| 1 |
1626 |
jcastillo |
/* esp.h: Defines and structures for the Sparc ESP (Enhanced SCSI
|
| 2 |
|
|
* Processor) driver under Linux.
|
| 3 |
|
|
*
|
| 4 |
|
|
* Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
|
| 5 |
|
|
*/
|
| 6 |
|
|
|
| 7 |
|
|
#ifndef _SPARC_ESP_H
|
| 8 |
|
|
#define _SPARC_ESP_H
|
| 9 |
|
|
|
| 10 |
|
|
/* For dvma controller register definitions. */
|
| 11 |
|
|
#include <asm/dma.h>
|
| 12 |
|
|
|
| 13 |
|
|
/* The ESP SCSI controllers have their register sets in three
|
| 14 |
|
|
* "classes":
|
| 15 |
|
|
*
|
| 16 |
|
|
* 1) Registers which are both read and write.
|
| 17 |
|
|
* 2) Registers which are read only.
|
| 18 |
|
|
* 3) Registers which are write only.
|
| 19 |
|
|
*
|
| 20 |
|
|
* Yet, they all live within the same IO space.
|
| 21 |
|
|
*/
|
| 22 |
|
|
|
| 23 |
|
|
/* All the ESP registers are one byte each and are accessed longwords
|
| 24 |
|
|
* apart with a big-endian ordering to the bytes.
|
| 25 |
|
|
*/
|
| 26 |
|
|
|
| 27 |
|
|
struct Sparc_ESP_regs {
|
| 28 |
|
|
/* Access Description Offset */
|
| 29 |
|
|
volatile unchar esp_tclow; /* rw Low bits of the transfer count 0x00 */
|
| 30 |
|
|
unchar tlpad1[3];
|
| 31 |
|
|
volatile unchar esp_tcmed; /* rw Mid bits of the transfer count 0x04 */
|
| 32 |
|
|
unchar fdpad[3];
|
| 33 |
|
|
volatile unchar esp_fdata; /* rw FIFO data bits 0x08 */
|
| 34 |
|
|
unchar cbpad[3];
|
| 35 |
|
|
volatile unchar esp_cmd; /* rw SCSI command bits 0x0c */
|
| 36 |
|
|
unchar stpad[3];
|
| 37 |
|
|
volatile unchar esp_status; /* ro ESP status register 0x10 */
|
| 38 |
|
|
#define esp_busid esp_status /* wo Bus ID for select/reselect 0x10 */
|
| 39 |
|
|
unchar irqpd[3];
|
| 40 |
|
|
volatile unchar esp_intrpt; /* ro Kind of interrupt 0x14 */
|
| 41 |
|
|
#define esp_timeo esp_intrpt /* wo Timeout value for select/resel 0x14 */
|
| 42 |
|
|
unchar sspad[3];
|
| 43 |
|
|
volatile unchar esp_sstep; /* ro Sequence step register 0x18 */
|
| 44 |
|
|
#define esp_stp esp_sstep /* wo Transfer period per sync 0x18 */
|
| 45 |
|
|
unchar ffpad[3];
|
| 46 |
|
|
volatile unchar esp_fflags; /* ro Bits of current FIFO info 0x1c */
|
| 47 |
|
|
#define esp_soff esp_fflags /* wo Sync offset 0x1c */
|
| 48 |
|
|
unchar cf1pd[3];
|
| 49 |
|
|
volatile unchar esp_cfg1; /* rw First configuration register 0x20 */
|
| 50 |
|
|
unchar cfpad[3];
|
| 51 |
|
|
volatile unchar esp_cfact; /* wo Clock conversion factor 0x24 */
|
| 52 |
|
|
unchar ctpad[3];
|
| 53 |
|
|
volatile unchar esp_ctest; /* wo Chip test register 0x28 */
|
| 54 |
|
|
unchar cf2pd[3];
|
| 55 |
|
|
volatile unchar esp_cfg2; /* rw Second configuration register 0x2c */
|
| 56 |
|
|
unchar cf3pd[3];
