URL https://opencores.org/ocsvn/or1k/or1k/trunk
Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [scsi/] [aic7xxx/] [aic7xxx.seq] - Blame information for rev 1626

Go to most recent revision | Details | Compare with Previous | View Log

/*
 * Adaptec 274x/284x/294x device driver firmware for Linux and FreeBSD.
 *
 * Copyright (c) 1994-1998 Justin Gibbs.
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions, and the following disclaimer,
 *    without modification, immediately at the beginning of the file.
 * 2. The name of the author may not be used to endorse or promote products
 *    derived from this software without specific prior written permission.
 *
 * Where this Software is combined with software released under the terms of
 * the GNU Public License (GPL) and the terms of the GPL would require the
 * combined work to also be released under the terms of the GPL, the terms
 * and conditions of this License will apply in addition to those of the
 * GPL with the exception of any terms or conditions of this License that
 * conflict with, or are expressly prohibited by, the GPL.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
 * SUCH DAMAGE.
 *
 *      $Id: aic7xxx.seq,v 1.1 2005-12-20 10:18:04 jcastillo Exp $
 */
 
#include "aic7xxx.reg"
#include "scsi_message.h"
 
/*
 * A few words on the waiting SCB list:
 * After starting the selection hardware, we check for reconnecting targets
 * as well as for our selection to complete just in case the reselection wins
 * bus arbitration.  The problem with this is that we must keep track of the
 * SCB that we've already pulled from the QINFIFO and started the selection
 * on just in case the reselection wins so that we can retry the selection at
 * a later time.  This problem cannot be resolved by holding a single entry
 * in scratch ram since a reconnecting target can request sense and this will
 * create yet another SCB waiting for selection.  The solution used here is to
 * use byte 27 of the SCB as a psuedo-next pointer and to thread a list
 * of SCBs that are awaiting selection.  Since 0-0xfe are valid SCB indexes,
 * SCB_LIST_NULL is 0xff which is out of range.  An entry is also added to
 * this list everytime a request sense occurs or after completing a non-tagged
 * command for which a second SCB has been queued.  The sequencer will
 * automatically consume the entries.
 */
 
reset:
        clr     SCSISIGO;               /* De-assert BSY */
        /* Always allow reselection */
        if ((p->flags & AHC_TARGETMODE) != 0) {
                mvi     SCSISEQ, ENSELI|ENRSELI|ENAUTOATNP;
        } else {
                mvi     SCSISEQ, ENRSELI|ENAUTOATNP;
        }
 
        if ((p->features & AHC_CMD_CHAN) != 0) {
                /* Ensure that no DMA operations are in progress */
                clr     CCSGCTL;
                clr     CCSCBCTL;
        }
 
        call    clear_target_state;
        and     SXFRCTL0, ~SPIOEN;
poll_for_work:
        if ((p->features & AHC_QUEUE_REGS) == 0) {
                mov     A, QINPOS;
        }
poll_for_work_loop:
        if ((p->features & AHC_QUEUE_REGS) == 0) {
                and     SEQCTL, ~PAUSEDIS;
        }
        test    SSTAT0, SELDO|SELDI     jnz selection;
        test    SCSISEQ, ENSELO jnz poll_for_work;
        if ((p->features & AHC_TWIN) != 0) {
                /*
                 * Twin channel devices cannot handle things like SELTO
                 * interrupts on the "background" channel.  So, if we
                 * are selecting, keep polling the current channel util
                 * either a selection or reselection occurs.
                 */
                xor     SBLKCTL,SELBUSB;        /* Toggle to the other bus */
                test    SSTAT0, SELDO|SELDI     jnz selection;
                test    SCSISEQ, ENSELO jnz poll_for_work;
                xor     SBLKCTL,SELBUSB;        /* Toggle back */
        }
        cmp     WAITING_SCBH,SCB_LIST_NULL jne start_waiting;
test_queue:
        /* Has the driver posted any work for us? */
        if ((p->features & AHC_QUEUE_REGS) != 0) {
                test    QOFF_CTLSTA, SCB_AVAIL jz poll_for_work_loop;
                mov     NONE, SNSCB_QOFF;
                inc     QINPOS;
        } else {
                or      SEQCTL, PAUSEDIS;
                cmp     KERNEL_QINPOS, A je poll_for_work_loop;
                inc     QINPOS;
                and     SEQCTL, ~PAUSEDIS;
        }
 
/*
 * We have at least one queued SCB now and we don't have any
 * SCBs in the list of SCBs awaiting selection.  If we have
 * any SCBs available for use, pull the tag from the QINFIFO
 * and get to work on it.
 */
        if ((p->flags & AHC_PAGESCBS) != 0) {
                mov     ALLZEROS        call    get_free_or_disc_scb;
        }
 
dequeue_scb:
        add     A, -1, QINPOS;
        mvi     QINFIFO_OFFSET call fetch_byte;
 
        if ((p->flags & AHC_PAGESCBS) == 0) {
                /* In the non-paging case, the SCBID == hardware SCB index */
                mov     SCBPTR, RETURN_2;
        }
dma_queued_scb:
/*
 * DMA the SCB from host ram into the current SCB location.
 */
        mvi     DMAPARAMS, HDMAEN|DIRECTION|FIFORESET;
        mov     RETURN_2         call dma_scb;
 
start_scb:
        /*
         * Place us on the waiting list in case our selection
         * doesn't win during bus arbitration.
         */
        mov     SCB_NEXT,WAITING_SCBH;
        mov     WAITING_SCBH, SCBPTR;
start_waiting:
        /*
         * Pull the first entry off of the waiting SCB list.
         */
        mov     SCBPTR, WAITING_SCBH;
        call    start_selection;
        jmp     poll_for_work;
 
start_selection:
        if ((p->features & AHC_TWIN) != 0) {
                and     SINDEX,~SELBUSB,SBLKCTL;/* Clear channel select bit */
                and     A,SELBUSB,SCB_TCL;      /* Get new channel bit */
                or      SINDEX,A;
                mov     SBLKCTL,SINDEX;         /* select channel */
        }
initialize_scsiid:
        if ((p->features & AHC_ULTRA2) != 0) {
                and     A, TID, SCB_TCL;        /* Get target ID */
                and     SCSIID_ULTRA2, OID;     /* Clear old target */
                or      SCSIID_ULTRA2, A;
        } else {
                and     A, TID, SCB_TCL;        /* Get target ID */
                and     SCSIID, OID;            /* Clear old target */
                or      SCSIID, A;
        }
        mvi     SCSISEQ, ENSELO|ENAUTOATNO|ENRSELI|ENAUTOATNP ret;
 
