Subversion Repositories or1k

/* atarilance.c: Ethernet driver for VME Lance cards on the Atari */

/*

        Written 1995/96 by Roman Hodek (Roman.Hodek@informatik.uni-erlangen.de)

        This software may be used and distributed according to the terms

        of the GNU Public License, incorporated herein by reference.

        This drivers was written with the following sources of reference:

         - The driver for the Riebl Lance card by the TU Vienna.

         - The modified TUW driver for PAM's VME cards

         - The PC-Linux driver for Lance cards (but this is for bus master

       cards, not the shared memory ones)

         - The Amiga Ariadne driver

        v1.0: (in 1.2.13pl4/0.9.13)

              Initial version

        v1.1: (in 1.2.13pl5)

              more comments

                  deleted some debugging stuff

                  optimized register access (keep AREG pointing to CSR0)

                  following AMD, CSR0_STRT should be set only after IDON is detected

                  use memcpy() for data transfers, that also employs long word moves

                  better probe procedure for 24-bit systems

          non-VME-RieblCards need extra delays in memcpy

                  must also do write test, since 0xfxe00000 may hit ROM

                  use 8/32 tx/rx buffers, which should give better NFS performance;

                    this is made possible by shifting the last packet buffer after the

                    RieblCard reserved area

    v1.2: (in 1.2.13pl8)

              again fixed probing for the Falcon; 0xfe01000 hits phys. 0x00010000

                  and thus RAM, in case of no Lance found all memory contents have to

                  be restored!

                  Now possible to compile as module.

        v1.3: 03/30/96 Jes Sorensen, Roman (in 1.3)

              Several little 1.3 adaptions

                  When the lance is stopped it jumps back into little-endian

                  mode. It is therefore necessary to put it back where it

                  belongs, in big endian mode, in order to make things work.

                  This might be the reason why multicast-mode didn't work

                  before, but I'm not able to test it as I only got an Amiga

                  (we had similar problems with the A2065 driver).

*/

static char *version = "atarilance.c: v1.3 04/04/96 "

                                           "Roman.Hodek@informatik.uni-erlangen.de\n";

#include <linux/module.h>

#include <linux/stddef.h>

#include <linux/kernel.h>

#include <linux/sched.h>

#include <linux/string.h>

#include <linux/ptrace.h>

#include <linux/errno.h>

#include <linux/malloc.h>

#include <linux/interrupt.h>

#include <asm/irq.h>

#include <asm/atarihw.h>

#include <asm/atariints.h>

#include <asm/bitops.h>

#include <asm/io.h>

#include <asm/bootinfo.h>

#include <linux/netdevice.h>

#include <linux/etherdevice.h>

#include <linux/skbuff.h>

/* Debug level:

 *  0 = silent, print only serious errors

 *  1 = normal, print error messages

 *  2 = debug, print debug infos

 *  3 = debug, print even more debug infos (packet data)

 */

#define LANCE_DEBUG     1

#ifdef LANCE_DEBUG

static int lance_debug = LANCE_DEBUG;

#else

static int lance_debug = 1;

#endif

/* Print debug messages on probing? */

#undef LANCE_DEBUG_PROBE

#define DPRINTK(n,a)                                                    \

        do {                                                                            \

                if (lance_debug >= n)                                   \

                        printk a;                                                       \

        } while( 0 )

#ifdef LANCE_DEBUG_PROBE

# define PROBE_PRINT(a) printk a

#else

# define PROBE_PRINT(a) 

#endif

/* These define the number of Rx and Tx buffers as log2. (Only powers

 * of two are valid)

 * Much more rx buffers (32) are reserved than tx buffers (8), since receiving

 * is more time critical then sending and packets may have to remain in the

 * board's memory when main memory is low.

 */

#define TX_LOG_RING_SIZE                        3

#define RX_LOG_RING_SIZE                        5

/* These are the derived values */

#define TX_RING_SIZE                    (1 << TX_LOG_RING_SIZE)

#define TX_RING_LEN_BITS                (TX_LOG_RING_SIZE << 5)

#define TX_RING_MOD_MASK                (TX_RING_SIZE - 1)

#define RX_RING_SIZE                    (1 << RX_LOG_RING_SIZE)

#define RX_RING_LEN_BITS                (RX_LOG_RING_SIZE << 5)

#define RX_RING_MOD_MASK                (RX_RING_SIZE - 1)

