Subversion Repositories or1k

/*

 * Generic Generic NCR5380 driver

 *

 * Copyright 1993, Drew Eckhardt

 *      Visionary Computing

 *      (Unix and Linux consulting and custom programming)

 *      drew@colorado.edu

 *      +1 (303) 440-4894

 *

 * NCR53C400 extensions (c) 1994,1995,1996, Kevin Lentin

 *    K.Lentin@cs.monash.edu.au

 *

 * ALPHA RELEASE 1.

 *

 * For more information, please consult

 *

 * NCR 5380 Family

 * SCSI Protocol Controller

 * Databook

 *

 * NCR Microelectronics

 * 1635 Aeroplaza Drive

 * Colorado Springs, CO 80916

 * 1+ (719) 578-3400

 * 1+ (800) 334-5454

 */

/*

 * TODO : flesh out DMA support, find some one actually using this (I have

 *      a memory mapped Trantor board that works fine)

 */

/*

 * Options :

 *

 * PARITY - enable parity checking.  Not supported.

 *

 * SCSI2 - enable support for SCSI-II tagged queueing.  Untested.

 *

 * USLEEP - enable support for devices that don't disconnect.  Untested.

 *

 * The card is detected and initialized in one of several ways :

 * 1.  With command line overrides - NCR5380=port,irq may be

 *     used on the LILO command line to override the defaults.

 *

 * 2.  With the GENERIC_NCR5380_OVERRIDE compile time define.  This is

 *     specified as an array of address, irq, dma, board tuples.  Ie, for

 *     one board at 0x350, IRQ5, no dma, I could say

 *     -DGENERIC_NCR5380_OVERRIDE={{0xcc000, 5, DMA_NONE, BOARD_NCR5380}}

 *

 * -1 should be specified for no or DMA interrupt, -2 to autoprobe for an

 *      IRQ line if overridden on the command line.

 *

 * 3.  When included as a module, with arguments passed on the command line:

 *         ncr_irq=xx   the interrupt

 *         ncr_addr=xx  the port or base address (for port or memory

 *                      mapped, resp.)

 *         ncr_dma=xx   the DMA

 *         ncr_5380=1   to set up for a NCR5380 board

 *         ncr_53c400=1 to set up for a NCR53C400 board

 *     e.g.

 *     modprobe g_NCR5380 ncr_irq=5 ncr_addr=0x350 ncr_5380=1

 *       for a port mapped NCR5380 board or

 *     modprobe g_NCR5380 ncr_irq=255 ncr_addr=0xc8000 ncr_53c400=1

 *       for a memory mapped NCR53C400 board with interrupts disabled.

 *

 * 255 should be specified for no or DMA interrupt, 254 to autoprobe for an

 *      IRQ line if overridden on the command line.

 *

 */

/*

 * $Log: not supported by cvs2svn $

 * Revision 1.1.1.1  2001/09/10 07:44:32  simons

 * Initial import

 *

 * Revision 1.1.1.1  2001/07/02 17:58:27  simons

 * Initial revision

 *

 */

#define AUTOPROBE_IRQ

#define AUTOSENSE

#include <linux/config.h>

#ifdef CONFIG_SCSI_GENERIC_NCR53C400

#define NCR53C400_PSEUDO_DMA 1

#define PSEUDO_DMA

#define NCR53C400

#define NCR5380_STATS

#undef NCR5380_STAT_LIMIT

#endif

#if defined(CONFIG_SCSI_G_NCR5380_PORT) && defined(CONFIG_SCSI_G_NCR5380_MEM)

#error You can not configure the Generic NCR 5380 SCSI Driver for memory mapped I/O and port mapped I/O at the same time (yet)

#endif

#if !defined(CONFIG_SCSI_G_NCR5380_PORT) && !defined(CONFIG_SCSI_G_NCR5380_MEM)

#error You must configure the Generic NCR 5380 SCSI Driver for one of memory mapped I/O and port mapped I/O.