/*
 * Initialize Ultra mode setting and clear the SCSI channel.
 * SINDEX should contain any additional bit's the client wants
 * set in SXFRCTL0.
 */
initialize_channel:
        or      A, CLRSTCNT|CLRCHN, SINDEX;
        or      SXFRCTL0, A;
        if ((p->features & AHC_ULTRA) != 0) {
ultra:
                mvi     SINDEX, ULTRA_ENB+1;
                test    SAVED_TCL, 0x80         jnz ultra_2; /* Target ID > 7 */
                dec     SINDEX;
ultra_2:
                mov     FUNCTION1,SAVED_TCL;
                mov     A,FUNCTION1;
                test    SINDIR, A       jz ndx_dtr;
                or      SXFRCTL0, FAST20;
        }
/*
 * Initialize SCSIRATE with the appropriate value for this target.
 * The SCSIRATE settings for each target are stored in an array
 * based at TARG_SCSIRATE.
 */
ndx_dtr:
        shr     A,4,SAVED_TCL;
        if ((p->features & AHC_TWIN) != 0) {
                test    SBLKCTL,SELBUSB jz ndx_dtr_2;
                or      SAVED_TCL, SELBUSB;
                or      A,0x08;                 /* Channel B entries add 8 */
ndx_dtr_2:
        }
 
        if ((p->features & AHC_ULTRA2) != 0) {
                add     SINDEX, TARG_OFFSET, A;
                mov     SCSIOFFSET, SINDIR;
        }
 
        add     SINDEX,TARG_SCSIRATE,A;
        mov     SCSIRATE,SINDIR ret;
 
 
selection:
        test    SSTAT0,SELDO    jnz select_out;
select_in:
        if ((p->flags & AHC_TARGETMODE) != 0) {
                test    SSTAT0, TARGET  jz initiator_reselect;
                /*
                 * We've just been selected.  Assert BSY and
                 * setup the phase for receiving the messages
                 * from the target.
                 */
                mvi     SCSISIGO, P_MESGOUT|BSYO;
                mvi     CLRSINT0, CLRSELDO;
 
                /*
                 * If ATN isn't asserted, go directly to bus free.
                 */
                test    SCSISIGI, ATNI  jz      target_busfree;
 
                /*
                 * Setup the DMA for sending the identify and
                 * command information.
                 */
                mov     A, TMODE_CMDADDR_NEXT;
                mvi     DINDEX, HADDR;
                mvi     TMODE_CMDADDR call set_32byte_addr;
                mvi     DFCNTRL, FIFORESET;
 
                clr     SINDEX;
                /* Watch ATN closely now */
message_loop:
                or      SXFRCTL0, SPIOEN;
                test    SSTAT0, SPIORDY jz .;
                and     SXFRCTL0, ~SPIOEN;
                mov     DINDEX, SCSIDATL;
                mov     DFDAT, DINDEX;
                inc     SINDEX;
 
                /* Message Testing... */
                test    DINDEX, MSG_IDENTIFYFLAG jz . + 2;
                mov     ARG_1, DINDEX;
 
                test    SCSISIGI, ATNI  jnz     message_loop;
                add     A, -4, SINDEX;
                jc      target_cmdphase;
                mvi     DFDAT, SCB_LIST_NULL;   /* Terminate the message list */
 
target_cmdphase:
                add     HCNT[0], 1, A;
                clr     HCNT[1];
                clr     HCNT[2];
                mvi     SCSISIGO, P_COMMAND|BSYO;
                or      SXFRCTL0, SPIOEN;
                test    SSTAT0, SPIORDY jz .;
                mov     A, SCSIDATL;
                mov     DFDAT, A;       /* Store for host */
 
                /*
                 * Determine the number of bytes to read
                 * based on the command group code.  Count is
                 * one less than the total since we've already
                 * fetched the first byte.
                 */
                clr     SINDEX;
                shr     A, CMD_GROUP_CODE_SHIFT;
                add     SEQADDR0, A;
 
                add     SINDEX, CMD_GROUP0_BYTE_DELTA;
                nop;    /* Group 1 and 2 are the same */
                add     SINDEX, CMD_GROUP2_BYTE_DELTA;
                nop;    /* Group 3 is reserved */
                add     SINDEX, CMD_GROUP4_BYTE_DELTA;
                add     SINDEX, CMD_GROUP5_BYTE_DELTA;
                /* Group 6 and 7 are not handled yet */
 
                mov     A, SINDEX;
                add     HCNT[0], A;
 
command_loop:
                test    SSTAT0, SPIORDY jz .;
                cmp     SINDEX, 1 jne . + 2;
                and     SXFRCTL0, ~SPIOEN;      /* Last Byte */
                mov     DFDAT, SCSIDATL;
                dec     SINDEX;
                test    SINDEX, 0xFF jnz command_loop;
 
                or      DFCNTRL, HDMAEN|FIFOFLUSH;
 
                call    dma_finish;
 
                test    ARG_1, MSG_IDENTIFY_DISCFLAG jz selectin_post;
 
                mvi     SCSISIGO, P_MESGIN|BSYO;
 
                or      SXFRCTL0, SPIOEN;
 
                mvi     MSG_DISCONNECT call target_outb;
 
selectin_post:
                inc     TMODE_CMDADDR_NEXT;
                cmp     TMODE_CMDADDR_NEXT, TMODE_NUMCMDS jne . + 2;
                clr     TMODE_CMDADDR_NEXT;
                mvi     QOUTFIFO, SCB_LIST_NULL;
                mvi     INTSTAT,CMDCMPLT;
 
                test    ARG_1, MSG_IDENTIFY_DISCFLAG jnz target_busfree;
 
                /* Busy loop on something then go to data or status phase */
 
target_busfree:
                clr     SCSISIGO;
                jmp     poll_for_work;
 
        }
 
/*
 * Reselection has been initiated by a target. Make a note that we've been
 * reselected, but haven't seen an IDENTIFY message from the target yet.
 */
initiator_reselect:
        mvi     CLRSINT0, CLRSELDI;
        /* XXX test for and handle ONE BIT condition */
        and     SAVED_TCL, SELID_MASK, SELID;
        mvi     CLRSINT1,CLRBUSFREE;
        or      SIMODE1, ENBUSFREE;             /*
                                                 * We aren't expecting a
                                                 * bus free, so interrupt
                                                 * the kernel driver if it
                                                 * happens.
                                                 */
        mvi     SPIOEN call     initialize_channel;
        mvi     MSG_OUT, MSG_NOOP;              /* No message to send */
        jmp     ITloop;
 
/*
 * After the selection, remove this SCB from the "waiting SCB"
 * list.  This is achieved by simply moving our "next" pointer into
 * WAITING_SCBH.  Our next pointer will be set to null the next time this
 * SCB is used, so don't bother with it now.
 */
select_out:
        /* Turn off the selection hardware */
        mvi     SCSISEQ, ENRSELI|ENAUTOATNP;    /*
                                                 * ATN on parity errors
                                                 * for "in" phases
                                                 */
        mvi     CLRSINT0, CLRSELDO;
        mov     SCBPTR, WAITING_SCBH;
        mov     WAITING_SCBH,SCB_NEXT;
        mov     SAVED_TCL, SCB_TCL;
        mvi     CLRSINT1,CLRBUSFREE;
        or      SIMODE1, ENBUSFREE;             /*
                                                 * We aren't expecting a
                                                 * bus free, so interrupt
                                                 * the kernel driver if it
                                                 * happens.
                                                 */
        mvi     SPIOEN call     initialize_channel;
/*
 * As soon as we get a successful selection, the target should go
 * into the message out phase since we have ATN asserted.
 */
        mvi     MSG_OUT, MSG_IDENTIFYFLAG;
        or      SEQ_FLAGS, IDENTIFY_SEEN;
 
