Subversion Repositories or1k_old

/* $Id: tpqic02.h,v 1.1 2005-12-20 11:32:27 jcastillo Exp $

 *

 * Include file for QIC-02 driver for Linux.

 *

 * Copyright (c) 1992--1995 by H. H. Bergman. All rights reserved.

 *

 * ******* USER CONFIG SECTION BELOW (Near line 70) *******

 */

#ifndef _LINUX_TPQIC02_H

#define _LINUX_TPQIC02_H

#include <linux/config.h>

#if CONFIG_QIC02_TAPE

/* need to have QIC02_TAPE_DRIVE and QIC02_TAPE_IFC expand to something */

#include <linux/mtio.h>

/* Make QIC02_TAPE_IFC expand to something.

 *

 * The only difference between WANGTEK and EVEREX is in the

 * handling of the DMA channel 3.

 * Note that the driver maps EVEREX to WANGTEK internally for speed

 * reasons. Externally WANGTEK==1, EVEREX==2, ARCHIVE==3.

 * These must correspond to the values used in qic02config(1).

 *

 * Support for Mountain controllers was added by Erik Jacobson

 * and severely hacked by me.   -- hhb

 */

#define WANGTEK         1                  /* don't know about Wangtek QIC-36 */

#define EVEREX          (WANGTEK+1)  /* I heard *some* of these are identical */

#define EVEREX_811V     EVEREX                        /* With TEAC MT 2ST 45D */

#define EVEREX_831V     EVEREX

#define ARCHIVE         3

#define ARCHIVE_SC400   ARCHIVE        /* rumoured to be from the pre-SMD-age */

#define ARCHIVE_SC402   ARCHIVE                /* don't know much about SC400 */

#define ARCHIVE_SC499   ARCHIVE       /* SC402 and SC499R should be identical */

#define MOUNTAIN        5                      /* Mountain Computer Interface */

/*********** START OF USER CONFIGURABLE SECTION ************/

/* Tape configuration: Select DRIVE, IFC, PORT, IRQ and DMA below.

 * Runtime (re)configuration is not supported yet.

 *

 * Tape drive configuration:    (MT_IS* constants are defined in mtio.h)

 *

 * QIC02_TAPE_DRIVE = MT_ISWT5150

 *      - Wangtek 5150, format: up to QIC-150.

 * QIC02_TAPE_DRIVE = MT_ISQIC02_ALL_FEATURES

 *      - Enables some optional QIC02 commands that some drives may lack.

 *        It is provided so you can check which are supported by your drive.

 *        Refer to tpqic02.h for others.

 *

 * Supported interface cards: QIC02_TAPE_IFC =

 *      WANGTEK,

 *      ARCHIVE_SC402, ARCHIVE_SC499.   (both same programming interface)

 *

 * Make sure you have the I/O ports/DMA channels

 * and IRQ stuff configured properly!

 * NOTE: There may be other device drivers using the same major

 *       number. This must be avoided. Check for timer.h conflicts too.

 *

 * If you have an EVEREX EV-831 card and you are using DMA channel 3,

 * you will probably have to ``#define QIC02_TAPE_DMA3_FIX'' below.

 */

/* CONFIG_QIC02_DYNCONF can be defined in autoconf.h, by `make config' */

/*** #undef CONFIG_QIC02_DYNCONF ***/

#ifndef CONFIG_QIC02_DYNCONF

#define QIC02_TAPE_DRIVE        MT_ISQIC02_ALL_FEATURES  /* drive type */

/* #define QIC02_TAPE_DRIVE     MT_ISWT5150 */

/* #define QIC02_TAPE_DRIVE     MT_ISARCHIVE_5945L2 */

/* #define QIC02_TAPE_DRIVE     MT_ISTEAC_MT2ST */

/* #define QIC02_TAPE_DRIVE     MT_ISARCHIVE_2150L */

/* #define QIC02_TAPE_DRIVE     MT_ISARCHIVESC499 */

/* Either WANGTEK, ARCHIVE or MOUNTAIN. Not EVEREX.

 * If you have an EVEREX, use WANGTEK and try the DMA3_FIX below.

