| 1 |
199 |
simons |
/* $Id: dma.h,v 1.1.1.1 2001-09-10 07:44:42 simons Exp $
|
| 2 |
|
|
* linux/include/asm/dma.h: Defines for using and allocating dma channels.
|
| 3 |
|
|
* Written by Hennus Bergman, 1992.
|
| 4 |
|
|
* High DMA channel support & info by Hannu Savolainen
|
| 5 |
|
|
* and John Boyd, Nov. 1992.
|
| 6 |
|
|
*
|
| 7 |
|
|
* NOTE: all this is true *only* for ISA/EISA expansions on Mips boards
|
| 8 |
|
|
* and can only be used for expansion cards. Onboard DMA controller, such
|
| 9 |
|
|
* as the R4030 on Jazz boards behave totally different!
|
| 10 |
|
|
*/
|
| 11 |
|
|
|
| 12 |
|
|
#ifndef __ASM_MIPS_DMA_H
|
| 13 |
|
|
#define __ASM_MIPS_DMA_H
|
| 14 |
|
|
|
| 15 |
|
|
#include <asm/io.h> /* need byte IO */
|
| 16 |
|
|
|
| 17 |
|
|
|
| 18 |
|
|
#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
|
| 19 |
|
|
#define dma_outb outb_p
|
| 20 |
|
|
#else
|
| 21 |
|
|
#define dma_outb outb
|
| 22 |
|
|
#endif
|
| 23 |
|
|
|
| 24 |
|
|
#define dma_inb inb
|
| 25 |
|
|
|
| 26 |
|
|
/*
|
| 27 |
|
|
* NOTES about DMA transfers:
|
| 28 |
|
|
*
|
| 29 |
|
|
* controller 1: channels 0-3, byte operations, ports 00-1F
|
| 30 |
|
|
* controller 2: channels 4-7, word operations, ports C0-DF
|
| 31 |
|
|
*
|
| 32 |
|
|
* - ALL registers are 8 bits only, regardless of transfer size
|
| 33 |
|
|
* - channel 4 is not used - cascades 1 into 2.
|
| 34 |
|
|
* - channels 0-3 are byte - addresses/counts are for physical bytes
|
| 35 |
|
|
* - channels 5-7 are word - addresses/counts are for physical words
|
| 36 |
|
|
* - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
|
| 37 |
|
|
* - transfer count loaded to registers is 1 less than actual count
|
| 38 |
|
|
* - controller 2 offsets are all even (2x offsets for controller 1)
|
| 39 |
|
|
* - page registers for 5-7 don't use data bit 0, represent 128K pages
|
| 40 |
|
|
* - page registers for 0-3 use bit 0, represent 64K pages
|
| 41 |
|
|
*
|
| 42 |
|
|
* DMA transfers are limited to the lower 16MB of _physical_ memory.
|
| 43 |
|
|
* Note that addresses loaded into registers must be _physical_ addresses,
|
| 44 |
|
|
* not logical addresses (which may differ if paging is active).
|
| 45 |
|
|
*
|
| 46 |
|
|
* Address mapping for channels 0-3:
|
| 47 |
|
|
*
|
| 48 |
|
|
* A23 ... A16 A15 ... A8 A7 ... A0 (Physical addresses)
|
| 49 |
|
|
* | ... | | ... | | ... |
|
| 50 |
|
|
* | ... | | ... | | ... |
|
| 51 |
|
|
* | ... | | ... | | ... |
|
| 52 |
|
|
* P7 ... P0 A7 ... A0 A7 ... A0
|
| 53 |
|
|
* | Page | Addr MSB | Addr LSB | (DMA registers)
|
| 54 |
|
|
*
|
| 55 |
|
|
* Address mapping for channels 5-7:
|
| 56 |
|
|
*
|
| 57 |
|
|
* A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0 (Physical addresses)
|
| 58 |
|
|
* | ... | \ \ ... \ \ \ ... \ \
|
| 59 |
|
|
* | ... | \ \ ... \ \ \ ... \ (not used)
|
| 60 |
|
|
* | ... | \ \ ... \ \ \ ... \
|
| 61 |
|
|
* P7 ... P1 (0) A7 A6 ... A0 A7 A6 ... A0
|
| 62 |
|
|
* | Page | Addr MSB | Addr LSB | (DMA registers)
|
| 63 |
|
|
*
|
| 64 |
|
|
* Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
|
| 65 |
|
|
* and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
|
| 66 |
|
|
* the hardware level, so odd-byte transfers aren't possible).