|
| 57 |
|
|
|
| 58 |
|
|
/* The following is only found on the 53C9X series SCSI chips */
|
| 59 |
|
|
volatile unchar esp_cfg3; /* rw Third configuration register 0x30 */
|
| 60 |
|
|
unchar thpd[7];
|
| 61 |
|
|
|
| 62 |
|
|
/* The following is found on all chips except the NCR53C90 (ESP100) */
|
| 63 |
|
|
volatile unchar esp_tchi; /* rw High bits of transfer count 0x38 */
|
| 64 |
|
|
#define esp_uid esp_tchi /* ro Unique ID code 0x38 */
|
| 65 |
|
|
unchar fgpad[3];
|
| 66 |
|
|
volatile unchar esp_fgrnd; /* rw Data base for fifo 0x3c */
|
| 67 |
|
|
};
|
| 68 |
|
|
|
| 69 |
|
|
/* Various revisions of the ESP board. */
|
| 70 |
|
|
enum esp_rev {
|
| 71 |
|
|
esp100 = 0x00, /* NCR53C90 */
|
| 72 |
|
|
esp100a = 0x01, /* NCR53C90A */
|
| 73 |
|
|
esp236 = 0x02,
|
| 74 |
|
|
fas236 = 0x03,
|
| 75 |
|
|
fas100a = 0x04,
|
| 76 |
|
|
fast = 0x05,
|
| 77 |
|
|
espunknown = 0x06
|
| 78 |
|
|
};
|
| 79 |
|
|
|
| 80 |
|
|
/* We get one of these for each ESP probed. */
|
| 81 |
|
|
struct Sparc_ESP {
|
| 82 |
|
|
struct Sparc_ESP *next; /* Next ESP on probed or NULL */
|
| 83 |
|
|
struct Sparc_ESP_regs *eregs; /* All esp registers */
|
| 84 |
|
|
struct Linux_SBus_DMA *dma; /* Who I do transfers with. */
|
| 85 |
|
|
struct sparc_dma_registers *dregs; /* And his registers. */
|
| 86 |
|
|
struct Scsi_Host *ehost; /* Backpointer to SCSI Host */
|
| 87 |
|
|
|
| 88 |
|
|
struct linux_sbus_device *edev; /* Pointer to SBus entry */
|
| 89 |
|
|
char prom_name[64]; /* Name of ESP device from prom */
|
| 90 |
|
|
int prom_node; /* Prom node where ESP found */
|
| 91 |
|
|
int esp_id; /* Same as esphost->host_id */
|
| 92 |
|
|
|
| 93 |
|
|
/* ESP Configuration Registers */
|
| 94 |
|
|
unsigned char config1; /* Copy of the 1st config register */
|
| 95 |
|
|
unsigned char config2; /* Copy of the 2nd config register */
|
| 96 |
|
|
unsigned char config3[8]; /* Copy of the 3rd config register */
|
| 97 |
|
|
|
| 98 |
|
|
/* The current command we are sending to the ESP chip. This esp_command
|
| 99 |
|
|
* ptr needs to be mapped in DVMA area so we can send commands and read
|
| 100 |
|
|
* from the ESP fifo without burning precious CPU cycles. Programmed I/O
|
| 101 |
|
|
* sucks when we have the DVMA to do it for us.
|
| 102 |
|
|
*/
|
| 103 |
|
|
volatile unchar *esp_command; /* Location of command */
|
| 104 |
|
|
int esp_clen; /* Length of this command */
|
| 105 |
|
|
|
| 106 |
|
|
/* To hold onto the dvma buffer ptr. */
|
| 107 |
|
|
char *dvma_hold;
|
| 108 |
|
|
|
| 109 |
|
|
/* The following are used to determine the cause of an IRQ. Upon every
|
| 110 |
|
|
* IRQ entry we synchronize these with the hardware registers.
