URL https://opencores.org/ocsvn/test_project/test_project/trunk

Subversion Repositories test_project

[/] [test_project/] [trunk/] [linux_sd_driver/] [drivers/] [net/] [wireless/] [net2280.h] - Blame information for rev 62

Details | Compare with Previous | View Log


#ifndef NET2280_H
#define NET2280_H
/*
 * NetChip 2280 high/full speed USB device controller.
 * Unlike many such controllers, this one talks PCI.
 */
 
/*
 * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com)
 * Copyright (C) 2003 David Brownell
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */
 
/*-------------------------------------------------------------------------*/
 
/* NET2280 MEMORY MAPPED REGISTERS
 *
 * The register layout came from the chip documentation, and the bit
 * number definitions were extracted from chip specification.
 *
 * Use the shift operator ('<<') to build bit masks, with readl/writel
 * to access the registers through PCI.
 */
 
/* main registers, BAR0 + 0x0000 */
struct net2280_regs {
        // offset 0x0000
        __le32                  devinit;
#define     LOCAL_CLOCK_FREQUENCY                               8
#define     FORCE_PCI_RESET                                     7
#define     PCI_ID                                              6
#define     PCI_ENABLE                                          5
#define     FIFO_SOFT_RESET                                     4
#define     CFG_SOFT_RESET                                      3
#define     PCI_SOFT_RESET                                      2
#define     USB_SOFT_RESET                                      1
#define     M8051_RESET                                         0
        __le32                  eectl;
#define     EEPROM_ADDRESS_WIDTH                                23
#define     EEPROM_CHIP_SELECT_ACTIVE                           22
#define     EEPROM_PRESENT                                      21
#define     EEPROM_VALID                                        20
#define     EEPROM_BUSY                                         19
#define     EEPROM_CHIP_SELECT_ENABLE                           18
#define     EEPROM_BYTE_READ_START                              17
#define     EEPROM_BYTE_WRITE_START                             16
#define     EEPROM_READ_DATA                                    8
#define     EEPROM_WRITE_DATA                                   0
        __le32                  eeclkfreq;
        u32                     _unused0;
        // offset 0x0010
 
        __le32                  pciirqenb0;     /* interrupt PCI master ... */
#define     SETUP_PACKET_INTERRUPT_ENABLE                       7
#define     ENDPOINT_F_INTERRUPT_ENABLE                         6
#define     ENDPOINT_E_INTERRUPT_ENABLE                         5
#define     ENDPOINT_D_INTERRUPT_ENABLE                         4
#define     ENDPOINT_C_INTERRUPT_ENABLE                         3
#define     ENDPOINT_B_INTERRUPT_ENABLE                         2
#define     ENDPOINT_A_INTERRUPT_ENABLE                         1
#define     ENDPOINT_0_INTERRUPT_ENABLE                         0
        __le32                  pciirqenb1;
#define     PCI_INTERRUPT_ENABLE                                31
#define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
#define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
#define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
#define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
#define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
#define     PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE          18
#define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
#define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
#define     GPIO_INTERRUPT_ENABLE                               13
#define     DMA_D_INTERRUPT_ENABLE                              12
#define     DMA_C_INTERRUPT_ENABLE                              11
#define     DMA_B_INTERRUPT_ENABLE                              10
#define     DMA_A_INTERRUPT_ENABLE                              9
#define     EEPROM_DONE_INTERRUPT_ENABLE                        8
#define     VBUS_INTERRUPT_ENABLE                               7
#define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
#define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
#define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
#define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
#define     RESUME_INTERRUPT_ENABLE                             1
#define     SOF_INTERRUPT_ENABLE                                0
        __le32                  cpu_irqenb0;    /* ... or onboard 8051 */
#define     SETUP_PACKET_INTERRUPT_ENABLE                       7
#define     ENDPOINT_F_INTERRUPT_ENABLE                         6
#define     ENDPOINT_E_INTERRUPT_ENABLE                         5
#define     ENDPOINT_D_INTERRUPT_ENABLE                         4
#define     ENDPOINT_C_INTERRUPT_ENABLE                         3
#define     ENDPOINT_B_INTERRUPT_ENABLE                         2
#define     ENDPOINT_A_INTERRUPT_ENABLE                         1
#define     ENDPOINT_0_INTERRUPT_ENABLE                         0
        __le32                  cpu_irqenb1;
#define     CPU_INTERRUPT_ENABLE                                31
#define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
#define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
#define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
#define     PCI_INTA_INTERRUPT_ENABLE                           24
#define     PCI_PME_INTERRUPT_ENABLE                            23
#define     PCI_SERR_INTERRUPT_ENABLE                           22
#define     PCI_PERR_INTERRUPT_ENABLE                           21
#define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
#define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
#define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
#define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
#define     GPIO_INTERRUPT_ENABLE                               13
#define     DMA_D_INTERRUPT_ENABLE                              12
#define     DMA_C_INTERRUPT_ENABLE                              11
#define     DMA_B_INTERRUPT_ENABLE                              10
#define     DMA_A_INTERRUPT_ENABLE                              9
#define     EEPROM_DONE_INTERRUPT_ENABLE                        8
#define     VBUS_INTERRUPT_ENABLE                               7
#define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
#define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
#define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
#define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
#define     RESUME_INTERRUPT_ENABLE                             1
#define     SOF_INTERRUPT_ENABLE                                0
 
