Subversion Repositories or1k

/*

 * defines, etc for the seeq8005

 */

/*

 * This file is distributed under GPL.

 *

 * This style and layout of this file is also copied

 * from many of the other linux network device drivers.

 */

/* The number of low I/O ports used by the ethercard. */

#define SEEQ8005_IO_EXTENT      16

#define SEEQ_B          (ioaddr)

#define SEEQ_CMD        (SEEQ_B)                /* Write only */

#define SEEQ_STATUS     (SEEQ_B)                /* Read only */

#define SEEQ_CFG1       (SEEQ_B + 2)

#define SEEQ_CFG2       (SEEQ_B + 4)

#define SEEQ_REA        (SEEQ_B + 6)            /* Receive End Area Register */

#define SEEQ_RPR        (SEEQ_B + 10)           /* Receive Pointer Register */

#define SEEQ_TPR        (SEEQ_B + 12)           /* Transmit Pointer Register */

#define SEEQ_DMAAR      (SEEQ_B + 14)           /* DMA Address Register */

#define SEEQ_BUFFER     (SEEQ_B + 8)            /* Buffer Window Register */

#define DEFAULT_TEA     (0x3f)

#define SEEQCMD_DMA_INT_EN      (0x0001)        /* DMA Interrupt Enable */

#define SEEQCMD_RX_INT_EN       (0x0002)        /* Receive Interrupt Enable */

#define SEEQCMD_TX_INT_EN       (0x0004)        /* Transmit Interrupt Enable */

#define SEEQCMD_WINDOW_INT_EN   (0x0008)        /* What the hell is this for?? */

#define SEEQCMD_INT_MASK        (0x000f)

#define SEEQCMD_DMA_INT_ACK     (0x0010)        /* DMA ack */

#define SEEQCMD_RX_INT_ACK      (0x0020)

#define SEEQCMD_TX_INT_ACK      (0x0040)

#define SEEQCMD_WINDOW_INT_ACK  (0x0080)

#define SEEQCMD_ACK_ALL         (0x00f0)

#define SEEQCMD_SET_DMA_ON      (0x0100)        /* Enables DMA Request logic */

#define SEEQCMD_SET_RX_ON       (0x0200)        /* Enables Packet RX */

#define SEEQCMD_SET_TX_ON       (0x0400)        /* Starts TX run */

#define SEEQCMD_SET_DMA_OFF     (0x0800)

#define SEEQCMD_SET_RX_OFF      (0x1000)

#define SEEQCMD_SET_TX_OFF      (0x2000)

#define SEEQCMD_SET_ALL_OFF     (0x3800)        /* set all logic off */

#define SEEQCMD_FIFO_READ       (0x4000)        /* Set FIFO to read mode (read from Buffer) */

#define SEEQCMD_FIFO_WRITE      (0x8000)        /* Set FIFO to write mode */

#define SEEQSTAT_DMA_INT_EN     (0x0001)        /* Status of interrupt enable */

#define SEEQSTAT_RX_INT_EN      (0x0002)

#define SEEQSTAT_TX_INT_EN      (0x0004)

#define SEEQSTAT_WINDOW_INT_EN  (0x0008)

#define SEEQSTAT_DMA_INT        (0x0010)        /* Interrupt flagged */

#define SEEQSTAT_RX_INT         (0x0020)

#define SEEQSTAT_TX_INT         (0x0040)

#define SEEQSTAT_WINDOW_INT     (0x0080)

#define SEEQSTAT_ANY_INT        (0x00f0)

#define SEEQSTAT_DMA_ON         (0x0100)        /* DMA logic on */

#define SEEQSTAT_RX_ON          (0x0200)        /* Packet RX on */

#define SEEQSTAT_TX_ON          (0x0400)        /* TX running */

#define SEEQSTAT_FIFO_FULL      (0x2000)

#define SEEQSTAT_FIFO_EMPTY     (0x4000)

#define SEEQSTAT_FIFO_DIR       (0x8000)        /* 1=read, 0=write */

#define SEEQCFG1_BUFFER_MASK    (0x000f)        /* define what maps into the BUFFER register */

#define SEEQCFG1_BUFFER_MAC0    (0x0000)        /* MAC station addresses 0-5 */

#define SEEQCFG1_BUFFER_MAC1    (0x0001)

#define SEEQCFG1_BUFFER_MAC2    (0x0002)

#define SEEQCFG1_BUFFER_MAC3    (0x0003)

#define SEEQCFG1_BUFFER_MAC4    (0x0004)

#define SEEQCFG1_BUFFER_MAC5    (0x0005)

#define SEEQCFG1_BUFFER_PROM    (0x0006)        /* The Address/CFG PROM */

#define SEEQCFG1_BUFFER_TEA     (0x0007)        /* Transmit end area */

#define SEEQCFG1_BUFFER_BUFFER  (0x0008)        /* Packet buffer memory */

#define SEEQCFG1_BUFFER_INT_VEC (0x0009)        /* Interrupt Vector */

#define SEEQCFG1_DMA_INTVL_MASK (0x0030)

#define SEEQCFG1_DMA_CONT       (0x0000)

