Subversion Repositories or1k

/*

 *-------------------------------------------------------------------

 *

 *   QSM -- Queued Serial Module

 *

 * The QSM contains two serial interfaces: (a) the queued serial

 * peripheral interface (QSPI) and the serial communication interface

 * (SCI). The QSPI provides peripheral expansion and/or interprocessor

 * communication through a full-duplex, synchronous, three-wire bus. A

 * self contained RAM queue permits serial data transfers without CPU

 * intervention and automatic continuous sampling. The SCI provides a

 * standard non-return to zero mark/space format with wakeup functions

 * to allow the CPU to run uninterrupted until woken

 *

 * For more information, refer to Motorola's "Modular Microcontroller

 * Family Queued Serial Module Reference Manual" (Motorola document

 * QSMRM/AD).

 *

 * This file has been created by John S. Gwynne for support of

 * Motorola's 68332 MCU in the efi332 project.

 *

 * Redistribution and use in source and binary forms are permitted

 * provided that the following conditions are met:

 * 1. Redistribution of source code and documentation must retain

 *    the above authorship, this list of conditions and the

 *    following disclaimer.

 * 2. The name of the author may not be used to endorse or promote

 *    products derived from this software without specific prior

 *    written permission.

 *

 * This software is provided "AS IS" without warranty of any kind,

 * either expressed or implied, including, but not limited to, the

 * implied warranties of merchantability, title and fitness for a

 * particular purpose.

 *

 *------------------------------------------------------------------

 *

 *  $Id: qsm.h,v 1.1.1.1 2001-07-10 09:45:05 chris Exp $

 */

#ifndef _QSM_H_

#define _QSM_H_

/* SAM-- shift and mask */

#undef  SAM

#define SAM(a,b,c) ((a << b) & c)

/* QSM_CRB (QSM Control Register Block) base address of the QSM

   control registers */

#if SIM_MM == 0

#define QSM_CRB 0x7ffc00

#else

#undef SIM_MM

#define SIM_MM 1

#define QSM_CRB 0xfffc00

#endif 

#define QSMCR (volatile unsigned short int * const)(0x00 + QSM_CRB)

                                /* QSM Configuration Register */

#define    STOP 0x8000          /*    Stop Enable */

#define    FRZ  0x6000          /*    Freeze Control */

#define    SUPV 0x0080          /*    Supervisor/Unrestricted */

#define    IARB 0x000f          /*    Inerrupt Arbitration */

#define QTEST (volatile unsigned short int * const)(0x02 + QSM_CRB)

                                /* QSM Test Register */

/* Used only for factor testing */

#define QILR (volatile unsigned char * const)(0x04 + QSM_CRB)

                                /* QSM Interrupt Level Register */

#define    ILQSPI 0x38          /*    Interrupt Level for QSPI */

#define    ILSCI  0x07          /*    Interrupt Level for SCI */

#define QIVR (volatile unsigned char * const)(0x05 + QSM_CRB)

                                /* QSM Interrupt Vector Register */

#define    INTV   0xff          /*    Interrupt Vector Number */

#define SCCR0 (volatile unsigned short int * const)(0x08 + QSM_CRB)

                                /* SCI Control Register 0 */

#define    SCBR   0x1fff        /*    SCI Baud Rate */

#define SCCR1 (volatile unsigned short int * const)(0x0a + QSM_CRB)

                                /* SCI Control Register 1 */

#define    LOOPS  0x4000        /*    Loop Mode */

#define    WOMS   0x2000        /*    Wired-OR Mode for SCI Pins */

#define    ILT    0x1000        /*    Idle-Line Detect Type */

#define    PT     0x0800        /*    Parity Type */

#define    PE     0x0400        /*    Parity Enable */

#define    M      0x0200        /*    Mode Select */

#define    WAKE   0x0100        /*    Wakeup by Address Mark */

#define    TIE    0x0080        /*    Transmit Complete Interrupt Enable */

#define    TCIE   0x0040        /*    Transmit Complete Interrupt Enable */

#define    RIE    0x0020        /*    Receiver Interrupt Enable */

#define    ILIE   0x0010        /*    Idle-Line Interrupt Enable */

#define    TE     0x0008        /*    Transmitter Enable */

#define    RE     0x0004        /*    Receiver Enable */

#define    RWU    0x0002        /*    Receiver Wakeup */

#define    SBK    0x0001        /*    Send Break */

#define SCSR (volatile unsigned short int * const)(0x0c + QSM_CRB)

