Subversion Repositories plasma

---------------------------------------------------------------------

-- TITLE: Plamsa Interface (clock divider and interface to FPGA board)

-- AUTHOR: Steve Rhoads (rhoadss@yahoo.com)

-- DATE CREATED: 9/15/07

-- FILENAME: plasma_3e.vhd

-- PROJECT: Plasma CPU core

-- COPYRIGHT: Software placed into the public domain by the author.

--    Software 'as is' without warranty.  Author liable for nothing.

-- DESCRIPTION:

--    This entity divides the clock by two and interfaces to the 

--    Xilinx Spartan-3E XC3S200FT256-4 FPGA with DDR.

---------------------------------------------------------------------

library ieee;

use ieee.std_logic_1164.all;

use ieee.std_logic_unsigned.all;

use ieee.std_logic_arith.all;

--use work.mlite_pack.all;

entity plasma_3e is

   port(CLK_50MHZ  : in std_logic;

        RS232_DCE_RXD : in std_logic;

        RS232_DCE_TXD : out std_logic;

        SD_CK_P    : out std_logic;     --DDR SDRAM clock_positive

        SD_CK_N    : out std_logic;     --clock_negative

        SD_CKE     : out std_logic;     --clock_enable

        SD_BA      : out std_logic_vector(1 downto 0);  --bank_address

        SD_A       : out std_logic_vector(12 downto 0); --address(row or col)

        SD_CS      : out std_logic;     --chip_select

        SD_RAS     : out std_logic;     --row_address_strobe

        SD_CAS     : out std_logic;     --column_address_strobe

        SD_WE      : out std_logic;     --write_enable

        SD_DQ      : inout std_logic_vector(15 downto 0); --data

        SD_UDM     : out std_logic;     --upper_byte_enable

        SD_UDQS    : inout std_logic;   --upper_data_strobe

        SD_LDM     : out std_logic;     --low_byte_enable

        SD_LDQS    : inout std_logic;   --low_data_strobe

        E_MDC      : out std_logic;     --Ethernet PHY

        E_MDIO     : inout std_logic;   --management data in/out

        E_RX_CLK   : in std_logic;      --receive clock

        E_RX_DV    : in std_logic;      --data valid

        E_RXD      : in std_logic_vector(3 downto 0);

        E_TX_CLK   : in std_logic;      --transmit clock

        E_TX_EN    : out std_logic;     --data valid

        E_TXD      : out std_logic_vector(3 downto 0);

        SF_CE0     : out std_logic;     --NOR flash

        SF_OE      : out std_logic;

        SF_WE      : out std_logic;

        SF_BYTE    : out std_logic;

        SF_STS     : in std_logic;      --status

        SF_A       : out std_logic_vector(24 downto 0);

        SF_D       : inout std_logic_vector(15 downto 1);

        SPI_MISO   : inout std_logic;

        VGA_VSYNC  : out std_logic;     --VGA port

        VGA_HSYNC  : out std_logic;

        VGA_RED    : out std_logic;

        VGA_GREEN  : out std_logic;

        VGA_BLUE   : out std_logic;

        PS2_CLK    : in std_logic;      --Keyboard

        PS2_DATA   : in std_logic;

        LED        : out std_logic_vector(7 downto 0);

        ROT_CENTER : in std_logic;

        ROT_A      : in std_logic;

        ROT_B      : in std_logic;

        BTN_EAST   : in std_logic;

        BTN_NORTH  : in std_logic;

        BTN_SOUTH  : in std_logic;

        BTN_WEST   : in std_logic;