#endif

#include <asm/system.h>

#include <asm/io.h>

#include <linux/signal.h>

#include <linux/sched.h>

#include <linux/blk.h>

#include "scsi.h"

#include "hosts.h"

#include "g_NCR5380.h"

#include "NCR5380.h"

#include "constants.h"

#include "sd.h"

#include<linux/stat.h>

struct proc_dir_entry proc_scsi_g_ncr5380 = {

    PROC_SCSI_GENERIC_NCR5380, 9, "g_NCR5380",

    S_IFDIR | S_IRUGO | S_IXUGO, 2

};

#define NCR_NOT_SET 0

static int ncr_irq=NCR_NOT_SET;

static int ncr_dma=NCR_NOT_SET;

static int ncr_addr=NCR_NOT_SET;

static int ncr_5380=NCR_NOT_SET;

static int ncr_53c400=NCR_NOT_SET;

static struct override {

        NCR5380_implementation_fields;

    int irq;

    int dma;

    int board;  /* Use NCR53c400, Ricoh, etc. extensions ? */

} overrides

#ifdef GENERIC_NCR5380_OVERRIDE 

    [] = GENERIC_NCR5380_OVERRIDE

#else

    [1] = {{0,},};

#endif

#define NO_OVERRIDES (sizeof(overrides) / sizeof(struct override))

/*

 * Function : static internal_setup(int board, char *str, int *ints)

 *

 * Purpose : LILO command line initialization of the overrides array,

 *

 * Inputs : board - either BOARD_NCR5380 for a normal NCR5380 board,

 *      or BOARD_NCR53C400 for a NCR53C400 board. str - unused, ints -

 *      array of integer parameters with ints[0] equal to the number of ints.

 *

 */

static void internal_setup(int board, char *str, int *ints) {

    static int commandline_current = 0;

    switch (board) {

    case BOARD_NCR5380:

        if (ints[0] != 2 && ints[0] != 3) {

            printk("generic_NCR5380_setup : usage ncr5380=" STRVAL(NCR5380_map_name) ",irq,dma\n");

            return;

        }

    case BOARD_NCR53C400:

        if (ints[0] != 2) {

            printk("generic_NCR53C400_setup : usage ncr53c400=" STRVAL(NCR5380_map_name) ",irq\n");

            return;

        }

    }

    if (commandline_current < NO_OVERRIDES) {

        overrides[commandline_current].NCR5380_map_name = (NCR5380_map_type)ints[1];

        overrides[commandline_current].irq = ints[2];

        if (ints[0] == 3)

            overrides[commandline_current].dma = ints[3];

        else

            overrides[commandline_current].dma = DMA_NONE;

        overrides[commandline_current].board = board;

            ++commandline_current;

    }

}

/*

 * Function : generic_NCR5380_setup (char *str, int *ints)

 *

 * Purpose : LILO command line initialization of the overrides array,

 *

 * Inputs : str - unused, ints - array of integer parameters with ints[0]

 *      equal to the number of ints.

 */

void generic_NCR5380_setup (char *str, int *ints) {

    internal_setup (BOARD_NCR5380, str, ints);

}

/*

 * Function : generic_NCR53C400_setup (char *str, int *ints)

 *

 * Purpose : LILO command line initialization of the overrides array,

 *

 * Inputs : str - unused, ints - array of integer parameters with ints[0]

 *      equal to the number of ints.

 */

void generic_NCR53C400_setup (char *str, int *ints) {

    internal_setup (BOARD_NCR53C400, str, ints);

}

/*

 * Function : int generic_NCR5380_detect(Scsi_Host_Template * tpnt)

 *

 * Purpose : initializes generic NCR5380 driver based on the

 *      command line / compile time port and irq definitions.

 *

 * Inputs : tpnt - template for this SCSI adapter.

 *

 * Returns : 1 if a host adapter was found, 0 if not.