                                /* SCI Status Register */

#define    TDRE   0x0100        /*    Transmit Data Register Empty */

#define    TC     0x0080        /*    Transmit Complete */

#define    RDRF   0x0040        /*    Receive Data Register Full */

#define    RAF    0x0020        /*    Receiver Active */

#define    IDLE   0x0010        /*    Idle-Line Detected */

#define    OR     0x0008        /*    Overrun Error */

#define    NF     0x0004        /*    Noise Error Flag */

#define    FE     0x0002        /*    Framing Error */

#define    PF     0x0001        /*    Parity Error */

#define SCDR (volatile unsigned short int * const)(0x0e + QSM_CRB)

                                /* SCI Data Register */

#define PORTQS (volatile unsigned char * const)(0x15 + QSM_CRB)

                                /* Port QS Data Register */

#define PQSPAR (volatile unsigned char * const)(0x16 + QSM_CRB)

                                /* PORT QS Pin Assignment Rgister */

/* Any bit cleared (zero) defines the corresponding pin to be an I/O

   pin. Any bit set defines the corresponding pin to be a QSPI

   signal. */

/* note: PQS2 is a digital I/O pin unless the SPI is enabled in which

   case it becomes the SPI serial clock SCK. */

/* note: PQS7 is a digital I/O pin unless the SCI transmitter is

   enabled in which case it becomes the SCI serial output TxD. */

#define QSMFun 0x0

#define QSMDis 0x1

/*

 * PQSPAR Field     | QSM Function | Discrete I/O pin

 *------------------+--------------+------------------   */

#define PQSPA0   0  /*   MISO      |      PQS0           */

#define PQSPA1   1  /*   MOSI      |      PQS1           */

#define PQSPA2   2  /*   SCK       |      PQS2 (see note)*/

#define PQSPA3   3  /*   PCSO/!SS  |      PQS3           */

#define PQSPA4   4  /*   PCS1      |      PQS4           */

#define PQSPA5   5  /*   PCS2      |      PQS5           */

#define PQSPA6   6  /*   PCS3      |      PQS6           */

#define PQSPA7   7  /*   TxD       |      PQS7 (see note)*/

#define DDRQS  (volatile unsigned char * const)(0x17 + QSM_CRB)

                                /* PORT QS Data Direction Register */

/* Clearing a bit makes the corresponding pin an input; setting a bit

   makes the pin an output. */

#define SPCR0 (volatile unsigned short int * const)(0x18 + QSM_CRB)

                                /* QSPI Control Register 0 */

#define    MSTR   0x8000        /*    Master/Slave Mode Select */

#define    WOMQ   0x4000        /*    Wired-OR Mode for QSPI Pins */

#define    BITS   0x3c00        /*    Bits Per Transfer */

#define    CPOL   0x0200        /*    Clock Polarity */

#define    CPHA   0x0100        /*    Clock Phase */

#define    SPBR   0x00ff        /*    Serial Clock Baud Rate */

#define SPCR1 (volatile unsigned short int * const)(0x1a + QSM_CRB)

                                /* QSPI Control Register 1 */

#define    SPE    0x8000        /*    QSPI Enable */

#define    DSCKL  0x7f00        /*    Delay before SCK */

#define    DTL    0x00ff        /*    Length of Delay after Transfer */

#define SPCR2 (volatile unsigned short int * const)(0x1c + QSM_CRB)

                                /* QSPI Control Register 2 */

#define    SPIFIE 0x8000        /*    SPI Finished Interrupt Enable */

#define    WREN   0x4000        /*    Wrap Enable */

#define    WRTO   0x2000        /*    Wrap To */

#define    ENDQP  0x0f00        /*    Ending Queue Pointer */

#define    NEWQP  0x000f        /*    New Queue Pointer Value */

#define SPCR3 (volatile unsigned char * const)(0x1e + QSM_CRB)

                                /* QSPI Control Register 3 */

#define    LOOPQ  0x0400        /*    QSPI Loop Mode */

#define    HMIE   0x0200        /*    HALTA and MODF Interrupt Enable */

#define    HALT   0x0100        /*    Halt */

#define SPSR (volatile unsigned char * const)(0x1f + QSM_CRB)

                                /* QSPI Status Register */

#define    SPIF   0x0080        /*    QSPI Finished Flag */

#define    MODF   0x0040        /*    Mode Fault Flag */

#define    HALTA  0x0020        /*    Halt Acknowlwdge Flag */

#define    CPTQP  x0000f        /*    Completed Queue Pointer */

#define QSPIRR (volatile unsigned char * const)(0x100 + QSM_CRB)

                                /* QSPI Receive Data RAM */

#define QSPITR (volatile unsigned char * const)(0x120 + QSM_CRB)

                                /* QSPI Transmit Data RAM */

#define QSPIcR (volatile unsigned char * const)(0x140 + QSM_CRB)

                                /* QSPI Command RAM */

#endif /* _QSM_H_ */