URL https://opencores.org/ocsvn/test_project/test_project/trunk
Subversion Repositories test_project

[/] [test_project/] [trunk/] [linux_sd_driver/] [drivers/] [net/] [irda/] [sa1100_ir.c] - Blame information for rev 62

Details | Compare with Previous | View Log

/*
 *  linux/drivers/net/irda/sa1100_ir.c
 *
 *  Copyright (C) 2000-2001 Russell King
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 *  Infra-red driver for the StrongARM SA1100 embedded microprocessor
 *
 *  Note that we don't have to worry about the SA1111's DMA bugs in here,
 *  so we use the straight forward dma_map_* functions with a null pointer.
 *
 *  This driver takes one kernel command line parameter, sa1100ir=, with
 *  the following options:
 *      max_rate:baudrate       - set the maximum baud rate
 *      power_leve:level        - set the transmitter power level
 *      tx_lpm:0|1              - set transmit low power mode
 */
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/netdevice.h>
#include <linux/slab.h>
#include <linux/rtnetlink.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
 
#include <net/irda/irda.h>
#include <net/irda/wrapper.h>
#include <net/irda/irda_device.h>
 
#include <asm/irq.h>
#include <asm/dma.h>
#include <asm/hardware.h>
#include <asm/mach/irda.h>
 
static int power_level = 3;
static int tx_lpm;
static int max_rate = 4000000;
 
struct sa1100_irda {
        unsigned char           hscr0;
        unsigned char           utcr4;
        unsigned char           power;
        unsigned char           open;
 
        int                     speed;
        int                     newspeed;
 
        struct sk_buff          *txskb;
        struct sk_buff          *rxskb;
        dma_addr_t              txbuf_dma;
        dma_addr_t              rxbuf_dma;
        dma_regs_t              *txdma;
        dma_regs_t              *rxdma;
 
        struct net_device_stats stats;
        struct device           *dev;
        struct irda_platform_data *pdata;
        struct irlap_cb         *irlap;
        struct qos_info         qos;
 
        iobuff_t                tx_buff;
        iobuff_t                rx_buff;
};
 
#define IS_FIR(si)              ((si)->speed >= 4000000)
 
#define HPSIR_MAX_RXLEN         2047
 
/*
 * Allocate and map the receive buffer, unless it is already allocated.
 */
static int sa1100_irda_rx_alloc(struct sa1100_irda *si)
{
        if (si->rxskb)
                return 0;
 
        si->rxskb = alloc_skb(HPSIR_MAX_RXLEN + 1, GFP_ATOMIC);
 
        if (!si->rxskb) {
                printk(KERN_ERR "sa1100_ir: out of memory for RX SKB\n");
                return -ENOMEM;
        }
 
        /*
         * Align any IP headers that may be contained
         * within the frame.
         */
        skb_reserve(si->rxskb, 1);
 
        si->rxbuf_dma = dma_map_single(si->dev, si->rxskb->data,
                                        HPSIR_MAX_RXLEN,
                                        DMA_FROM_DEVICE);
        return 0;
}
 
/*
 * We want to get here as soon as possible, and get the receiver setup.
 * We use the existing buffer.
 */
static void sa1100_irda_rx_dma_start(struct sa1100_irda *si)
{
        if (!si->rxskb) {
                printk(KERN_ERR "sa1100_ir: rx buffer went missing\n");
                return;
        }
 
        /*
         * First empty receive FIFO
         */
        Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
 
        /*
         * Enable the DMA, receiver and receive interrupt.
         */
        sa1100_clear_dma(si->rxdma);
        sa1100_start_dma(si->rxdma, si->rxbuf_dma, HPSIR_MAX_RXLEN);
        Ser2HSCR0 = si->hscr0 | HSCR0_HSSP | HSCR0_RXE;
}
 
/*
 * Set the IrDA communications speed.
 */
static int sa1100_irda_set_speed(struct sa1100_irda *si, int speed)
{
        unsigned long flags;
        int brd, ret = -EINVAL;
 
        switch (speed) {
        case 9600:      case 19200:     case 38400:
        case 57600:     case 115200:
                brd = 3686400 / (16 * speed) - 1;
 