 *

 */

int generic_NCR5380_detect(Scsi_Host_Template * tpnt) {

    static int current_override = 0;

    int count;

    int flags = 0;

    struct Scsi_Host *instance;

    if (ncr_irq != NCR_NOT_SET)

        overrides[0].irq=ncr_irq;

    if (ncr_dma != NCR_NOT_SET)

        overrides[0].dma=ncr_dma;

    if (ncr_addr != NCR_NOT_SET)

        overrides[0].NCR5380_map_name=(NCR5380_map_type)ncr_addr;

    if (ncr_5380 != NCR_NOT_SET)

        overrides[0].board=BOARD_NCR5380;

    else if (ncr_53c400 != NCR_NOT_SET)

        overrides[0].board=BOARD_NCR53C400;

    tpnt->proc_dir = &proc_scsi_g_ncr5380;

    for (count = 0; current_override < NO_OVERRIDES; ++current_override) {

        if (!(overrides[current_override].NCR5380_map_name))

            continue;

        switch (overrides[current_override].board) {

        case BOARD_NCR5380:

            flags = FLAG_NO_PSEUDO_DMA;

            break;

        case BOARD_NCR53C400:

            flags = FLAG_NCR53C400;

            break;

        }

        instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));

        instance->NCR5380_instance_name = overrides[current_override].NCR5380_map_name;

        NCR5380_init(instance, flags);

        if (overrides[current_override].irq != IRQ_AUTO)

            instance->irq = overrides[current_override].irq;

        else

            instance->irq = NCR5380_probe_irq(instance, 0xffff);

        if (instance->irq != IRQ_NONE)

            if (request_irq(instance->irq, generic_NCR5380_intr, SA_INTERRUPT, "NCR5380", NULL)) {

                printk("scsi%d : IRQ%d not free, interrupts disabled\n",

                    instance->host_no, instance->irq);

                instance->irq = IRQ_NONE;

            }

        if (instance->irq == IRQ_NONE) {

            printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);

            printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);

        }

        printk("scsi%d : at " STRVAL(NCR5380_map_name) " 0x%x", instance->host_no, (unsigned int)instance->NCR5380_instance_name);

        if (instance->irq == IRQ_NONE)

            printk (" interrupts disabled");

        else

            printk (" irq %d", instance->irq);

        printk(" options CAN_QUEUE=%d  CMD_PER_LUN=%d release=%d",

            CAN_QUEUE, CMD_PER_LUN, GENERIC_NCR5380_PUBLIC_RELEASE);

        NCR5380_print_options(instance);

        printk("\n");

        ++current_override;

        ++count;

    }

    return count;

}

const char * generic_NCR5380_info (struct Scsi_Host* host) {

    static const char string[]="Generic NCR5380/53C400 Driver";

    return string;

}

int generic_NCR5380_release_resources(struct Scsi_Host * instance)

{

    NCR5380_local_declare();

    NCR5380_setup(instance);

    if (instance->irq != IRQ_NONE)

        free_irq(instance->irq, NULL);

        return 0;

}

#ifdef BIOSPARAM

/*

 * Function : int generic_NCR5380_biosparam(Disk * disk, kdev_t dev, int *ip)

 *

 * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for

 *      the specified device / size.

 *

 * Inputs : size = size of device in sectors (512 bytes), dev = block device

 *      major / minor, ip[] = {heads, sectors, cylinders}

 *

 * Returns : always 0 (success), initializes ip

 *

 */

/*

 * XXX Most SCSI boards use this mapping, I could be incorrect.  Some one

 * using hard disks on a trantor should verify that this mapping corresponds

 * to that used by the BIOS / ASPI driver by running the linux fdisk program

 * and matching the H_C_S coordinates to what DOS uses.

 */

int generic_NCR5380_biosparam(Disk * disk, kdev_t dev, int *ip)

{

  int size = disk->capacity;

  ip[0] = 64;

  ip[1] = 32;

  ip[2] = size >> 11;

  return 0;

}

#endif

#if NCR53C400_PSEUDO_DMA

static inline int NCR5380_pread (struct Scsi_Host *instance, unsigned char *dst,    int len)

{

    int blocks = len / 128;

    int start = 0;

    int i;

    int bl;

    NCR5380_local_declare();

    NCR5380_setup(instance);

#if (NDEBUG & NDEBUG_C400_PREAD)

    printk("53C400r: About to read %d blocks for %d bytes\n", blocks, len);

#endif

    NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE | CSR_TRANS_DIR);

    NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);

    while (1) {

#if (NDEBUG & NDEBUG_C400_PREAD)

        printk("53C400r: %d blocks left\n", blocks);