|
| 111 |
|
|
*/
|
| 112 |
|
|
unchar ireg; /* Copy of ESP interrupt register */
|
| 113 |
|
|
unchar sreg; /* Same for ESP status register */
|
| 114 |
|
|
unchar seqreg; /* The ESP sequence register */
|
| 115 |
|
|
|
| 116 |
|
|
/* Clock periods, frequencies, synchronization, etc. */
|
| 117 |
|
|
unsigned int cfreq; /* Clock frequency in HZ */
|
| 118 |
|
|
unsigned int cfact; /* Clock conversion factor */
|
| 119 |
|
|
unsigned int ccycle; /* One ESP clock cycle */
|
| 120 |
|
|
unsigned int ctick; /* One ESP clock time */
|
| 121 |
|
|
unsigned int sync_defp; /* Default negotiation period */
|
| 122 |
|
|
|
| 123 |
|
|
/* Misc. info about this ESP */
|
| 124 |
|
|
enum esp_rev erev; /* ESP revision */
|
| 125 |
|
|
int irq; /* SBus IRQ for this ESP */
|
| 126 |
|
|
int scsi_id; /* Who am I as initiator? */
|
| 127 |
|
|
int scsi_id_mask; /* Bitmask of 'me'. */
|
| 128 |
|
|
int diff; /* Differential SCSI? */
|
| 129 |
|
|
int bursts; /* Burst sizes our DVMA supports */
|
| 130 |
|
|
|
| 131 |
|
|
/* Our command queues, only one cmd lives in the current_SC queue. */
|
| 132 |
|
|
Scsi_Cmnd *issue_SC; /* Commands to be issued */
|
| 133 |
|
|
Scsi_Cmnd *current_SC; /* Who is currently working the bus */
|
| 134 |
|
|
Scsi_Cmnd *disconnected_SC; /* Commands disconnected from the bus */
|
| 135 |
|
|
|
| 136 |
|
|
#ifdef THREADED_ESP_DRIVER
|
| 137 |
|
|
Scsi_Cmnd *eatme_SC; /* Cmds waiting for esp thread to process. */
|
| 138 |
|
|
#endif
|
| 139 |
|
|
|
| 140 |
|
|
/* Abortion status */
|
| 141 |
|
|
int aborting, abortion_complete, abort_result;
|
| 142 |
|
|
};
|
| 143 |
|
|
|
| 144 |
|
|
/* Bitfield meanings for the above registers. */
|
| 145 |
|
|
|
| 146 |
|
|
/* ESP config reg 1, read-write, found on all ESP chips */
|
| 147 |
|
|
#define ESP_CONFIG1_ID 0x07 /* My BUS ID bits */
|
| 148 |
|
|
#define ESP_CONFIG1_CHTEST 0x08 /* Enable ESP chip tests */
|
| 149 |
|
|
#define ESP_CONFIG1_PENABLE 0x10 /* Enable parity checks */
|
| 150 |
|
|
#define ESP_CONFIG1_PARTEST 0x20 /* Parity test mode enabled? */
|
| 151 |
|
|
#define ESP_CONFIG1_SRRDISAB 0x40 /* Disable SCSI reset reports */
|
| 152 |
|
|
#define ESP_CONFIG1_SLCABLE 0x80 /* Enable slow cable mode */
|
| 153 |
|
|
|
| 154 |
|
|
/* ESP config reg 2, read-write, found only on esp100a+esp200+esp236 chips */
|
| 155 |
|
|
#define ESP_CONFIG2_DMAPARITY 0x01 /* Parity DMA err (200,236) */
|
| 156 |
|
|
#define ESP_CONFIG2_REGPARITY 0x02 /* Parity reg err (200,236) */
|
| 157 |
|
|
#define ESP_CONFIG2_BADPARITY 0x04 /* Bad parity target abort */
|
| 158 |
|
|
#define ESP_CONFIG2_SCSI2ENAB 0x08 /* Enable SCSI-2 features */
|
| 159 |
|
|
#define ESP_CONFIG2_HI 0x10 /* High Impedance DREQ ??? */
|
| 160 |
|
|
#define ESP_CONFIG2_BCM 0x20 /* Enable byte-ctrl (236) */