 */

#define QIC02_TAPE_IFC          WANGTEK /* interface card type */

/* #define QIC02_TAPE_IFC               ARCHIVE */

/* #define QIC02_TAPE_IFC               MOUNTAIN */

#define QIC02_TAPE_PORT         0x300   /* controller port address */

#define QIC02_TAPE_IRQ          5       /* For IRQ2, use 9 here, others normal. */

#define QIC02_TAPE_DMA          1       /* either 1 or 3, because 2 is used by the floppy */

/* If DMA3 doesn't work, but DMA1 does, and you have a

 * Wangtek/Everex card, you can try #define-ing the flag

 * below. Note that you should also change the DACK jumper

 * for Wangtek/Everex cards when changing the DMA channel.

 */

#undef QIC02_TAPE_DMA3_FIX

/************ END OF USER CONFIGURABLE SECTION *************/

/* I put the stuff above in config.in, but a few recompiles, to

 * verify different configurations, and several days later I decided

 * to change it back again.

 */

/* NOTE: TP_HAVE_DENS should distinguish between available densities (?)

 * NOTE: Drive select is not implemented -- I have only one tape streamer,

 *       so I'm unable and unmotivated to test and implement that. ;-) ;-)

 */

#if QIC02_TAPE_DRIVE == MT_ISWT5150

#define TP_HAVE_DENS    1

#define TP_HAVE_BSF     0        /* nope */

#define TP_HAVE_FSR     0        /* nope */

#define TP_HAVE_BSR     0        /* nope */

#define TP_HAVE_EOD     0        /* most of the time */

#define TP_HAVE_SEEK    0

#define TP_HAVE_TELL    0

#define TP_HAVE_RAS1    1

#define TP_HAVE_RAS2    1

#elif QIC02_TAPE_DRIVE == MT_ISARCHIVESC499     /* Archive SC-499 QIC-36 controller */

#define TP_HAVE_DENS    1       /* can do set density (QIC-11 / QIC-24) */

#define TP_HAVE_BSF     0

#define TP_HAVE_FSR     1       /* can skip one block forwards */

#define TP_HAVE_BSR     1       /* can skip one block backwards */

#define TP_HAVE_EOD     1       /* can seek to end of recorded data */

#define TP_HAVE_SEEK    0

#define TP_HAVE_TELL    0

#define TP_HAVE_RAS1    1       /* can run selftest 1 */

#define TP_HAVE_RAS2    1       /* can run selftest 2 */

/* These last two selftests shouldn't be used yet! */

#elif (QIC02_TAPE_DRIVE == MT_ISARCHIVE_2060L) || (QIC02_TAPE_DRIVE == MT_ISARCHIVE_2150L)

#define TP_HAVE_DENS    1       /* can do set density (QIC-24 / QIC-120 / QIC-150) */