#endif

        if ((bl=NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {

#if (NDEBUG & NDEBUG_C400_PREAD)

            if (blocks)

                printk("53C400r: blocks still == %d\n", blocks);

            else

                printk("53C400r: Exiting loop\n");

#endif

            break;

        }

#if 1

        if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {

            printk("53C400r: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);

            return -1;

        }

#endif

#if (NDEBUG & NDEBUG_C400_PREAD)

        printk("53C400r: Waiting for buffer, bl=%d\n", bl);

#endif

        while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)

            ;

#if (NDEBUG & NDEBUG_C400_PREAD)

        printk("53C400r: Transferring 128 bytes\n");

#endif

#ifdef CONFIG_SCSI_G_NCR5380_PORT

        for (i=0; i<128; i++)

            dst[start+i] = NCR5380_read(C400_HOST_BUFFER);

#else

        /* implies CONFIG_SCSI_G_NCR5380_MEM */

        memmove(dst+start,NCR53C400_host_buffer+NCR5380_map_name,128);

#endif

        start+=128;

        blocks--;

    }

    if (blocks) {

#if (NDEBUG & NDEBUG_C400_PREAD)

        printk("53C400r: EXTRA: Waiting for buffer\n");

#endif

        while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)

            ;

#if (NDEBUG & NDEBUG_C400_PREAD)

        printk("53C400r: Transferring EXTRA 128 bytes\n");

#endif

#ifdef CONFIG_SCSI_G_NCR5380_PORT

        for (i=0; i<128; i++)

            dst[start+i] = NCR5380_read(C400_HOST_BUFFER);

#else

        /* implies CONFIG_SCSI_G_NCR5380_MEM */

        memmove(dst+start,NCR53C400_host_buffer+NCR5380_map_name,128);

#endif

        start+=128;

        blocks--;

    }

#if (NDEBUG & NDEBUG_C400_PREAD)

    else

        printk("53C400r: No EXTRA required\n");

#endif

#if (NDEBUG & NDEBUG_C400_PREAD)

    printk("53C400r: Final values: blocks=%d   start=%d\n", blocks, start);

#endif

    if (!(NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))

        printk("53C400r: no 53C80 gated irq after transfer");

#if (NDEBUG & NDEBUG_C400_PREAD)

    else

        printk("53C400r: Got 53C80 interrupt and tried to clear it\n");

#endif

/* DON'T DO THIS - THEY NEVER ARRIVE!

    printk("53C400r: Waiting for 53C80 registers\n");

    while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG)

        ;

*/

    if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER))

        printk("53C400r: no end dma signal\n");

#if (NDEBUG & NDEBUG_C400_PREAD)

    else

        printk("53C400r: end dma as expected\n");

#endif

    NCR5380_write(MODE_REG, MR_BASE);

    NCR5380_read(RESET_PARITY_INTERRUPT_REG);

    return 0;

}

static inline int NCR5380_pwrite (struct Scsi_Host *instance, unsigned char *src,    int len)

{

    int blocks = len / 128;

    int start = 0;

    int i;

    int bl;

    NCR5380_local_declare();

    NCR5380_setup(instance);

#if (NDEBUG & NDEBUG_C400_PWRITE)

    printk("53C400w: About to write %d blocks for %d bytes\n", blocks, len);

#endif

    NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE);

    NCR5380_write(C400_BLOCK_COUNTER_REG, blocks);

    while (1) {

        if (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ) {

            printk("53C400w: Got 53C80_IRQ start=%d, blocks=%d\n", start, blocks);

            return -1;

        }

        if ((bl=NCR5380_read(C400_BLOCK_COUNTER_REG)) == 0) {

#if (NDEBUG & NDEBUG_C400_PWRITE)

            if (blocks)

                printk("53C400w: exiting loop, blocks still == %d\n", blocks);

            else

                printk("53C400w: exiting loop\n");

#endif

            break;

        }

#if (NDEBUG & NDEBUG_C400_PWRITE)

        printk("53C400w: %d blocks left\n", blocks);

        printk("53C400w: waiting for buffer, bl=%d\n", bl);

#endif

        while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)

            ;

#if (NDEBUG & NDEBUG_C400_PWRITE)

        printk("53C400w: transferring 128 bytes\n");