/* The LANCE Rx and Tx ring descriptors. */

struct lance_rx_head {

        unsigned short                  base;           /* Low word of base addr */

        volatile unsigned char  flag;

        unsigned char                   base_hi;        /* High word of base addr (unused) */

        short                                   buf_length;     /* This length is 2s complement! */

        volatile short                  msg_length;     /* This length is "normal". */

};

struct lance_tx_head {

        unsigned short                  base;           /* Low word of base addr */

        volatile unsigned char  flag;

        unsigned char                   base_hi;        /* High word of base addr (unused) */

        short                                   length;         /* Length is 2s complement! */

        volatile short                  misc;

};

struct ringdesc {

        unsigned short  adr_lo;         /* Low 16 bits of address */

        unsigned char   len;            /* Length bits */

        unsigned char   adr_hi;         /* High 8 bits of address (unused) */

};

/* The LANCE initialization block, described in databook. */

struct lance_init_block {

        unsigned short  mode;           /* Pre-set mode */

        unsigned char   hwaddr[6];      /* Physical ethernet address */

        unsigned                filter[2];      /* Multicast filter (unused). */

        /* Receive and transmit ring base, along with length bits. */

        struct ringdesc rx_ring;

        struct ringdesc tx_ring;

};

/* The whole layout of the Lance shared memory */

struct lance_memory {

        struct lance_init_block init;

        struct lance_tx_head    tx_head[TX_RING_SIZE];

        struct lance_rx_head    rx_head[RX_RING_SIZE];

        char                                    packet_area[0];  /* packet data follow after the

                                                                                         * init block and the ring

                                                                                         * descriptors and are located

                                                                                         * at runtime */

};

/* RieblCard specifics:

 * The original TOS driver for these cards reserves the area from offset

 * 0xee70 to 0xeebb for storing configuration data. Of interest to us is the

 * Ethernet address there, and the magic for verifying the data's validity.

 * The reserved area isn't touch by packet buffers. Furthermore, offset 0xfffe

 * is reserved for the interrupt vector number.

 */

#define RIEBL_RSVD_START        0xee70

#define RIEBL_RSVD_END          0xeec0

#define RIEBL_MAGIC                     0x09051990

#define RIEBL_MAGIC_ADDR        ((unsigned long *)(((char *)MEM) + 0xee8a))

#define RIEBL_HWADDR_ADDR       ((unsigned char *)(((char *)MEM) + 0xee8e))

#define RIEBL_IVEC_ADDR         ((unsigned short *)(((char *)MEM) + 0xfffe))

/* This is a default address for the old RieblCards without a battery

 * that have no ethernet address at boot time. 00:00:36:04 is the

 * prefix for Riebl cards, the 00:00 at the end is arbitrary.

 */

static unsigned char OldRieblDefHwaddr[6] = {

        0x00, 0x00, 0x36, 0x04, 0x00, 0x00

};

/* I/O registers of the Lance chip */

struct lance_ioreg {

/* base+0x0 */  volatile unsigned short data;

/* base+0x2 */  volatile unsigned short addr;

                                unsigned char                   _dummy1[3];

/* base+0x7 */  volatile unsigned char  ivec;

                                unsigned char                   _dummy2[5];

/* base+0xd */  volatile unsigned char  eeprom;

                                unsigned char                   _dummy3;

/* base+0xf */  volatile unsigned char  mem;

};

/* Types of boards this driver supports */

enum lance_type {

        OLD_RIEBL,              /* old Riebl card without battery */

        NEW_RIEBL,              /* new Riebl card with battery */

        PAM_CARD                /* PAM card with EEPROM */

};

static char *lance_names[] = {

        "Riebl-Card (without battery)",

        "Riebl-Card (with battery)",

        "PAM intern card"

};

/* The driver's private device structure */

struct lance_private {

        enum lance_type         cardtype;

        struct lance_ioreg      *iobase;

        struct lance_memory     *mem;

        int                                     cur_rx, cur_tx; /* The next free ring entry */

        int                                     dirty_tx;               /* Ring entries to be freed. */

                                                /* copy function */

        void                            *(*memcpy_f)( void *, const void *, size_t );

        struct enet_statistics stats;

/* These two must be ints for set_bit() */

        int                                     tx_full;

        int                                     lock;

};

/* I/O register access macros */

#define MEM             lp->mem

#define DREG    IO->data

#define AREG    IO->addr

#define REGA(a) ( AREG = (a), DREG )