/*
 * Main loop for information transfer phases.  Wait for the target
 * to assert REQ before checking MSG, C/D and I/O for the bus phase.
 */
ITloop:
        call    phase_lock;
 
        mov     A, LASTPHASE;
 
        test    A, ~P_DATAIN    jz p_data;
        cmp     A,P_COMMAND     je p_command;
        cmp     A,P_MESGOUT     je p_mesgout;
        cmp     A,P_STATUS      je p_status;
        cmp     A,P_MESGIN      je p_mesgin;
 
        mvi     INTSTAT,BAD_PHASE;      /* unknown phase - signal driver */
        jmp     ITloop;                 /* Try reading the bus again. */
 
await_busfree:
        and     SIMODE1, ~ENBUSFREE;
        call    clear_target_state;
        mov     NONE, SCSIDATL;         /* Ack the last byte */
        and     SXFRCTL0, ~SPIOEN;
        test    SSTAT1,REQINIT|BUSFREE  jz .;
        test    SSTAT1, BUSFREE jnz poll_for_work;
        mvi     INTSTAT, BAD_PHASE;
 
clear_target_state:
        clr     DFCNTRL;                /*
                                         * We assume that the kernel driver
                                         * may reset us at any time, even
                                         * in the middle of a DMA, so clear
                                         * DFCNTRL too.
                                         */
        clr     SCSIRATE;               /*
                                         * We don't know the target we will
                                         * connect to, so default to narrow
                                         * transfers to avoid parity problems.
                                         */
        and     SXFRCTL0, ~(FAST20);
        mvi     LASTPHASE, P_BUSFREE;
        /* clear target specific flags */
        and     SEQ_FLAGS, (WIDE_BUS|TWIN_BUS) ret;
 
/*
 * If we re-enter the data phase after going through another phase, the
 * STCNT may have been cleared, so restore it from the residual field.
 */
data_phase_reinit:
        mvi     DINDEX, STCNT;
        mvi     SCB_RESID_DCNT  call bcopy_3;
        jmp     data_phase_loop;
 
p_data:
        if ((p->features & AHC_ULTRA2) != 0) {
                mvi     DMAPARAMS, PRELOADEN|SCSIEN|HDMAEN;
        } else {
                mvi     DMAPARAMS, WIDEODD|SCSIEN|SDMAEN|HDMAEN|FIFORESET;
        }
        test    LASTPHASE, IOI jnz . + 2;
        or      DMAPARAMS, DIRECTION;
        call    assert;                 /*
                                         * Ensure entering a data
                                         * phase is okay - seen identify, etc.
                                         */
        if ((p->features & AHC_CMD_CHAN) != 0) {
                mvi     CCSGADDR, CCSGADDR_MAX;
        }
        test    SEQ_FLAGS, DPHASE       jnz data_phase_reinit;
 
        /* We have seen a data phase */
        or      SEQ_FLAGS, DPHASE;
 
        /*
         * Initialize the DMA address and counter from the SCB.
         * Also set SG_COUNT and SG_NEXT in memory since we cannot
         * modify the values in the SCB itself until we see a
         * save data pointers message.
         */
        if ((p->features & AHC_CMD_CHAN) != 0) {
                bmov    HADDR, SCB_DATAPTR, 7;
        } else {
                mvi     DINDEX, HADDR;
                mvi     SCB_DATAPTR     call bcopy_7;
        }
 
        if ((p->features & AHC_ULTRA2) == 0) {
                call    set_stcnt_from_hcnt;
        }
 
        mov     SG_COUNT,SCB_SGCOUNT;
 
        mvi     DINDEX, SG_NEXT;
        mvi     SCB_SGPTR       call bcopy_4;
 
data_phase_loop:
/* Guard against overruns */
        test    SG_COUNT, 0xff jnz data_phase_inbounds;
/*
 * Turn on 'Bit Bucket' mode, set the transfer count to
 * 16meg and let the target run until it changes phase.
 * When the transfer completes, notify the host that we
 * had an overrun.
 */
        or      SXFRCTL1,BITBUCKET;
        and     DMAPARAMS, ~(HDMAEN|SDMAEN);
        if ((p->features & AHC_ULTRA2) != 0) {
                bmov    HCNT, ALLONES, 3;
        } else {
                mvi     STCNT[0], 0xFF;
                mvi     STCNT[1], 0xFF;
                mvi     STCNT[2], 0xFF;
        }
data_phase_inbounds:
/* If we are the last SG block, tell the hardware. */
        cmp     SG_COUNT,0x01 jne data_phase_wideodd;
        if ((p->features & AHC_ULTRA2) != 0) {
                or      SG_CACHEPTR, LAST_SEG;
        } else {
                and     DMAPARAMS, ~WIDEODD;
        }
data_phase_wideodd:
        if ((p->features & AHC_ULTRA2) != 0) {
                mov     SINDEX, ALLONES;
                mov     DFCNTRL, DMAPARAMS;
                test    SSTAT0, SDONE jnz .;/* Wait for preload to complete */
data_phase_dma_loop:
                test    SSTAT0, SDONE jnz data_phase_dma_done;
                test    SSTAT1,PHASEMIS jz data_phase_dma_loop; /* ie. underrun */
data_phase_dma_phasemis:
                test    SSTAT0,SDONE    jnz . + 2;
                mov     SINDEX,ALLZEROS;        /* Remeber the phasemiss */
        } else {
                mov     DMAPARAMS  call dma;
        }
 
data_phase_dma_done:
/* Go tell the host about any overruns */
        test    SXFRCTL1,BITBUCKET jnz data_phase_overrun;
 
/* Exit if we had an underrun.  dma clears SINDEX in this case. */
        test    SINDEX,0xff     jz data_phase_finish;
 
/*
 * Advance the scatter-gather pointers if needed
 */
sg_advance:
        dec     SG_COUNT;       /* one less segment to go */
 
        test    SG_COUNT, 0xff  jz data_phase_finish; /* Are we done? */
/*
 * Load a struct scatter and set up the data address and length.
 * If the working value of the SG count is nonzero, then
 * we need to load a new set of values.
 *
 * This, like all DMA's, assumes little-endian host data storage.
 */
sg_load:
        if ((p->features & AHC_CMD_CHAN) != 0) {
                /*
                 * Do we have any prefetch left???
                 */
                cmp     CCSGADDR, CCSGADDR_MAX jne prefetched_segs_avail;
 
                /*
                 * Fetch MIN(CCSGADDR_MAX, (SG_COUNT * 8)) bytes.
                 */
                add     A, -(CCSGRAM_MAXSEGS + 1), SG_COUNT;
                mvi     A, CCSGADDR_MAX;
                jc      . + 2;
                shl     A, 3, SG_COUNT;
                mov     CCHCNT, A;
                bmov    CCHADDR, SG_NEXT, 4;
                mvi     CCSGCTL, CCSGEN|CCSGRESET;
                test    CCSGCTL, CCSGDONE jz .;
                and     CCSGCTL, ~CCSGEN;
                test    CCSGCTL, CCSGEN jnz .;
                mvi     CCSGCTL, CCSGRESET;
prefetched_segs_avail:
                bmov    HADDR, CCSGRAM, 8;
        } else {
                mvi     DINDEX, HADDR;
                mvi     SG_NEXT call bcopy_4;
 
                mvi     HCNT[0],SG_SIZEOF;
                clr     HCNT[1];
                clr     HCNT[2];
 
                or      DFCNTRL, HDMAEN|DIRECTION|FIFORESET;
 
                call    dma_finish;
 
                /*
                 * Copy data from FIFO into SCB data pointer and data count.
                 * This assumes that the SG segments are of the form:
                 * struct ahc_dma_seg {
                 *      u_int32_t       addr;   four bytes, little-endian order
                 *      u_int32_t       len;    four bytes, little endian order
                 * };
                 */
                mvi     HADDR   call dfdat_in_7;
        }
 
        if ((p->features & AHC_ULTRA2) == 0) {
                /* Load STCNT as well.  It is a mirror of HCNT */
                call    set_stcnt_from_hcnt;
        }
 