|
| 67 |
|
|
*
|
| 68 |
|
|
* Transfer count (_not # bytes_) is limited to 64K, represented as actual
|
| 69 |
|
|
* count - 1 : 64K => 0xFFFF, 1 => 0x0000. Thus, count is always 1 or more,
|
| 70 |
|
|
* and up to 128K bytes may be transferred on channels 5-7 in one operation.
|
| 71 |
|
|
*
|
| 72 |
|
|
*/
|
| 73 |
|
|
|
| 74 |
|
|
#define MAX_DMA_CHANNELS 8
|
| 75 |
|
|
|
| 76 |
|
|
/*
|
| 77 |
|
|
* The maximum address that we can perform a DMA transfer to on this platform
|
| 78 |
|
|
* This describes only the PC style part of the DMA logic like on Deskstations
|
| 79 |
|
|
* or Acer PICA but not the much more versatile DMA logic used for the
|
| 80 |
|
|
* local devices on Acer PICA or Magnums.
|
| 81 |
|
|
*/
|
| 82 |
|
|
#define MAX_DMA_ADDRESS 0x1000000
|
| 83 |
|
|
|
| 84 |
|
|
/* 8237 DMA controllers */
|
| 85 |
|
|
#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */
|
| 86 |
|
|
#define IO_DMA2_BASE 0xC0 /* 16 bit master DMA, ch 4(=slave input)..7 */
|
| 87 |
|
|
|
| 88 |
|
|
/* DMA controller registers */
|
| 89 |
|
|
#define DMA1_CMD_REG 0x08 /* command register (w) */
|
| 90 |
|
|
#define DMA1_STAT_REG 0x08 /* status register (r) */
|
| 91 |
|
|
#define DMA1_REQ_REG 0x09 /* request register (w) */
|
| 92 |
|
|
#define DMA1_MASK_REG 0x0A /* single-channel mask (w) */
|
| 93 |
|
|
#define DMA1_MODE_REG 0x0B /* mode register (w) */
|
| 94 |
|
|
#define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */
|
| 95 |
|
|
#define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */
|
| 96 |
|
|
#define DMA1_RESET_REG 0x0D /* Master Clear (w) */
|
| 97 |
|
|
#define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */
|
| 98 |
|
|
#define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */
|
| 99 |
|
|
|
| 100 |
|
|
#define DMA2_CMD_REG 0xD0 /* command register (w) */
|
| 101 |
|
|
#define DMA2_STAT_REG 0xD0 /* status register (r) */
|
| 102 |
|
|
#define DMA2_REQ_REG 0xD2 /* request register (w) */
|
| 103 |
|
|
#define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */
|
| 104 |
|
|
#define DMA2_MODE_REG 0xD6 /* mode register (w) */
|
| 105 |
|
|
#define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */
|
| 106 |
|
|
#define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */
|
| 107 |
|
|
#define DMA2_RESET_REG 0xDA /* Master Clear (w) */
|
| 108 |
|
|
#define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */
|
| 109 |
|
|
#define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */
|
| 110 |
|
|
|
| 111 |
|
|
#define DMA_ADDR_0 0x00 /* DMA address registers */
|
| 112 |
|
|
#define DMA_ADDR_1 0x02
|
| 113 |
|
|
#define DMA_ADDR_2 0x04
|
| 114 |
|
|
#define DMA_ADDR_3 0x06
|
| 115 |
|
|
#define DMA_ADDR_4 0xC0
|
| 116 |
|
|
#define DMA_ADDR_5 0xC4
|
| 117 |
|
|
#define DMA_ADDR_6 0xC8
|
| 118 |
|
|
