OpenCores
URL https://opencores.org/ocsvn/or1k/or1k/trunk

Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [net/] [z8530.h] - Blame information for rev 1626

Go to most recent revision | Details | Compare with Previous | View Log

Line No. Rev Author Line
1 1626 jcastillo
 
2
/* 8530 Serial Communications Controller Register definitions */
3
#define FLAG    0x7e
4
 
5
/* Write Register 0 */
6
#define R0      0                /* Register selects */
7
#define R1      1
8
#define R2      2
9
#define R3      3
10
#define R4      4
11
#define R5      5
12
#define R6      6
13
#define R7      7
14
#define R8      8
15
#define R9      9
16
#define R10     10
17
#define R11     11
18
#define R12     12
19
#define R13     13
20
#define R14     14
21
#define R15     15
22
 
23
#define NULLCODE        0        /* Null Code */
24
#define POINT_HIGH      0x8     /* Select upper half of registers */
25
#define RES_EXT_INT     0x10    /* Reset Ext. Status Interrupts */
26
#define SEND_ABORT      0x18    /* HDLC Abort */
27
#define RES_RxINT_FC    0x20    /* Reset RxINT on First Character */
28
#define RES_Tx_P        0x28    /* Reset TxINT Pending */
29
#define ERR_RES         0x30    /* Error Reset */
30
#define RES_H_IUS       0x38    /* Reset highest IUS */
31
 
32
#define RES_Rx_CRC      0x40    /* Reset Rx CRC Checker */
33
#define RES_Tx_CRC      0x80    /* Reset Tx CRC Checker */
34
#define RES_EOM_L       0xC0    /* Reset EOM latch */
35
 
36
/* Write Register 1 */
37
 
38
#define EXT_INT_ENAB    0x1     /* Ext Int Enable */
39
#define TxINT_ENAB      0x2     /* Tx Int Enable */
40
#define PAR_SPEC        0x4     /* Parity is special condition */
41
 
42
#define RxINT_DISAB     0        /* Rx Int Disable */
43
#define RxINT_FCERR     0x8     /* Rx Int on First Character Only or Error */
44
#define INT_ALL_Rx      0x10    /* Int on all Rx Characters or error */
45
#define INT_ERR_Rx      0x18    /* Int on error only */
46
 
47
#define WT_RDY_RT       0x20    /* Wait/Ready on R/T */
48
#define WT_FN_RDYFN     0x40    /* Wait/FN/Ready FN */
49
#define WT_RDY_ENAB     0x80    /* Wait/Ready Enable */
50
 
51
/* Write Register #2 (Interrupt Vector) */
52
 
53
/* Write Register 3 */
54
 
55
#define RxENABLE        0x1     /* Rx Enable */
56
#define SYNC_L_INH      0x2     /* Sync Character Load Inhibit */
57
#define ADD_SM          0x4     /* Address Search Mode (SDLC) */
58
#define RxCRC_ENAB      0x8     /* Rx CRC Enable */
59
#define ENT_HM          0x10    /* Enter Hunt Mode */
60
#define AUTO_ENAB       0x20    /* Auto Enables */
61
#define Rx5             0x0     /* Rx 5 Bits/Character */
62
#define Rx7             0x40    /* Rx 7 Bits/Character */
63
#define Rx6             0x80    /* Rx 6 Bits/Character */
64
#define Rx8             0xc0    /* Rx 8 Bits/Character */
65
 
66
/* Write Register 4 */
67
 
68
#define PAR_ENA         0x1     /* Parity Enable */
69
#define PAR_EVEN        0x2     /* Parity Even/Odd* */
70
 
71
#define SYNC_ENAB       0        /* Sync Modes Enable */
72
#define SB1             0x4     /* 1 stop bit/char */
73
#define SB15            0x8     /* 1.5 stop bits/char */
74
#define SB2             0xc     /* 2 stop bits/char */
75
 
