Subversion Repositories or1k

@c

@c  COPYRIGHT (c) 1988-2002.

@c  On-Line Applications Research Corporation (OAR).

@c  All rights reserved.

@c

@c  timing.texi,v 1.1 2002/07/30 21:43:53 joel Exp

@c

@node Timing Specification, Timing Specification Introduction, Memory Requirements RTEMS RAM Workspace Worksheet, Top

@chapter Timing Specification

@ifinfo

@menu

* Timing Specification Introduction::

* Timing Specification Philosophy::

* Timing Specification Methodology::

@end menu

@end ifinfo

@node Timing Specification Introduction, Timing Specification Philosophy, Timing Specification, Timing Specification

@section Introduction

This chapter provides information pertaining to the

measurement of the performance of RTEMS, the methods of

gathering the timing data, and the usefulness of the data.  Also

discussed are other time critical aspects of RTEMS that affect

an applications design and ultimate throughput.  These aspects

include determinancy, interrupt latency and context switch times.

@node Timing Specification Philosophy, Timing Specification Determinancy, Timing Specification Introduction, Timing Specification

@section Philosophy

@ifinfo

@menu

* Timing Specification Determinancy::

* Timing Specification Interrupt Latency::

* Timing Specification Context Switch Time::

* Timing Specification Directive Times::

@end menu

@end ifinfo

Benchmarks are commonly used to evaluate the

performance of software and hardware.  Benchmarks can be an

effective tool when comparing systems.  Unfortunately,

benchmarks can also be manipulated to justify virtually any

claim.  Benchmarks of real-time executives are difficult to

evaluate for a variety of reasons.  Executives vary in the

robustness of features and options provided.  Even when

executives compare favorably in functionality, it is quite

likely that different methodologies were used to obtain the

timing data.  Another problem is that some executives provide

times for only a small subset of directives,  This is typically

justified by claiming that these are the only time-critical

directives.  The performance of some executives is also very

sensitive to the number of objects in the system.  To obtain any

measure of usefulness, the performance information provided for

an executive should address each of these issues.

When evaluating the performance of a real-time

executive, one typically considers the following areas:

determinancy, directive times, worst case interrupt latency, and

context switch time.  Unfortunately, these areas do not have

standard measurement methodologies.  This allows vendors to

manipulate the results such that their product is favorably

represented.  We have attempted to provide useful and meaningful

timing information for RTEMS.  To insure the usefulness of our

data, the methodology and definitions used to obtain and

describe the data are also documented.

@node Timing Specification Determinancy, Timing Specification Interrupt Latency, Timing Specification Philosophy, Timing Specification Philosophy

@subsection Determinancy

The correctness of data in a real-time system must

always be judged by its timeliness.  In many real-time systems,

obtaining the correct answer does not necessarily solve the

problem.  For example, in a nuclear reactor it is not enough to

determine that the core is overheating.  This situation must be

detected and acknowledged early enough that corrective action

can be taken and a meltdown avoided.

Consequently, a system designer must be able to

predict the worst-case behavior of the application running under

the selected executive.  In this light, it is important that a

real-time system perform consistently regardless of the number

of tasks, semaphores, or other resources allocated.  An

important design goal of a real-time executive is that all

internal algorithms be fixed-cost.  Unfortunately, this goal is

difficult to completely meet without sacrificing the robustness

of the executive's feature set.

Many executives use the term deterministic to mean

that the execution times of their services can be predicted.

However, they often provide formulas to modify execution times

based upon the number of objects in the system.  This usage is

in sharp contrast to the notion of deterministic meaning fixed

cost.

Almost all RTEMS directives execute in a fixed amount

of time regardless of the number of objects present in the

system.  The primary exception occurs when a task blocks while

acquiring a resource and specifies a non-zero timeout interval.

Other exceptions are message queue broadcast,

obtaining a variable length memory block, object name to ID

translation, and deleting a resource upon which tasks are

waiting.  In addition, the time required to service a clock tick

interrupt is based upon the number of timeouts and other

"events" which must be processed at that tick.  This second

group is composed primarily of capabilities which are inherently

non-deterministic but are infrequently used in time critical

situations.  The major exception is that of servicing a clock

tick.  However, most applications have a very small number of

timeouts which expire at exactly the same millisecond (usually

none, but occasionally two or three).

@node Timing Specification Interrupt Latency, Timing Specification Context Switch Time, Timing Specification Determinancy, Timing Specification Philosophy

@subsection Interrupt Latency

Interrupt latency is the delay between the CPU's

receipt of an interrupt request and the execution of the first

application-specific instruction in an interrupt service

routine.  Interrupts are a critical component of most real-time

applications and it is critical that they be acted upon as

quickly as possible.