/* Definitions for packet buffer access: */

#define PKT_BUF_SZ              1544

/* Get the address of a packet buffer corresponding to a given buffer head */

#define PKTBUF_ADDR(head)       (((unsigned char *)(MEM)) + (head)->base)

/* Possible memory/IO addresses for probing */

struct lance_addr {

        unsigned long   memaddr;

        unsigned long   ioaddr;

        int                             slow_flag;

} lance_addr_list[] = {

        { 0xfe010000, 0xfe00fff0, 0 },   /* RieblCard VME in TT */

        { 0xffc10000, 0xffc0fff0, 0 },   /* RieblCard VME in MegaSTE

                                                                           (highest byte stripped) */

        { 0xffe00000, 0xffff7000, 1 },  /* RieblCard in ST

                                                                           (highest byte stripped) */

        { 0xffd00000, 0xffff7000, 1 },  /* RieblCard in ST with hw modif. to

                                                                           avoid conflict with ROM

                                                                           (highest byte stripped) */

        { 0xffcf0000, 0xffcffff0, 0 },   /* PAMCard VME in TT and MSTE

                                                                           (highest byte stripped) */

};

#define N_LANCE_ADDR    (sizeof(lance_addr_list)/sizeof(*lance_addr_list))

/* Definitions for the Lance */

/* tx_head flags */

#define TMD1_ENP                0x01    /* end of packet */

#define TMD1_STP                0x02    /* start of packet */

#define TMD1_DEF                0x04    /* deferred */

#define TMD1_ONE                0x08    /* one retry needed */

#define TMD1_MORE               0x10    /* more than one retry needed */

#define TMD1_ERR                0x40    /* error summary */

#define TMD1_OWN                0x80    /* ownership (set: chip owns) */

#define TMD1_OWN_CHIP   TMD1_OWN

#define TMD1_OWN_HOST   0

/* tx_head misc field */

#define TMD3_TDR                0x03FF  /* Time Domain Reflectometry counter */

#define TMD3_RTRY               0x0400  /* failed after 16 retries */

#define TMD3_LCAR               0x0800  /* carrier lost */

#define TMD3_LCOL               0x1000  /* late collision */

#define TMD3_UFLO               0x4000  /* underflow (late memory) */

#define TMD3_BUFF               0x8000  /* buffering error (no ENP) */

/* rx_head flags */

#define RMD1_ENP                0x01    /* end of packet */

#define RMD1_STP                0x02    /* start of packet */

#define RMD1_BUFF               0x04    /* buffer error */

#define RMD1_CRC                0x08    /* CRC error */

#define RMD1_OFLO               0x10    /* overflow */

#define RMD1_FRAM               0x20    /* framing error */

#define RMD1_ERR                0x40    /* error summary */

#define RMD1_OWN                0x80    /* ownership (set: ship owns) */

#define RMD1_OWN_CHIP   RMD1_OWN

#define RMD1_OWN_HOST   0

/* register names */

#define CSR0    0                /* mode/status */

#define CSR1    1               /* init block addr (low) */

#define CSR2    2               /* init block addr (high) */

#define CSR3    3               /* misc */

#define CSR8    8               /* address filter */

#define CSR15   15              /* promiscuous mode */

/* CSR0 */

/* (R=readable, W=writeable, S=set on write, C=clear on write) */

#define CSR0_INIT       0x0001          /* initialize (RS) */

#define CSR0_STRT       0x0002          /* start (RS) */

#define CSR0_STOP       0x0004          /* stop (RS) */

#define CSR0_TDMD       0x0008          /* transmit demand (RS) */

#define CSR0_TXON       0x0010          /* transmitter on (R) */

#define CSR0_RXON       0x0020          /* receiver on (R) */

#define CSR0_INEA       0x0040          /* interrupt enable (RW) */

#define CSR0_INTR       0x0080          /* interrupt active (R) */

#define CSR0_IDON       0x0100          /* initialization done (RC) */

#define CSR0_TINT       0x0200          /* transmitter interrupt (RC) */

#define CSR0_RINT       0x0400          /* receiver interrupt (RC) */

#define CSR0_MERR       0x0800          /* memory error (RC) */

#define CSR0_MISS       0x1000          /* missed frame (RC) */

#define CSR0_CERR       0x2000          /* carrier error (no heartbeat :-) (RC) */