                /*
                 * Stop the receive DMA.
                 */
                if (IS_FIR(si))
                        sa1100_stop_dma(si->rxdma);
 
                local_irq_save(flags);
 
                Ser2UTCR3 = 0;
                Ser2HSCR0 = HSCR0_UART;
 
                Ser2UTCR1 = brd >> 8;
                Ser2UTCR2 = brd;
 
                /*
                 * Clear status register
                 */
                Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
                Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE;
 
                if (si->pdata->set_speed)
                        si->pdata->set_speed(si->dev, speed);
 
                si->speed = speed;
 
                local_irq_restore(flags);
                ret = 0;
                break;
 
        case 4000000:
                local_irq_save(flags);
 
                si->hscr0 = 0;
 
                Ser2HSSR0 = 0xff;
                Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
                Ser2UTCR3 = 0;
 
                si->speed = speed;
 
                if (si->pdata->set_speed)
                        si->pdata->set_speed(si->dev, speed);
 
                sa1100_irda_rx_alloc(si);
                sa1100_irda_rx_dma_start(si);
 
                local_irq_restore(flags);
 
                break;
 
        default:
                break;
        }
 
        return ret;
}
 
/*
 * Control the power state of the IrDA transmitter.
 * State:
 *  0 - off
 *  1 - short range, lowest power
 *  2 - medium range, medium power
 *  3 - maximum range, high power
 *
 * Currently, only assabet is known to support this.
 */
static int
__sa1100_irda_set_power(struct sa1100_irda *si, unsigned int state)
{
        int ret = 0;
        if (si->pdata->set_power)
                ret = si->pdata->set_power(si->dev, state);
        return ret;
}
 
static inline int
sa1100_set_power(struct sa1100_irda *si, unsigned int state)
{
        int ret;
 
        ret = __sa1100_irda_set_power(si, state);
        if (ret == 0)
                si->power = state;
 
        return ret;
}
 
static int sa1100_irda_startup(struct sa1100_irda *si)
{
        int ret;
 
        /*
         * Ensure that the ports for this device are setup correctly.
         */
        if (si->pdata->startup)
                si->pdata->startup(si->dev);
 
        /*
         * Configure PPC for IRDA - we want to drive TXD2 low.
         * We also want to drive this pin low during sleep.
         */
        PPSR &= ~PPC_TXD2;
        PSDR &= ~PPC_TXD2;
        PPDR |= PPC_TXD2;
 
        /*
         * Enable HP-SIR modulation, and ensure that the port is disabled.
         */
        Ser2UTCR3 = 0;
        Ser2HSCR0 = HSCR0_UART;
        Ser2UTCR4 = si->utcr4;
        Ser2UTCR0 = UTCR0_8BitData;
        Ser2HSCR2 = HSCR2_TrDataH | HSCR2_RcDataL;
 
        /*
         * Clear status register
         */
        Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
 
        ret = sa1100_irda_set_speed(si, si->speed = 9600);
        if (ret) {
                Ser2UTCR3 = 0;
                Ser2HSCR0 = 0;
 
                if (si->pdata->shutdown)
                        si->pdata->shutdown(si->dev);
        }
 
        return ret;
}
 
static void sa1100_irda_shutdown(struct sa1100_irda *si)
{
        /*
         * Stop all DMA activity.
         */
        sa1100_stop_dma(si->rxdma);
        sa1100_stop_dma(si->txdma);
 
        /* Disable the port. */
        Ser2UTCR3 = 0;
        Ser2HSCR0 = 0;
 
        if (si->pdata->shutdown)
                si->pdata->shutdown(si->dev);
}
 
#ifdef CONFIG_PM
/*
 * Suspend the IrDA interface.
 */
static int sa1100_irda_suspend(struct platform_device *pdev, pm_message_t state)
{
        struct net_device *dev = platform_get_drvdata(pdev);
        struct sa1100_irda *si;
 
        if (!dev)
                return 0;
 