#define TP_HAVE_BSF     0

#define TP_HAVE_FSR     1       /* can skip one block forwards */

#define TP_HAVE_BSR     1       /* can skip one block backwards */

#define TP_HAVE_EOD     1       /* can seek to end of recorded data */

#define TP_HAVE_TELL    1       /* can read current block address */

#define TP_HAVE_SEEK    1       /* can seek to block */

#define TP_HAVE_RAS1    1       /* can run selftest 1 */

#define TP_HAVE_RAS2    1       /* can run selftest 2 */

/* These last two selftests shouldn't be used yet! */

#elif QIC02_TAPE_DRIVE == MT_ISARCHIVE_5945L2

/* can anyone verify this entry?? */

#define TP_HAVE_DENS    1       /* can do set density?? (QIC-24??) */

#define TP_HAVE_BSF     0

#define TP_HAVE_FSR     1       /* can skip one block forwards */

#define TP_HAVE_BSR     1       /* can skip one block backwards */

#define TP_HAVE_EOD     1       /* can seek to end of recorded data */

#define TP_HAVE_TELL    1       /* can read current block address */

#define TP_HAVE_SEEK    1       /* can seek to block */

#define TP_HAVE_RAS1    1       /* can run selftest 1 */

#define TP_HAVE_RAS2    1       /* can run selftest 2 */

/* These last two selftests shouldn't be used yet! */

#elif QIC02_TAPE_DRIVE == MT_ISTEAC_MT2ST

/* can anyone verify this entry?? */

#define TP_HAVE_DENS    0        /* cannot do set density?? (QIC-150?) */

#define TP_HAVE_BSF     0

#define TP_HAVE_FSR     1       /* can skip one block forwards */

#define TP_HAVE_BSR     1       /* can skip one block backwards */

#define TP_HAVE_EOD     1       /* can seek to end of recorded data */

#define TP_HAVE_SEEK    1       /* can seek to block */

#define TP_HAVE_TELL    1       /* can read current block address */

#define TP_HAVE_RAS1    1       /* can run selftest 1 */

#define TP_HAVE_RAS2    1       /* can run selftest 2 */

/* These last two selftests shouldn't be used yet! */

#elif QIC02_TAPE_DRIVE == MT_ISQIC02_ALL_FEATURES

#define TP_HAVE_DENS    1       /* can do set density */

#define TP_HAVE_BSF     1       /* can search filemark backwards */

#define TP_HAVE_FSR     1       /* can skip one block forwards */

#define TP_HAVE_BSR     1       /* can skip one block backwards */

#define TP_HAVE_EOD     1       /* can seek to end of recorded data */

#define TP_HAVE_SEEK    1       /* seek to block address */

#define TP_HAVE_TELL    1       /* tell current block address */

#define TP_HAVE_RAS1    1       /* can run selftest 1 */

#define TP_HAVE_RAS2    1       /* can run selftest 2 */

/* These last two selftests shouldn't be used yet! */

#else

#error No QIC-02 tape drive type defined!

/* If your drive is not listed above, first try the 'ALL_FEATURES',

 * to see what commands are supported, then create your own entry in

 * the list above. You may want to mail it to me, so that I can include

 * it in the next release.

 */

#endif

#endif /* !CONFIG_QIC02_DYNCONF */

/* WANGTEK interface card specifics */

#define WT_QIC02_STAT_PORT      (QIC02_TAPE_PORT)

#define WT_QIC02_CTL_PORT       (QIC02_TAPE_PORT)

#define WT_QIC02_CMD_PORT       (QIC02_TAPE_PORT+1)

#define WT_QIC02_DATA_PORT      (QIC02_TAPE_PORT+1)

/* status register bits (Active LOW!) */

#define WT_QIC02_STAT_READY     0x01

#define WT_QIC02_STAT_EXCEPTION 0x02

#define WT_QIC02_STAT_MASK      (WT_QIC02_STAT_READY|WT_QIC02_STAT_EXCEPTION)

#define WT_QIC02_STAT_RESETMASK 0x07

#define WT_QIC02_STAT_RESETVAL  (WT_QIC02_STAT_RESETMASK & ~WT_QIC02_STAT_EXCEPTION)

/* controller register (QIC02_CTL_PORT) bits */

#define WT_QIC02_CTL_RESET      0x02

#define WT_QIC02_CTL_REQUEST    0x04

#define WT_CTL_ONLINE           0x01

#define WT_CTL_CMDOFF           0xC0 

#define WT_CTL_DMA3             0x10                      /* enable dma chan3 */

#define WT_CTL_DMA1             0x08             /* enable dma chan1 or chan2 */

/* ARCHIVE interface card specifics */

#define AR_QIC02_STAT_PORT      (QIC02_TAPE_PORT+1)

#define AR_QIC02_CTL_PORT       (QIC02_TAPE_PORT+1)

#define AR_QIC02_CMD_PORT       (QIC02_TAPE_PORT)

#define AR_QIC02_DATA_PORT      (QIC02_TAPE_PORT)

#define AR_START_DMA_PORT       (QIC02_TAPE_PORT+2)

#define AR_RESET_DMA_PORT       (QIC02_TAPE_PORT+3)

/* STAT port bits */

#define AR_STAT_IRQF            0x80    /* active high, interrupt request flag */

#define AR_QIC02_STAT_READY     0x40    /* active low */

#define AR_QIC02_STAT_EXCEPTION 0x20    /* active low */

#define AR_QIC02_STAT_MASK      (AR_QIC02_STAT_READY|AR_QIC02_STAT_EXCEPTION)

#define AR_STAT_DMADONE         0x10    /* active high, DMA done */

#define AR_STAT_DIRC            0x08    /* active high, direction */

#define AR_QIC02_STAT_RESETMASK 0x70    /* check RDY,EXC,DMADONE */

#define AR_QIC02_STAT_RESETVAL  ((AR_QIC02_STAT_RESETMASK & ~AR_STAT_IRQF & ~AR_QIC02_STAT_EXCEPTION) | AR_STAT_DMADONE)

/* CTL port bits */

#define AR_QIC02_CTL_RESET      0x80    /* drive reset */

#define AR_QIC02_CTL_REQUEST    0x40    /* notify of new command */

#define AR_CTL_IEN              0x20    /* interrupt enable */

#define AR_CTL_DNIEN            0x10    /* done-interrupt enable */

  /* Note: All of these bits are cleared automatically when writing to

   * AR_RESET_DMA_PORT. So AR_CTL_IEN and AR_CTL_DNIEN must be

   * reprogrammed before the write to AR_START_DMA_PORT.