#endif

#ifdef CONFIG_SCSI_G_NCR5380_PORT

        for (i=0; i<128; i++)

            NCR5380_write(C400_HOST_BUFFER, src[start+i]);

#else

        /* implies CONFIG_SCSI_G_NCR5380_MEM */

        memmove(NCR53C400_host_buffer+NCR5380_map_name,src+start,128);

#endif

        start+=128;

        blocks--;

    }

    if (blocks) {

#if (NDEBUG & NDEBUG_C400_PWRITE)

        printk("53C400w: EXTRA waiting for buffer\n");

#endif

        while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_HOST_BUF_NOT_RDY)

            ;

#if (NDEBUG & NDEBUG_C400_PWRITE)

        printk("53C400w: transferring EXTRA 128 bytes\n");

#endif

#ifdef CONFIG_SCSI_G_NCR5380_PORT

        for (i=0; i<128; i++)

            NCR5380_write(C400_HOST_BUFFER, src[start+i]);

#else

        /* implies CONFIG_SCSI_G_NCR5380_MEM */

        memmove(NCR53C400_host_buffer+NCR5380_map_name,src+start,128);

#endif

        start+=128;

        blocks--;

    }

#if (NDEBUG & NDEBUG_C400_PWRITE)

    else

        printk("53C400w: No EXTRA required\n");

#endif

#if (NDEBUG & NDEBUG_C400_PWRITE)

    printk("53C400w: Final values: blocks=%d   start=%d\n", blocks, start);

#endif

#if 0

    printk("53C400w: waiting for registers to be available\n");

    THEY NEVER DO!

    while (NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_53C80_REG)

        ;

    printk("53C400w: Got em\n");

#endif

    /* Let's wait for this instead - could be ugly */

    /* All documentation says to check for this. Maybe my hardware is too

     * fast. Waiting for it seems to work fine! KLL

     */

    while (!(i = NCR5380_read(C400_CONTROL_STATUS_REG) & CSR_GATED_53C80_IRQ))

        ;

    /*

     * I know. i is certainly != 0 here but the loop is new. See previous

     * comment.

     */

    if (i) {

#if (NDEBUG & NDEBUG_C400_PWRITE)

        printk("53C400w: got 53C80 gated irq (last block)\n");

#endif

        if (!((i=NCR5380_read(BUS_AND_STATUS_REG)) & BASR_END_DMA_TRANSFER))

            printk("53C400w: No END OF DMA bit - WHOOPS! BASR=%0x\n",i);

#if (NDEBUG & NDEBUG_C400_PWRITE)

        else

            printk("53C400w: Got END OF DMA\n");

#endif

    }

    else

        printk("53C400w: no 53C80 gated irq after transfer (last block)\n");

#if 0

    if (!(NCR5380_read(BUS_AND_STATUS_REG) & BASR_END_DMA_TRANSFER)) {

        printk("53C400w: no end dma signal\n");

    }

#endif

#if (NDEBUG & NDEBUG_C400_PWRITE)

    printk("53C400w: waiting for last byte...\n");

#endif

    while (!(NCR5380_read(TARGET_COMMAND_REG) & TCR_LAST_BYTE_SENT))

        ;

#if (NDEBUG & NDEBUG_C400_PWRITE)

    printk("53C400w:     got last byte.\n");

    printk("53C400w: pwrite exiting with status 0, whoopee!\n");

#endif

    return 0;

}

#endif /* PSEUDO_DMA */

#include "NCR5380.c"

#define PRINTP(x) len += sprintf(buffer+len, x)

#define ANDP ,

static int sprint_opcode(char* buffer, int len, int opcode) {

    int start = len;

    PRINTP("0x%02x " ANDP opcode);

    return len-start;

}

static int sprint_command (char* buffer, int len, unsigned char *command) {

    int i,s,start=len;

    len += sprint_opcode(buffer, len, command[0]);

    for ( i = 1, s = COMMAND_SIZE(command[0]); i < s; ++i)

        PRINTP("%02x " ANDP command[i]);

    PRINTP("\n");

    return len-start;