        si = dev->priv;
        if (si->open) {
                /*
                 * Stop the transmit queue
                 */
                netif_device_detach(dev);
                disable_irq(dev->irq);
                sa1100_irda_shutdown(si);
                __sa1100_irda_set_power(si, 0);
        }
 
        return 0;
}
 
/*
 * Resume the IrDA interface.
 */
static int sa1100_irda_resume(struct platform_device *pdev)
{
        struct net_device *dev = platform_get_drvdata(pdev);
        struct sa1100_irda *si;
 
        if (!dev)
                return 0;
 
        si = dev->priv;
        if (si->open) {
                /*
                 * If we missed a speed change, initialise at the new speed
                 * directly.  It is debatable whether this is actually
                 * required, but in the interests of continuing from where
                 * we left off it is desireable.  The converse argument is
                 * that we should re-negotiate at 9600 baud again.
                 */
                if (si->newspeed) {
                        si->speed = si->newspeed;
                        si->newspeed = 0;
                }
 
                sa1100_irda_startup(si);
                __sa1100_irda_set_power(si, si->power);
                enable_irq(dev->irq);
 
                /*
                 * This automatically wakes up the queue
                 */
                netif_device_attach(dev);
        }
 
        return 0;
}
#else
#define sa1100_irda_suspend     NULL
#define sa1100_irda_resume      NULL
#endif
 
/*
 * HP-SIR format interrupt service routines.
 */
static void sa1100_irda_hpsir_irq(struct net_device *dev)
{
        struct sa1100_irda *si = dev->priv;
        int status;
 
        status = Ser2UTSR0;
 
        /*
         * Deal with any receive errors first.  The bytes in error may be
         * the only bytes in the receive FIFO, so we do this first.
         */
        while (status & UTSR0_EIF) {
                int stat, data;
 
                stat = Ser2UTSR1;
                data = Ser2UTDR;
 
                if (stat & (UTSR1_FRE | UTSR1_ROR)) {
                        si->stats.rx_errors++;
                        if (stat & UTSR1_FRE)
                                si->stats.rx_frame_errors++;
                        if (stat & UTSR1_ROR)
                                si->stats.rx_fifo_errors++;
                } else
                        async_unwrap_char(dev, &si->stats, &si->rx_buff, data);
 
                status = Ser2UTSR0;
        }
 
        /*
         * We must clear certain bits.
         */
        Ser2UTSR0 = status & (UTSR0_RID | UTSR0_RBB | UTSR0_REB);
 
        if (status & UTSR0_RFS) {
                /*
                 * There are at least 4 bytes in the FIFO.  Read 3 bytes
                 * and leave the rest to the block below.
                 */
                async_unwrap_char(dev, &si->stats, &si->rx_buff, Ser2UTDR);
                async_unwrap_char(dev, &si->stats, &si->rx_buff, Ser2UTDR);
                async_unwrap_char(dev, &si->stats, &si->rx_buff, Ser2UTDR);
        }
 
        if (status & (UTSR0_RFS | UTSR0_RID)) {
                /*
                 * Fifo contains more than 1 character.
                 */
                do {
                        async_unwrap_char(dev, &si->stats, &si->rx_buff,
                                          Ser2UTDR);
                } while (Ser2UTSR1 & UTSR1_RNE);
 
                dev->last_rx = jiffies;
        }
 
        if (status & UTSR0_TFS && si->tx_buff.len) {
                /*
                 * Transmitter FIFO is not full
                 */
                do {
                        Ser2UTDR = *si->tx_buff.data++;
                        si->tx_buff.len -= 1;
                } while (Ser2UTSR1 & UTSR1_TNF && si->tx_buff.len);
 
                if (si->tx_buff.len == 0) {
                        si->stats.tx_packets++;
                        si->stats.tx_bytes += si->tx_buff.data -
                                              si->tx_buff.head;
 
                        /*
                         * We need to ensure that the transmitter has
                         * finished.
                         */
                        do
                                rmb();
                        while (Ser2UTSR1 & UTSR1_TBY);
 