|
| 161 |
|
|
#define ESP_CONFIG2_FENAB 0x40 /* Enable features (fas100,esp216) */
|
| 162 |
|
|
#define ESP_CONFIG2_SPL 0x40 /* Enable status-phase latch (esp236) */
|
| 163 |
|
|
#define ESP_CONFIG2_MAGIC 0xe0 /* Invalid bits... */
|
| 164 |
|
|
|
| 165 |
|
|
/* ESP config register 3 read-write, found only esp236+fas236+fas100a chips */
|
| 166 |
|
|
#define ESP_CONFIG3_FCLOCK 0x01 /* FAST SCSI clock rate (esp100a) */
|
| 167 |
|
|
#define ESP_CONFIG3_TEM 0x01 /* Enable thresh-8 mode (esp/fas236) */
|
| 168 |
|
|
#define ESP_CONFIG3_FAST 0x02 /* Enable FAST SCSI (esp100a) */
|
| 169 |
|
|
#define ESP_CONFIG3_ADMA 0x02 /* Enable alternate-dma (esp/fas236) */
|
| 170 |
|
|
#define ESP_CONFIG3_TENB 0x04 /* group2 SCSI2 support (esp100a) */
|
| 171 |
|
|
#define ESP_CONFIG3_SRB 0x04 /* Save residual byte (esp/fas236) */
|
| 172 |
|
|
#define ESP_CONFIG3_TMS 0x08 /* Three-byte msg's ok (esp100a) */
|
| 173 |
|
|
#define ESP_CONFIG3_FCLK 0x08 /* Fast SCSI clock rate (esp/fas236) */
|
| 174 |
|
|
#define ESP_CONFIG3_IDMSG 0x10 /* ID message checking (esp100a) */
|
| 175 |
|
|
#define ESP_CONFIG3_FSCSI 0x10 /* Enable FAST SCSI (esp/fas236) */
|
| 176 |
|
|
#define ESP_CONFIG3_GTM 0x20 /* group2 SCSI2 support (esp/fas236) */
|
| 177 |
|
|
#define ESP_CONFIG3_TBMS 0x40 /* Three-byte msg's ok (esp/fas236) */
|
| 178 |
|
|
#define ESP_CONFIG3_IMS 0x80 /* ID msg chk'ng (esp/fas236) */
|
| 179 |
|
|
|
| 180 |
|
|
/* ESP command register read-write */
|
| 181 |
|
|
/* Group 1 commands: These may be sent at any point in time to the ESP
|
| 182 |
|
|
* chip. None of them can generate interrupts 'cept
|
| 183 |
|
|
* the "SCSI bus reset" command if you have not disabled
|
| 184 |
|
|
* SCSI reset interrupts in the config1 ESP register.
|
| 185 |
|
|
*/
|
| 186 |
|
|
#define ESP_CMD_NULL 0x00 /* Null command, ie. a nop */
|
| 187 |
|
|
#define ESP_CMD_FLUSH 0x01 /* FIFO Flush */
|
| 188 |
|
|
#define ESP_CMD_RC 0x02 /* Chip reset */
|
| 189 |
|
|
#define ESP_CMD_RS 0x03 /* SCSI bus reset */
|
| 190 |
|
|
|
| 191 |
|
|
/* Group 2 commands: ESP must be an initiator and connected to a target
|
| 192 |
|
|
* for these commands to work.
|
| 193 |
|
|
*/
|
| 194 |
|
|
#define ESP_CMD_TI 0x10 /* Transfer Information */
|
| 195 |
|
|
#define ESP_CMD_ICCSEQ 0x11 /* Initiator cmd complete sequence */
|
| 196 |
|
|
#define ESP_CMD_MOK 0x12 /* Message okie-dokie */
|
| 197 |
|
|
#define ESP_CMD_TPAD 0x18 /* Transfer Pad */
|
| 198 |
|
|
#define ESP_CMD_SATN 0x1a /* Set ATN */
|
| 199 |
|
|
#define ESP_CMD_RATN 0x1b /* De-assert ATN */
|
| 200 |
|
|
|
| 201 |
|
|
/* Group 3 commands: ESP must be in the MSGOUT or MSGIN state and be connected
|
| 202 |
|
|
* to a target as the initiator for these commands to work.