        // offset 0x0020
        u32                     _unused1;
        __le32                  usbirqenb1;
#define     USB_INTERRUPT_ENABLE                                31
#define     POWER_STATE_CHANGE_INTERRUPT_ENABLE                 27
#define     PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE                26
#define     PCI_PARITY_ERROR_INTERRUPT_ENABLE                   25
#define     PCI_INTA_INTERRUPT_ENABLE                           24
#define     PCI_PME_INTERRUPT_ENABLE                            23
#define     PCI_SERR_INTERRUPT_ENABLE                           22
#define     PCI_PERR_INTERRUPT_ENABLE                           21
#define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE          20
#define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE          19
#define     PCI_RETRY_ABORT_INTERRUPT_ENABLE                    17
#define     PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE              16
#define     GPIO_INTERRUPT_ENABLE                               13
#define     DMA_D_INTERRUPT_ENABLE                              12
#define     DMA_C_INTERRUPT_ENABLE                              11
#define     DMA_B_INTERRUPT_ENABLE                              10
#define     DMA_A_INTERRUPT_ENABLE                              9
#define     EEPROM_DONE_INTERRUPT_ENABLE                        8
#define     VBUS_INTERRUPT_ENABLE                               7
#define     CONTROL_STATUS_INTERRUPT_ENABLE                     6
#define     ROOT_PORT_RESET_INTERRUPT_ENABLE                    4
#define     SUSPEND_REQUEST_INTERRUPT_ENABLE                    3
#define     SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE             2
#define     RESUME_INTERRUPT_ENABLE                             1
#define     SOF_INTERRUPT_ENABLE                                0
        __le32                  irqstat0;
#define     INTA_ASSERTED                                       12
#define     SETUP_PACKET_INTERRUPT                              7
#define     ENDPOINT_F_INTERRUPT                                6
#define     ENDPOINT_E_INTERRUPT                                5
#define     ENDPOINT_D_INTERRUPT                                4
#define     ENDPOINT_C_INTERRUPT                                3
#define     ENDPOINT_B_INTERRUPT                                2
#define     ENDPOINT_A_INTERRUPT                                1
#define     ENDPOINT_0_INTERRUPT                                0
        __le32                  irqstat1;
#define     POWER_STATE_CHANGE_INTERRUPT                        27
#define     PCI_ARBITER_TIMEOUT_INTERRUPT                       26
#define     PCI_PARITY_ERROR_INTERRUPT                          25
#define     PCI_INTA_INTERRUPT                                  24
#define     PCI_PME_INTERRUPT                                   23
#define     PCI_SERR_INTERRUPT                                  22
#define     PCI_PERR_INTERRUPT                                  21
#define     PCI_MASTER_ABORT_RECEIVED_INTERRUPT                 20
#define     PCI_TARGET_ABORT_RECEIVED_INTERRUPT                 19
#define     PCI_RETRY_ABORT_INTERRUPT                           17
#define     PCI_MASTER_CYCLE_DONE_INTERRUPT                     16
#define     GPIO_INTERRUPT                                      13
#define     DMA_D_INTERRUPT                                     12
#define     DMA_C_INTERRUPT                                     11
#define     DMA_B_INTERRUPT                                     10
#define     DMA_A_INTERRUPT                                     9
#define     EEPROM_DONE_INTERRUPT                               8
#define     VBUS_INTERRUPT                                      7
#define     CONTROL_STATUS_INTERRUPT                            6
#define     ROOT_PORT_RESET_INTERRUPT                           4
#define     SUSPEND_REQUEST_INTERRUPT                           3
#define     SUSPEND_REQUEST_CHANGE_INTERRUPT                    2
#define     RESUME_INTERRUPT                                    1
#define     SOF_INTERRUPT                                       0
        // offset 0x0030
        __le32                  idxaddr;
        __le32                  idxdata;
        __le32                  fifoctl;
#define     PCI_BASE2_RANGE                                     16
#define     IGNORE_FIFO_AVAILABILITY                            3
#define     PCI_BASE2_SELECT                                    2
#define     FIFO_CONFIGURATION_SELECT                           0
        u32                     _unused2;
        // offset 0x0040
        __le32                  memaddr;
#define     START                                               28
#define     DIRECTION                                           27
#define     FIFO_DIAGNOSTIC_SELECT                              24
#define     MEMORY_ADDRESS                                      0
        __le32                  memdata0;
        __le32                  memdata1;
        u32                     _unused3;
        // offset 0x0050
        __le32                  gpioctl;
#define     GPIO3_LED_SELECT                                    12
#define     GPIO3_INTERRUPT_ENABLE                              11
#define     GPIO2_INTERRUPT_ENABLE                              10
#define     GPIO1_INTERRUPT_ENABLE                              9
#define     GPIO0_INTERRUPT_ENABLE                              8
#define     GPIO3_OUTPUT_ENABLE                                 7
#define     GPIO2_OUTPUT_ENABLE                                 6
#define     GPIO1_OUTPUT_ENABLE                                 5
#define     GPIO0_OUTPUT_ENABLE                                 4
#define     GPIO3_DATA                                          3
#define     GPIO2_DATA                                          2
#define     GPIO1_DATA                                          1
#define     GPIO0_DATA                                          0
        __le32                  gpiostat;
#define     GPIO3_INTERRUPT                                     3
#define     GPIO2_INTERRUPT                                     2
#define     GPIO1_INTERRUPT                                     1
#define     GPIO0_INTERRUPT                                     0
} __attribute__ ((packed));
 