                        /*
                         * Ok, we've finished transmitting.  Now enable
                         * the receiver.  Sometimes we get a receive IRQ
                         * immediately after a transmit...
                         */
                        Ser2UTSR0 = UTSR0_REB | UTSR0_RBB | UTSR0_RID;
                        Ser2UTCR3 = UTCR3_RIE | UTCR3_RXE | UTCR3_TXE;
 
                        if (si->newspeed) {
                                sa1100_irda_set_speed(si, si->newspeed);
                                si->newspeed = 0;
                        }
 
                        /* I'm hungry! */
                        netif_wake_queue(dev);
                }
        }
}
 
static void sa1100_irda_fir_error(struct sa1100_irda *si, struct net_device *dev)
{
        struct sk_buff *skb = si->rxskb;
        dma_addr_t dma_addr;
        unsigned int len, stat, data;
 
        if (!skb) {
                printk(KERN_ERR "sa1100_ir: SKB is NULL!\n");
                return;
        }
 
        /*
         * Get the current data position.
         */
        dma_addr = sa1100_get_dma_pos(si->rxdma);
        len = dma_addr - si->rxbuf_dma;
        if (len > HPSIR_MAX_RXLEN)
                len = HPSIR_MAX_RXLEN;
        dma_unmap_single(si->dev, si->rxbuf_dma, len, DMA_FROM_DEVICE);
 
        do {
                /*
                 * Read Status, and then Data.
                 */
                stat = Ser2HSSR1;
                rmb();
                data = Ser2HSDR;
 
                if (stat & (HSSR1_CRE | HSSR1_ROR)) {
                        si->stats.rx_errors++;
                        if (stat & HSSR1_CRE)
                                si->stats.rx_crc_errors++;
                        if (stat & HSSR1_ROR)
                                si->stats.rx_frame_errors++;
                } else
                        skb->data[len++] = data;
 
                /*
                 * If we hit the end of frame, there's
                 * no point in continuing.
                 */
                if (stat & HSSR1_EOF)
                        break;
        } while (Ser2HSSR0 & HSSR0_EIF);
 
        if (stat & HSSR1_EOF) {
                si->rxskb = NULL;
 
                skb_put(skb, len);
                skb->dev = dev;
                skb_reset_mac_header(skb);
                skb->protocol = htons(ETH_P_IRDA);
                si->stats.rx_packets++;
                si->stats.rx_bytes += len;
 
                /*
                 * Before we pass the buffer up, allocate a new one.
                 */
                sa1100_irda_rx_alloc(si);
 
                netif_rx(skb);
                dev->last_rx = jiffies;
        } else {
                /*
                 * Remap the buffer.
                 */
                si->rxbuf_dma = dma_map_single(si->dev, si->rxskb->data,
                                                HPSIR_MAX_RXLEN,
                                                DMA_FROM_DEVICE);
        }
}
 
/*
 * FIR format interrupt service routine.  We only have to
 * handle RX events; transmit events go via the TX DMA handler.
 *
 * No matter what, we disable RX, process, and the restart RX.
 */
static void sa1100_irda_fir_irq(struct net_device *dev)
{
        struct sa1100_irda *si = dev->priv;
 
        /*
         * Stop RX DMA
         */
        sa1100_stop_dma(si->rxdma);
 
        /*
         * Framing error - we throw away the packet completely.
         * Clearing RXE flushes the error conditions and data
         * from the fifo.
         */
        if (Ser2HSSR0 & (HSSR0_FRE | HSSR0_RAB)) {
                si->stats.rx_errors++;
 
                if (Ser2HSSR0 & HSSR0_FRE)
                        si->stats.rx_frame_errors++;
 
                /*
                 * Clear out the DMA...
                 */
                Ser2HSCR0 = si->hscr0 | HSCR0_HSSP;
 
                /*
                 * Clear selected status bits now, so we
                 * don't miss them next time around.
                 */
                Ser2HSSR0 = HSSR0_FRE | HSSR0_RAB;
        }
 
        /*
         * Deal with any receive errors.  The any of the lowest
         * 8 bytes in the FIFO may contain an error.  We must read
         * them one by one.  The "error" could even be the end of
         * packet!
         */
        if (Ser2HSSR0 & HSSR0_EIF)
                sa1100_irda_fir_error(si, dev);
 
