Subversion Repositories or1k_old

                    LINUX DRIVER FOR BAYCOM MODEMS

       Thomas M. Sailer, HB9JNX/AE4WA, 

This document describes the Linux Kernel Driver for simple Baycom style

amateur radio modems. The driver supports the following modems:

ser12:  This is a very simple 1200 baud AFSK modem. The modem consists only

        of a modulator/demodulator chip, usually a TI TCM3105. The computer

        is responsible for regenerating the receiver bit clock, as well as

        for handling the HDLC protocol. The modem connects to a serial port,

        hence the name. Since the serial port is not used as an async serial

        port, the kernel driver for serial ports cannot be used, and this

        driver only supports standard serial hardware (8250, 16450, 16550)

par96:  This is a modem for 9600 baud FSK compatible to the G3RUH standard.

        The modem does all the filtering and regenerates the receiver clock.

        Data is transferred from and to the PC via a shift register.

        The shift register is filled with 16 bits and an interrupt is signalled.

        The PC then empties the shift register in a burst. This modem connects

        to the parallel port, hence the name. The modem leaves the

        implementation of the HDLC protocol and the scrambler polynomial to

        the PC.

picpar: This is a redesign of the par96 modem by Henning Rech, DF9IC. The modem

        is protocol compatible to par96, but uses only three low power ICs

        and can therefore be fed from the parallel port and does not require

        an additional power supply. Furthermore, it incorporates a carrier

        detect circuitry.

All of the above modems only support half duplex communications. However,

the driver supports the KISS (see below) fullduplex command. It then simply

starts to send as soon as there's a packet to transmit and does not care

about DCD, i.e. it starts to send even if there's someone else on the channel.

This command is required by some implementations of the DAMA channel

access protocol.

The Interface of the driver

Unlike previous drivers, the driver is no longer a character device,

but it is now a true kernel network interface. Installation is therefore

simple. Once installed, four interfaces named bc[0-3] are available.

sethdlc from the ax25 utilities may be used to set driver states etc.

Users of userland AX.25 stacks may use the net2kiss utility (also available

in the ax25 utilities package) to converts packets of a network interface

to a KISS stream on a pseudo tty. There's also a patch available from

me for WAMPES which allows attaching a kernel network interface directly.

Configuring the driver

Every time the driver is inserted into the kernel, it has to know which

modems it should access at which ports. This can be done with the setbaycom

utility. If you are only using one modem, you can also configure the

driver from the insmod command line (or by means of an option line in

/etc/conf.modules).

Examples: (use either method, not both)

  insmod baycom mode="ser12*" iobase=0x3f8 irq=4

  sethdlc -i bc0 -p type "ser12*" io 0x3f8 irq 4

Both lines configure the first port to drive a ser12 modem at the first

serial port (COM1 under DOS). The star ('*') instructs the driver to use

the software DCD algorithm (see below).

  insmod baycom mode="par96*" iobase=0x378 irq=7

  sethdlc -i bc0 -p type "par96*" io 0x378 irq 7

Both lines configure the first port to drive a par96 or par97 modem at the

first parallel port (LPT1 under DOS). options=1 instructs the driver to use

the software DCD algorithm (see below).

  insmod baycom mode="par96" iobase=0x278 irq=5

  sethdlc -i bc0 -p type "par96" io 0x278 irq 5

Both lines configure the first port to drive a picpar modem at the

second parallel port (LPT2 under DOS). The driver uses the hardware DCD

signalled by the picpar modem (see below).

The channel access parameters can be set with sethdlc -a or kissparms.

Note that both utilities interpret the values slightly different.

Hardware DCD versus Software DCD

To avoid collisions on the air, the driver must know when the channel is

busy. This is the task of the DCD circuitry/software. The driver may either

utilise a software DCD algorithm (a star after the mode string) or use a DCD

signal from the hardware (no star).

ser12:  if software DCD is utilised, the radio's squelch should always be

        open. It is highly recommended to use the software DCD algorithm,

        as it is much faster than most hardware squelch circuitry. The

        disadvantage is a slightly higher load on the system.

par96:  the software DCD algorithm for this type of modem is rather poor.

        The modem simply does not provide enough information to implement

        a reasonable DCD algorithm in software. Therefore, if your radio

        feeds the DCD input of the par96 modem, the use of the hardware

        DCD circuitry is recommended.

picpar: the picpar modem features a builtin DCD hardware, which is highly

        recommended.

Compatibility with the rest of the Linux kernel

The serial driver, the line printer (lp) driver and the baycom driver compete

for the same hardware resources. Of course only one driver can access a given

interface at a time. The serial driver grabs all interfaces it can find at

startup time. Therefore the baycom driver subsequently won't be able to

access a serial port. You might therefore find it necessary to release

a port owned by the serial driver with 'setserial /dev/ttyS# uart none', where

# is the number of the interface. The baycom driver does not reserve any

port at startup, unless one is specified on the 'insmod' command line. Another

method to solve the problem is to compile all three drivers as modules and

leave it to kerneld to load the correct driver depending on the application.

Further reading

Please take a look at http://www.ife.ee.ethz.ch/~sailer/ham/linux/hdlc.html

for further informations on the driver.

vy 73s de

Tom Sailer, sailer@ife.ee.ethz.ch

Packet Radio: hb9jnx@hb9w.che.eu