/* usb control, BAR0 + 0x0080 */
struct net2280_usb_regs {
        // offset 0x0080
        __le32                  stdrsp;
#define     STALL_UNSUPPORTED_REQUESTS                          31
#define     SET_TEST_MODE                                       16
#define     GET_OTHER_SPEED_CONFIGURATION                       15
#define     GET_DEVICE_QUALIFIER                                14
#define     SET_ADDRESS                                         13
#define     ENDPOINT_SET_CLEAR_HALT                             12
#define     DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP               11
#define     GET_STRING_DESCRIPTOR_2                             10
#define     GET_STRING_DESCRIPTOR_1                             9
#define     GET_STRING_DESCRIPTOR_0                             8
#define     GET_SET_INTERFACE                                   6
#define     GET_SET_CONFIGURATION                               5
#define     GET_CONFIGURATION_DESCRIPTOR                        4
#define     GET_DEVICE_DESCRIPTOR                               3
#define     GET_ENDPOINT_STATUS                                 2
#define     GET_INTERFACE_STATUS                                1
#define     GET_DEVICE_STATUS                                   0
        __le32                  prodvendid;
#define     PRODUCT_ID                                          16
#define     VENDOR_ID                                           0
        __le32                  relnum;
        __le32                  usbctl;
#define     SERIAL_NUMBER_INDEX                                 16
#define     PRODUCT_ID_STRING_ENABLE                            13
#define     VENDOR_ID_STRING_ENABLE                             12
#define     USB_ROOT_PORT_WAKEUP_ENABLE                         11
#define     VBUS_PIN                                            10
#define     TIMED_DISCONNECT                                    9
#define     SUSPEND_IMMEDIATELY                                 7
#define     SELF_POWERED_USB_DEVICE                             6
#define     REMOTE_WAKEUP_SUPPORT                               5
#define     PME_POLARITY                                        4
#define     USB_DETECT_ENABLE                                   3
#define     PME_WAKEUP_ENABLE                                   2
#define     DEVICE_REMOTE_WAKEUP_ENABLE                         1
#define     SELF_POWERED_STATUS                                 0
        // offset 0x0090
        __le32                  usbstat;
#define     HIGH_SPEED                                          7
#define     FULL_SPEED                                          6
#define     GENERATE_RESUME                                     5
#define     GENERATE_DEVICE_REMOTE_WAKEUP                       4
        __le32                  xcvrdiag;
#define     FORCE_HIGH_SPEED_MODE                               31
#define     FORCE_FULL_SPEED_MODE                               30
#define     USB_TEST_MODE                                       24
#define     LINE_STATE                                          16
#define     TRANSCEIVER_OPERATION_MODE                          2
#define     TRANSCEIVER_SELECT                                  1
#define     TERMINATION_SELECT                                  0
        __le32                  setup0123;
        __le32                  setup4567;
        // offset 0x0090
        u32                     _unused0;
        __le32                  ouraddr;
#define     FORCE_IMMEDIATE                                     7
#define     OUR_USB_ADDRESS                                     0
        __le32                  ourconfig;
} __attribute__ ((packed));
 