        SW         : in std_logic_vector(3 downto 0));

end; --entity plasma_if

architecture logic of plasma_3e is

   component plasma

      generic(memory_type : string := "XILINX_16X"; --"DUAL_PORT_" "ALTERA_LPM";

              log_file    : string := "UNUSED";

              ethernet    : std_logic := '0';

              use_cache   : std_logic := '0');

      port(clk          : in std_logic;

           reset        : in std_logic;

           uart_write   : out std_logic;

           uart_read    : in std_logic;

           address      : out std_logic_vector(31 downto 2);

           byte_we      : out std_logic_vector(3 downto 0);

           data_write   : out std_logic_vector(31 downto 0);

           data_read    : in std_logic_vector(31 downto 0);

           mem_pause_in : in std_logic;

           no_ddr_start : out std_logic;

           no_ddr_stop  : out std_logic;

           gpio0_out    : out std_logic_vector(31 downto 0);

           gpioA_in     : in std_logic_vector(31 downto 0));

   end component; --plasma

   component ddr_ctrl

      port(clk      : in std_logic;

           clk_2x   : in std_logic;

           reset_in : in std_logic;

           address  : in std_logic_vector(25 downto 2);

           byte_we  : in std_logic_vector(3 downto 0);

           data_w   : in std_logic_vector(31 downto 0);

           data_r   : out std_logic_vector(31 downto 0);

           active   : in std_logic;

           no_start : in std_logic;

           no_stop  : in std_logic;

           pause    : out std_logic;

           SD_CK_P  : out std_logic;     --clock_positive

           SD_CK_N  : out std_logic;     --clock_negative

           SD_CKE   : out std_logic;     --clock_enable

           SD_BA    : out std_logic_vector(1 downto 0);  --bank_address

           SD_A     : out std_logic_vector(12 downto 0); --address(row or col)

           SD_CS    : out std_logic;     --chip_select

           SD_RAS   : out std_logic;     --row_address_strobe

           SD_CAS   : out std_logic;     --column_address_strobe

           SD_WE    : out std_logic;     --write_enable

           SD_DQ    : inout std_logic_vector(15 downto 0); --data

           SD_UDM   : out std_logic;     --upper_byte_enable

           SD_UDQS  : inout std_logic;   --upper_data_strobe

           SD_LDM   : out std_logic;     --low_byte_enable

           SD_LDQS  : inout std_logic);  --low_data_strobe

   end component; --ddr

   signal clk_reg      : std_logic;

   signal address      : std_logic_vector(31 downto 2);

   signal data_write   : std_logic_vector(31 downto 0);

   signal data_read    : std_logic_vector(31 downto 0);

   signal data_r_ddr   : std_logic_vector(31 downto 0);

   signal byte_we      : std_logic_vector(3 downto 0);

   signal write_enable : std_logic;

   signal pause_ddr    : std_logic;

   signal pause        : std_logic;

   signal no_ddr_start : std_logic;

   signal no_ddr_stop  : std_logic;

   signal ddr_active   : std_logic;

   signal flash_active : std_logic;

   signal flash_cnt    : std_logic_vector(1 downto 0);

   signal flash_we     : std_logic;

   signal reset        : std_logic;

   signal gpio0_out    : std_logic_vector(31 downto 0);

   signal gpio0_in     : std_logic_vector(31 downto 0);

begin  --architecture

   --Divide 50 MHz clock by two

   clk_div: process(reset, CLK_50MHZ, clk_reg)

   begin

      if reset = '1' then

         clk_reg <= '0';

      elsif rising_edge(CLK_50MHZ) then

         clk_reg <= not clk_reg;

      end if;

   end process; --clk_div

   reset <= ROT_CENTER;

   E_TX_EN   <= gpio0_out(28);  --Ethernet

   E_TXD     <= gpio0_out(27 downto 24);

   E_MDC     <= gpio0_out(23);

   E_MDIO    <= gpio0_out(21) when gpio0_out(22) = '1' else 'Z';

   VGA_VSYNC <= gpio0_out(20);

   VGA_HSYNC <= gpio0_out(19);

   VGA_RED   <= gpio0_out(18);

   VGA_GREEN <= gpio0_out(17);

   VGA_BLUE  <= gpio0_out(16);