#define DMA_ADDR_7 0xCC
|
| 119 |
|
|
|
| 120 |
|
|
#define DMA_CNT_0 0x01 /* DMA count registers */
|
| 121 |
|
|
#define DMA_CNT_1 0x03
|
| 122 |
|
|
#define DMA_CNT_2 0x05
|
| 123 |
|
|
#define DMA_CNT_3 0x07
|
| 124 |
|
|
#define DMA_CNT_4 0xC2
|
| 125 |
|
|
#define DMA_CNT_5 0xC6
|
| 126 |
|
|
#define DMA_CNT_6 0xCA
|
| 127 |
|
|
#define DMA_CNT_7 0xCE
|
| 128 |
|
|
|
| 129 |
|
|
#define DMA_PAGE_0 0x87 /* DMA page registers */
|
| 130 |
|
|
#define DMA_PAGE_1 0x83
|
| 131 |
|
|
#define DMA_PAGE_2 0x81
|
| 132 |
|
|
#define DMA_PAGE_3 0x82
|
| 133 |
|
|
#define DMA_PAGE_5 0x8B
|
| 134 |
|
|
#define DMA_PAGE_6 0x89
|
| 135 |
|
|
#define DMA_PAGE_7 0x8A
|
| 136 |
|
|
|
| 137 |
|
|
#define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */
|
| 138 |
|
|
#define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */
|
| 139 |
|
|
#define DMA_MODE_CASCADE 0xC0 /* pass thru DREQ->HRQ, DACK<-HLDA only */
|
| 140 |
|
|
|
| 141 |
|
|
/* enable/disable a specific DMA channel */
|
| 142 |
|
|
static __inline__ void enable_dma(unsigned int dmanr)
|
| 143 |
|
|
{
|
| 144 |
|
|
if (dmanr<=3)
|
| 145 |
|
|
dma_outb(dmanr, DMA1_MASK_REG);
|
| 146 |
|
|
else
|
| 147 |
|
|
dma_outb(dmanr & 3, DMA2_MASK_REG);
|
| 148 |
|
|
}
|
| 149 |
|
|
|
| 150 |
|
|
static __inline__ void disable_dma(unsigned int dmanr)
|
| 151 |
|
|
{
|
| 152 |
|
|
if (dmanr<=3)
|
| 153 |
|
|
dma_outb(dmanr | 4, DMA1_MASK_REG);
|
| 154 |
|
|
else
|
| 155 |
|
|
dma_outb((dmanr & 3) | 4, DMA2_MASK_REG);
|
| 156 |
|
|
}
|
| 157 |
|
|
|
| 158 |
|
|
/* Clear the 'DMA Pointer Flip Flop'.
|
| 159 |
|
|
* Write 0 for LSB/MSB, 1 for MSB/LSB access.
|
| 160 |
|
|
* Use this once to initialize the FF to a known state.
|
| 161 |
|
|
* After that, keep track of it. :-)
|
| 162 |
|
|
* --- In order to do that, the DMA routines below should ---
|
| 163 |
|
|
* --- only be used while interrupts are disabled! ---
|
| 164 |
|
|
*/
|
| 165 |
|
|
static __inline__ void clear_dma_ff(unsigned int dmanr)
|
| 166 |
|
|
{
|
| 167 |
|
|
if (dmanr<=3)
|
| 168 |
|
|
dma_outb(0, DMA1_CLEAR_FF_REG);
|
| 169 |
|
|
else
|
| 170 |
|
|
dma_outb(0, DMA2_CLEAR_FF_REG);
|
| 171 |
|
|
}
|
| 172 |
|
|
|
| 173 |
|
|
/* set mode (above) for a specific DMA channel */
|
| 174 |
|
|
static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
|
| 175 |
|
|
{
|
| 176 |
|
|
if (dmanr<=3)
|
| 177 |
|
|
dma_outb(mode | dmanr, DMA1_MODE_REG);
|
| 178 |
|
|
else
|
| 179 |
|
|
dma_outb(mode | (dmanr&3), DMA2_MODE_REG);
|
| 180 |
|
|
}
|
| 181 |
|
|
|
| 182 |
|
|
/* Set only the page register bits of the transfer address.
|
| 183 |
|
|
* This is used for successive transfers when we know the contents of
|
| 184 |
|
|
* the lower 16 bits of the DMA current address register, but a 64k boundary
|
| 185 |
|
|
* may have been crossed.