/* pci control, BAR0 + 0x0100 */
struct net2280_pci_regs {
        // offset 0x0100
        __le32                  pcimstctl;
#define     PCI_ARBITER_PARK_SELECT                             13
#define     PCI_MULTI LEVEL_ARBITER                             12
#define     PCI_RETRY_ABORT_ENABLE                              11
#define     DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE              10
#define     DMA_READ_MULTIPLE_ENABLE                            9
#define     DMA_READ_LINE_ENABLE                                8
#define     PCI_MASTER_COMMAND_SELECT                           6
#define         MEM_READ_OR_WRITE                                   0
#define         IO_READ_OR_WRITE                                    1
#define         CFG_READ_OR_WRITE                                   2
#define     PCI_MASTER_START                                    5
#define     PCI_MASTER_READ_WRITE                               4
#define         PCI_MASTER_WRITE                                    0
#define         PCI_MASTER_READ                                     1
#define     PCI_MASTER_BYTE_WRITE_ENABLES                       0
        __le32                  pcimstaddr;
        __le32                  pcimstdata;
        __le32                  pcimststat;
#define     PCI_ARBITER_CLEAR                                   2
#define     PCI_EXTERNAL_ARBITER                                1
#define     PCI_HOST_MODE                                       0
} __attribute__ ((packed));
 
/* dma control, BAR0 + 0x0180 ... array of four structs like this,
 * for channels 0..3.  see also struct net2280_dma:  descriptor
 * that can be loaded into some of these registers.
 */
struct net2280_dma_regs {       /* [11.7] */
        // offset 0x0180, 0x01a0, 0x01c0, 0x01e0,
        __le32                  dmactl;
#define     DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE            25
#define     DMA_CLEAR_COUNT_ENABLE                              21
#define     DESCRIPTOR_POLLING_RATE                             19
#define         POLL_CONTINUOUS                                     0
#define         POLL_1_USEC                                         1
#define         POLL_100_USEC                                       2
#define         POLL_1_MSEC                                         3
#define     DMA_VALID_BIT_POLLING_ENABLE                        18
#define     DMA_VALID_BIT_ENABLE                                17
#define     DMA_SCATTER_GATHER_ENABLE                           16
#define     DMA_OUT_AUTO_START_ENABLE                           4
#define     DMA_PREEMPT_ENABLE                                  3
#define     DMA_FIFO_VALIDATE                                   2
#define     DMA_ENABLE                                          1
#define     DMA_ADDRESS_HOLD                                    0
        __le32                  dmastat;
#define     DMA_SCATTER_GATHER_DONE_INTERRUPT                   25
#define     DMA_TRANSACTION_DONE_INTERRUPT                      24
#define     DMA_ABORT                                           1
#define     DMA_START                                           0
        u32                     _unused0[2];
        // offset 0x0190, 0x01b0, 0x01d0, 0x01f0,
        __le32                  dmacount;
#define     VALID_BIT                                           31
#define     DMA_DIRECTION                                       30
#define     DMA_DONE_INTERRUPT_ENABLE                           29
#define     END_OF_CHAIN                                        28
#define         DMA_BYTE_COUNT_MASK                                 ((1<<24)-1)
#define     DMA_BYTE_COUNT                                      0
        __le32                  dmaaddr;
        __le32                  dmadesc;
        u32                     _unused1;
} __attribute__ ((packed));
 
/* dedicated endpoint registers, BAR0 + 0x0200 */
 
struct net2280_dep_regs {       /* [11.8] */
        // offset 0x0200, 0x0210, 0x220, 0x230, 0x240
        __le32                  dep_cfg;
        // offset 0x0204, 0x0214, 0x224, 0x234, 0x244
        __le32                  dep_rsp;
        u32                     _unused[2];
} __attribute__ ((packed));
 
