Subversion Repositories or1k

/*

 * eth82586.h: Intel EtherExpress defines

 *

 * Written 1995 by John Sullivan

 * See eexpress.c for further details

 * documentation and usage to do.

 */

/*

 * EtherExpress card register addresses

 * as offsets from the base IO region (dev->base_addr)

 */

#define DATAPORT 0x0000

#define WRITE_PTR 0x0002

#define READ_PTR 0x0004

#define SIGNAL_CA 0x0006

#define SET_IRQ 0x0007

#define SM_PTR 0x0008

#define MEM_Ctrl 0x000b

#define MEM_Page_Ctrl 0x000c

#define Config 0x000d

#define EEPROM_Ctrl 0x000e

#define ID_PORT 0x000f

/*

 * offset to shadowed memory, 0 <= x <= 31. We don't use this yet,

 * but may in the future. Is shadow memory access any faster than

 * dataport access?

 */

#define SM_ADDR(x) (0x4000+((x&0x10)<<10)+(x&0xf))

/* Always mirrors eexp-memory at 0x0008-0x000f */

#define SCB_STATUS 0xc008

#define SCB_CMD 0xc00a

#define SCB_CBL 0xc00c

#define SCB_RFA 0xc00e

/*

 * card register defines

 */

/* SET_IRQ */

#define SIRQ_en 0x08

#define SIRQ_dis 0x00

/* Config */

#define set_loopback outb(inb(ioaddr+Config)|0x02,ioaddr+Config)

#define clear_loopback outb(inb(ioaddr+Config)&0xfd,ioaddr+Config)

/* EEPROM_Ctrl */

#define EC_Clk 0x01

#define EC_CS  0x02

#define EC_Wr  0x04

#define EC_Rd  0x08

#define ASIC_RST 0x40

#define i586_RST  0x80

#define eeprom_delay() { int _i = 40; while (--_i>0) { __SLOW_DOWN_IO; }}

/*

 * i82586 Memory Configuration

 */

/* (System Configuration Pointer) System start up block, read after 586_RST */

#define SCP_START 0xfff6

/* Intermediate System Configuration Pointer */

#define ISCP_START 0x0000

/* System Command Block */

#define SCB_START 0x0008

/*

 * Start of buffer region. If we have 64k memory, eexp_hw_probe() may raise

 * NUM_TX_BUFS. RX_BUF_END is set to the end of memory, and all space between

 * the transmit buffer region and end of memory used for as many receive buffers

 * as we can fit. See eexp_hw_[(rx)(tx)]init().

 */

#define TX_BUF_START 0x0100

#define TX_BUF_SIZE ((24+ETH_FRAME_LEN+31)&~0x1f)

#define RX_BUF_SIZE ((32+ETH_FRAME_LEN+31)&~0x1f)

/*

 * SCB defines

 */

/* these functions take the SCB status word and test the relevant status bit */

#define SCB_complete(s) ((s&0x8000)!=0)

#define SCB_rxdframe(s) ((s&0x4000)!=0)

#define SCB_CUdead(s) ((s&0x2000)!=0)

#define SCB_RUdead(s) ((s&0x1000)!=0)

#define SCB_ack(s) (s & 0xf000)

/* Command unit status: 0=idle, 1=suspended, 2=active */

#define SCB_CUstat(s) ((s&0x0300)>>8)

/* Receive unit status: 0=idle, 1=suspended, 2=out of resources, 4=ready */

#define SCB_RUstat(s) ((s&0x0070)>>4)

/* SCB commands */

#define SCB_CUnop     0x0000

#define SCB_CUstart   0x0100

#define SCB_CUresume  0x0200

#define SCB_CUsuspend 0x0300

#define SCB_CUabort   0x0400

/* ? */

#define SCB_resetchip 0x0080

#define SCB_RUnop     0x0000

#define SCB_RUstart   0x0010

#define SCB_RUresume  0x0020

#define SCB_RUsuspend 0x0030

#define SCB_RUabort   0x0040

/*

 * Command block defines

 */

#define Stat_Done(s)   ((s&0x8000)!=0)

#define Stat_Busy(s)   ((s&0x4000)!=0)

#define Stat_OK(s)     ((s&0x2000)!=0)

#define Stat_Abort(s)  ((s&0x1000)!=0)

#define Stat_STFail    ((s&0x0800)!=0)

#define Stat_TNoCar(s) ((s&0x0400)!=0)

#define Stat_TNoCTS(s) ((s&0x0200)!=0)

#define Stat_TNoDMA(s) ((s&0x0100)!=0)

#define Stat_TDefer(s) ((s&0x0080)!=0)

#define Stat_TColl(s)  ((s&0x0040)!=0)

#define Stat_TXColl(s) ((s&0x0020)!=0)

#define Stat_NoColl(s) (s&0x000f)

/* Cmd_END will end AFTER the command if this is the first

 * command block after an SCB_CUstart, but BEFORE the command

 * for all subsequent commands. Best strategy is to place

 * Cmd_INT on the last command in the sequence, followed by a

 * dummy Cmd_Nop with Cmd_END after this.

 */

#define Cmd_END     0x8000

#define Cmd_SUS     0x4000

#define Cmd_INT     0x2000

#define Cmd_Nop     0x0000

#define Cmd_SetAddr 0x0001

#define Cmd_Config  0x0002

#define Cmd_MCast   0x0003

#define Cmd_Xmit    0x0004

#define Cmd_TDR     0x0005

#define Cmd_Dump    0x0006

#define Cmd_Diag    0x0007

/*

 * Frame Descriptor (Receive block) defines

 */

#define FD_Done(s)  ((s&0x8000)!=0)

#define FD_Busy(s)  ((s&0x4000)!=0)

#define FD_OK(s)    ((s&0x2000)!=0)

#define FD_CRC(s)   ((s&0x0800)!=0)

#define FD_Align(s) ((s&0x0400)!=0)

#define FD_Resrc(s) ((s&0x0200)!=0)

#define FD_DMA(s)   ((s&0x0100)!=0)

#define FD_Short(s) ((s&0x0080)!=0)

#define FD_NoEOF(s) ((s&0x0040)!=0)