#define CSR0_BABL       0x4000          /* babble: tx-ed too many bits (RC) */

#define CSR0_ERR        0x8000          /* error (RC) */

/* CSR3 */

#define CSR3_BCON       0x0001          /* byte control */

#define CSR3_ACON       0x0002          /* ALE control */

#define CSR3_BSWP       0x0004          /* byte swap (1=big endian) */

/***************************** Prototypes *****************************/

static int addr_accessible( volatile void *regp, int wordflag, int

                            writeflag );

static unsigned long lance_probe1( struct device *dev, struct lance_addr

                                   *init_rec );

static int lance_open( struct device *dev );

static void lance_init_ring( struct device *dev );

static int lance_start_xmit( struct sk_buff *skb, struct device *dev );

static void lance_interrupt( int irq, struct pt_regs *fp, struct device

                             *dev );

static int lance_rx( struct device *dev );

static int lance_close( struct device *dev );

static struct enet_statistics *lance_get_stats( struct device *dev );

static void set_multicast_list( struct device *dev );

static int lance_set_mac_address( struct device *dev, void *addr );

/************************* End of Prototypes **************************/

void *slow_memcpy( void *dst, const void *src, size_t len )

{       char *cto = dst;

        const char *cfrom = src;

        while( len-- ) {

                *cto++ = *cfrom++;

                MFPDELAY();

        }

        return( dst );

}

int atarilance_probe( struct device *dev )

{       int i;

        static int found = 0;

        if (!MACH_IS_ATARI || found)

                /* Assume there's only one board possible... That seems true, since

                 * the Riebl/PAM board's address cannot be changed. */

                return( ENODEV );

        for( i = 0; i < N_LANCE_ADDR; ++i ) {

                if (lance_probe1( dev, &lance_addr_list[i] )) {

                        found = 1;

                        return( 0 );

                }

        }

        return( ENODEV );

}

/* Derived from hwreg_present() in atari/config.c: */

static int addr_accessible( volatile void *regp, int wordflag, int writeflag )

{       int             ret;

        long    flags;

        long    *vbr, save_berr;

        save_flags(flags);

        cli();

        __asm__ __volatile__ ( "movec   %/vbr,%0" : "=r" (vbr) : );

        save_berr = vbr[2];

        __asm__ __volatile__

        (       "movel  %/sp,%/d1\n\t"

                "movel  #Lberr,%2@\n\t"

                "moveq  #0,%0\n\t"

                "tstl   %3\n\t"

                "bne    1f\n\t"

                "moveb  %1@,%/d0\n\t"

                "nop    \n\t"

                "bra    2f\n"

"1:              movew  %1@,%/d0\n\t"

                "nop    \n"

"2:              tstl   %4\n\t"

                "beq    2f\n\t"

                "tstl   %3\n\t"

                "bne    1f\n\t"

                "clrb   %1@\n\t"

                "nop    \n\t"

                "moveb  %/d0,%1@\n\t"

                "nop    \n\t"

                "bra    2f\n"

"1:              clrw   %1@\n\t"

                "nop    \n\t"

                "movew  %/d0,%1@\n\t"

                "nop    \n"

"2:              moveq  #1,%0\n"

"Lberr:  movel  %/d1,%/sp"

                : "=&d" (ret)

                : "a" (regp), "a" (&vbr[2]), "rm" (wordflag), "rm" (writeflag)

                : "d0", "d1", "memory"

        );

        vbr[2] = save_berr;

        restore_flags(flags);

        return( ret );

}

static unsigned long lance_probe1( struct device *dev,

                                                                   struct lance_addr *init_rec )

{       volatile unsigned short *memaddr =

                (volatile unsigned short *)init_rec->memaddr;

        volatile unsigned short *ioaddr =

                (volatile unsigned short *)init_rec->ioaddr;

        struct lance_private    *lp;

        struct lance_ioreg              *IO;

        int                                     i;

        static int                              did_version = 0;

        unsigned short                  save1, save2;

        PROBE_PRINT(( "Probing for Lance card at mem %#lx io %#lx\n",

                                  (long)memaddr, (long)ioaddr ));

        /* Test whether memory readable and writable */

        PROBE_PRINT(( "lance_probe1: testing memory to be accessible\n" ));

        if (!addr_accessible( memaddr, 1, 1 )) goto probe_fail;

        /* Written values should come back... */

        PROBE_PRINT(( "lance_probe1: testing memory to be writable (1)\n" ));

        save1 = *memaddr;

        *memaddr = 0x0001;

        if (*memaddr != 0x0001) goto probe_fail;

        PROBE_PRINT(( "lance_probe1: testing memory to be writable (2)\n" ));