|
| 203 |
|
|
*/
|
| 204 |
|
|
#define ESP_CMD_SMSG 0x20 /* Send message */
|
| 205 |
|
|
#define ESP_CMD_SSTAT 0x21 /* Send status */
|
| 206 |
|
|
#define ESP_CMD_SDATA 0x22 /* Send data */
|
| 207 |
|
|
#define ESP_CMD_DSEQ 0x23 /* Discontinue Sequence */
|
| 208 |
|
|
#define ESP_CMD_TSEQ 0x24 /* Terminate Sequence */
|
| 209 |
|
|
#define ESP_CMD_TCCSEQ 0x25 /* Target cmd cmplt sequence */
|
| 210 |
|
|
#define ESP_CMD_DCNCT 0x27 /* Disconnect */
|
| 211 |
|
|
#define ESP_CMD_RMSG 0x28 /* Receive Message */
|
| 212 |
|
|
#define ESP_CMD_RCMD 0x29 /* Receive Command */
|
| 213 |
|
|
#define ESP_CMD_RDATA 0x2a /* Receive Data */
|
| 214 |
|
|
#define ESP_CMD_RCSEQ 0x2b /* Receive cmd sequence */
|
| 215 |
|
|
|
| 216 |
|
|
/* Group 4 commands: The ESP must be in the disconnected state and must
|
| 217 |
|
|
* not be connected to any targets as initiator for
|
| 218 |
|
|
* these commands to work.
|
| 219 |
|
|
*/
|
| 220 |
|
|
#define ESP_CMD_RSEL 0x40 /* Reselect */
|
| 221 |
|
|
#define ESP_CMD_SEL 0x41 /* Select w/o ATN */
|
| 222 |
|
|
#define ESP_CMD_SELA 0x42 /* Select w/ATN */
|
| 223 |
|
|
#define ESP_CMD_SELAS 0x43 /* Select w/ATN & STOP */
|
| 224 |
|
|
#define ESP_CMD_ESEL 0x44 /* Enable selection */
|
| 225 |
|
|
#define ESP_CMD_DSEL 0x45 /* Disable selections */
|
| 226 |
|
|
#define ESP_CMD_SA3 0x46 /* Select w/ATN3 */
|
| 227 |
|
|
#define ESP_CMD_RSEL3 0x47 /* Reselect3 */
|
| 228 |
|
|
|
| 229 |
|
|
/* This bit enables the ESP's DMA on the SBus */
|
| 230 |
|
|
#define ESP_CMD_DMA 0x80 /* Do DMA? */
|
| 231 |
|
|
|
| 232 |
|
|
|
| 233 |
|
|
/* ESP status register read-only */
|
| 234 |
|
|
#define ESP_STAT_PIO 0x01 /* IO phase bit */
|
| 235 |
|
|
#define ESP_STAT_PCD 0x02 /* CD phase bit */
|
| 236 |
|
|
#define ESP_STAT_PMSG 0x04 /* MSG phase bit */
|
| 237 |
|
|
#define ESP_STAT_PMASK 0x07 /* Mask of phase bits */
|
| 238 |
|
|
#define ESP_STAT_TDONE 0x08 /* Transfer Completed */
|
| 239 |
|
|
#define ESP_STAT_TCNT 0x10 /* Transfer Counter Is Zero */
|
| 240 |
|
|
#define ESP_STAT_PERR 0x20 /* Parity error */
|
| 241 |
|
|
#define ESP_STAT_SPAM 0x40 /* Real bad error */
|
| 242 |
|
|
/* This indicates the 'interrupt pending' condition on esp236, it is a reserved
|
| 243 |
|
|
* bit on other revs of the ESP.
|
| 244 |
|
|
*/
|
| 245 |
|
|
#define ESP_STAT_INTR 0x80 /* Interrupt */
|
| 246 |
|
|
|
| 247 |
|
|
/* The status register can be masked with ESP_STAT_PMASK and compared
|
| 248 |
|
|
* with the following values to determine the current phase the ESP
|
| 249 |
|
|
* (at least thinks it) is in. For our purposes we also add our own
|
| 250 |
|
|
* software 'done' bit for our phase management engine.