#define SEEQCFG1_DMA_800ns      (0x0010)

#define SEEQCFG1_DMA_1600ns     (0x0020)

#define SEEQCFG1_DMA_3200ns     (0x0030)

#define SEEQCFG1_DMA_LEN_MASK   (0x00c0)

#define SEEQCFG1_DMA_LEN1       (0x0000)

#define SEEQCFG1_DMA_LEN2       (0x0040)

#define SEEQCFG1_DMA_LEN4       (0x0080)

#define SEEQCFG1_DMA_LEN8       (0x00c0)

#define SEEQCFG1_MAC_MASK       (0x3f00)        /* Dis/enable bits for MAC addresses */

#define SEEQCFG1_MAC0_EN        (0x0100)

#define SEEQCFG1_MAC1_EN        (0x0200)

#define SEEQCFG1_MAC2_EN        (0x0400)

#define SEEQCFG1_MAC3_EN        (0x0800)

#define SEEQCFG1_MAC4_EN        (0x1000)

#define SEEQCFG1_MAC5_EN        (0x2000)

#define SEEQCFG1_MATCH_MASK     (0xc000)        /* Packet matching logic cfg bits */

#define SEEQCFG1_MATCH_SPECIFIC (0x0000)        /* only matching MAC addresses */

#define SEEQCFG1_MATCH_BROAD    (0x4000)        /* matching and broadcast addresses */

#define SEEQCFG1_MATCH_MULTI    (0x8000)        /* matching, broadcast and multicast */

#define SEEQCFG1_MATCH_ALL      (0xc000)        /* Promiscuous mode */

#define SEEQCFG1_DEFAULT        (SEEQCFG1_BUFFER_BUFFER | SEEQCFG1_MAC0_EN | SEEQCFG1_MATCH_BROAD)

#define SEEQCFG2_BYTE_SWAP      (0x0001)        /* 0=Intel byte-order */

#define SEEQCFG2_AUTO_REA       (0x0002)        /* if set, Receive End Area will be updated when reading from Buffer */

#define SEEQCFG2_CRC_ERR_EN     (0x0008)        /* enables receiving of packets with CRC errors */

#define SEEQCFG2_DRIBBLE_EN     (0x0010)        /* enables receiving of non-aligned packets */

#define SEEQCFG2_SHORT_EN       (0x0020)        /* enables receiving of short packets */

#define SEEQCFG2_SLOTSEL        (0x0040)        /* 0= standard IEEE802.3, 1= smaller,faster, non-standard */

#define SEEQCFG2_NO_PREAM       (0x0080)        /* 1= user supplies Xmit preamble bytes */

#define SEEQCFG2_ADDR_LEN       (0x0100)        /* 1= 2byte addresses */

#define SEEQCFG2_REC_CRC        (0x0200)        /* 0= received packets will have CRC stripped from them */

#define SEEQCFG2_XMIT_NO_CRC    (0x0400)        /* don't xmit CRC with each packet (user supplies it) */

#define SEEQCFG2_LOOPBACK       (0x0800)

#define SEEQCFG2_CTRLO          (0x1000)

#define SEEQCFG2_RESET          (0x8000)        /* software Hard-reset bit */

struct seeq_pkt_hdr {

        unsigned short  next;                   /* address of next packet header */

        unsigned char   babble_int:1,           /* enable int on >1514 byte packet */

                        coll_int:1,             /* enable int on collision */

                        coll_16_int:1,          /* enable int on >15 collision */

                        xmit_int:1,             /* enable int on success (or xmit with <15 collision) */

                        unused:1,

                        data_follows:1,         /* if not set, process this as a header and pointer only */

                        chain_cont:1,           /* if set, more headers in chain                only cmd bit valid in recv header */

                        xmit_recv:1;            /* if set, a xmit packet, else a receive packet.*/

        unsigned char   status;

};

#define SEEQPKTH_BAB_INT_EN     (0x01)          /* xmit only */

#define SEEQPKTH_COL_INT_EN     (0x02)          /* xmit only */

#define SEEQPKTH_COL16_INT_EN   (0x04)          /* xmit only */

#define SEEQPKTH_XMIT_INT_EN    (0x08)          /* xmit only */

#define SEEQPKTH_DATA_FOLLOWS   (0x20)          /* supposedly in xmit only */

#define SEEQPKTH_CHAIN          (0x40)          /* more headers follow */

#define SEEQPKTH_XMIT           (0x80)

#define SEEQPKTS_BABBLE         (0x0100)        /* xmit only */

#define SEEQPKTS_OVERSIZE       (0x0100)        /* recv only */

#define SEEQPKTS_COLLISION      (0x0200)        /* xmit only */

#define SEEQPKTS_CRC_ERR        (0x0200)        /* recv only */

#define SEEQPKTS_COLL16         (0x0400)        /* xmit only */

#define SEEQPKTS_DRIB           (0x0400)        /* recv only */

#define SEEQPKTS_SHORT          (0x0800)        /* recv only */

#define SEEQPKTS_DONE           (0x8000)

#define SEEQPKTS_ANY_ERROR      (0x0f00)