        /*
         * No matter what happens, we must restart reception.
         */
        sa1100_irda_rx_dma_start(si);
}
 
static irqreturn_t sa1100_irda_irq(int irq, void *dev_id)
{
        struct net_device *dev = dev_id;
        if (IS_FIR(((struct sa1100_irda *)dev->priv)))
                sa1100_irda_fir_irq(dev);
        else
                sa1100_irda_hpsir_irq(dev);
        return IRQ_HANDLED;
}
 
/*
 * TX DMA completion handler.
 */
static void sa1100_irda_txdma_irq(void *id)
{
        struct net_device *dev = id;
        struct sa1100_irda *si = dev->priv;
        struct sk_buff *skb = si->txskb;
 
        si->txskb = NULL;
 
        /*
         * Wait for the transmission to complete.  Unfortunately,
         * the hardware doesn't give us an interrupt to indicate
         * "end of frame".
         */
        do
                rmb();
        while (!(Ser2HSSR0 & HSSR0_TUR) || Ser2HSSR1 & HSSR1_TBY);
 
        /*
         * Clear the transmit underrun bit.
         */
        Ser2HSSR0 = HSSR0_TUR;
 
        /*
         * Do we need to change speed?  Note that we're lazy
         * here - we don't free the old rxskb.  We don't need
         * to allocate a buffer either.
         */
        if (si->newspeed) {
                sa1100_irda_set_speed(si, si->newspeed);
                si->newspeed = 0;
        }
 
        /*
         * Start reception.  This disables the transmitter for
         * us.  This will be using the existing RX buffer.
         */
        sa1100_irda_rx_dma_start(si);
 
        /*
         * Account and free the packet.
         */
        if (skb) {
                dma_unmap_single(si->dev, si->txbuf_dma, skb->len, DMA_TO_DEVICE);
                si->stats.tx_packets ++;
                si->stats.tx_bytes += skb->len;
                dev_kfree_skb_irq(skb);
        }
 
        /*
         * Make sure that the TX queue is available for sending
         * (for retries).  TX has priority over RX at all times.
         */
        netif_wake_queue(dev);
}
 
static int sa1100_irda_hard_xmit(struct sk_buff *skb, struct net_device *dev)
{
        struct sa1100_irda *si = dev->priv;
        int speed = irda_get_next_speed(skb);
 
        /*
         * Does this packet contain a request to change the interface
         * speed?  If so, remember it until we complete the transmission
         * of this frame.
         */
        if (speed != si->speed && speed != -1)
                si->newspeed = speed;
 
        /*
         * If this is an empty frame, we can bypass a lot.
         */
        if (skb->len == 0) {
                if (si->newspeed) {
                        si->newspeed = 0;
                        sa1100_irda_set_speed(si, speed);
                }
                dev_kfree_skb(skb);
                return 0;
        }
 
        if (!IS_FIR(si)) {
                netif_stop_queue(dev);
 
                si->tx_buff.data = si->tx_buff.head;
                si->tx_buff.len  = async_wrap_skb(skb, si->tx_buff.data,
                                                  si->tx_buff.truesize);
 
                /*
                 * Set the transmit interrupt enable.  This will fire
                 * off an interrupt immediately.  Note that we disable
                 * the receiver so we won't get spurious characteres
                 * received.
                 */
                Ser2UTCR3 = UTCR3_TIE | UTCR3_TXE;
 
                dev_kfree_skb(skb);
        } else {
                int mtt = irda_get_mtt(skb);
 
                /*
                 * We must not be transmitting...
                 */
                BUG_ON(si->txskb);
 
                netif_stop_queue(dev);
 
                si->txskb = skb;
                si->txbuf_dma = dma_map_single(si->dev, skb->data,
                                         skb->len, DMA_TO_DEVICE);
 
                sa1100_start_dma(si->txdma, si->txbuf_dma, skb->len);
 
                /*
                 * If we have a mean turn-around time, impose the specified
                 * specified delay.  We could shorten this by timing from
                 * the point we received the packet.
                 */
                if (mtt)
                        udelay(mtt);
 
