Subversion Repositories pit

////////////////////////////////////////////////////////////////////////////////

//

//  WISHBONE revB.2 compliant Programable Interval Timer - Test Bench

//

//  Author: Bob Hayes

//          rehayes@opencores.org

//

//  Downloaded from: http://www.opencores.org/projects/pit.....

//

////////////////////////////////////////////////////////////////////////////////

// Copyright (c) 2009, Robert Hayes

//

// All rights reserved.

//

// Redistribution and use in source and binary forms, with or without

// modification, are permitted provided that the following conditions are met:

//     * Redistributions of source code must retain the above copyright

//       notice, this list of conditions and the following disclaimer.

//     * Redistributions in binary form must reproduce the above copyright

//       notice, this list of conditions and the following disclaimer in the

//       documentation and/or other materials provided with the distribution.

//     * Neither the name of the <organization> nor the

//       names of its contributors may be used to endorse or promote products

//       derived from this software without specific prior written permission.

//

// THIS SOFTWARE IS PROVIDED BY Robert Hayes ''AS IS'' AND ANY

// EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

// WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

// DISCLAIMED. IN NO EVENT SHALL Robert Hayes BE LIABLE FOR ANY

// DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

// (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

// LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND

// ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

// SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

////////////////////////////////////////////////////////////////////////////////

// 45678901234567890123456789012345678901234567890123456789012345678901234567890

`include "timescale.v"

module tst_bench_top();

        //

        // wires && regs

        //

        reg        mstr_test_clk;

        reg [19:0] vector;

        reg [ 7:0] test_num;

        reg        rstn;

        reg        sync_reset;

        wire [31:0] adr;

        wire [15:0] dat_i, dat_o, dat0_i, dat1_i, dat2_i, dat3_i;

        wire we;

        wire stb;

        wire cyc;

        wire ack;

        wire inta_1, inta_2, inta_3, inta_4;

        wire count_en_1;

        wire count_flag_1;

        reg [15:0] q, qq;

        wire scl, scl0_o, scl0_oen, scl1_o, scl1_oen;

        wire sda, sda0_o, sda0_oen, sda1_o, sda1_oen;

        // Name Address Locations

        parameter PIT_CNTRL = 5'b0_0000;

        parameter PIT_MOD   = 5'b0_0001;

        parameter PIT_COUNT = 5'b0_0010;

        parameter RD      = 1'b1;

        parameter WR      = 1'b0;

        parameter SADR    = 7'b0010_000;

        parameter CTR_EN  = 8'b1000_0000;  // core enable bit

        parameter CTR_IEN = 8'b0100_0000;  // core interrupt enable bit

        parameter PIT_CNTRL_SLAVE  = 16'h8000;  // PIT Slave mode

        parameter PIT_CNTRL_FLAG   = 16'h0004;  // PIT Rollover Flag

        parameter PIT_CNTRL_IRQEN  = 16'h0002;  // PIT Interupt Enable

        parameter PIT_CNTRL_ENA    = 16'h0001;  // PIT Enable

        parameter SLAVE_0_CNTRL = 5'b0_1000;

        parameter SLAVE_0_MOD   = 5'b0_1001;

        parameter SLAVE_0_COUNT = 5'b0_1010;

        parameter SLAVE_1_CNTRL = 5'b1_0000;

        parameter SLAVE_1_MOD   = 5'b1_0001;

        parameter SLAVE_1_COUNT = 5'b1_0010;

        parameter SLAVE_2_CNTRL_0 = 5'b1_1000;

        parameter SLAVE_2_CNTRL_1 = 5'b1_1001;

        parameter SLAVE_2_MOD_0   = 5'b1_1010;

        parameter SLAVE_2_MOD_1   = 5'b1_1011;

        parameter SLAVE_2_COUNT_0 = 5'b1_1100;

        parameter SLAVE_2_COUNT_1 = 5'b1_1101;

        // initial values and testbench setup

        initial

          begin

            mstr_test_clk = 0;

            vector = 0;

            test_num = 0;

            `ifdef WAVES

                 $shm_open("waves");

                 $shm_probe("AS",tst_bench_top,"AS");

                 $display("\nINFO: Signal dump enabled ...\n\n");

              `endif

              `ifdef WAVES_V

                 $dumpfile ("pit_wave_dump.lxt");

                 $dumpvars (0, tst_bench_top);

                 $dumpon;