   */

/* MOUNTAIN interface specifics */

#define MTN_QIC02_STAT_PORT     (QIC02_TAPE_PORT+1)

#define MTN_QIC02_CTL_PORT      (QIC02_TAPE_PORT+1)

#define MTN_QIC02_CMD_PORT      (QIC02_TAPE_PORT)

#define MTN_QIC02_DATA_PORT     (QIC02_TAPE_PORT)

#define MTN_W_SELECT_DMA_PORT   (QIC02_TAPE_PORT+2)

#define MTN_R_DESELECT_DMA_PORT (QIC02_TAPE_PORT+2)

#define MTN_W_DMA_WRITE_PORT    (QIC02_TAPE_PORT+3)

/* STAT port bits */

#define MTN_QIC02_STAT_READY     0x02   /* active low */

#define MTN_QIC02_STAT_EXCEPTION 0x04   /* active low */

#define MTN_QIC02_STAT_MASK      (MTN_QIC02_STAT_READY|MTN_QIC02_STAT_EXCEPTION)

#define MTN_STAT_DMADONE         0x01   /* active high, DMA done */

#define MTN_QIC02_STAT_RESETMASK 0x07   /* check RDY,EXC,DMADONE */

#define MTN_QIC02_STAT_RESETVAL  ((MTN_QIC02_STAT_RESETMASK & ~MTN_QIC02_STAT_EXCEPTION) | MTN_STAT_DMADONE)

  /* CTL port bits */

#define MTN_QIC02_CTL_RESET_NOT  0x80   /* drive reset, active low */

#define MTN_QIC02_CTL_RESET      0x80   /* Fodder #definition to keep gcc happy */

#define MTN_QIC02_CTL_ONLINE     0x40   /* Put drive on line  */

#define MTN_QIC02_CTL_REQUEST    0x20   /* notify of new command */

#define MTN_QIC02_CTL_IRQ_DRIVER 0x10   /* Enable IRQ tristate driver */

#define MTN_QIC02_CTL_DMA_DRIVER 0x08   /* Enable DMA tristate driver */

#define MTN_CTL_EXC_IEN          0x04   /* Exception interrupt enable */

#define MTN_CTL_RDY_IEN          0x02   /* Ready interrupt enable */

#define MTN_CTL_DNIEN            0x01   /* done-interrupt enable */

#define MTN_CTL_ONLINE          (MTN_QIC02_CTL_RESET_NOT | MTN_QIC02_CTL_IRQ_DRIVER | MTN_QIC02_CTL_DMA_DRIVER)