/* Advance the SG pointer */
        clr     A;                      /* add sizeof(struct scatter) */
        add     SG_NEXT[0],SG_SIZEOF;
        adc     SG_NEXT[1],A;
 
        test    SSTAT1,PHASEMIS jz data_phase_loop;
        /* Ensure the last seg is visable at the shaddow layer */
        if ((p->features & AHC_ULTRA2) != 0) {
                or      DFCNTRL, PRELOADEN;
        }
 
data_phase_finish:
        if ((p->features & AHC_ULTRA2) != 0) {
                call    ultra2_dmafinish;
        }
/*
 * After a DMA finishes, save the SG and STCNT residuals back into the SCB
 * We use STCNT instead of HCNT, since it's a reflection of how many bytes
 * were transferred on the SCSI (as opposed to the host) bus.
 */
        mov     SCB_RESID_DCNT[0],STCNT[0];
        mov     SCB_RESID_DCNT[1],STCNT[1];
        mov     SCB_RESID_DCNT[2],STCNT[2];
        mov     SCB_RESID_SGCNT, SG_COUNT;
 
        if ((p->features & AHC_ULTRA2) != 0) {
                or      SXFRCTL0, CLRSTCNT|CLRCHN;
        }
 
        jmp     ITloop;
 
data_phase_overrun:
        if ((p->features & AHC_ULTRA2) != 0) {
                call    ultra2_dmafinish;
                or      SXFRCTL0, CLRSTCNT|CLRCHN;
        }
/*
 * Turn off BITBUCKET mode and notify the host
 */
        and     SXFRCTL1, ~BITBUCKET;
        mvi     INTSTAT,DATA_OVERRUN;
        jmp     ITloop;
 
ultra2_dmafinish:
        if ((p->features & AHC_ULTRA2) != 0) {
                test    DFCNTRL, DIRECTION jnz ultra2_dmahalt;
                and     DFCNTRL, ~SCSIEN;
                test    DFCNTRL, SCSIEN jnz .;
                or      DFCNTRL, FIFOFLUSH;
                test    DFSTATUS, FIFOEMP jz . - 1;
ultra2_dmahalt:
                and     DFCNTRL, ~(SCSIEN|HDMAEN);
                test    DFCNTRL, HDMAEN jnz .;
                ret;
        }
 
/*
 * Command phase.  Set up the DMA registers and let 'er rip.
 */
p_command:
        call    assert;
 
/*
 * Load HADDR and HCNT.
 */
        if ((p->features & AHC_ULTRA2) != 0) {
                or      SG_CACHEPTR, LAST_SEG;
        }
 
        if ((p->features & AHC_CMD_CHAN) != 0) {
                bmov    HADDR, SCB_CMDPTR, 5;
                bmov    HCNT[1], ALLZEROS, 2;
        } else {
                mvi     DINDEX, HADDR;
                mvi     SCB_CMDPTR      call bcopy_5;
                clr     HCNT[1];
                clr     HCNT[2];
        }
 
        if ((p->features & AHC_ULTRA2) == 0) {
                call    set_stcnt_from_hcnt;
                mvi     (SCSIEN|SDMAEN|HDMAEN|DIRECTION|FIFORESET) call dma;
        } else {
                mvi     (PRELOADEN|SCSIEN|HDMAEN|DIRECTION) call dma;
        }
        jmp     ITloop;
 
/*
 * Status phase.  Wait for the data byte to appear, then read it
 * and store it into the SCB.
 */
p_status:
        call    assert;
 
        mov     SCB_TARGET_STATUS, SCSIDATL;
        jmp     ITloop;
 
/*
 * Message out phase.  If MSG_OUT is 0x80, build I full indentify message
 * sequence and send it to the target.  In addition, if the MK_MESSAGE bit
 * is set in the SCB_CONTROL byte, interrupt the host and allow it to send
 * it's own message.
 *
 * If MSG_OUT is == HOST_MSG, also interrupt the host and take a message.
 * This is done to allow the hsot to send messages outside of an identify
 * sequence while protecting the seqencer from testing the MK_MESSAGE bit
 * on an SCB that might not be for the current nexus. (For example, a
 * BDR message in responce to a bad reselection would leave us pointed to
 * an SCB that doesn't have anything to do with the current target).
 * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag,
 * bus device reset).
 *
 * When there are no messages to send, MSG_OUT should be set to MSG_NOOP,
 * in case the target decides to put us in this phase for some strange
 * reason.
 */
p_mesgout:
        mov     SINDEX, MSG_OUT;
        cmp     SINDEX, MSG_IDENTIFYFLAG jne p_mesgout_from_host;
p_mesgout_identify:
        if ((p->features & AHC_WIDE) != 0) {
                and     SINDEX,0xf,SCB_TCL;     /* lun */
        } else {
                and     SINDEX,0x7,SCB_TCL;     /* lun */
        }
        and     A,DISCENB,SCB_CONTROL;  /* mask off disconnect privledge */
        or      SINDEX,A;               /* or in disconnect privledge */
        or      SINDEX,MSG_IDENTIFYFLAG;
p_mesgout_mk_message:
        test    SCB_CONTROL,MK_MESSAGE  jz p_mesgout_tag;
        mov     SCSIDATL, SINDEX;       /* Send the last byte */
        jmp     p_mesgout_from_host + 1;/* Skip HOST_MSG test */
/*
 * Send a tag message if TAG_ENB is set in the SCB control block.
 * Use SCB_TAG (the position in the kernel's SCB array) as the tag value.
 */
p_mesgout_tag:
        test    SCB_CONTROL,TAG_ENB jz  p_mesgout_onebyte;
        mov     SCSIDATL, SINDEX;       /* Send the identify message */
        call    phase_lock;
        cmp     LASTPHASE, P_MESGOUT    jne p_mesgout_done;
        and     SCSIDATL,TAG_ENB|SCB_TAG_TYPE,SCB_CONTROL;
        call    phase_lock;
        cmp     LASTPHASE, P_MESGOUT    jne p_mesgout_done;
        mov     SCB_TAG jmp p_mesgout_onebyte;
/*
 * Interrupt the driver, and allow it to send a message
 * if it asks.
 */
p_mesgout_from_host:
        cmp     SINDEX, HOST_MSG        jne p_mesgout_onebyte;
        mvi     INTSTAT,AWAITING_MSG;
        nop;
        /*
         * Did the host detect a phase change?
         */
        cmp     RETURN_1, MSGOUT_PHASEMIS je p_mesgout_done;
 
p_mesgout_onebyte:
        mvi     CLRSINT1, CLRATNO;
        mov     SCSIDATL, SINDEX;
 
/*
 * If the next bus phase after ATN drops is a message out, it means
 * that the target is requesting that the last message(s) be resent.
 */
        call    phase_lock;
        cmp     LASTPHASE, P_MESGOUT    jne p_mesgout_done;
        or      SCSISIGO,ATNO,LASTPHASE;/* turn on ATN for the retry */
        jmp     p_mesgout;
 
p_mesgout_done:
        mvi     CLRSINT1,CLRATNO;       /* Be sure to turn ATNO off */
        mov     LAST_MSG, MSG_OUT;
        cmp     MSG_OUT, MSG_IDENTIFYFLAG jne . + 2;
        and     SCB_CONTROL, ~MK_MESSAGE;
        mvi     MSG_OUT, MSG_NOOP;      /* No message left */
        jmp     ITloop;
 