|
| 251 |
|
|
*/
|
| 252 |
|
|
#define ESP_DOP (0) /* Data Out */
|
| 253 |
|
|
#define ESP_DIP (ESP_STAT_PIO) /* Data In */
|
| 254 |
|
|
#define ESP_CMDP (ESP_STAT_PCD) /* Command */
|
| 255 |
|
|
#define ESP_STATP (ESP_STAT_PCD|ESP_STAT_PIO) /* Status */
|
| 256 |
|
|
#define ESP_MOP (ESP_STAT_PMSG|ESP_STAT_PCD) /* Message Out */
|
| 257 |
|
|
#define ESP_MIP (ESP_STAT_PMSG|ESP_STAT_PCD|ESP_STAT_PIO) /* Message In */
|
| 258 |
|
|
|
| 259 |
|
|
/* ESP interrupt register read-only */
|
| 260 |
|
|
#define ESP_INTR_S 0x01 /* Select w/o ATN */
|
| 261 |
|
|
#define ESP_INTR_SATN 0x02 /* Select w/ATN */
|
| 262 |
|
|
#define ESP_INTR_RSEL 0x04 /* Reselected */
|
| 263 |
|
|
#define ESP_INTR_FDONE 0x08 /* Function done */
|
| 264 |
|
|
#define ESP_INTR_BSERV 0x10 /* Bus service */
|
| 265 |
|
|
#define ESP_INTR_DC 0x20 /* Disconnect */
|
| 266 |
|
|
#define ESP_INTR_IC 0x40 /* Illegal command given */
|
| 267 |
|
|
#define ESP_INTR_SR 0x80 /* SCSI bus reset detected */
|
| 268 |
|
|
|
| 269 |
|
|
/* Interrupt status macros */
|
| 270 |
|
|
#define ESP_SRESET_IRQ(esp) ((esp)->intreg & (ESP_INTR_SR))
|
| 271 |
|
|
#define ESP_ILLCMD_IRQ(esp) ((esp)->intreg & (ESP_INTR_IC))
|
| 272 |
|
|
#define ESP_SELECT_WITH_ATN_IRQ(esp) ((esp)->intreg & (ESP_INTR_SATN))
|
| 273 |
|
|
#define ESP_SELECT_WITHOUT_ATN_IRQ(esp) ((esp)->intreg & (ESP_INTR_S))
|
| 274 |
|
|
#define ESP_SELECTION_IRQ(esp) ((ESP_SELECT_WITH_ATN_IRQ(esp)) || \
|
| 275 |
|
|
(ESP_SELECT_WITHOUT_ATN_IRQ(esp)))
|
| 276 |
|
|
#define ESP_RESELECTION_IRQ(esp) ((esp)->intreg & (ESP_INTR_RSEL))
|
| 277 |
|
|
|
| 278 |
|
|
/* ESP sequence step register read-only */
|
| 279 |
|
|
#define ESP_STEP_VBITS 0x07 /* Valid bits */
|
| 280 |
|
|
#define ESP_STEP_ASEL 0x00 /* Selection&Arbitrate cmplt */
|
| 281 |
|
|
#define ESP_STEP_SID 0x01 /* One msg byte sent */
|
| 282 |
|
|
#define ESP_STEP_NCMD 0x02 /* Was not in command phase */
|
| 283 |
|
|
#define ESP_STEP_PPC 0x03 /* Early phase chg caused cmnd
|
| 284 |
|
|
* bytes to be lost
|
| 285 |
|
|
*/
|
| 286 |
|
|
#define ESP_STEP_FINI 0x04 /* Command was sent ok */
|
| 287 |
|
|
|
| 288 |
|
|
/* ESP chip-test register read-write */
|
| 289 |
|
|
#define ESP_TEST_TARG 0x01 /* Target test mode */
|
| 290 |
|
|
#define ESP_TEST_INI 0x02 /* Initiator test mode */
|
| 291 |
|
|
#define ESP_TEST_TS 0x04 /* Tristate test mode */
|
| 292 |
|
|
|
| 293 |
|
|
/* ESP unique ID register read-only, found on fas236+fas100a only */
|
| 294 |
|
|
#define ESP_UID_F100A 0x00 /* ESP FAS100A */
|
| 295 |
|
|
#define ESP_UID_F236 0x02 /* ESP FAS236 */
|
| 296 |
|
|
#define ESP_UID_REV 0x07 /* ESP revision */
|
| 297 |
|
|
#define ESP_UID_FAM 0xf8 /* ESP family */
|
| 298 |
|
|
|
| 299 |
|
|
/* ESP fifo flags register read-only */