|
| 186 |
|
|
*/
|
| 187 |
|
|
static __inline__ void set_dma_page(unsigned int dmanr, char pagenr)
|
| 188 |
|
|
{
|
| 189 |
|
|
switch(dmanr) {
|
| 190 |
|
|
case 0:
|
| 191 |
|
|
dma_outb(pagenr, DMA_PAGE_0);
|
| 192 |
|
|
break;
|
| 193 |
|
|
case 1:
|
| 194 |
|
|
dma_outb(pagenr, DMA_PAGE_1);
|
| 195 |
|
|
break;
|
| 196 |
|
|
case 2:
|
| 197 |
|
|
dma_outb(pagenr, DMA_PAGE_2);
|
| 198 |
|
|
break;
|
| 199 |
|
|
case 3:
|
| 200 |
|
|
dma_outb(pagenr, DMA_PAGE_3);
|
| 201 |
|
|
break;
|
| 202 |
|
|
case 5:
|
| 203 |
|
|
dma_outb(pagenr & 0xfe, DMA_PAGE_5);
|
| 204 |
|
|
break;
|
| 205 |
|
|
case 6:
|
| 206 |
|
|
dma_outb(pagenr & 0xfe, DMA_PAGE_6);
|
| 207 |
|
|
break;
|
| 208 |
|
|
case 7:
|
| 209 |
|
|
dma_outb(pagenr & 0xfe, DMA_PAGE_7);
|
| 210 |
|
|
break;
|
| 211 |
|
|
}
|
| 212 |
|
|
}
|
| 213 |
|
|
|
| 214 |
|
|
|
| 215 |
|
|
/* Set transfer address & page bits for specific DMA channel.
|
| 216 |
|
|
* Assumes dma flipflop is clear.
|
| 217 |
|
|
*/
|
| 218 |
|
|
static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
|
| 219 |
|
|
{
|
| 220 |
|
|
set_dma_page(dmanr, a>>16);
|
| 221 |
|
|
if (dmanr <= 3) {
|
| 222 |
|
|
dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
|
| 223 |
|
|
dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
|
| 224 |
|
|
} else {
|
| 225 |
|
|
dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
|
| 226 |
|
|
dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
|
| 227 |
|
|
}
|
| 228 |
|
|
}
|
| 229 |
|
|
|
| 230 |
|
|
|
| 231 |
|
|
/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
|
| 232 |
|
|
* a specific DMA channel.
|
| 233 |
|
|
* You must ensure the parameters are valid.
|
| 234 |
|
|
* NOTE: from a manual: "the number of transfers is one more
|
| 235 |
|
|
* than the initial word count"! This is taken into account.
|
| 236 |
|
|
* Assumes dma flip-flop is clear.
|
| 237 |
|
|
* NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
|
| 238 |
|
|
*/
|
| 239 |
|
|
static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
|
| 240 |
|
|
{
|
| 241 |
|
|
count--;
|
| 242 |
|
|
if (dmanr <= 3) {
|
| 243 |
|
|
dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
|
| 244 |
|
|
dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
|
| 245 |
|
|
} else {
|
| 246 |
|
|
dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
|
| 247 |
|
|
dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
|
| 248 |
|
|
}
|
| 249 |
|
|
}
|
| 250 |
|
|
|
| 251 |
|
|
|
| 252 |
|
|
/* Get DMA residue count. After a DMA transfer, this
|
| 253 |
|
|
* should return zero. Reading this while a DMA transfer is
|
| 254 |
|
|
* still in progress will return unpredictable results.
|
| 255 |
|
|
* If called before the channel has been used, it may return 1.
|
| 256 |
|
|
* Otherwise, it returns the number of _bytes_ left to transfer.
|
| 257 |
|
|
*
|
| 258 |
|
|
* Assumes DMA flip-flop is clear.
|
| 259 |
|
|
*/
|
| 260 |
|
|
static __inline__ int get_dma_residue(unsigned int dmanr)
|
| 261 |
|
|
{
|
| 262 |
|
|
unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
|
| 263 |
|
|
: ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
|
| 264 |
|
|
|
| 265 |
|
|
/* using short to get 16-bit wrap around */
|
| 266 |
|
|
unsigned short count;
|
| 267 |
|
|
|
| 268 |
|
|
count = 1 + dma_inb(io_port);
|
| 269 |
|
|
count += dma_inb(io_port) << 8;
|
| 270 |
|
|
|
| 271 |
|
|
return (dmanr<=3)? count : (count<<1);
|
| 272 |
|
|
}
|
| 273 |
|
|
|
| 274 |
|
|
|
| 275 |
|
|
/* These are in kernel/dma.c: */
|
| 276 |
|
|
extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
|
| 277 |
|
|
extern void free_dma(unsigned int dmanr); /* release it again */
|
| 278 |
|
|
|
| 279 |
|
|
/*
|
| 280 |
|
|
* DMA memory allocation - formerly in include/linux/mm.h
|
| 281 |
|
|
*/
|
| 282 |
|
|
#define __get_dma_pages(priority, order) __get_free_pages((priority),(order), 1)
|
| 283 |
|
|
|
| 284 |
|
|
#endif /* __ASM_MIPS_DMA_H */
|