/*
 * Message in phase.  Bytes are read using Automatic PIO mode.
 */
p_mesgin:
        mvi     ACCUM           call inb_first; /* read the 1st message byte */
 
        test    A,MSG_IDENTIFYFLAG      jnz mesgin_identify;
        cmp     A,MSG_DISCONNECT        je mesgin_disconnect;
        cmp     A,MSG_SAVEDATAPOINTER   je mesgin_sdptrs;
        cmp     ALLZEROS,A              je mesgin_complete;
        cmp     A,MSG_RESTOREPOINTERS   je mesgin_rdptrs;
        cmp     A,MSG_EXTENDED          je mesgin_extended;
        cmp     A,MSG_MESSAGE_REJECT    je mesgin_reject;
        cmp     A,MSG_NOOP              je mesgin_done;
 
rej_mesgin:
/*
 * We have no idea what this message in is, so we issue a message reject
 * and hope for the best.  In any case, rejection should be a rare
 * occurrence - signal the driver when it happens.
 */
        mvi     INTSTAT,SEND_REJECT;            /* let driver know */
 
        mvi     MSG_MESSAGE_REJECT      call mk_mesg;
 
mesgin_done:
        mov     NONE,SCSIDATL;          /*dummy read from latch to ACK*/
        jmp     ITloop;
 
 
mesgin_complete:
/*
 * We got a "command complete" message, so put the SCB_TAG into the QOUTFIFO,
 * and trigger a completion interrupt.  Before doing so, check to see if there
 * is a residual or the status byte is something other than STATUS_GOOD (0).
 * In either of these conditions, we upload the SCB back to the host so it can
 * process this information.  In the case of a non zero status byte, we
 * additionally interrupt the kernel driver synchronously, allowing it to
 * decide if sense should be retrieved.  If the kernel driver wishes to request
 * sense, it will fill the kernel SCB with a request sense command and set
 * RETURN_1 to SEND_SENSE.  If RETURN_1 is set to SEND_SENSE we redownload
 * the SCB, and process it as the next command by adding it to the waiting list.
 * If the kernel driver does not wish to request sense, it need only clear
 * RETURN_1, and the command is allowed to complete normally.  We don't bother
 * to post to the QOUTFIFO in the error cases since it would require extra
 * work in the kernel driver to ensure that the entry was removed before the
 * command complete code tried processing it.
 */
 
/*
 * First check for residuals
 */
        test    SCB_RESID_SGCNT,0xff    jnz upload_scb;
        test    SCB_TARGET_STATUS,0xff  jz complete;    /* Good Status? */
upload_scb:
        mvi     DMAPARAMS, FIFORESET;
        mov     SCB_TAG         call dma_scb;
check_status:
        test    SCB_TARGET_STATUS,0xff  jz complete;    /* Just a residual? */
        mvi     INTSTAT,BAD_STATUS;                     /* let driver know */
        nop;
        cmp     RETURN_1, SEND_SENSE    jne complete;
        /* This SCB becomes the next to execute as it will retrieve sense */
        mvi     DMAPARAMS, HDMAEN|DIRECTION|FIFORESET;
        mov     SCB_TAG         call dma_scb;
add_to_waiting_list:
        mov     SCB_NEXT,WAITING_SCBH;
        mov     WAITING_SCBH, SCBPTR;
        /*
         * Prepare our selection hardware before the busfree so we have a
         * high probability of winning arbitration.
         */
        call    start_selection;
        jmp     await_busfree;
 
complete:
        /* If we are untagged, clear our address up in host ram */
        test    SCB_CONTROL, TAG_ENB jnz complete_post;
        mov     A, SAVED_TCL;
        mvi     UNTAGGEDSCB_OFFSET call post_byte_setup;
        mvi     SCB_LIST_NULL call post_byte;
 
complete_post:
        /* Post the SCB and issue an interrupt */
        if ((p->features & AHC_QUEUE_REGS) != 0) {
                mov     A, SDSCB_QOFF;
        } else {
                mov     A, QOUTPOS;
        }
        mvi     QOUTFIFO_OFFSET call post_byte_setup;
        mov     SCB_TAG call post_byte;
        if ((p->features & AHC_QUEUE_REGS) == 0) {
                inc     QOUTPOS;
        }
        mvi     INTSTAT,CMDCMPLT;
 
add_to_free_list:
        call    add_scb_to_free_list;
        jmp     await_busfree;
 
/*
 * Is it an extended message?  Copy the message to our message buffer and
 * notify the host.  The host will tell us whether to reject this message,
 * respond to it with the message that the host placed in our message buffer,
 * or simply to do nothing.
 */
mesgin_extended:
        mvi     INTSTAT,EXTENDED_MSG;           /* let driver know */
        jmp     ITloop;
 
/*
 * Is it a disconnect message?  Set a flag in the SCB to remind us
 * and await the bus going free.
 */
mesgin_disconnect:
        or      SCB_CONTROL,DISCONNECTED;
        call    add_scb_to_disc_list;
        jmp     await_busfree;
 
/*
 * Save data pointers message:
 * Copying RAM values back to SCB, for Save Data Pointers message, but
 * only if we've actually been into a data phase to change them.  This
 * protects against bogus data in scratch ram and the residual counts
 * since they are only initialized when we go into data_in or data_out.
 */
mesgin_sdptrs:
        test    SEQ_FLAGS, DPHASE       jz mesgin_done;
        mov     SCB_SGCOUNT,SG_COUNT;
 
        /* The SCB SGPTR becomes the next one we'll download */
        mvi     DINDEX, SCB_SGPTR;
        mvi     SG_NEXT call bcopy_4;
 
        /* The SCB DATAPTR0 becomes the current SHADDR */
        mvi     DINDEX, SCB_DATAPTR;
        mvi     SHADDR          call bcopy_4;
 
/*
 * Use the residual number since STCNT is corrupted by any message transfer.
 */
        mvi     SCB_RESID_DCNT  call    bcopy_3;
 
        jmp     mesgin_done;
 
/*
 * Restore pointers message?  Data pointers are recopied from the
 * SCB anytime we enter a data phase for the first time, so all
 * we need to do is clear the DPHASE flag and let the data phase
 * code do the rest.
 */
mesgin_rdptrs:
        and     SEQ_FLAGS, ~DPHASE;             /*
                                                 * We'll reload them
                                                 * the next time through
                                                 * the dataphase.
                                                 */
        jmp     mesgin_done;
 
/*
 * Identify message?  For a reconnecting target, this tells us the lun
 * that the reconnection is for - find the correct SCB and switch to it,
 * clearing the "disconnected" bit so we don't "find" it by accident later.
 */
mesgin_identify:
 
        if ((p->features & AHC_WIDE) != 0) {
                and     A,0x0f;         /* lun in lower four bits */
        } else {
                and     A,0x07;         /* lun in lower three bits */
        }
        or      SAVED_TCL,A;            /* SAVED_TCL should be complete now */
 
        call    get_untagged_SCBID;
        cmp     ARG_1, SCB_LIST_NULL    je snoop_tag;
        if ((p->flags & AHC_PAGESCBS) != 0) {
                test    SEQ_FLAGS, SCBPTR_VALID jz use_retrieveSCB;
        }
        /*
         * If the SCB was found in the disconnected list (as is
         * always the case in non-paging scenarios), SCBPTR is already
         * set to the correct SCB.  So, simply setup the SCB and get
         * on with things.
         */
        mov     SCBPTR  call rem_scb_from_disc_list;
        jmp     setup_SCB;
/*
 * Here we "snoop" the bus looking for a SIMPLE QUEUE TAG message.
 * If we get one, we use the tag returned to find the proper
 * SCB.  With SCB paging, this requires using search for both tagged
 * and non-tagged transactions since the SCB may exist in any slot.
 * If we're not using SCB paging, we can use the tag as the direct
 * index to the SCB.
 */
snoop_tag:
        mov     NONE,SCSIDATL;          /* ACK Identify MSG */
snoop_tag_loop:
        call    phase_lock;
        cmp     LASTPHASE, P_MESGIN     jne not_found;
        cmp     SCSIBUSL,MSG_SIMPLE_Q_TAG jne not_found;
get_tag:
        mvi     ARG_1   call inb_next;  /* tag value */
 