#ifndef CONFIG_QIC02_DYNCONF

# define QIC02_TAPE_DEBUG       (qic02_tape_debug)

# if QIC02_TAPE_IFC == WANGTEK  

#  define QIC02_STAT_PORT       WT_QIC02_STAT_PORT

#  define QIC02_CTL_PORT        WT_QIC02_CTL_PORT

#  define QIC02_CMD_PORT        WT_QIC02_CMD_PORT

#  define QIC02_DATA_PORT       WT_QIC02_DATA_PORT

#  define QIC02_STAT_READY      WT_QIC02_STAT_READY

#  define QIC02_STAT_EXCEPTION  WT_QIC02_STAT_EXCEPTION

#  define QIC02_STAT_MASK       WT_QIC02_STAT_MASK

#  define QIC02_STAT_RESETMASK  WT_QIC02_STAT_RESETMASK

#  define QIC02_STAT_RESETVAL   WT_QIC02_STAT_RESETVAL

#  define QIC02_CTL_RESET       WT_QIC02_CTL_RESET

#  define QIC02_CTL_REQUEST     WT_QIC02_CTL_REQUEST

#  if QIC02_TAPE_DMA == 3

#   ifdef QIC02_TAPE_DMA3_FIX

#    define WT_CTL_DMA          WT_CTL_DMA1

#   else

#    define WT_CTL_DMA          WT_CTL_DMA3

#   endif

#  elif QIC02_TAPE_DMA == 1

#    define WT_CTL_DMA          WT_CTL_DMA1

#  else

#   error Unsupported or incorrect DMA configuration.

#  endif

# elif QIC02_TAPE_IFC == ARCHIVE

#  define QIC02_STAT_PORT       AR_QIC02_STAT_PORT

#  define QIC02_CTL_PORT        AR_QIC02_CTL_PORT

#  define QIC02_CMD_PORT        AR_QIC02_CMD_PORT

#  define QIC02_DATA_PORT       AR_QIC02_DATA_PORT

#  define QIC02_STAT_READY      AR_QIC02_STAT_READY

#  define QIC02_STAT_EXCEPTION  AR_QIC02_STAT_EXCEPTION

#  define QIC02_STAT_MASK       AR_QIC02_STAT_MASK

#  define QIC02_STAT_RESETMASK  AR_QIC02_STAT_RESETMASK

#  define QIC02_STAT_RESETVAL   AR_QIC02_STAT_RESETVAL

#  define QIC02_CTL_RESET       AR_QIC02_CTL_RESET

#  define QIC02_CTL_REQUEST     AR_QIC02_CTL_REQUEST

#  if QIC02_TAPE_DMA > 3        /* channel 2 is used by the floppy driver */

#   error DMA channels other than 1 and 3 are not supported.

#  endif

# elif QIC02_TAPE_IFC == MOUNTAIN

#  define QIC02_STAT_PORT       MTN_QIC02_STAT_PORT

#  define QIC02_CTL_PORT        MTN_QIC02_CTL_PORT

#  define QIC02_CMD_PORT        MTN_QIC02_CMD_PORT

#  define QIC02_DATA_PORT       MTN_QIC02_DATA_PORT

#  define QIC02_STAT_READY      MTN_QIC02_STAT_READY

#  define QIC02_STAT_EXCEPTION  MTN_QIC02_STAT_EXCEPTION

#  define QIC02_STAT_MASK       MTN_QIC02_STAT_MASK

#  define QIC02_STAT_RESETMASK  MTN_QIC02_STAT_RESETMASK

#  define QIC02_STAT_RESETVAL   MTN_QIC02_STAT_RESETVAL

#  define QIC02_CTL_RESET       MTN_QIC02_CTL_RESET

#  define QIC02_CTL_REQUEST     MTN_QIC02_CTL_REQUEST

#  if QIC02_TAPE_DMA > 3        /* channel 2 is used by the floppy driver */

#   error DMA channels other than 1 and 3 are not supported.

#  endif

# else

#  error No valid interface card specified!

# endif /* QIC02_TAPE_IFC */

  /* An ugly hack to make sure WT_CTL_DMA is defined even for the

   * static, non-Wangtek case. The alternative was even worse.

   */

# ifndef WT_CTL_DMA

#  define WT_CTL_DMA            WT_CTL_DMA1

# endif

/*******************/

#else /* !CONFIG_QIC02_DYNCONF */

/* Now the runtime config version, using variables instead of constants.

 *

 * qic02_tape_dynconf is R/O for the kernel, set from userspace.

 * qic02_tape_ccb is private to the driver, R/W.