Knowledge of the worst case interrupt latency of an

executive aids the application designer in determining the

maximum period of time between the generation of an interrupt

and an interrupt handler responding to that interrupt.  The

interrupt latency of an system is the greater of the executive's

and the applications's interrupt latency.  If the application

disables interrupts longer than the executive, then the

application's interrupt latency is the system's worst case

interrupt disable period.

The worst case interrupt latency for a real-time

executive is based upon the following components:

@itemize @bullet

@item the longest period of time interrupts are disabled

by the executive,

@item the overhead required by the executive at the

beginning of each ISR,

@item the time required for the CPU to vector the

interrupt, and

@item for some microprocessors, the length of the longest

instruction.

@end itemize

The first component is irrelevant if an interrupt

occurs when interrupts are enabled, although it must be included

in a worst case analysis.  The third and fourth components are

particular to a CPU implementation and are not dependent on the

executive.  The fourth component is ignored by this document

because most applications use only a subset of a

microprocessor's instruction set.  Because of this the longest

instruction actually executed is application dependent.  The

worst case interrupt latency of an executive is typically

defined as the sum of components (1) and (2).  The second

component includes the time necessry for RTEMS to save registers

and vector to the user-defined handler.  RTEMS includes the

third component, the time required for the CPU to vector the

interrupt, because it is a required part of any interrupt.

Many executives report the maximum interrupt disable

period as their interrupt latency and ignore the other

components.  This results in very low worst-case interrupt

latency times which are not indicative of actual application

performance.  The definition used by RTEMS results in a higher

interrupt latency being reported, but accurately reflects the

longest delay between the CPU's receipt of an interrupt request

and the execution of the first application-specific instruction

in an interrupt service routine.

The actual interrupt latency times are reported in

the Timing Data chapter of this supplement.

@node Timing Specification Context Switch Time, Timing Specification Directive Times, Timing Specification Interrupt Latency, Timing Specification Philosophy

@subsection Context Switch Time

An RTEMS context switch is defined as the act of

taking the CPU from the currently executing task and giving it

to another task.  This process involves the following components:

@itemize @bullet

@item Saving the hardware state of the current task.

@item Optionally, invoking the TASK_SWITCH user extension.

@item Restoring the hardware state of the new task.

@end itemize

RTEMS defines the hardware state of a task to include

the CPU's data registers, address registers, and, optionally,

floating point registers.

Context switch time is often touted as a performance

measure of real-time executives.  However, a context switch is

performed as part of a directive's actions and should be viewed

as such when designing an application.  For example, if a task

is unable to acquire a semaphore and blocks, a context switch is

required to transfer control from the blocking task to a new

task.  From the application's perspective, the context switch is

a direct result of not acquiring the semaphore.  In this light,

the context switch time is no more relevant than the performance

of any other of the executive's subroutines which are not

directly accessible by the application.

In spite of the inappropriateness of using the

context switch time as a performance metric, RTEMS context

switch times for floating point and non-floating points tasks

are provided for comparison purposes.  Of the executives which

actually support floating point operations, many do not report

context switch times for floating point context switch time.

This results in a reported context switch time which is

meaningless for an application with floating point tasks.

The actual context switch times are reported in the

Timing Data chapter of this supplement.

@node Timing Specification Directive Times, Timing Specification Methodology, Timing Specification Context Switch Time, Timing Specification Philosophy

@subsection Directive Times

Directives are the application's interface to the

executive, and as such their execution times are critical in

determining the performance of the application.  For example, an

application using a semaphore to protect a critical data

structure should be aware of the time required to acquire and

release a semaphore.  In addition, the application designer can

utilize the directive execution times to evaluate the

performance of different synchronization and communication

mechanisms.

The actual directive execution times are reported in

the Timing Data chapter of this supplement.

@node Timing Specification Methodology, Timing Specification Software Platform, Timing Specification Directive Times, Timing Specification

@section Methodology

@ifinfo

@menu

* Timing Specification Software Platform::

* Timing Specification Hardware Platform::

* Timing Specification What is measured?::

* Timing Specification What is not measured?::

* Timing Specification Terminology::

@end menu

@end ifinfo

@node Timing Specification Software Platform, Timing Specification Hardware Platform, Timing Specification Methodology, Timing Specification Methodology

@subsection Software Platform

The RTEMS timing suite is written in C.  The overhead

of passing arguments to RTEMS by C is not timed.  The times

reported represent the amount of time from entering to exiting

RTEMS.