76
#define MONSYNC         0        /* 8 Bit Sync character */
77
#define BISYNC          0x10    /* 16 bit sync character */
78
#define SDLC            0x20    /* SDLC Mode (01111110 Sync Flag) */
79
#define EXTSYNC         0x30    /* External Sync Mode */
80
 
81
#define X1CLK           0x0     /* x1 clock mode */
82
#define X16CLK          0x40    /* x16 clock mode */
83
#define X32CLK          0x80    /* x32 clock mode */
84
#define X64CLK          0xC0    /* x64 clock mode */
85
 
86
/* Write Register 5 */
87
 
88
#define TxCRC_ENAB      0x1     /* Tx CRC Enable */
89
#define RTS             0x2     /* RTS */
90
#define SDLC_CRC        0x4     /* SDLC/CRC-16 */
91
#define TxENAB          0x8     /* Tx Enable */
92
#define SND_BRK         0x10    /* Send Break */
93
#define Tx5             0x0     /* Tx 5 bits (or less)/character */
94
#define Tx7             0x20    /* Tx 7 bits/character */
95
#define Tx6             0x40    /* Tx 6 bits/character */
96
#define Tx8             0x60    /* Tx 8 bits/character */
97
#define DTR             0x80    /* DTR */
98
 
99
/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
100
 
101
/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
102
 
103
/* Write Register 8 (transmit buffer) */
104
 
105
/* Write Register 9 (Master interrupt control) */
106
#define VIS     1       /* Vector Includes Status */
107
#define NV      2       /* No Vector */
108
#define DLC     4       /* Disable Lower Chain */
109
#define MIE     8       /* Master Interrupt Enable */
110
#define STATHI  0x10    /* Status high */
111
#define NORESET 0        /* No reset on write to R9 */
112
#define CHRB    0x40    /* Reset channel B */
113
#define CHRA    0x80    /* Reset channel A */
114
#define FHWRES  0xc0    /* Force hardware reset */
115
 
116
/* Write Register 10 (misc control bits) */
117
#define BIT6    1       /* 6 bit/8bit sync */
118
#define LOOPMODE 2      /* SDLC Loop mode */
119
#define ABUNDER 4       /* Abort/flag on SDLC xmit underrun */
120
#define MARKIDLE 8      /* Mark/flag on idle */
121
#define GAOP    0x10    /* Go active on poll */
122
#define NRZ     0        /* NRZ mode */
123
#define NRZI    0x20    /* NRZI mode */
124
#define FM1     0x40    /* FM1 (transition = 1) */
125
#define FM0     0x60    /* FM0 (transition = 0) */
126
#define CRCPS   0x80    /* CRC Preset I/O */
127
 
128
/* Write Register 11 (Clock Mode control) */
129
#define TRxCXT  0        /* TRxC = Xtal output */
130
#define TRxCTC  1       /* TRxC = Transmit clock */
131
#define TRxCBR  2       /* TRxC = BR Generator Output */
132
#define TRxCDP  3       /* TRxC = DPLL output */
133
#define TRxCOI  4       /* TRxC O/I */
134
#define TCRTxCP 0        /* Transmit clock = RTxC pin */
135
#define TCTRxCP 8       /* Transmit clock = TRxC pin */
136
#define TCBR    0x10    /* Transmit clock = BR Generator output */
137
#define TCDPLL  0x18    /* Transmit clock = DPLL output */
138
#define RCRTxCP 0        /* Receive clock = RTxC pin */
139
#define RCTRxCP 0x20    /* Receive clock = TRxC pin */
140
#define RCBR    0x40    /* Receive clock = BR Generator output */
141
#define RCDPLL  0x60    /* Receive clock = DPLL output */
142
#define RTxCX   0x80    /* RTxC Xtal/No Xtal */
143
 
144
/* Write Register 12 (lower byte of baud rate generator time constant) */
145
 
146
/* Write Register 13 (upper byte of baud rate generator time constant) */
147
 