 */

# define QIC02_TAPE_DRIVE       (qic02_tape_dynconf.mt_type)

# define QIC02_TAPE_IFC         (qic02_tape_ccb.ifc_type)

# define QIC02_TAPE_IRQ         (qic02_tape_dynconf.irqnr)

# define QIC02_TAPE_DMA         (qic02_tape_dynconf.dmanr)

# define QIC02_TAPE_PORT        (qic02_tape_dynconf.port)

# define WT_CTL_DMA             (qic02_tape_ccb.dma_enable_value)

# define QIC02_TAPE_DEBUG       (qic02_tape_dynconf.debug)

# define QIC02_STAT_PORT        (qic02_tape_ccb.port_stat)

# define QIC02_CTL_PORT         (qic02_tape_ccb.port_ctl)

# define QIC02_CMD_PORT         (qic02_tape_ccb.port_cmd)

# define QIC02_DATA_PORT        (qic02_tape_ccb.port_data)

# define QIC02_STAT_READY       (qic02_tape_ccb.stat_ready)

# define QIC02_STAT_EXCEPTION   (qic02_tape_ccb.stat_exception)

# define QIC02_STAT_MASK        (qic02_tape_ccb.stat_mask)

# define QIC02_STAT_RESETMASK   (qic02_tape_ccb.stat_resetmask)

# define QIC02_STAT_RESETVAL    (qic02_tape_ccb.stat_resetval)

# define QIC02_CTL_RESET        (qic02_tape_ccb.ctl_reset)

# define QIC02_CTL_REQUEST      (qic02_tape_ccb.ctl_request)

# define TP_HAVE_DENS           (qic02_tape_dynconf.have_dens)

# define TP_HAVE_BSF            (qic02_tape_dynconf.have_bsf)

# define TP_HAVE_FSR            (qic02_tape_dynconf.have_fsr)

# define TP_HAVE_BSR            (qic02_tape_dynconf.have_bsr)

# define TP_HAVE_EOD            (qic02_tape_dynconf.have_eod)

# define TP_HAVE_SEEK           (qic02_tape_dynconf.have_seek)

# define TP_HAVE_TELL           (qic02_tape_dynconf.have_tell)

# define TP_HAVE_RAS1           (qic02_tape_dynconf.have_ras1)

# define TP_HAVE_RAS2           (qic02_tape_dynconf.have_ras2)

#endif /* CONFIG_QIC02_DYNCONF */

/* "Vendor Unique" codes */

/* Archive seek & tell stuff */

#define AR_QCMDV_TELL_BLK       0xAE    /* read current block address */

#define AR_QCMDV_SEEK_BLK       0xAD    /* seek to specific block */

#define AR_SEEK_BUF_SIZE        3       /* address is 3 bytes */

/*

 * Misc common stuff

 */

/* Standard QIC-02 commands -- rev F.  All QIC-02 drives must support these */

#define QCMD_SEL_1      0x01            /* select drive 1 */

#define QCMD_SEL_2      0x02            /* select drive 2 */

#define QCMD_SEL_3      0x04            /* select drive 3 */

#define QCMD_SEL_4      0x08            /* select drive 4 */

#define QCMD_REWIND     0x21            /* rewind tape */

#define QCMD_ERASE      0x22            /* erase tape */

#define QCMD_RETEN      0x24            /* retension tape */

#define QCMD_WRT_DATA   0x40            /* write data */

#define QCMD_WRT_FM     0x60            /* write file mark */

#define QCMD_RD_DATA    0x80            /* read data */

#define QCMD_RD_FM      0xA0            /* read file mark (forward direction) */

#define QCMD_RD_STAT    0xC0            /* read status */

/* Other (optional/vendor unique) commands */

 /* Density commands are only valid when TP_BOM is set! */

#define QCMD_DENS_11    0x26            /* QIC-11 */

#define QCMD_DENS_24    0x27            /* QIC-24: 9 track 60MB */

#define QCMD_DENS_120   0x28            /* QIC-120: 15 track 120MB */

#define QCMD_DENS_150   0x29            /* QIC-150: 18 track 150MB */

#define QCMD_DENS_300   0x2A            /* QIC-300/QIC-2100 */

#define QCMD_DENS_600   0x2B            /* QIC-600/QIC-2200 */

/* don't know about QIC-1000 and QIC-1350 */

#define QCMD_WRTNU_DATA 0x40            /* write data, no underruns, insert filler. */

#define QCMD_SPACE_FWD  0x81            /* skip next block */

#define QCMD_SPACE_BCK  0x89            /* move tape head one block back -- very useful! */

#define QCMD_RD_FM_BCK  0xA8            /* read filemark (backwards) */

#define QCMD_SEEK_EOD   0xA3            /* skip to EOD */

#define QCMD_RD_STAT_X1 0xC1            /* read extended status 1 */

#define QCMD_RD_STAT_X2 0xC4            /* read extended status 2 */

#define QCMD_RD_STAT_X3 0xE0            /* read extended status 3 */

#define QCMD_SELF_TST1  0xC2            /* run self test 1 (nondestructive) */

#define QCMD_SELF_TST2  0xCA            /* run self test 2 (destructive) */

/* Optional, QFA (Quick File Access) commands.

 * Not all drives support this, but those that do could use these commands

 * to implement semi-non-sequential access. `mt fsf` would benefit from this.