The tests are based upon one of two execution models:

(1) single invocation times, and (2) average times of repeated

invocations.  Single invocation times are provided for

directives which cannot easily be invoked multiple times in the

same scenario.  For example, the times reported for entering and

exiting an interrupt service routine are single invocation

times.  The second model is used for directives which can easily

be invoked multiple times in the same scenario.  For example,

the times reported for semaphore obtain and semaphore release

are averages of multiple invocations.  At least 100 invocations

are used to obtain the average.

@node Timing Specification Hardware Platform, Timing Specification What is measured?, Timing Specification Software Platform, Timing Specification Methodology

@subsection Hardware Platform

Since RTEMS supports a variety of processors, the

hardware platform used to gather the benchmark times must also

vary.  Therefore, for each processor supported the hardware

platform must be defined.  Each definition will include a brief

description of the target hardware platform including the clock

speed, memory wait states encountered, and any other pertinent

information.  This definition may be found in the processor

dependent timing data chapter within this supplement.

@node Timing Specification What is measured?, Timing Specification What is not measured?, Timing Specification Hardware Platform, Timing Specification Methodology

@subsection What is measured?

An effort was made to provide execution times for a

large portion of RTEMS.  Times were provided for most directives

regardless of whether or not they are typically used in time

critical code.  For example, execution times are provided for

all object create and delete directives, even though these are

typically part of application initialization.

The times include all RTEMS actions necessary in a

particular scenario.  For example, all times for blocking

directives include the context switch necessary to transfer

control to a new task.  Under no circumstances is it necessary

to add context switch time to the reported times.

The following list describes the objects created by

the timing suite:

@itemize @bullet

@item All tasks are non-floating point.

@item All tasks are created as local objects.

@item No timeouts are used on blocking directives.

@item All tasks wait for objects in FIFO order.

@end itemize

In addition, no user extensions are configured.

@node Timing Specification What is not measured?, Timing Specification Terminology, Timing Specification What is measured?, Timing Specification Methodology

@subsection What is not measured?

The times presented in this document are not intended

to represent best or worst case times, nor are all directives

included.  For example, no times are provided for the initialize

executive and fatal_error_occurred directives.  Other than the

exceptions detailed in the Determinancy section, all directives

will execute in the fixed length of time given.

Other than entering and exiting an interrupt service

routine, all directives were executed from tasks and not from

interrupt service routines.  Directives invoked from ISRs, when

allowable, will execute in slightly less time than when invoked

from a task because rescheduling is delayed until the interrupt

exits.

@node Timing Specification Terminology, MYBSP Timing Data, Timing Specification What is not measured?, Timing Specification Methodology

@subsection Terminology

The following is a list of phrases which are used to

distinguish individual execution paths of the directives taken

during the RTEMS performance analysis:

@table @b

@item another task

The directive was performed

on a task other than the calling task.

@item available

A task attempted to obtain a resource and

immediately acquired it.

@item blocked task

The task operated upon by the

directive was blocked waiting for a resource.

@item caller blocks

The requested resoure was not

immediately available and the calling task chose to wait.

@item calling task

The task invoking the directive.

@item messages flushed

One or more messages was flushed

from the message queue.

@item no messages flushed

No messages were flushed from

the message queue.

@item not available

A task attempted to obtain a resource

and could not immediately acquire it.

@item no reschedule

The directive did not require a

rescheduling operation.

@item NO_WAIT

A resource was not available and the

calling task chose to return immediately via the NO_WAIT option

with an error.

@item obtain current

The current value of something was

requested by the calling task.

@item preempts caller

The release of a resource caused a

task of higher priority than the calling to be readied and it

became the executing task.

@item ready task

The task operated upon by the directive

was in the ready state.

@item reschedule

The actions of the directive

necessitated a rescheduling operation.

@item returns to caller

The directive succeeded and

immediately returned to the calling task.

@item returns to interrupted task

The instructions

executed immediately following this interrupt will be in the

interrupted task.

@item returns to nested interrupt

The instructions

executed immediately following this interrupt will be in a

previously interrupted ISR.

@item returns to preempting task

The instructions

executed immediately following this interrupt or signal handler

will be in a task other than the interrupted task.

@item signal to self

The signal set was sent to the

calling task and signal processing was enabled.

@item suspended task

The task operated upon by the

directive was in the suspended state.

@item task readied

The release of a resource caused a

task of lower or equal priority to be readied and the calling

task remained the executing task.

@item yield

The act of attempting to voluntarily release

the CPU.

@end table