                 $display("\nINFO: VCD Signal dump enabled ...\n\n");

              `endif

          end

        // generate clock

        always #20 mstr_test_clk = ~mstr_test_clk;

        always @(posedge mstr_test_clk)

          vector = vector + 1;

        // hookup wishbone master model

        wb_master_model #(.dwidth(16), .awidth(32))

                u0 (

                .clk(mstr_test_clk),

                .rst(rstn),

                .adr(adr),

                .din(dat_i),

                .dout(dat_o),

                .cyc(cyc),

                .stb(stb),

                .we(we),

                .sel(),

                .ack(ack),

                .err(1'b0),

                .rty(1'b0)

        );

        // Address decoding for different PIT module instances

        wire stb0 = stb && ~adr[4] && ~adr[3];

        wire stb1 = stb && ~adr[4] &&  adr[3];

        wire stb2 = stb &&  adr[4] && ~adr[3];

        wire stb3 = stb &&  adr[4] &&  adr[3];

        // Create the Read Data Bus

        assign dat_i = ({16{stb0}} & dat0_i) |

                       ({16{stb1}} & dat1_i) |

                       ({16{stb2}} & dat2_i) |

                       ({16{stb3}} & {8'b0, dat3_i[7:0]});

        // hookup wishbone_PIT_master core - Parameters take all default values

        //  Async Reset, 16 bit Bus, 16 bit Granularity

        pit_top pit_1(

                // wishbone interface

                .wb_clk_i(mstr_test_clk),

                .wb_rst_i(1'b0),

                .arst_i(rstn),

                .wb_adr_i(adr[2:0]),

                .wb_dat_i(dat_o),

                .wb_dat_o(dat0_i),

                .wb_we_i(we),

                .wb_stb_i(stb0),

                .wb_cyc_i(cyc),

                .wb_sel_i( 2'b11 ),

                .wb_ack_o(ack),

                .pit_irq_o(inta_1),

                .pit_o(pit_1_out),

                .ext_sync_i(1'b0),

                .cnt_sync_o(count_en_1),

                .cnt_flag_o(count_flag_1)

        );

        // hookup wishbone_PIT_slave core - Parameters take all default values

        //  Sync Reset, 16 bit Bus, 16 bit Granularity

        pit_top #(.ARST_LVL(1'b1))

                pit_2(

                // wishbone interface

                .wb_clk_i(mstr_test_clk),

                .wb_rst_i(sync_reset),

                .arst_i(1'b0),

                .wb_adr_i(adr[2:0]),

                .wb_dat_i(dat_o),

                .wb_dat_o(dat1_i),

                .wb_we_i(we),

                .wb_stb_i(stb1),

                .wb_cyc_i(cyc),

                .wb_sel_i( 2'b11 ),

                .wb_ack_o(ack),

                .pit_irq_o(inta_2),

                .pit_o(pit_2_out),

                .ext_sync_i(count_en_1),

                .cnt_sync_o(count_en_2),

                .cnt_flag_o(count_flag_2)

        );

        // hookup wishbone_PIT_slave core

        //  16 bit Bus, 16 bit Granularity

        pit_top #(.NO_PRESCALE(1'b1))

                pit_3(

                // wishbone interface

                .wb_clk_i(mstr_test_clk),

                .wb_rst_i(sync_reset),

                .arst_i(1'b1),

                .wb_adr_i(adr[2:0]),

                .wb_dat_i(dat_o),

                .wb_dat_o(dat2_i),

                .wb_we_i(we),

                .wb_stb_i(stb2),

                .wb_cyc_i(cyc),

                .wb_sel_i( 2'b11 ),

                .wb_ack_o(ack),

                .pit_irq_o(inta_3),

                .pit_o(pit_3_out),

                .ext_sync_i(count_en_1),

                .cnt_sync_o(count_en_3),

                .cnt_flag_o(count_flag_3)

        );

        // hookup wishbone_PIT_slave core

        //  8 bit Bus, 8 bit Granularity

        pit_top #(.DWIDTH(8))

                pit_4(

                // wishbone interface

                .wb_clk_i(mstr_test_clk),

                .wb_rst_i(sync_reset),

                .arst_i(1'b1),

                .wb_adr_i(adr[2:0]),

                .wb_dat_i(dat_o[7:0]),

                .wb_dat_o(dat3_i[7:0]),

                .wb_we_i(we),

                .wb_stb_i(stb3),

                .wb_cyc_i(cyc),

                .wb_sel_i( 2'b11 ),

                .wb_ack_o(ack),

                .pit_irq_o(inta_4),

                .pit_o(pit_4_out),

                .ext_sync_i(count_en_1),

                .cnt_sync_o(count_en_4),

                .cnt_flag_o(count_flag_4)