 * QFA divides the tape into 2 partitions, a data and a directory partition,

 * causing some incompatibility problems wrt std QIC-02 data exchange.

 * It would be useful to cache the directory info, but that might be tricky

 * to do in kernel-space. [Size constraints.]

 * Refer to the QIC-02 specs, appendix A for more information.

 * I have no idea how other *nix variants implement QFA.

 * I have no idea which drives support QFA and which don't.

 */

#define QFA_ENABLE      0x2D            /* enter QFA mode, give @ BOT only */

#define QFA_DATA        0x20            /* select data partition */

#define QFA_DIR         0x23            /* select directory partition */

#define QFA_RD_POS      0xCF            /* read position+status bytes */

#define QFA_SEEK_EOD    0xA1            /* seek EOD within current partition */

#define QFA_SEEK_BLK    0xAF            /* seek to a block within current partition */

/*

 * Debugging flags

 */

#define TPQD_SENSE_TEXT 0x0001

#define TPQD_SENSE_CNTS 0x0002

#define TPQD_REWIND     0x0004

#define TPQD_TERM_CYCLE 0x0008

#define TPQD_IOCTLS     0x0010

#define TPQD_DMAX       0x0020

#define TPQD_BLKSZ      0x0040

#define TPQD_MISC       0x0080

#define TPQD_DEBUG      0x0100

#define TPQD_DIAGS      0x1000

#define TPQD_ALWAYS     0x8000

#define TPQD_DEFAULT_FLAGS      0x00fc

#define TPQDBG(f)       ((QIC02_TAPE_DEBUG) & (TPQD_##f))

/* Minor device codes for tapes:

 * |7|6|5|4|3|2|1|0|

 *  | \ | / \ | / |_____ 1=rewind on close, 0=no rewind on close

 *  |  \|/    |_________ Density: 000=none, 001=QIC-11, 010=24, 011=120,

 *  |   |                100=QIC-150, 101..111 reserved.

 *  |   |_______________ Reserved for unit numbers.

 *  |___________________ Reserved for diagnostics during debugging.

 */

#define TP_REWCLOSE(d)  ((MINOR(d)&0x01) == 1)                  /* rewind bit */

                           /* rewind is only done if data has been transfered */

#define TP_DENS(dev)    ((MINOR(dev) >> 1) & 0x07)            /* tape density */

#define TP_UNIT(dev)    ((MINOR(dev) >> 4) & 0x07)             /* unit number */

/* print excessive diagnostics */

#define TP_DIAGS(dev)   (QIC02_TAPE_DEBUG & TPQD_DIAGS)

/* status codes returned by a WTS_RDSTAT call */

struct tpstatus {       /* sizeof(short)==2), LSB first */

        unsigned short  exs;    /* Drive exception flags */

        unsigned short  dec;    /* data error count: nr of blocks rewritten/soft read errors */

        unsigned short  urc;    /* underrun count: nr of times streaming was interrupted */

};

#define TPSTATSIZE      sizeof(struct tpstatus)

/* defines for tpstatus.exs -- taken from 386BSD wt driver */

#define TP_POR          0x100   /* Power on or reset occurred */

#define TP_EOR          0x200   /* REServed for end of RECORDED media */

#define TP_PAR          0x400   /* REServed for bus parity */

#define TP_BOM          0x800   /* Beginning of media */

#define TP_MBD          0x1000  /* Marginal block detected */

#define TP_NDT          0x2000  /* No data detected */

#define TP_ILL          0x4000  /* Illegal command */

#define TP_ST1          0x8000  /* Status byte 1 flag */

#define TP_FIL          0x01    /* File mark detected */

#define TP_BNL          0x02    /* Bad block not located */

#define TP_UDA          0x04    /* Unrecoverable data error */

#define TP_EOM          0x08    /* End of media */

#define TP_WRP          0x10    /* Write protected cartridge */

#define TP_USL          0x20    /* Unselected drive */

#define TP_CNI          0x40    /* Cartridge not in place */

#define TP_ST0          0x80    /* Status byte 0 flag */

#define REPORT_ERR0     (TP_CNI|TP_USL|TP_WRP|TP_EOM|TP_UDA|TP_BNL|TP_FIL)

#define REPORT_ERR1     (TP_ILL|TP_NDT|TP_MBD|TP_PAR)