}

static int sprint_Scsi_Cmnd (char* buffer, int len, Scsi_Cmnd *cmd) {

    int start = len;

    PRINTP("host number %d destination target %d, lun %d\n" ANDP

       cmd->host->host_no ANDP

       cmd->target ANDP

       cmd->lun);

    PRINTP("        command = ");

    len += sprint_command (buffer, len, cmd->cmnd);

    return len-start;

}

int generic_NCR5380_proc_info(char* buffer, char** start, off_t offset, int length, int hostno, int inout)

{

    int len = 0;

    NCR5380_local_declare();

    unsigned char status;

    int i;

    struct Scsi_Host *scsi_ptr;

    Scsi_Cmnd *ptr;

    Scsi_Device *dev;

    struct NCR5380_hostdata *hostdata;

    cli();

    for (scsi_ptr = first_instance; scsi_ptr; scsi_ptr=scsi_ptr->next)

        if (scsi_ptr->host_no == hostno)

            break;

    NCR5380_setup(scsi_ptr);

    hostdata = (struct NCR5380_hostdata *)scsi_ptr->hostdata;

    PRINTP("SCSI host number %d : %s\n" ANDP scsi_ptr->host_no ANDP scsi_ptr->hostt->name);

    PRINTP("Generic NCR5380 driver version %d\n" ANDP GENERIC_NCR5380_PUBLIC_RELEASE);

    PRINTP("NCR5380 core version %d\n" ANDP NCR5380_PUBLIC_RELEASE);

#ifdef NCR53C400

    PRINTP("NCR53C400 extension version %d\n" ANDP NCR53C400_PUBLIC_RELEASE);

    PRINTP("NCR53C400 card%s detected\n" ANDP  (((struct NCR5380_hostdata *)scsi_ptr->hostdata)->flags & FLAG_NCR53C400)?"":" not");

# if NCR53C400_PSEUDO_DMA

    PRINTP("NCR53C400 pseudo DMA used\n");

# endif

#else

    PRINTP("NO NCR53C400 driver extensions\n");

#endif

    PRINTP("Using %s mapping at %s 0x%x, " ANDP STRVAL(NCR5380_map_config) ANDP STRVAL(NCR5380_map_name) ANDP scsi_ptr->NCR5380_instance_name);

    if (scsi_ptr->irq == IRQ_NONE)

        PRINTP("no interrupt\n");

    else

        PRINTP("on interrupt %d\n" ANDP scsi_ptr->irq);

#ifdef NCR5380_STATS

    if (hostdata->connected || hostdata->issue_queue || hostdata->disconnected_queue)

        PRINTP("There are commands pending, transfer rates may be crud\n");

    if (hostdata->pendingr)

        PRINTP("  %d pending reads" ANDP hostdata->pendingr);

    if (hostdata->pendingw)

        PRINTP("  %d pending writes" ANDP hostdata->pendingw);

    if (hostdata->pendingr || hostdata->pendingw)

        PRINTP("\n");

    for (dev = scsi_devices; dev; dev=dev->next) {

        if (dev->host == scsi_ptr) {

            unsigned long br = hostdata->bytes_read[dev->id];

            unsigned long bw = hostdata->bytes_write[dev->id];

            long tr = hostdata->time_read[dev->id] / HZ;

            long tw = hostdata->time_write[dev->id] / HZ;

            PRINTP("  T:%d %s " ANDP dev->id ANDP (dev->type < MAX_SCSI_DEVICE_CODE) ? scsi_device_types[(int)dev->type] : "Unknown");

            for (i=0; i<8; i++)

                if (dev->vendor[i] >= 0x20)

                    *(buffer+(len++)) = dev->vendor[i];

            *(buffer+(len++)) = ' ';

            for (i=0; i<16; i++)

                if (dev->model[i] >= 0x20)

                    *(buffer+(len++)) = dev->model[i];

            *(buffer+(len++)) = ' ';

            for (i=0; i<4; i++)

                if (dev->rev[i] >= 0x20)

                    *(buffer+(len++)) = dev->rev[i];

            *(buffer+(len++)) = ' ';

            PRINTP("\n%10ld kb read    in %5ld secs" ANDP br/1024 ANDP tr);

            if (tr)