        if ((p->flags & AHC_PAGESCBS) == 0) {
index_by_tag:
                mov     SCBPTR,ARG_1;
                test    SCB_CONTROL,TAG_ENB     jz  not_found;
                mov     SCBPTR  call rem_scb_from_disc_list;
        } else {
                /*
                 * Ensure that the SCB the tag points to is for
                 * an SCB transaction to the reconnecting target.
                 */
use_retrieveSCB:
                call    retrieveSCB;
        }
setup_SCB:
        mov     A, SAVED_TCL;
        cmp     SCB_TCL, A      jne not_found_cleanup_scb;
        test    SCB_CONTROL,DISCONNECTED jz not_found_cleanup_scb;
        and     SCB_CONTROL,~DISCONNECTED;
        or      SEQ_FLAGS,IDENTIFY_SEEN;          /* make note of IDENTIFY */
        /* See if the host wants to send a message upon reconnection */
        test    SCB_CONTROL, MK_MESSAGE jz mesgin_done;
        and     SCB_CONTROL, ~MK_MESSAGE;
        mvi     HOST_MSG        call mk_mesg;
        jmp     mesgin_done;
 
not_found_cleanup_scb:
        test    SCB_CONTROL, DISCONNECTED jz . + 3;
        call    add_scb_to_disc_list;
        jmp     not_found;
        call    add_scb_to_free_list;
not_found:
        mvi     INTSTAT, NO_MATCH;
        mvi     MSG_BUS_DEV_RESET       call mk_mesg;
        jmp     mesgin_done;
 
/*
 * Message reject?  Let the kernel driver handle this.  If we have an
 * outstanding WDTR or SDTR negotiation, assume that it's a response from
 * the target selecting 8bit or asynchronous transfer, otherwise just ignore
 * it since we have no clue what it pertains to.
 */
mesgin_reject:
        mvi     INTSTAT, REJECT_MSG;
        jmp     mesgin_done;
 
/*
 * [ ADD MORE MESSAGE HANDLING HERE ]
 */
 
/*
 * Locking the driver out, build a one-byte message passed in SINDEX
 * if there is no active message already.  SINDEX is returned intact.
 */
mk_mesg:
        or      SCSISIGO,ATNO,LASTPHASE;/* turn on ATNO */
        mov     MSG_OUT,SINDEX ret;
 
/*
 * Functions to read data in Automatic PIO mode.
 *
 * According to Adaptec's documentation, an ACK is not sent on input from
 * the target until SCSIDATL is read from.  So we wait until SCSIDATL is
 * latched (the usual way), then read the data byte directly off the bus
 * using SCSIBUSL.  When we have pulled the ATN line, or we just want to
 * acknowledge the byte, then we do a dummy read from SCISDATL.  The SCSI
 * spec guarantees that the target will hold the data byte on the bus until
 * we send our ACK.
 *
 * The assumption here is that these are called in a particular sequence,
 * and that REQ is already set when inb_first is called.  inb_{first,next}
 * use the same calling convention as inb.
 */
 
inb_next:
        mov     NONE,SCSIDATL;          /*dummy read from latch to ACK*/
inb_next_wait:
        /*
         * If there is a parity error, wait for the kernel to
         * see the interrupt and prepare our message response
         * before continuing.
         */
        test    SSTAT1, REQINIT jz inb_next_wait;
        test    SSTAT1, SCSIPERR jnz inb_next_wait;
        and     LASTPHASE, PHASE_MASK, SCSISIGI;
        cmp     LASTPHASE, P_MESGIN jne mesgin_phasemis;
inb_first:
        mov     DINDEX,SINDEX;
        mov     DINDIR,SCSIBUSL ret;            /*read byte directly from bus*/
inb_last:
        mov     NONE,SCSIDATL ret;              /*dummy read from latch to ACK*/
 
if ((p->flags & AHC_TARGETMODE) != 0) {
        /*
         * Send a byte to an initiator in Automatic PIO mode.
         * SPIOEN must be on prior to calling this routine.
         */
target_outb:
        mov     SCSIDATL, SINDEX;
        test    SSTAT0, SPIORDY jz .;
        ret;
}
 
mesgin_phasemis:
/*
 * We expected to receive another byte, but the target changed phase
 */
        mvi     INTSTAT, MSGIN_PHASEMIS;
        jmp     ITloop;
 
/*
 * DMA data transfer.  HADDR and HCNT must be loaded first, and
 * SINDEX should contain the value to load DFCNTRL with - 0x3d for
 * host->scsi, or 0x39 for scsi->host.  The SCSI channel is cleared
 * during initialization.
 */
dma:
        mov     DFCNTRL,SINDEX;
dma_loop:
        test    SSTAT0,DMADONE  jnz dma_dmadone;
        test    SSTAT1,PHASEMIS jz dma_loop;    /* ie. underrun */
dma_phasemis:
        test    SSTAT0,SDONE    jnz dma_checkfifo;
        mov     SINDEX,ALLZEROS;                /* Notify caller of phasemiss */
 
/*
 * We will be "done" DMAing when the transfer count goes to zero, or
 * the target changes the phase (in light of this, it makes sense that
 * the DMA circuitry doesn't ACK when PHASEMIS is active).  If we are
 * doing a SCSI->Host transfer, the data FIFO should be flushed auto-
 * magically on STCNT=0 or a phase change, so just wait for FIFO empty
 * status.
 */
dma_checkfifo:
        test    DFCNTRL,DIRECTION       jnz dma_fifoempty;
dma_fifoflush:
        test    DFSTATUS,FIFOEMP        jz dma_fifoflush;
 
dma_fifoempty:
        /* Don't clobber an inprogress host data transfer */
        test    DFSTATUS, MREQPEND      jnz dma_fifoempty;
/*
 * Now shut the DMA enables off and make sure that the DMA enables are
 * actually off first lest we get an ILLSADDR.
 */
dma_dmadone:
        and     DFCNTRL, ~(SCSIEN|SDMAEN|HDMAEN);
dma_halt:
        /*
         * Some revisions of the aic7880 have a problem where, if the
         * data fifo is full, but the PCI input latch is not empty,
         * HDMAEN cannot be cleared.  The fix used here is to attempt
         * to drain the data fifo until there is space for the input
         * latch to drain and HDMAEN de-asserts.
         */
        if ((p->features & AHC_ULTRA2) == 0) {
                mov     NONE, DFDAT;
        }
        test    DFCNTRL, HDMAEN jnz dma_halt;
return:
        ret;
 
/*
 * Assert that if we've been reselected, then we've seen an IDENTIFY
 * message.
 */
assert:
        test    SEQ_FLAGS,IDENTIFY_SEEN jnz return;     /* seen IDENTIFY? */
 
        mvi     INTSTAT,NO_IDENT        ret;    /* no - tell the kernel */
 
/*
 * Locate a disconnected SCB either by SAVED_TCL (ARG_1 is SCB_LIST_NULL)
 * or by the SCBID ARG_1.  The search begins at the SCB index passed in
 * via SINDEX which is an SCB that must be on the disconnected list.  If
 * the SCB cannot be found, SINDEX will be SCB_LIST_NULL, otherwise, SCBPTR
 * is set to the proper SCB.
 */
findSCB:
        mov     SCBPTR,SINDEX;                  /* Initialize SCBPTR */
        cmp     ARG_1, SCB_LIST_NULL    jne findSCB_by_SCBID;
        mov     A, SAVED_TCL;
        mvi     SCB_TCL jmp findSCB_loop;       /* &SCB_TCL -> SINDEX */
findSCB_by_SCBID:
        mov     A, ARG_1;                       /* Tag passed in ARG_1 */
        mvi     SCB_TAG jmp findSCB_loop;       /* &SCB_TAG -> SINDEX */
findSCB_next:
        cmp     SCB_NEXT, SCB_LIST_NULL je notFound;
        mov     SCBPTR,SCB_NEXT;
        dec     SINDEX;         /* Last comparison moved us too far */
findSCB_loop:
        cmp     SINDIR, A       jne findSCB_next;
        mov     SINDEX, SCBPTR  ret;
notFound:
        mvi     SINDEX, SCB_LIST_NULL   ret;
 