/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs
 * like this, for ep0 then the configurable endpoints A..F
 * ep0 reserved for control; E and F have only 64 bytes of fifo
 */
struct net2280_ep_regs {        /* [11.9] */
        // offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0
        __le32                  ep_cfg;
#define     ENDPOINT_BYTE_COUNT                                 16
#define     ENDPOINT_ENABLE                                     10
#define     ENDPOINT_TYPE                                       8
#define     ENDPOINT_DIRECTION                                  7
#define     ENDPOINT_NUMBER                                     0
        __le32                  ep_rsp;
#define     SET_NAK_OUT_PACKETS                                 15
#define     SET_EP_HIDE_STATUS_PHASE                            14
#define     SET_EP_FORCE_CRC_ERROR                              13
#define     SET_INTERRUPT_MODE                                  12
#define     SET_CONTROL_STATUS_PHASE_HANDSHAKE                  11
#define     SET_NAK_OUT_PACKETS_MODE                            10
#define     SET_ENDPOINT_TOGGLE                                 9
#define     SET_ENDPOINT_HALT                                   8
#define     CLEAR_NAK_OUT_PACKETS                               7
#define     CLEAR_EP_HIDE_STATUS_PHASE                          6
#define     CLEAR_EP_FORCE_CRC_ERROR                            5
#define     CLEAR_INTERRUPT_MODE                                4
#define     CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE                3
#define     CLEAR_NAK_OUT_PACKETS_MODE                          2
#define     CLEAR_ENDPOINT_TOGGLE                               1
#define     CLEAR_ENDPOINT_HALT                                 0
        __le32                  ep_irqenb;
#define     SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE              6
#define     SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE           5
#define     DATA_PACKET_RECEIVED_INTERRUPT_ENABLE               3
#define     DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE            2
#define     DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE                1
#define     DATA_IN_TOKEN_INTERRUPT_ENABLE                      0
        __le32                  ep_stat;
#define     FIFO_VALID_COUNT                                    24
#define     HIGH_BANDWIDTH_OUT_TRANSACTION_PID                  22
#define     TIMEOUT                                             21
#define     USB_STALL_SENT                                      20
#define     USB_IN_NAK_SENT                                     19
#define     USB_IN_ACK_RCVD                                     18
#define     USB_OUT_PING_NAK_SENT                               17
#define     USB_OUT_ACK_SENT                                    16
#define     FIFO_OVERFLOW                                       13
#define     FIFO_UNDERFLOW                                      12
#define     FIFO_FULL                                           11
#define     FIFO_EMPTY                                          10
#define     FIFO_FLUSH                                          9
#define     SHORT_PACKET_OUT_DONE_INTERRUPT                     6
#define     SHORT_PACKET_TRANSFERRED_INTERRUPT                  5
#define     NAK_OUT_PACKETS                                     4
#define     DATA_PACKET_RECEIVED_INTERRUPT                      3
#define     DATA_PACKET_TRANSMITTED_INTERRUPT                   2
#define     DATA_OUT_PING_TOKEN_INTERRUPT                       1
#define     DATA_IN_TOKEN_INTERRUPT                             0
        // offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0
        __le32                  ep_avail;
        __le32                  ep_data;
        u32                     _unused0[2];
} __attribute__ ((packed));
 
struct net2280_reg_write {
        __le16 port;
        __le32 addr;
        __le32 val;
} __attribute__ ((packed));
 
struct net2280_reg_read {
        __le16 port;
        __le32 addr;
} __attribute__ ((packed));
#endif /* NET2280_H */

Browse

Tools

Subversion Repositories test_project

[/] [test_project/] [trunk/] [linux_sd_driver/] [drivers/] [net/] [wireless/] [net2280.h] - Blame information for rev 62