/* exception numbers */

#define EXC_UNKNOWN     0        /* (extra) Unknown exception code */

#define EXC_NDRV        1       /* No drive */

#define EXC_NCART       2       /* No cartridge */

#define EXC_WP          3       /* Write protected */

#define EXC_EOM         4       /* EOM */

#define EXC_RWA         5       /* read/write abort */

#define EXC_XBAD        6       /* read error, bad block transfered */

#define EXC_XFILLER     7       /* read error, filler block transfered */

#define EXC_NDT         8       /* read error, no data */

#define EXC_NDTEOM      9       /* read error, no data & EOM */

#define EXC_NDTBOM      10      /* read error, no data & BOM */

#define EXC_FM          11      /* Read a filemark */

#define EXC_ILL         12      /* Illegal command */

#define EXC_POR         13      /* Power on/reset */

#define EXC_MARGINAL    14      /* Marginal block detected */

#define EXC_EOR         15      /* (extra, for SEEKEOD) End Of Recorded data reached */

#define EXC_BOM         16      /* (extra) BOM reached */

#define TAPE_NOTIFY_TIMEOUT     1000000

/* internal function return codes */

#define TE_OK   0                /* everything is fine */

#define TE_EX   1               /* exception detected */

#define TE_ERR  2               /* some error */

#define TE_NS   3               /* can't read status */

#define TE_TIM  4               /* timed out */

#define TE_DEAD 5               /* tape drive doesn't respond */

#define TE_END  6               /******** Archive hack *****/

/* timeout timer values -- check these! */

#define TIM_S   (4*HZ)          /* 4 seconds (normal cmds) */

#define TIM_M   (30*HZ)         /* 30 seconds (write FM) */

#define TIM_R   (8*60*HZ)       /* 8 minutes (retensioning) */

#define TIM_F   (2*3600*HZ)     /* est. 1.2hr for full tape read/write+2 retens */

#define TIMERON(t)      timer_table[QIC02_TAPE_TIMER].expires = jiffies + (t); \

                        timer_active |= (1<<QIC02_TAPE_TIMER)

#define TIMEROFF        timer_active &= ~(1<<QIC02_TAPE_TIMER)

#define TIMERCONT       timer_active |= (1<<QIC02_TAPE_TIMER)

typedef char flag;

#define NO      0        /* NO must be 0 */

#define YES     1       /* YES must be != 0 */

#ifdef TDEBUG

# define TPQDEB(s)      s

# define TPQPUTS(s)     tpqputs(s)

#else

# define TPQDEB(s)

# define TPQPUTS(s)

#endif

/* NR_BLK_BUF is a `tuneable parameter'. If you're really low on

 * kernel space, you could decrease it to 1, or if you got a very

 * slow machine, you could increase it up to 128 blocks. Less kernel

 * buffer blocks result in more context-switching.

 */

#define NR_BLK_BUF      20                                  /* max 128 blocks */

#define TAPE_BLKSIZE    512               /* streamer tape block size (fixed) */

#define TPQBUF_SIZE     (TAPE_BLKSIZE*NR_BLK_BUF)              /* buffer size */

#define BLOCKS_BEYOND_EW        2       /* nr of blocks after Early Warning hole */

#define BOGUS_IRQ               32009

/* This is internal data, filled in based on the ifc_type field given

 * by the user. Everex is mapped to Wangtek with a different

 * `dma_enable_value', if dmanr==3.

 */

struct qic02_ccb {

        long    ifc_type;

        unsigned short  port_stat;      /* Status port address */

        unsigned short  port_ctl;       /* Control port address */

        unsigned short  port_cmd;       /* Command port address */

        unsigned short  port_data;      /* Data port address */

        /* status register bits */

        unsigned short  stat_ready;     /* drive ready */

        unsigned short  stat_exception; /* drive signals exception */

        unsigned short  stat_mask;

        unsigned short  stat_resetmask;

        unsigned short  stat_resetval;

        /* control register bits */

        unsigned short  ctl_reset;      /* reset drive */

        unsigned short  ctl_request;    /* latch command */

        /* This is used to change the DMA3 behaviour */

        unsigned short  dma_enable_value;

};

extern int qic02_tape_init(void);                         /* for mem.c */

#endif /* CONFIG_QIC02_TAPE */

#endif /* _LINUX_TPQIC02_H */