                Ser2HSCR0 = si->hscr0 | HSCR0_HSSP | HSCR0_TXE;
        }
 
        dev->trans_start = jiffies;
 
        return 0;
}
 
static int
sa1100_irda_ioctl(struct net_device *dev, struct ifreq *ifreq, int cmd)
{
        struct if_irda_req *rq = (struct if_irda_req *)ifreq;
        struct sa1100_irda *si = dev->priv;
        int ret = -EOPNOTSUPP;
 
        switch (cmd) {
        case SIOCSBANDWIDTH:
                if (capable(CAP_NET_ADMIN)) {
                        /*
                         * We are unable to set the speed if the
                         * device is not running.
                         */
                        if (si->open) {
                                ret = sa1100_irda_set_speed(si,
                                                rq->ifr_baudrate);
                        } else {
                                printk("sa1100_irda_ioctl: SIOCSBANDWIDTH: !netif_running\n");
                                ret = 0;
                        }
                }
                break;
 
        case SIOCSMEDIABUSY:
                ret = -EPERM;
                if (capable(CAP_NET_ADMIN)) {
                        irda_device_set_media_busy(dev, TRUE);
                        ret = 0;
                }
                break;
 
        case SIOCGRECEIVING:
                rq->ifr_receiving = IS_FIR(si) ? 0
                                        : si->rx_buff.state != OUTSIDE_FRAME;
                break;
 
        default:
                break;
        }
 
        return ret;
}
 
static struct net_device_stats *sa1100_irda_stats(struct net_device *dev)
{
        struct sa1100_irda *si = dev->priv;
        return &si->stats;
}
 
static int sa1100_irda_start(struct net_device *dev)
{
        struct sa1100_irda *si = dev->priv;
        int err;
 
        si->speed = 9600;
 
        err = request_irq(dev->irq, sa1100_irda_irq, 0, dev->name, dev);
        if (err)
                goto err_irq;
 
        err = sa1100_request_dma(DMA_Ser2HSSPRd, "IrDA receive",
                                 NULL, NULL, &si->rxdma);
        if (err)
                goto err_rx_dma;
 
        err = sa1100_request_dma(DMA_Ser2HSSPWr, "IrDA transmit",
                                 sa1100_irda_txdma_irq, dev, &si->txdma);
        if (err)
                goto err_tx_dma;
 
        /*
         * The interrupt must remain disabled for now.
         */
        disable_irq(dev->irq);
 
        /*
         * Setup the serial port for the specified speed.
         */
        err = sa1100_irda_startup(si);
        if (err)
                goto err_startup;
 
        /*
         * Open a new IrLAP layer instance.
         */
        si->irlap = irlap_open(dev, &si->qos, "sa1100");
        err = -ENOMEM;
        if (!si->irlap)
                goto err_irlap;
 
        /*
         * Now enable the interrupt and start the queue
         */
        si->open = 1;
        sa1100_set_power(si, power_level); /* low power mode */
        enable_irq(dev->irq);
        netif_start_queue(dev);
        return 0;
 
err_irlap:
        si->open = 0;
        sa1100_irda_shutdown(si);
err_startup:
        sa1100_free_dma(si->txdma);
err_tx_dma:
        sa1100_free_dma(si->rxdma);
err_rx_dma:
        free_irq(dev->irq, dev);
err_irq:
        return err;
}
 
static int sa1100_irda_stop(struct net_device *dev)
{
        struct sa1100_irda *si = dev->priv;
 
        disable_irq(dev->irq);
        sa1100_irda_shutdown(si);
 
        /*
         * If we have been doing DMA receive, make sure we
         * tidy that up cleanly.
         */
        if (si->rxskb) {
                dma_unmap_single(si->dev, si->rxbuf_dma, HPSIR_MAX_RXLEN,
                                 DMA_FROM_DEVICE);
                dev_kfree_skb(si->rxskb);
                si->rxskb = NULL;
        }
 
        /* Stop IrLAP */
        if (si->irlap) {
                irlap_close(si->irlap);
                si->irlap = NULL;
        }
 
        netif_stop_queue(dev);
        si->open = 0;
 