Line No.	Rev	Author	Line
1	62	marcus.erl	`#ifndef NET2280_H`
2			`#define NET2280_H`
3			`/*`
4			`* NetChip 2280 high/full speed USB device controller.`
5			`* Unlike many such controllers, this one talks PCI.`
6			`*/`
7
8			`/*`
9			`* Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com)`
10			`* Copyright (C) 2003 David Brownell`
11			`*`
12			`* This program is free software; you can redistribute it and/or modify`
13			`* it under the terms of the GNU General Public License as published by`
14			`* the Free Software Foundation; either version 2 of the License, or`
15			`* (at your option) any later version.`
16			`*`
17			`* This program is distributed in the hope that it will be useful,`
18			`* but WITHOUT ANY WARRANTY; without even the implied warranty of`
19			`* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the`
20			`* GNU General Public License for more details.`
21			`*`
22			`* You should have received a copy of the GNU General Public License`
23			`* along with this program; if not, write to the Free Software`
24			`* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA`
25			`*/`
26
27			`/-------------------------------------------------------------------------/`
28
29			`/* NET2280 MEMORY MAPPED REGISTERS`
30			`*`
31			`* The register layout came from the chip documentation, and the bit`
32			`* number definitions were extracted from chip specification.`
33			`*`
34			`* Use the shift operator ('<<') to build bit masks, with readl/writel`
35			`* to access the registers through PCI.`
36			`*/`
37
38			`/* main registers, BAR0 + 0x0000 */`
39			`struct net2280_regs {`
40			`// offset 0x0000`
41			`__le32 devinit;`
42			`#define LOCAL_CLOCK_FREQUENCY 8`
43			`#define FORCE_PCI_RESET 7`
44			`#define PCI_ID 6`
45			`#define PCI_ENABLE 5`
46			`#define FIFO_SOFT_RESET 4`
47			`#define CFG_SOFT_RESET 3`
48			`#define PCI_SOFT_RESET 2`
49			`#define USB_SOFT_RESET 1`
50			`#define M8051_RESET 0`
51			`__le32 eectl;`
52			`#define EEPROM_ADDRESS_WIDTH 23`
53			`#define EEPROM_CHIP_SELECT_ACTIVE 22`
54			`#define EEPROM_PRESENT 21`
55			`#define EEPROM_VALID 20`
56			`#define EEPROM_BUSY 19`
57			`#define EEPROM_CHIP_SELECT_ENABLE 18`
58			`#define EEPROM_BYTE_READ_START 17`
59			`#define EEPROM_BYTE_WRITE_START 16`
60			`#define EEPROM_READ_DATA 8`
61			`#define EEPROM_WRITE_DATA 0`
62			`__le32 eeclkfreq;`
63			`u32 _unused0;`
64			`// offset 0x0010`
65
66			`__le32 pciirqenb0; /* interrupt PCI master ... */`
67			`#define SETUP_PACKET_INTERRUPT_ENABLE 7`
68			`#define ENDPOINT_F_INTERRUPT_ENABLE 6`
69			`#define ENDPOINT_E_INTERRUPT_ENABLE 5`
70			`#define ENDPOINT_D_INTERRUPT_ENABLE 4`
71			`#define ENDPOINT_C_INTERRUPT_ENABLE 3`
72			`#define ENDPOINT_B_INTERRUPT_ENABLE 2`
73			`#define ENDPOINT_A_INTERRUPT_ENABLE 1`
74			`#define ENDPOINT_0_INTERRUPT_ENABLE 0`
75			`__le32 pciirqenb1;`
76			`#define PCI_INTERRUPT_ENABLE 31`
77			`#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27`
78			`#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26`
79			`#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25`
80			`#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20`
81			`#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19`
82			`#define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18`
83			`#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17`
84			`#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16`
85			`#define GPIO_INTERRUPT_ENABLE 13`
86			`#define DMA_D_INTERRUPT_ENABLE 12`
87			`#define DMA_C_INTERRUPT_ENABLE 11`
88			`#define DMA_B_INTERRUPT_ENABLE 10`
89			`#define DMA_A_INTERRUPT_ENABLE 9`
90			`#define EEPROM_DONE_INTERRUPT_ENABLE 8`
91			`#define VBUS_INTERRUPT_ENABLE 7`
92			`#define CONTROL_STATUS_INTERRUPT_ENABLE 6`
93			`#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4`
94			`#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3`
95			`#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2`
96			`#define RESUME_INTERRUPT_ENABLE 1`
97			`#define SOF_INTERRUPT_ENABLE 0`