/*
 * Retrieve an SCB by SCBID first searching the disconnected list falling
 * back to DMA'ing the SCB down from the host.  This routine assumes that
 * ARG_1 is the SCBID of interrest and that SINDEX is the position in the
 * disconnected list to start the search from.  If SINDEX is SCB_LIST_NULL,
 * we go directly to the host for the SCB.
 */
retrieveSCB:
        test    SEQ_FLAGS, SCBPTR_VALID jz retrieve_from_host;
        mov     SCBPTR  call findSCB;   /* Continue the search */
        cmp     SINDEX, SCB_LIST_NULL   je retrieve_from_host;
 
/*
 * This routine expects SINDEX to contain the index of the SCB to be
 * removed and SCBPTR to be pointing to that SCB.
 */
rem_scb_from_disc_list:
/* Remove this SCB from the disconnection list */
        cmp     SCB_NEXT,SCB_LIST_NULL je unlink_prev;
        mov     DINDEX, SCB_PREV;
        mov     SCBPTR, SCB_NEXT;
        mov     SCB_PREV, DINDEX;
        mov     SCBPTR, SINDEX;
unlink_prev:
        cmp     SCB_PREV,SCB_LIST_NULL  je rHead;/* At the head of the list */
        mov     DINDEX, SCB_NEXT;
        mov     SCBPTR, SCB_PREV;
        mov     SCB_NEXT, DINDEX;
        mov     SCBPTR, SINDEX ret;
rHead:
        mov     DISCONNECTED_SCBH,SCB_NEXT ret;
 
retrieve_from_host:
/*
 * We didn't find it.  Pull an SCB and DMA down the one we want.
 * We should never get here in the non-paging case.
 */
        mov     ALLZEROS        call    get_free_or_disc_scb;
        mvi     DMAPARAMS, HDMAEN|DIRECTION|FIFORESET;
        /* Jump instead of call as we want to return anyway */
        mov     ARG_1   jmp dma_scb;
 
/*
 * Determine whether a target is using tagged or non-tagged transactions
 * by first looking for a matching transaction based on the TCL and if
 * that fails, looking up this device in the host's untagged SCB array.
 * The TCL to search for is assumed to be in SAVED_TCL.  The value is
 * returned in ARG_1 (SCB_LIST_NULL for tagged, SCBID for non-tagged).
 * The SCBPTR_VALID bit is set in SEQ_FLAGS if we found the information
 * in an SCB instead of having to go to the host.
 */
get_untagged_SCBID:
        cmp     DISCONNECTED_SCBH, SCB_LIST_NULL je get_SCBID_from_host;
        mvi     ARG_1, SCB_LIST_NULL;
        mov     DISCONNECTED_SCBH call findSCB;
        cmp     SINDEX, SCB_LIST_NULL   je get_SCBID_from_host;
        or      SEQ_FLAGS, SCBPTR_VALID;/* Was in disconnected list */
        test    SCB_CONTROL, TAG_ENB    jnz . + 2;
        mov     ARG_1, SCB_TAG  ret;
        mvi     ARG_1, SCB_LIST_NULL ret;
 
/*
 * Fetch a byte from host memory given an index of (A + (256 * SINDEX))
 * and a base address of SCBID_ADDR.  The byte is returned in RETURN_2.
 */
fetch_byte:
        mov     ARG_2, SINDEX;
        if ((p->features & AHC_CMD_CHAN) != 0) {
                mvi     DINDEX, CCHADDR;
                mvi     SCBID_ADDR call set_1byte_addr;
                mvi     CCHCNT, 1;
                mvi     CCSGCTL, CCSGEN|CCSGRESET;
                test    CCSGCTL, CCSGDONE jz .;
                mvi     CCSGCTL, CCSGRESET;
                bmov    RETURN_2, CCSGRAM, 1 ret;
        } else {
                mvi     DINDEX, HADDR;
                mvi     SCBID_ADDR call set_1byte_addr;
                mvi     HCNT[0], 1;
                clr     HCNT[1];
                clr     HCNT[2];
                mvi     DFCNTRL, HDMAEN|DIRECTION|FIFORESET;
                call    dma_finish;
                mov     RETURN_2, DFDAT ret;
        }
 
/*
 * Prepare the hardware to post a byte to host memory given an
 * index of (A + (256 * SINDEX)) and a base address of SCBID_ADDR.
 */
post_byte_setup:
        mov     ARG_2, SINDEX;
        if ((p->features & AHC_CMD_CHAN) != 0) {
                mvi     DINDEX, CCHADDR;
                mvi     SCBID_ADDR call set_1byte_addr;
                mvi     CCHCNT, 1;
                mvi     CCSCBCTL, CCSCBRESET ret;
        } else {
                mvi     DINDEX, HADDR;
                mvi     SCBID_ADDR call set_1byte_addr;
                mvi     HCNT[0], 1;
                clr     HCNT[1];
                clr     HCNT[2];
                mvi     DFCNTRL, FIFORESET ret;
        }
 
post_byte:
        if ((p->features & AHC_CMD_CHAN) != 0) {
                bmov    CCSCBRAM, SINDEX, 1;
                or      CCSCBCTL, CCSCBEN|CCSCBRESET;
                test    CCSCBCTL, CCSCBDONE jz .;
                clr     CCSCBCTL ret;
        } else {
                mov     DFDAT, SINDEX;
                or      DFCNTRL, HDMAEN|FIFOFLUSH;
                jmp     dma_finish;
        }
 
get_SCBID_from_host:
        mov     A, SAVED_TCL;
        mvi     UNTAGGEDSCB_OFFSET call fetch_byte;
        mov     RETURN_1,  RETURN_2 ret;
 
phase_lock:
        test    SSTAT1, REQINIT jz phase_lock;
        test    SSTAT1, SCSIPERR jnz phase_lock;
        and     LASTPHASE, PHASE_MASK, SCSISIGI;
        mov     SCSISIGO, LASTPHASE ret;
 
set_stcnt_from_hcnt:
        mov     STCNT[0], HCNT[0];
        mov     STCNT[1], HCNT[1];
        mov     STCNT[2], HCNT[2] ret;
 
bcopy_7:
        mov     DINDIR, SINDIR;
        mov     DINDIR, SINDIR;
bcopy_5:
        mov     DINDIR, SINDIR;
bcopy_4:
        mov     DINDIR, SINDIR;
bcopy_3:
        mov     DINDIR, SINDIR;
        mov     DINDIR, SINDIR;
        mov     DINDIR, SINDIR ret;
 