        *memaddr = 0x0000;

        if (*memaddr != 0x0000) goto probe_fail;

        *memaddr = save1;

        /* First port should be readable and writable */

        PROBE_PRINT(( "lance_probe1: testing ioport to be accessible\n" ));

        if (!addr_accessible( ioaddr, 1, 1 )) goto probe_fail;

        /* and written values should be readable */

        PROBE_PRINT(( "lance_probe1: testing ioport to be writeable\n" ));

        save2 = ioaddr[1];

        ioaddr[1] = 0x0001;

        if (ioaddr[1] != 0x0001) goto probe_fail;

        /* The CSR0_INIT bit should not be readable */

        PROBE_PRINT(( "lance_probe1: testing CSR0 register function (1)\n" ));

        save1 = ioaddr[0];

        ioaddr[1] = CSR0;

        ioaddr[0] = CSR0_INIT | CSR0_STOP;

        if (ioaddr[0] != CSR0_STOP) {

                ioaddr[0] = save1;

                ioaddr[1] = save2;

                goto probe_fail;

        }

        PROBE_PRINT(( "lance_probe1: testing CSR0 register function (2)\n" ));

        ioaddr[0] = CSR0_STOP;

        if (ioaddr[0] != CSR0_STOP) {

                ioaddr[0] = save1;

                ioaddr[1] = save2;

                goto probe_fail;

        }

        /* Now ok... */

        PROBE_PRINT(( "lance_probe1: Lance card detected\n" ));

        goto probe_ok;

  probe_fail:

        return( 0 );

  probe_ok:

        init_etherdev( dev, sizeof(struct lance_private) );

        if (!dev->priv)

                dev->priv = kmalloc( sizeof(struct lance_private), GFP_KERNEL );

        lp = (struct lance_private *)dev->priv;

        MEM = (struct lance_memory *)memaddr;

        IO = lp->iobase = (struct lance_ioreg *)ioaddr;

        dev->base_addr = (unsigned long)ioaddr; /* informational only */

        lp->memcpy_f = init_rec->slow_flag ? slow_memcpy : memcpy;

        REGA( CSR0 ) = CSR0_STOP;

        /* Now test for type: If the eeprom I/O port is readable, it is a

         * PAM card */

        if (addr_accessible( &(IO->eeprom), 0, 0 )) {

                /* Switch back to Ram */

                i = IO->mem;

                lp->cardtype = PAM_CARD;

        }

        else if (*RIEBL_MAGIC_ADDR == RIEBL_MAGIC) {

                lp->cardtype = NEW_RIEBL;

        }

        else

                lp->cardtype = OLD_RIEBL;

        if (lp->cardtype == PAM_CARD ||

                memaddr == (unsigned short *)0xffe00000) {

                /* PAMs card and Riebl on ST use level 5 autovector */

                add_isr( IRQ_AUTO_5, (isrfunc)lance_interrupt, IRQ_TYPE_PRIO, dev,

                                 "PAM/Riebl-ST Ethernet" );

                dev->irq = (unsigned short)IRQ_AUTO_5;

        }

        else {

                /* For VME-RieblCards, request a free VME int;

                 * (This must be unsigned long, since dev->irq is short and the

                 * IRQ_MACHSPEC bit would be cut off...)

                 */

                unsigned long irq = atari_register_vme_int();

                if (!irq) {

                        printk( "Lance: request for VME interrupt failed\n" );

                        return( 0 );

                }

                add_isr( irq, (isrfunc)lance_interrupt, IRQ_TYPE_PRIO, dev,

                                 "Riebl-VME Ethernet" );

                dev->irq = irq;

        }

        printk("%s: %s at io %#lx, mem %#lx, irq %d%s, hwaddr ",

                   dev->name, lance_names[lp->cardtype],

                   (unsigned long)ioaddr,

                   (unsigned long)memaddr,

                   dev->irq,

                   init_rec->slow_flag ? " (slow memcpy)" : "" );

        /* Get the ethernet address */

        switch( lp->cardtype ) {

          case OLD_RIEBL:

                /* No ethernet address! (Set some default address) */

                memcpy( dev->dev_addr, OldRieblDefHwaddr, 6 );

                break;

          case NEW_RIEBL:

                lp->memcpy_f( dev->dev_addr, RIEBL_HWADDR_ADDR, 6 );

                break;

          case PAM_CARD:

                i = IO->eeprom;

                for( i = 0; i < 6; ++i )