98			`__le32 cpu_irqenb0; /* ... or onboard 8051 */`
99			`#define SETUP_PACKET_INTERRUPT_ENABLE 7`
100			`#define ENDPOINT_F_INTERRUPT_ENABLE 6`
101			`#define ENDPOINT_E_INTERRUPT_ENABLE 5`
102			`#define ENDPOINT_D_INTERRUPT_ENABLE 4`
103			`#define ENDPOINT_C_INTERRUPT_ENABLE 3`
104			`#define ENDPOINT_B_INTERRUPT_ENABLE 2`
105			`#define ENDPOINT_A_INTERRUPT_ENABLE 1`
106			`#define ENDPOINT_0_INTERRUPT_ENABLE 0`
107			`__le32 cpu_irqenb1;`
108			`#define CPU_INTERRUPT_ENABLE 31`
109			`#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27`
110			`#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26`
111			`#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25`
112			`#define PCI_INTA_INTERRUPT_ENABLE 24`
113			`#define PCI_PME_INTERRUPT_ENABLE 23`
114			`#define PCI_SERR_INTERRUPT_ENABLE 22`
115			`#define PCI_PERR_INTERRUPT_ENABLE 21`
116			`#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20`
117			`#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19`
118			`#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17`
119			`#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16`
120			`#define GPIO_INTERRUPT_ENABLE 13`
121			`#define DMA_D_INTERRUPT_ENABLE 12`
122			`#define DMA_C_INTERRUPT_ENABLE 11`
123			`#define DMA_B_INTERRUPT_ENABLE 10`
124			`#define DMA_A_INTERRUPT_ENABLE 9`
125			`#define EEPROM_DONE_INTERRUPT_ENABLE 8`
126			`#define VBUS_INTERRUPT_ENABLE 7`
127			`#define CONTROL_STATUS_INTERRUPT_ENABLE 6`
128			`#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4`
129			`#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3`
130			`#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2`
131			`#define RESUME_INTERRUPT_ENABLE 1`
132			`#define SOF_INTERRUPT_ENABLE 0`
133
134			`// offset 0x0020`
135			`u32 _unused1;`
136			`__le32 usbirqenb1;`
137			`#define USB_INTERRUPT_ENABLE 31`
138			`#define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27`
139			`#define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26`
140			`#define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25`
141			`#define PCI_INTA_INTERRUPT_ENABLE 24`
142			`#define PCI_PME_INTERRUPT_ENABLE 23`
143			`#define PCI_SERR_INTERRUPT_ENABLE 22`
144			`#define PCI_PERR_INTERRUPT_ENABLE 21`
145			`#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20`
146			`#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19`
147			`#define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17`
148			`#define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16`
149			`#define GPIO_INTERRUPT_ENABLE 13`
150			`#define DMA_D_INTERRUPT_ENABLE 12`
151			`#define DMA_C_INTERRUPT_ENABLE 11`
152			`#define DMA_B_INTERRUPT_ENABLE 10`
153			`#define DMA_A_INTERRUPT_ENABLE 9`
154			`#define EEPROM_DONE_INTERRUPT_ENABLE 8`
155			`#define VBUS_INTERRUPT_ENABLE 7`
156			`#define CONTROL_STATUS_INTERRUPT_ENABLE 6`
157			`#define ROOT_PORT_RESET_INTERRUPT_ENABLE 4`
158			`#define SUSPEND_REQUEST_INTERRUPT_ENABLE 3`
159			`#define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2`
160			`#define RESUME_INTERRUPT_ENABLE 1`
161			`#define SOF_INTERRUPT_ENABLE 0`
162			`__le32 irqstat0;`
163			`#define INTA_ASSERTED 12`
164			`#define SETUP_PACKET_INTERRUPT 7`
165			`#define ENDPOINT_F_INTERRUPT 6`
166			`#define ENDPOINT_E_INTERRUPT 5`
167			`#define ENDPOINT_D_INTERRUPT 4`
168			`#define ENDPOINT_C_INTERRUPT 3`
169			`#define ENDPOINT_B_INTERRUPT 2`
170			`#define ENDPOINT_A_INTERRUPT 1`
171			`#define ENDPOINT_0_INTERRUPT 0`
172			`__le32 irqstat1;`
173			`#define POWER_STATE_CHANGE_INTERRUPT 27`
174			`#define PCI_ARBITER_TIMEOUT_INTERRUPT 26`
175			`#define PCI_PARITY_ERROR_INTERRUPT 25`
176			`#define PCI_INTA_INTERRUPT 24`
177			`#define PCI_PME_INTERRUPT 23`
178			`#define PCI_SERR_INTERRUPT 22`
179			`#define PCI_PERR_INTERRUPT 21`
180			`#define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20`
181			`#define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19`
182			`#define PCI_RETRY_ABORT_INTERRUPT 17`