|
| 300 |
|
|
/* Note that the following implies a 16 byte FIFO on the ESP. */
|
| 301 |
|
|
#define ESP_FF_FBYTES 0x1f /* Num bytes in FIFO */
|
| 302 |
|
|
#define ESP_FF_SSTEP 0xe0 /* Sequence step */
|
| 303 |
|
|
|
| 304 |
|
|
/* ESP clock conversion factor register write-only */
|
| 305 |
|
|
#define ESP_CCF_F0 0x00 /* 35.01MHz - 40MHz */
|
| 306 |
|
|
#define ESP_CCF_NEVER 0x01 /* Set it to this and die */
|
| 307 |
|
|
#define ESP_CCF_F2 0x02 /* 10MHz */
|
| 308 |
|
|
#define ESP_CCF_F3 0x03 /* 10.01MHz - 15MHz */
|
| 309 |
|
|
#define ESP_CCF_F4 0x04 /* 15.01MHz - 20MHz */
|
| 310 |
|
|
#define ESP_CCF_F5 0x05 /* 20.01MHz - 25MHz */
|
| 311 |
|
|
#define ESP_CCF_F6 0x06 /* 25.01MHz - 30MHz */
|
| 312 |
|
|
#define ESP_CCF_F7 0x07 /* 30.01MHz - 35MHz */
|
| 313 |
|
|
|
| 314 |
|
|
extern int esp_detect(struct SHT *);
|
| 315 |
|
|
extern const char *esp_info(struct Scsi_Host *);
|
| 316 |
|
|
extern int esp_queue(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
|
| 317 |
|
|
extern int esp_command(Scsi_Cmnd *);
|
| 318 |
|
|
extern int esp_abort(Scsi_Cmnd *);
|
| 319 |
|
|
extern int esp_reset(Scsi_Cmnd *, unsigned int);
|
| 320 |
|
|
|
| 321 |
|
|
extern struct proc_dir_entry proc_scsi_esp;
|
| 322 |
|
|
|
| 323 |
|
|
#define SCSI_SPARC_ESP { \
|
| 324 |
|
|
/* struct SHT *next */ NULL, \
|
| 325 |
|
|
/* long *usage_count */ NULL, \
|
| 326 |
|
|
/* struct proc_dir_entry *proc_dir */ &proc_scsi_esp, \
|
| 327 |
|
|
/* int (*proc_info)(char *, char **, off_t, int, int, int) */ NULL, \
|
| 328 |
|
|
/* const char *name */ "Sun ESP 100/100a/200", \
|
| 329 |
|
|
/* int detect(struct SHT *) */ esp_detect, \
|
| 330 |
|
|
/* int release(struct Scsi_Host *) */ NULL, \
|
| 331 |
|
|
/* const char *info(struct Scsi_Host *) */ esp_info, \
|
| 332 |
|
|
/* int command(Scsi_Cmnd *) */ esp_command, \
|
| 333 |
|
|
/* int queuecommand(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *)) */ esp_queue, \
|
| 334 |
|
|
/* int abort(Scsi_Cmnd *) */ esp_abort, \
|
| 335 |
|
|
/* int reset(Scsi_Cmnd *, int) */ esp_reset, \
|
| 336 |
|
|
/* int slave_attach(int, int) */ NULL, \
|
| 337 |
|
|
/* int bios_param(Disk *, kdev_t, int[]) */ NULL, \
|
| 338 |
|
|
/* int can_queue */ 10, \
|
| 339 |
|
|
/* int this_id */ 7, \
|
| 340 |
|
|
/* short unsigned int sg_tablesize */ SG_ALL, \
|
| 341 |
|
|
/* short cmd_per_lun */ 1, \
|
| 342 |
|
|
/* unsigned char present */ 0, \
|
| 343 |
|
|
/* unsigned unchecked_isa_dma:1 */ 0, \
|
| 344 |
|
|
/* unsigned use_clustering:1 */ DISABLE_CLUSTERING, }
|
| 345 |
|
|
|
| 346 |
|
|
/* For our interrupt engine. */
|
| 347 |
|
|
#define for_each_esp(esp) \
|
| 348 |
|
|
for((esp) = espchain; (esp); (esp) = (esp)->next)
|
| 349 |
|
|
|
| 350 |
|
|
#endif /* !(_SPARC_ESP_H) */
|