                        dev->dev_addr[i] =

                                ((((unsigned short *)MEM)[i*2] & 0x0f) << 4) |

                                ((((unsigned short *)MEM)[i*2+1] & 0x0f));

                i = IO->mem;

                break;

        }

        for( i = 0; i < 6; ++i )

                printk( "%02x%s", dev->dev_addr[i], (i < 5) ? ":" : "\n" );

        if (lp->cardtype == OLD_RIEBL) {

                printk( "%s: Warning: This is a default ethernet address!\n",

                                dev->name );

                printk( "      Use \"ifconfig hw ether ...\" to set the address.\n" );

        }

        MEM->init.mode = 0x0000;                /* Disable Rx and Tx. */

        for( i = 0; i < 6; i++ )

                MEM->init.hwaddr[i] = dev->dev_addr[i^1]; /* <- 16 bit swap! */

        MEM->init.filter[0] = 0x00000000;

        MEM->init.filter[1] = 0x00000000;

        MEM->init.rx_ring.adr_lo = offsetof( struct lance_memory, rx_head );

        MEM->init.rx_ring.adr_hi = 0;

        MEM->init.rx_ring.len    = RX_RING_LEN_BITS;

        MEM->init.tx_ring.adr_lo = offsetof( struct lance_memory, tx_head );

        MEM->init.tx_ring.adr_hi = 0;

        MEM->init.tx_ring.len    = TX_RING_LEN_BITS;

        if (lp->cardtype == PAM_CARD)

                IO->ivec = IRQ_SOURCE_TO_VECTOR(dev->irq);

        else

                *RIEBL_IVEC_ADDR = IRQ_SOURCE_TO_VECTOR(dev->irq);

        if (did_version++ == 0)

                DPRINTK( 1, ( version ));

        /* The LANCE-specific entries in the device structure. */

        dev->open = &lance_open;

        dev->hard_start_xmit = &lance_start_xmit;

        dev->stop = &lance_close;

        dev->get_stats = &lance_get_stats;

        dev->set_multicast_list = &set_multicast_list;

        dev->set_mac_address = &lance_set_mac_address;

        dev->start = 0;

        memset( &lp->stats, 0, sizeof(lp->stats) );

        return( 1 );

}

static int lance_open( struct device *dev )

{       struct lance_private *lp = (struct lance_private *)dev->priv;

        struct lance_ioreg       *IO = lp->iobase;

        int i;

        DPRINTK( 2, ( "%s: lance_open()\n", dev->name ));

        lance_init_ring(dev);

        /* Re-initialize the LANCE, and start it when done. */

        REGA( CSR3 ) = CSR3_BSWP | (lp->cardtype == PAM_CARD ? CSR3_ACON : 0);

        REGA( CSR2 ) = 0;

        REGA( CSR1 ) = 0;

        REGA( CSR0 ) = CSR0_INIT;

        /* From now on, AREG is kept to point to CSR0 */

        i = 1000000;

        while (--i > 0)

                if (DREG & CSR0_IDON)

                        break;

        if (i < 0 || (DREG & CSR0_ERR)) {

                DPRINTK( 2, ( "lance_open(): opening %s failed, i=%d, csr0=%04x\n",

                                          dev->name, i, DREG ));

                DREG = CSR0_STOP;

                return( -EIO );

        }

        DREG = CSR0_IDON;

        DREG = CSR0_STRT;

        DREG = CSR0_INEA;

        dev->tbusy = 0;

        dev->interrupt = 0;

        dev->start = 1;

        DPRINTK( 2, ( "%s: LANCE is open, csr0 %04x\n", dev->name, DREG ));

        MOD_INC_USE_COUNT;

        return( 0 );

}

/* Initialize the LANCE Rx and Tx rings. */

static void lance_init_ring( struct device *dev )

{       struct lance_private *lp = (struct lance_private *)dev->priv;

        int i;

        unsigned offset;

        lp->lock = 0;

        lp->tx_full = 0;

        lp->cur_rx = lp->cur_tx = 0;

        lp->dirty_tx = 0;

        offset = offsetof( struct lance_memory, packet_area );

/* If the packet buffer at offset 'o' would conflict with the reserved area

 * of RieblCards, advance it */

#define CHECK_OFFSET(o)                                                                                                          \

        do {                                                                                                                                     \

                if (lp->cardtype == OLD_RIEBL || lp->cardtype == NEW_RIEBL) {            \