        );

// Test Program

initial

  begin

      $display("\nstatus: %t Testbench started", $time);

      // reset system

      rstn = 1'b1; // negate reset

      repeat(1) @(posedge mstr_test_clk);

      sync_reset = 1'b1;  // Make the sync reset 1 clock cycle long

      #2;          // move the async reset away from the clock edge

      rstn = 1'b0; // assert async reset

      #5;          // Keep the async reset pulse with less than a clock cycle

      rstn = 1'b1; // negate async reset

      repeat(1) @(posedge mstr_test_clk);

      sync_reset = 1'b0;

      $display("\nstatus: %t done reset", $time);

      test_num = test_num + 1;

      repeat(2) @(posedge mstr_test_clk);

      //

      // program core

      //

      reg_test_16;

      reg_test_8;

      u0.wb_write(1, SLAVE_0_CNTRL,   PIT_CNTRL_SLAVE); // Enable Slave Mode

      u0.wb_write(1, SLAVE_1_CNTRL,   PIT_CNTRL_SLAVE); // Enable Slave Mode

      u0.wb_write(1, SLAVE_2_CNTRL_1, 16'h0080); // Enable Slave Mode

      u0.wb_write(1, SLAVE_0_MOD,     16'h000a); // load Modulo

      u0.wb_write(1, SLAVE_1_MOD,     16'h0010); // load Modulo

      u0.wb_write(1, SLAVE_2_MOD_0,   16'h0010); // load Modulo

      // Set Master Mode PS=0, Modulo=16

      test_num = test_num + 1;

      $display("TEST #%d Starts at vector=%d, ms_test", test_num, vector);

      u0.wb_write(1, PIT_MOD,   16'h0010); // load prescaler hi-byte

      u0.wb_write(1, PIT_CNTRL, PIT_CNTRL_ENA); // Enable to start counting

      $display("status: %t programmed registers", $time);

      wait_flag_set;  // Wait for Counter to tomeout

      u0.wb_write(1, PIT_CNTRL, PIT_CNTRL_FLAG | PIT_CNTRL_ENA); //

      wait_flag_set;  // Wait for Counter to tomeout

      u0.wb_write(1, PIT_CNTRL, PIT_CNTRL_FLAG | PIT_CNTRL_ENA); //

      repeat(10) @(posedge mstr_test_clk);

      u0.wb_write(1, PIT_CNTRL, 16'b0); //

      repeat(10) @(posedge mstr_test_clk);

      mstr_psx_modx(2,4);

      mstr_psx_modx(4,0);

      repeat(100) @(posedge mstr_test_clk);

      $display("\nTestbench done at vector=%d\n", vector);

      $finish;

  end

// Poll for flag set

task wait_flag_set;

  begin

    u0.wb_read(1, PIT_CNTRL, q);

    while(~|(q & PIT_CNTRL_FLAG))

      u0.wb_read(1, PIT_CNTRL, q); // poll it until it is set

    $display("PIT Flag set detected at vector =%d", vector);

  end

endtask

// check register bits - reset, read/write

task reg_test_16;

  begin

      test_num = test_num + 1;

      $display("TEST #%d Starts at vector=%d, reg_test_16", test_num, vector);

      u0.wb_cmp(0, PIT_CNTRL, 16'h4000);   // verify reset

      u0.wb_cmp(0, PIT_MOD,   16'h0000);   // verify reset

      u0.wb_cmp(0, PIT_COUNT, 16'h0001);   // verify reset

      u0.wb_write(1, PIT_CNTRL, 16'hfffe); // load prescaler lo-byte

      u0.wb_cmp(  0, PIT_CNTRL, 16'hCf02); // verify write data

      u0.wb_write(1, PIT_CNTRL, 16'h0000); // load prescaler lo-byte

      u0.wb_cmp(  0, PIT_CNTRL, 16'h4000); // verify write data

      u0.wb_write(1, PIT_MOD, 16'h5555); // load prescaler lo-byte

      u0.wb_cmp(  0, PIT_MOD, 16'h5555); // verify write data

      u0.wb_write(1, PIT_MOD, 16'haaaa); // load prescaler lo-byte

      u0.wb_cmp(  0, PIT_MOD, 16'haaaa); // verify write data

      u0.wb_write(0, PIT_COUNT, 16'hfffe);

      u0.wb_cmp(  0, PIT_COUNT, 16'h0001); // verify register not writable

  end

endtask

task reg_test_8;

  begin

      test_num = test_num + 1;

