OpenCores
URL https://opencores.org/ocsvn/test_project/test_project/trunk

Subversion Repositories test_project

[/] [test_project/] [trunk/] [linux_sd_driver/] [drivers/] [net/] [phy/] [Kconfig] - Blame information for rev 62

Details | Compare with Previous | View Log

Line No. Rev Author Line
1 62 marcus.erl
#
2
# PHY Layer Configuration
3
#
4
 
5
menuconfig PHYLIB
6
        tristate "PHY Device support and infrastructure"
7
        depends on !S390
8
        depends on NET_ETHERNET && (BROKEN || !S390)
9
        help
10
          Ethernet controllers are usually attached to PHY
11
          devices.  This option provides infrastructure for
12
          managing PHY devices.
13
 
14
if PHYLIB
15
 
16
comment "MII PHY device drivers"
17
 
18
config MARVELL_PHY
19
        tristate "Drivers for Marvell PHYs"
20
        ---help---
21
          Currently has a driver for the 88E1011S
22
 
23
config DAVICOM_PHY
24
        tristate "Drivers for Davicom PHYs"
25
        ---help---
26
          Currently supports dm9161e and dm9131
27
 
28
config QSEMI_PHY
29
        tristate "Drivers for Quality Semiconductor PHYs"
30
        ---help---
31
          Currently supports the qs6612
32
 
33
config LXT_PHY
34
        tristate "Drivers for the Intel LXT PHYs"
35
        ---help---
36
          Currently supports the lxt970, lxt971
37
 
38
config CICADA_PHY
39
        tristate "Drivers for the Cicada PHYs"
40
        ---help---
41
          Currently supports the cis8204
42
 
43
config VITESSE_PHY
44
        tristate "Drivers for the Vitesse PHYs"
45
        ---help---
46
          Currently supports the vsc8244
47
 
48
config SMSC_PHY
49
        tristate "Drivers for SMSC PHYs"
50
        ---help---
51
          Currently supports the LAN83C185 PHY
52
 
53
config BROADCOM_PHY
54
        tristate "Drivers for Broadcom PHYs"
55
        ---help---
56
          Currently supports the BCM5411, BCM5421 and BCM5461 PHYs.
57
 
58
config ICPLUS_PHY
59
        tristate "Drivers for ICPlus PHYs"
60
        ---help---
61
          Currently supports the IP175C PHY.
62
 
63
config FIXED_PHY
64
        tristate "Drivers for PHY emulation on fixed speed/link"
65
        ---help---
66
          Adds the driver to PHY layer to cover the boards that do not have any PHY bound,
67
          but with the ability to manipulate the speed/link in software. The relevant MII
68
          speed/duplex parameters could be effectively handled in a user-specified function.
69
          Currently tested with mpc866ads.
70
 
71
config FIXED_MII_10_FDX
72
        bool "Emulation for 10M Fdx fixed PHY behavior"
73
        depends on FIXED_PHY
74
 
75
config FIXED_MII_100_FDX
76
        bool "Emulation for 100M Fdx fixed PHY behavior"
77
        depends on FIXED_PHY
78
 
79
config FIXED_MII_1000_FDX
80
        bool "Emulation for 1000M Fdx fixed PHY behavior"
81
        depends on FIXED_PHY
82
 
83
config FIXED_MII_AMNT
84
        int "Number of emulated PHYs to allocate "
85
        depends on FIXED_PHY
86
        default "1"
87
        ---help---
88
        Sometimes it is required to have several independent emulated
89
        PHYs on the bus (in case of multi-eth but phy-less HW for instance).
90
        This control will have specified number allocated for each fixed
91
        PHY type enabled.
92
 
93
config MDIO_BITBANG
94
        tristate "Support for bitbanged MDIO buses"
95
        help
96
          This module implements the MDIO bus protocol in software,
97
          for use by low level drivers that export the ability to
98
          drive the relevant pins.
99
 
100
          If in doubt, say N.
101
 
102
endif # PHYLIB

powered by: WebSVN 2.1.0

© copyright 1999-2025 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.