        /*
         * Free resources
         */
        sa1100_free_dma(si->txdma);
        sa1100_free_dma(si->rxdma);
        free_irq(dev->irq, dev);
 
        sa1100_set_power(si, 0);
 
        return 0;
}
 
static int sa1100_irda_init_iobuf(iobuff_t *io, int size)
{
        io->head = kmalloc(size, GFP_KERNEL | GFP_DMA);
        if (io->head != NULL) {
                io->truesize = size;
                io->in_frame = FALSE;
                io->state    = OUTSIDE_FRAME;
                io->data     = io->head;
        }
        return io->head ? 0 : -ENOMEM;
}
 
static int sa1100_irda_probe(struct platform_device *pdev)
{
        struct net_device *dev;
        struct sa1100_irda *si;
        unsigned int baudrate_mask;
        int err;
 
        if (!pdev->dev.platform_data)
                return -EINVAL;
 
        err = request_mem_region(__PREG(Ser2UTCR0), 0x24, "IrDA") ? 0 : -EBUSY;
        if (err)
                goto err_mem_1;
        err = request_mem_region(__PREG(Ser2HSCR0), 0x1c, "IrDA") ? 0 : -EBUSY;
        if (err)
                goto err_mem_2;
        err = request_mem_region(__PREG(Ser2HSCR2), 0x04, "IrDA") ? 0 : -EBUSY;
        if (err)
                goto err_mem_3;
 
        dev = alloc_irdadev(sizeof(struct sa1100_irda));
        if (!dev)
                goto err_mem_4;
 
        si = dev->priv;
        si->dev = &pdev->dev;
        si->pdata = pdev->dev.platform_data;
 
        /*
         * Initialise the HP-SIR buffers
         */
        err = sa1100_irda_init_iobuf(&si->rx_buff, 14384);
        if (err)
                goto err_mem_5;
        err = sa1100_irda_init_iobuf(&si->tx_buff, 4000);
        if (err)
                goto err_mem_5;
 
        dev->hard_start_xmit    = sa1100_irda_hard_xmit;
        dev->open               = sa1100_irda_start;
        dev->stop               = sa1100_irda_stop;
        dev->do_ioctl           = sa1100_irda_ioctl;
        dev->get_stats          = sa1100_irda_stats;
        dev->irq                = IRQ_Ser2ICP;
 
        irda_init_max_qos_capabilies(&si->qos);
 
        /*
         * We support original IRDA up to 115k2. (we don't currently
         * support 4Mbps).  Min Turn Time set to 1ms or greater.
         */
        baudrate_mask = IR_9600;
 
        switch (max_rate) {
        case 4000000:           baudrate_mask |= IR_4000000 << 8;
        case 115200:            baudrate_mask |= IR_115200;
        case 57600:             baudrate_mask |= IR_57600;
        case 38400:             baudrate_mask |= IR_38400;
        case 19200:             baudrate_mask |= IR_19200;
        }
 
        si->qos.baud_rate.bits &= baudrate_mask;
        si->qos.min_turn_time.bits = 7;
 
        irda_qos_bits_to_value(&si->qos);
 
        si->utcr4 = UTCR4_HPSIR;
        if (tx_lpm)
                si->utcr4 |= UTCR4_Z1_6us;
 
        /*
         * Initially enable HP-SIR modulation, and ensure that the port
         * is disabled.
         */
        Ser2UTCR3 = 0;
        Ser2UTCR4 = si->utcr4;
        Ser2HSCR0 = HSCR0_UART;
 
        err = register_netdev(dev);
        if (err == 0)
                platform_set_drvdata(pdev, dev);
 
        if (err) {
 err_mem_5:
                kfree(si->tx_buff.head);
                kfree(si->rx_buff.head);
                free_netdev(dev);
 err_mem_4:
                release_mem_region(__PREG(Ser2HSCR2), 0x04);
 err_mem_3:
                release_mem_region(__PREG(Ser2HSCR0), 0x1c);
 err_mem_2:
                release_mem_region(__PREG(Ser2UTCR0), 0x24);
        }
 err_mem_1:
        return err;
}
 