   LED <= gpio0_out(7 downto 0);

   gpio0_in(31 downto 21) <= (others => '0');

   gpio0_in(20 downto 13) <= E_RX_CLK & E_RX_DV & E_RXD & E_TX_CLK & E_MDIO;

   gpio0_in(12 downto 10) <= SF_STS & PS2_CLK & PS2_DATA;

   gpio0_in(9 downto 0) <= ROT_A & ROT_B & BTN_EAST & BTN_NORTH &

                           BTN_SOUTH & BTN_WEST & SW;

   ddr_active <= '1' when address(31 downto 28) = "0001" else '0';

   flash_active <= '1' when address(31 downto 28) = "0011" else '0';

   write_enable <= '1' when byte_we /= "0000" else '0';

   u1_plama: plasma

      generic map (memory_type => "XILINX_16X",

                   log_file    => "UNUSED",

                   ethernet    => '1',

                   use_cache   => '1')

      --generic map (memory_type => "DUAL_PORT_",

      --             log_file    => "output2.txt",

      --             ethernet    => '1')

      PORT MAP (

         clk          => clk_reg,

         reset        => reset,

         uart_write   => RS232_DCE_TXD,

         uart_read    => RS232_DCE_RXD,

         address      => address,

         byte_we      => byte_we,

         data_write   => data_write,

         data_read    => data_read,

         mem_pause_in => pause,

         no_ddr_start => no_ddr_start,

         no_ddr_stop  => no_ddr_stop,

         gpio0_out    => gpio0_out,

         gpioA_in     => gpio0_in);

   u2_ddr: ddr_ctrl

      port map (

         clk      => clk_reg,

         clk_2x   => CLK_50MHZ,

         reset_in => reset,

         address  => address(25 downto 2),

         byte_we  => byte_we,

         data_w   => data_write,

         data_r   => data_r_ddr,

         active   => ddr_active,

         no_start => no_ddr_start,

         no_stop  => no_ddr_stop,

         pause    => pause_ddr,

         SD_CK_P  => SD_CK_P,    --clock_positive

         SD_CK_N  => SD_CK_N,    --clock_negative

         SD_CKE   => SD_CKE,     --clock_enable

         SD_BA    => SD_BA,      --bank_address

         SD_A     => SD_A,       --address(row or col)

         SD_CS    => SD_CS,      --chip_select

         SD_RAS   => SD_RAS,     --row_address_strobe

         SD_CAS   => SD_CAS,     --column_address_strobe

         SD_WE    => SD_WE,      --write_enable

         SD_DQ    => SD_DQ,      --data

         SD_UDM   => SD_UDM,     --upper_byte_enable

         SD_UDQS  => SD_UDQS,    --upper_data_strobe

         SD_LDM   => SD_LDM,     --low_byte_enable

         SD_LDQS  => SD_LDQS);   --low_data_strobe

   --Flash control (only lower 16-bit data lines connected)

   flash_ctrl: process(reset, clk_reg, flash_active, write_enable,

                       flash_cnt, pause_ddr)

   begin

      if reset = '1' then

         flash_cnt <= "00";

         flash_we <= '1';

      elsif rising_edge(clk_reg) then

         if flash_active = '0' then

            flash_cnt <= "00";

            flash_we <= '1';

         else

            if write_enable = '1' and flash_cnt(1) = '0' then

               flash_we <= '0';

            else

               flash_we <= '1';

            end if;

            if flash_cnt /= "11" then

               flash_cnt <= flash_cnt + 1;

            end if;

         end if;

      end if;  --rising_edge(clk_reg)

      if pause_ddr = '1' or (flash_active = '1' and flash_cnt /= "11") then

         pause <= '1';

      else

         pause <= '0';

      end if;

   end process; --flash_ctrl

   SF_CE0  <= not flash_active;

   SF_OE   <= write_enable or not flash_active;

   SF_WE   <= flash_we;

   SF_BYTE <= '1';  --16-bit access

   SF_A    <= address(25 downto 2) & '0' when flash_active = '1' else

              "0000000000000000000000000";

   SF_D    <= data_write(15 downto 1) when

              flash_active = '1' and write_enable = '1'

              else "ZZZZZZZZZZZZZZZ";

   SPI_MISO <= data_write(0) when

              flash_active = '1' and write_enable = '1'

              else 'Z';

   data_read(31 downto 16) <= data_r_ddr(31 downto 16);

   data_read(15 downto 0) <= data_r_ddr(15 downto 0) when flash_active = '0'

                             else SF_D & SPI_MISO;

end; --architecture logic