Subversion Repositories or1k

/*

 * DTC controller, taken from T128 driver by...

 * Copyright 1993, Drew Eckhardt

 *      Visionary Computing

 *      (Unix and Linux consulting and custom programming)

 *      drew@colorado.edu

 *      +1 (303) 440-4894

 *

 * DISTRIBUTION RELEASE 1.

 *

 * For more information, please consult

 *

 *

 *

 * and

 *

 * NCR 5380 Family

 * SCSI Protocol Controller

 * Databook

 *

 * NCR Microelectronics

 * 1635 Aeroplaza Drive

 * Colorado Springs, CO 80916

 * 1+ (719) 578-3400

 * 1+ (800) 334-5454

 */

#ifndef DTC3280_H

#define DTC3280_H

#define DTC_PUBLIC_RELEASE 1

/*#define DTCDEBUG 0x1*/

#define DTCDEBUG_INIT   0x1

#define DTCDEBUG_TRANSFER 0x2

/*

 * The DTC3180 & 3280 boards are memory mapped.

 *

 */

/*

 */

/* Offset from DTC_5380_OFFSET */

#define DTC_CONTROL_REG         0x100   /* rw */

#define D_CR_ACCESS             0x80    /* ro set=can access 3280 registers */

#define CSR_DIR_READ            0x40    /* rw direction, 1 = read 0 = write */

#define CSR_RESET              0x80    /* wo  Resets 53c400 */

#define CSR_5380_REG           0x80    /* ro  5380 registers can be accessed */

#define CSR_TRANS_DIR          0x40    /* rw  Data transfer direction */

#define CSR_SCSI_BUFF_INTR     0x20    /* rw  Enable int on transfer ready */

#define CSR_5380_INTR          0x10    /* rw  Enable 5380 interrupts */

#define CSR_SHARED_INTR        0x08    /* rw  Interrupt sharing */

#define CSR_HOST_BUF_NOT_RDY   0x04    /* ro  Host buffer not ready */

#define CSR_SCSI_BUF_RDY       0x02    /* ro  SCSI buffer ready */

#define CSR_GATED_5380_IRQ     0x01    /* ro  Last block xferred */

#define CSR_INT_BASE (CSR_SCSI_BUFF_INTR | CSR_5380_INTR)

#define DTC_BLK_CNT             0x101   /* rw 

                                         * # of 128-byte blocks to transfer */

#define D_CR_ACCESS             0x80    /* ro set=can access 3280 registers */

#define DTC_SWITCH_REG          0x3982  /* ro - DIP switches */

#define DTC_RESUME_XFER         0x3982  /* wo - resume data xfer 

                                           * after disconnect/reconnect*/

#define DTC_5380_OFFSET         0x3880  /* 8 registers here, see NCR5380.h */

/*!!!! for dtc, it's a 128 byte buffer at 3900 !!! */

#define DTC_DATA_BUF            0x3900  /* rw 128 bytes long */

#ifndef ASM

int dtc_abort(Scsi_Cmnd *);

int dtc_biosparam(Disk *, kdev_t, int*);

int dtc_detect(Scsi_Host_Template *);

int dtc_queue_command(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));

int dtc_reset(Scsi_Cmnd *, unsigned int reset_flags);

int dtc_proc_info (char *buffer, char **start, off_t offset,

                   int length, int hostno, int inout);

#ifndef NULL

#define NULL 0

#endif

#ifndef CMD_PER_LUN

#define CMD_PER_LUN 2

#endif

#ifndef CAN_QUEUE

#define CAN_QUEUE 32 

#endif

/*

 * I hadn't thought of this with the earlier drivers - but to prevent

 * macro definition conflicts, we shouldn't define all of the internal

 * macros when this is being used solely for the host stub.

 */

#if defined(HOSTS_C) || defined(MODULE)

#define DTC3x80 {NULL, NULL, NULL, NULL, \

        "DTC 3180/3280 ", dtc_detect, NULL,  \

        NULL,                                                   \

        NULL, dtc_queue_command, dtc_abort, dtc_reset, NULL,    \

        dtc_biosparam,                                          \

        /* can queue */ CAN_QUEUE, /* id */ 7, SG_ALL,                  \

        /* cmd per lun */ CMD_PER_LUN , 0, 0, DISABLE_CLUSTERING}

#endif

#ifndef HOSTS_C

#define NCR5380_implementation_fields \

    volatile unsigned char *base

#define NCR5380_local_declare() \

    volatile unsigned char *base

#define NCR5380_setup(instance) \

    base = (volatile unsigned char *) (instance)->base

#define DTC_address(reg) (base + DTC_5380_OFFSET + reg)

#define dbNCR5380_read(reg)                                              \

    (rval=*(DTC_address(reg)), \

     (((unsigned char) printk("DTC : read register %d at addr %08x is: %02x\n"\

    , (reg), (int)DTC_address(reg), rval)), rval ) )

#define dbNCR5380_write(reg, value) do {                                  \

    printk("DTC : write %02x to register %d at address %08x\n",         \

            (value), (reg), (int)DTC_address(reg));     \

    *(DTC_address(reg)) = (value);} while(0)

#if !(DTCDEBUG & DTCDEBUG_TRANSFER) 

#define NCR5380_read(reg) (*(DTC_address(reg)))

#define NCR5380_write(reg, value) (*(DTC_address(reg)) = (value))

#else

#define NCR5380_read(reg) (*(DTC_address(reg)))

#define xNCR5380_read(reg)                                              \

    (((unsigned char) printk("DTC : read register %d at address %08x\n"\

    , (reg), DTC_address(reg))), *(DTC_address(reg)))

#define NCR5380_write(reg, value) do {                                  \

    printk("DTC : write %02x to register %d at address %08x\n",         \

            (value), (reg), (int)DTC_address(reg));     \

    *(DTC_address(reg)) = (value);              } while(0)

#endif

#define NCR5380_intr dtc_intr

#define NCR5380_queue_command dtc_queue_command

#define NCR5380_abort dtc_abort

#define NCR5380_reset dtc_reset

#define NCR5380_proc_info dtc_proc_info 

/* 15 12 11 10

   1001 1100 0000 0000 */

#define DTC_IRQS 0x9c00

#endif /* else def HOSTS_C */

#endif /* ndef ASM */

#endif /* DTC3280_H */