static int sa1100_irda_remove(struct platform_device *pdev)
{
        struct net_device *dev = platform_get_drvdata(pdev);
 
        if (dev) {
                struct sa1100_irda *si = dev->priv;
                unregister_netdev(dev);
                kfree(si->tx_buff.head);
                kfree(si->rx_buff.head);
                free_netdev(dev);
        }
 
        release_mem_region(__PREG(Ser2HSCR2), 0x04);
        release_mem_region(__PREG(Ser2HSCR0), 0x1c);
        release_mem_region(__PREG(Ser2UTCR0), 0x24);
 
        return 0;
}
 
static struct platform_driver sa1100ir_driver = {
        .probe          = sa1100_irda_probe,
        .remove         = sa1100_irda_remove,
        .suspend        = sa1100_irda_suspend,
        .resume         = sa1100_irda_resume,
        .driver         = {
                .name   = "sa11x0-ir",
        },
};
 
static int __init sa1100_irda_init(void)
{
        /*
         * Limit power level a sensible range.
         */
        if (power_level < 1)
                power_level = 1;
        if (power_level > 3)
                power_level = 3;
 
        return platform_driver_register(&sa1100ir_driver);
}
 
static void __exit sa1100_irda_exit(void)
{
        platform_driver_unregister(&sa1100ir_driver);
}
 
module_init(sa1100_irda_init);
module_exit(sa1100_irda_exit);
module_param(power_level, int, 0);
module_param(tx_lpm, int, 0);
module_param(max_rate, int, 0);
 
MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
MODULE_DESCRIPTION("StrongARM SA1100 IrDA driver");
MODULE_LICENSE("GPL");
MODULE_PARM_DESC(power_level, "IrDA power level, 1 (low) to 3 (high)");
MODULE_PARM_DESC(tx_lpm, "Enable transmitter low power (1.6us) mode");
MODULE_PARM_DESC(max_rate, "Maximum baud rate (4000000, 115200, 57600, 38400, 19200, 9600)");
Browse

Tools

Subversion Repositories test_project

[/] [test_project/] [trunk/] [linux_sd_driver/] [drivers/] [net/] [irda/] [sa1100_ir.c] - Blame information for rev 62

Line No.	Rev	Author	Line
1	62	marcus.erl	`/*`
2			`* linux/drivers/net/irda/sa1100_ir.c`
3			`*`
4			`* Copyright (C) 2000-2001 Russell King`
5			`*`
6			`* This program is free software; you can redistribute it and/or modify`
7			`* it under the terms of the GNU General Public License version 2 as`
8			`* published by the Free Software Foundation.`
9			`*`
10			`* Infra-red driver for the StrongARM SA1100 embedded microprocessor`
11			`*`
12			`* Note that we don't have to worry about the SA1111's DMA bugs in here,`
13			`* so we use the straight forward dma_map_* functions with a null pointer.`
14			`*`
15			`* This driver takes one kernel command line parameter, sa1100ir=, with`
16			`* the following options:`
17			`* max_rate:baudrate - set the maximum baud rate`
18			`* power_leve:level - set the transmitter power level`
19			`* tx_lpm:0\|1 - set transmit low power mode`
20			`*/`
21			`#include <linux/module.h>`
22			`#include <linux/moduleparam.h>`
23			`#include <linux/types.h>`
24			`#include <linux/init.h>`
25			`#include <linux/errno.h>`
26			`#include <linux/netdevice.h>`
27			`#include <linux/slab.h>`
28			`#include <linux/rtnetlink.h>`
29			`#include <linux/interrupt.h>`
30			`#include <linux/delay.h>`
31			`#include <linux/platform_device.h>`
32			`#include <linux/dma-mapping.h>`
33
34			`#include <net/irda/irda.h>`
35			`#include <net/irda/wrapper.h>`
36			`#include <net/irda/irda_device.h>`
37
38			`#include <asm/irq.h>`
39			`#include <asm/dma.h>`
40			`#include <asm/hardware.h>`