/*
 * Setup addr assuming that A is an index into
 * an array of 32byte objects, SINDEX contains
 * the base address of that array, and DINDEX
 * contains the base address of the location
 * to store the indexed address.
 */
set_32byte_addr:
        shr     ARG_2, 3, A;
        shl     A, 5;
/*
 * Setup addr assuming that A + (ARG_1 * 256) is an
 * index into an array of 1byte objects, SINDEX contains
 * the base address of that array, and DINDEX contains
 * the base address of the location to store the computed
 * address.
 */
set_1byte_addr:
        add     DINDIR, A, SINDIR;
        mov     A, ARG_2;
        adc     DINDIR, A, SINDIR;
        clr     A;
        adc     DINDIR, A, SINDIR;
        adc     DINDIR, A, SINDIR ret;
 
/*
 * Either post or fetch and SCB from host memory based on the
 * DIRECTION bit in DMAPARAMS. The host SCB index is in SINDEX.
 */
dma_scb:
        mov     A, SINDEX;
        if ((p->features & AHC_CMD_CHAN) != 0) {
                mvi     DINDEX, CCHADDR;
                mvi     HSCB_ADDR call set_32byte_addr;
                mov     CCSCBPTR, SCBPTR;
                mvi     CCHCNT, 32;
                test    DMAPARAMS, DIRECTION jz dma_scb_tohost;
                mvi     CCSCBCTL, CCARREN|CCSCBEN|CCSCBDIR|CCSCBRESET;
                cmp     CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN|CCSCBDIR jne .;
                jmp     dma_scb_finish;
dma_scb_tohost:
                if ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) {
                        mvi     CCSCBCTL, CCSCBRESET;
                        bmov    CCSCBRAM, SCB_CONTROL, 32;
                        or      CCSCBCTL, CCSCBEN|CCSCBRESET;
                        test    CCSCBCTL, CCSCBDONE jz .;
                } else {
                        mvi     CCSCBCTL, CCARREN|CCSCBEN|CCSCBRESET;
                        cmp     CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN jne .;
                }
dma_scb_finish:
                clr     CCSCBCTL;
                test    CCSCBCTL, CCARREN|CCSCBEN jnz .;
                ret;
        } else {
                mvi     DINDEX, HADDR;
                mvi     HSCB_ADDR call set_32byte_addr;
                mvi     HCNT[0], 32;
                clr     HCNT[1];
                clr     HCNT[2];
                mov     DFCNTRL, DMAPARAMS;
                test    DMAPARAMS, DIRECTION    jnz dma_scb_fromhost;
                /* Fill it with the SCB data */
copy_scb_tofifo:
                mvi     SINDEX, SCB_CONTROL;
                add     A, 32, SINDEX;
copy_scb_tofifo_loop:
                mov     DFDAT,SINDIR;
                mov     DFDAT,SINDIR;
                mov     DFDAT,SINDIR;
                mov     DFDAT,SINDIR;
                mov     DFDAT,SINDIR;
                mov     DFDAT,SINDIR;
                mov     DFDAT,SINDIR;
                mov     DFDAT,SINDIR;
                cmp     SINDEX, A jne copy_scb_tofifo_loop;
                or      DFCNTRL, HDMAEN|FIFOFLUSH;
dma_scb_fromhost:
                call    dma_finish;
                /* If we were putting the SCB, we are done */
                test    DMAPARAMS, DIRECTION    jz      return;
                mvi     SCB_CONTROL  call dfdat_in_7;
                call    dfdat_in_7_continued;
                call    dfdat_in_7_continued;
                jmp     dfdat_in_7_continued;
dfdat_in_7:
                mov     DINDEX,SINDEX;
dfdat_in_7_continued:
                mov     DINDIR,DFDAT;
                mov     DINDIR,DFDAT;
                mov     DINDIR,DFDAT;
                mov     DINDIR,DFDAT;
                mov     DINDIR,DFDAT;
                mov     DINDIR,DFDAT;
                mov     DINDIR,DFDAT ret;
        }
 
 
/*
 * Wait for DMA from host memory to data FIFO to complete, then disable
 * DMA and wait for it to acknowledge that it's off.
 */
dma_finish:
        test    DFSTATUS,HDONE  jz dma_finish;
        /* Turn off DMA */
        and     DFCNTRL, ~HDMAEN;
        test    DFCNTRL, HDMAEN jnz .;
        ret;
 
add_scb_to_free_list:
        if ((p->flags & AHC_PAGESCBS) != 0) {
                mov     SCB_NEXT, FREE_SCBH;
                mov     FREE_SCBH, SCBPTR;
        }
        mvi     SCB_TAG, SCB_LIST_NULL ret;
 
if ((p->flags & AHC_PAGESCBS) != 0) {
get_free_or_disc_scb:
        cmp     FREE_SCBH, SCB_LIST_NULL jne dequeue_free_scb;
        cmp     DISCONNECTED_SCBH, SCB_LIST_NULL jne dequeue_disc_scb;
return_error:
        mvi     SINDEX, SCB_LIST_NULL   ret;
dequeue_disc_scb:
        mov     SCBPTR, DISCONNECTED_SCBH;
dma_up_scb:
        mvi     DMAPARAMS, FIFORESET;
        mov     SCB_TAG         call dma_scb;
unlink_disc_scb:
        /* jmp instead of call since we want to return anyway */
        mov     SCBPTR  jmp rem_scb_from_disc_list;
dequeue_free_scb:
        mov     SCBPTR, FREE_SCBH;
        mov     FREE_SCBH, SCB_NEXT ret;
}
 
add_scb_to_disc_list:
/*
 * Link this SCB into the DISCONNECTED list.  This list holds the
 * candidates for paging out an SCB if one is needed for a new command.
 * Modifying the disconnected list is a critical(pause dissabled) section.
 */
        mvi     SCB_PREV, SCB_LIST_NULL;
        mov     SCB_NEXT, DISCONNECTED_SCBH;
        mov     DISCONNECTED_SCBH, SCBPTR;
        cmp     SCB_NEXT,SCB_LIST_NULL je return;
        mov     SCBPTR,SCB_NEXT;
        mov     SCB_PREV,DISCONNECTED_SCBH;
        mov     SCBPTR,DISCONNECTED_SCBH ret;
Browse

Tools

Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [drivers/] [scsi/] [aic7xxx/] [aic7xxx.seq] - Blame information for rev 1626

Line No.	Rev	Author	Line
1	1626	jcastillo	`/*`
2			`* Adaptec 274x/284x/294x device driver firmware for Linux and FreeBSD.`
3			`*`
4			`* Copyright (c) 1994-1998 Justin Gibbs.`
5			`* All rights reserved.`
6			`*`
7			`* Redistribution and use in source and binary forms, with or without`
8			`* modification, are permitted provided that the following conditions`
9			`* are met:`
10			`* 1. Redistributions of source code must retain the above copyright`
11			`* notice, this list of conditions, and the following disclaimer,`
12			`* without modification, immediately at the beginning of the file.`
13			`* 2. The name of the author may not be used to endorse or promote products`
14			`* derived from this software without specific prior written permission.`
15			`*`
16			`* Where this Software is combined with software released under the terms of`
17			`* the GNU Public License (GPL) and the terms of the GPL would require the`
18			`* combined work to also be released under the terms of the GPL, the terms`
19			`* and conditions of this License will apply in addition to those of the`
20			`* GPL with the exception of any terms or conditions of this License that`
21			`* conflict with, or are expressly prohibited by, the GPL.`
22			`*`
23			* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
24			`* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE`
25			`* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE`
26			`* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR`
27			`* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL`
28			`* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS`
29			`* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)`
30			`* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT`
31			`* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY`
32			`* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF`
33			`* SUCH DAMAGE.`
34			`*`
35			`* $Id: aic7xxx.seq,v 1.1 2005-12-20 10:18:04 jcastillo Exp $`
36			`*/`
37
38			`#include "aic7xxx.reg"`
39			`#include "scsi_message.h"`
40