`
141			`rcv_b,`
142			`progs;`
143			`};`
144
145			`struct Rcv_pkt {`
146			`word buf_ofs,`
147			`buf_seg,`
148			`buf_len,`
149			`timeout;`
150			`};`
151
152			`struct Xmit_pkt {`
153			`word buf_ofs,`
154			`buf_seg,`
155			`pkt_len;`
156			`};`
157
158			`struct Rcv_resp {`
159			`word buf_ofs,`
160			`buf_seg,`
161			`buf_len,`
162			`pkt_len,`
163			`timeout,`
164			`status;`
165			`dword timetag;`
166			`};`
167
168			`struct Xmit_resp {`
169			`word buf_ofs,`
170			`buf_seg,`
171			`c_stat,`
172			`status;`
173			`};`
174
175
176			`struct Netstat {`
177			`dword tot_recv,`
178			`tot_xmit;`
179			`word err_CRC,`
180			`err_align,`
181			`err_res,`
182			`err_ovrrun;`
183			`};`
184
185
186			`struct Selftest {`
187			`word error;`
188			`union {`
189			`word ROM_cksum;`
190			`struct {`
191			`word ofs, seg;`
192			`} RAM;`
193			`word i82586;`
194			`} failure;`
195			`};`
196
197			`struct Info {`
198			`byte minor_vers,`
199			`major_vers;`
200			`word ROM_cksum,`
201			`RAM_sz,`
202			`free_ofs,`
203			`free_seg;`
204			`};`
205
206			`struct Memdump {`
207			`word size,`
208			`off,`
209			`seg;`
210			`};`
211
212			`/*`
213			`Primary Command Block. The most important data structure. All communication`
214			`between the host and the adapter is done with these. (Except for the actual`
215			`ethernet data, which has different packaging.)`
216			`*/`
217			`typedef struct {`
218			`byte command;`
219			`byte length;`
220			`union {`
221			`struct Memconf memconf;`
222			`word configure;`
223			`struct Rcv_pkt rcv_pkt;`
224			`struct Xmit_pkt xmit_pkt;`
225			`byte multicast[10][6];`
226			`byte eth_addr[6];`
227			`byte failed;`
228			`struct Rcv_resp rcv_resp;`
229			`struct Xmit_resp xmit_resp;`
230			`struct Netstat netstat;`
231			`struct Selftest selftest;`
232			`struct Info info;`
233			`struct Memdump memdump;`
234			`byte raw[62];`
235			`} data;`
236			`} pcb_struct;`
237
238			`/* These defines for 'configure' */`
239			`#define RECV_STATION 0x00`
240			`#define RECV_BROAD 0x01`
241			`#define RECV_MULTI 0x02`
242			`#define RECV_PROMISC 0x04`
243			`#define NO_LOOPBACK 0x00`
244			`#define INT_LOOPBACK 0x08`
245			`#define EXT_LOOPBACK 0x10`