      $display("TEST #%d Starts at vector=%d, reg_test_8", test_num, vector);

      u0.wb_cmp(0, SLAVE_2_CNTRL_0, 16'h0000);   // verify reset

      u0.wb_cmp(0, SLAVE_2_CNTRL_1, 16'h0040);   // verify reset

      u0.wb_cmp(0, SLAVE_2_MOD_0,   16'h0000);   // verify reset

      u0.wb_cmp(0, SLAVE_2_MOD_1,   16'h0000);   // verify reset

      u0.wb_cmp(0, SLAVE_2_COUNT_0, 16'h0001);   // verify reset

      u0.wb_cmp(0, SLAVE_2_COUNT_1, 16'h0000);   // verify reset

      u0.wb_write(1, SLAVE_2_CNTRL_0, 16'hfffe); // load prescaler lo-byte

      u0.wb_cmp(  0, SLAVE_2_CNTRL_0, 16'h0002); // verify write data

      u0.wb_write(1, SLAVE_2_CNTRL_0, 16'h0000); // load prescaler lo-byte

      u0.wb_cmp(  0, SLAVE_2_CNTRL_0, 16'h0000); // verify write data

      u0.wb_cmp(  0, SLAVE_2_CNTRL_1, 16'h0040); // verify write data

      u0.wb_write(1, SLAVE_2_MOD_0, 16'hff55); // load prescaler lo-byte

      u0.wb_cmp(  0, SLAVE_2_MOD_0, 16'h0055); // verify write data

      u0.wb_write(1, SLAVE_2_MOD_0, 16'hffaa); // load prescaler lo-byte

      u0.wb_cmp(  0, SLAVE_2_MOD_0, 16'h00aa); // verify write data

      u0.wb_write(1, SLAVE_2_MOD_1, 16'hff66); // load prescaler lo-byte

      u0.wb_cmp(  0, SLAVE_2_MOD_1, 16'h0066); // verify write data

      u0.wb_write(1, SLAVE_2_MOD_1, 16'hff99); // load prescaler lo-byte

      u0.wb_cmp(  0, SLAVE_2_MOD_1, 16'h0099); // verify write data

      u0.wb_write(1, SLAVE_2_MOD_1, 16'hff00); // load prescaler lo-byte

      u0.wb_write(0, SLAVE_2_COUNT_0, 16'hfffe);

      u0.wb_cmp(  0, SLAVE_2_COUNT_0, 16'h0001); // verify register not writable

      u0.wb_write(0, SLAVE_2_COUNT_1, 16'hfffe);

      u0.wb_cmp(  0, SLAVE_2_COUNT_1, 16'h0000); // verify register not writable

  end

endtask

task mstr_psx_modx;

  input [ 3:0] ps_val;

  input [15:0] mod_val;

  reg   [15:0] cntrl_val;

  begin

      test_num = test_num + 1;

      $display("TEST #%d Starts at vector=%d, mstr_psx_modx Pre=%h, Mod=%h",

                test_num, vector, ps_val, mod_val);

      // program internal registers

      cntrl_val = {1'b0, 3'b0, ps_val, 8'b0} | PIT_CNTRL_IRQEN;

      u0.wb_write(1, PIT_MOD,   mod_val); // load modulo

      u0.wb_write(1, PIT_CNTRL, ( cntrl_val | PIT_CNTRL_ENA)); // Enable to start counting

      wait_flag_set;  // Wait for Counter to timeout

      u0.wb_write(1, PIT_CNTRL, cntrl_val | PIT_CNTRL_FLAG | PIT_CNTRL_ENA); //

      wait_flag_set;  // Wait for Counter to timeout

      u0.wb_write(1, PIT_CNTRL, cntrl_val | PIT_CNTRL_FLAG | PIT_CNTRL_ENA); //

      repeat(10) @(posedge mstr_test_clk);

      u0.wb_write(1, PIT_CNTRL, 16'b0); //

   end

endtask

endmodule  // tst_bench_top