148
/* Write Register 14 (Misc control bits) */
149
#define BRENABL 1       /* Baud rate generator enable */
150
#define BRSRC   2       /* Baud rate generator source */
151
#define DTRREQ  4       /* DTR/Request function */
152
#define AUTOECHO 8      /* Auto Echo */
153
#define LOOPBAK 0x10    /* Local loopback */
154
#define SEARCH  0x20    /* Enter search mode */
155
#define RMC     0x40    /* Reset missing clock */
156
#define DISDPLL 0x60    /* Disable DPLL */
157
#define SSBR    0x80    /* Set DPLL source = BR generator */
158
#define SSRTxC  0xa0    /* Set DPLL source = RTxC */
159
#define SFMM    0xc0    /* Set FM mode */
160
#define SNRZI   0xe0    /* Set NRZI mode */
161
 
162
/* Write Register 15 (external/status interrupt control) */
163
#define ZCIE    2       /* Zero count IE */
164
#define DCDIE   8       /* DCD IE */
165
#define SYNCIE  0x10    /* Sync/hunt IE */
166
#define CTSIE   0x20    /* CTS IE */
167
#define TxUIE   0x40    /* Tx Underrun/EOM IE */
168
#define BRKIE   0x80    /* Break/Abort IE */
169
 
170
 
171
/* Read Register 0 */
172
#define Rx_CH_AV        0x1     /* Rx Character Available */
173
#define ZCOUNT          0x2     /* Zero count */
174
#define Tx_BUF_EMP      0x4     /* Tx Buffer empty */
175
#define DCD             0x8     /* DCD */
176
#define SYNC_HUNT       0x10    /* Sync/hunt */
177
#define CTS             0x20    /* CTS */
178
#define TxEOM           0x40    /* Tx underrun */
179
#define BRK_ABRT        0x80    /* Break/Abort */
180
 
181
/* Read Register 1 */
182
#define ALL_SNT         0x1     /* All sent */
183
/* Residue Data for 8 Rx bits/char programmed */
184
#define RES3            0x8     /* 0/3 */
185
#define RES4            0x4     /* 0/4 */
186
#define RES5            0xc     /* 0/5 */
187
#define RES6            0x2     /* 0/6 */
188
#define RES7            0xa     /* 0/7 */
189
#define RES8            0x6     /* 0/8 */
190
#define RES18           0xe     /* 1/8 */
191
#define RES28           0x0     /* 2/8 */
192
/* Special Rx Condition Interrupts */
193
#define PAR_ERR         0x10    /* Parity error */
194
#define Rx_OVR          0x20    /* Rx Overrun Error */
195
#define CRC_ERR         0x40    /* CRC/Framing Error */
196
#define END_FR          0x80    /* End of Frame (SDLC) */
197
 
198
/* Read Register 2 (channel b only) - Interrupt vector */
199
 
200
/* Read Register 3 (interrupt pending register) ch a only */
201
#define CHBEXT  0x1             /* Channel B Ext/Stat IP */
202
#define CHBTxIP 0x2             /* Channel B Tx IP */
203
#define CHBRxIP 0x4             /* Channel B Rx IP */
204
#define CHAEXT  0x8             /* Channel A Ext/Stat IP */
205
#define CHATxIP 0x10            /* Channel A Tx IP */
206
#define CHARxIP 0x20            /* Channel A Rx IP */
207
 
208
/* Read Register 8 (receive data register) */
209
 
210
/* Read Register 10  (misc status bits) */
211
#define ONLOOP  2               /* On loop */
212
#define LOOPSEND 0x10           /* Loop sending */
213
#define CLK2MIS 0x40            /* Two clocks missing */
214
#define CLK1MIS 0x80            /* One clock missing */
215
 
216
/* Read Register 12 (lower byte of baud rate generator constant) */
217
 
218
/* Read Register 13 (upper byte of baud rate generator constant) */
219
 
220
/* Read Register 15 (value of WR 15) */

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.