183			`#define PCI_MASTER_CYCLE_DONE_INTERRUPT 16`
184			`#define GPIO_INTERRUPT 13`
185			`#define DMA_D_INTERRUPT 12`
186			`#define DMA_C_INTERRUPT 11`
187			`#define DMA_B_INTERRUPT 10`
188			`#define DMA_A_INTERRUPT 9`
189			`#define EEPROM_DONE_INTERRUPT 8`
190			`#define VBUS_INTERRUPT 7`
191			`#define CONTROL_STATUS_INTERRUPT 6`
192			`#define ROOT_PORT_RESET_INTERRUPT 4`
193			`#define SUSPEND_REQUEST_INTERRUPT 3`
194			`#define SUSPEND_REQUEST_CHANGE_INTERRUPT 2`
195			`#define RESUME_INTERRUPT 1`
196			`#define SOF_INTERRUPT 0`
197			`// offset 0x0030`
198			`__le32 idxaddr;`
199			`__le32 idxdata;`
200			`__le32 fifoctl;`
201			`#define PCI_BASE2_RANGE 16`
202			`#define IGNORE_FIFO_AVAILABILITY 3`
203			`#define PCI_BASE2_SELECT 2`
204			`#define FIFO_CONFIGURATION_SELECT 0`
205			`u32 _unused2;`
206			`// offset 0x0040`
207			`__le32 memaddr;`
208			`#define START 28`
209			`#define DIRECTION 27`
210			`#define FIFO_DIAGNOSTIC_SELECT 24`
211			`#define MEMORY_ADDRESS 0`
212			`__le32 memdata0;`
213			`__le32 memdata1;`
214			`u32 _unused3;`
215			`// offset 0x0050`
216			`__le32 gpioctl;`
217			`#define GPIO3_LED_SELECT 12`
218			`#define GPIO3_INTERRUPT_ENABLE 11`
219			`#define GPIO2_INTERRUPT_ENABLE 10`
220			`#define GPIO1_INTERRUPT_ENABLE 9`
221			`#define GPIO0_INTERRUPT_ENABLE 8`
222			`#define GPIO3_OUTPUT_ENABLE 7`
223			`#define GPIO2_OUTPUT_ENABLE 6`
224			`#define GPIO1_OUTPUT_ENABLE 5`
225			`#define GPIO0_OUTPUT_ENABLE 4`
226			`#define GPIO3_DATA 3`
227			`#define GPIO2_DATA 2`
228			`#define GPIO1_DATA 1`
229			`#define GPIO0_DATA 0`
230			`__le32 gpiostat;`
231			`#define GPIO3_INTERRUPT 3`
232			`#define GPIO2_INTERRUPT 2`
233			`#define GPIO1_INTERRUPT 1`
234			`#define GPIO0_INTERRUPT 0`
235			`} __attribute__ ((packed));`
236
237			`/* usb control, BAR0 + 0x0080 */`
238			`struct net2280_usb_regs {`
239			`// offset 0x0080`
240			`__le32 stdrsp;`
241			`#define STALL_UNSUPPORTED_REQUESTS 31`
242			`#define SET_TEST_MODE 16`
243			`#define GET_OTHER_SPEED_CONFIGURATION 15`
244			`#define GET_DEVICE_QUALIFIER 14`
245			`#define SET_ADDRESS 13`
246			`#define ENDPOINT_SET_CLEAR_HALT 12`
247			`#define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11`
248			`#define GET_STRING_DESCRIPTOR_2 10`
249			`#define GET_STRING_DESCRIPTOR_1 9`
250			`#define GET_STRING_DESCRIPTOR_0 8`
251			`#define GET_SET_INTERFACE 6`
252			`#define GET_SET_CONFIGURATION 5`
253			`#define GET_CONFIGURATION_DESCRIPTOR 4`
254			`#define GET_DEVICE_DESCRIPTOR 3`
255			`#define GET_ENDPOINT_STATUS 2`
256			`#define GET_INTERFACE_STATUS 1`
257			`#define GET_DEVICE_STATUS 0`
258			`__le32 prodvendid;`
259			`#define PRODUCT_ID 16`
260			`#define VENDOR_ID 0`
261			`__le32 relnum;`
262			`__le32 usbctl;`
263			`#define SERIAL_NUMBER_INDEX 16`
264			`#define PRODUCT_ID_STRING_ENABLE 13`
265			`#define VENDOR_ID_STRING_ENABLE 12`
266			`#define USB_ROOT_PORT_WAKEUP_ENABLE 11`
267			`#define VBUS_PIN 10`
268			`#define TIMED_DISCONNECT 9`
269			`#define SUSPEND_IMMEDIATELY 7`
270			`#define SELF_POWERED_USB_DEVICE 6`
271			`#define REMOTE_WAKEUP_SUPPORT 5`
272			`#define PME_POLARITY 4`
273			`#define USB_DETECT_ENABLE 3`
274			`#define PME_WAKEUP_ENABLE 2`
275			`#define DEVICE_REMOTE_WAKEUP_ENABLE 1`
276			`#define SELF_POWERED_STATUS 0`
277			`// offset 0x0090`
278			`__le32 usbstat;`
279			`#define HIGH_SPEED 7`
280			`#define FULL_SPEED 6`
281			`#define GENERATE_RESUME 5`
282			`#define GENERATE_DEVICE_REMOTE_WAKEUP 4`
283			`__le32 xcvrdiag;`
284			`#define FORCE_HIGH_SPEED_MODE 31`
285			`#define FORCE_FULL_SPEED_MODE 30`
286			`#define USB_TEST_MODE 24`
287			`#define LINE_STATE 16`
288			`#define TRANSCEIVER_OPERATION_MODE 2`
289			`#define TRANSCEIVER_SELECT 1`
290			`#define TERMINATION_SELECT 0`
291			`__le32 setup0123;`
292			`__le32 setup4567;`
293			`// offset 0x0090`
294			`u32 _unused0;`
295			`__le32 ouraddr;`
296			`#define FORCE_IMMEDIATE 7`
297			`#define OUR_USB_ADDRESS 0`
298			`__le32 ourconfig;`
299			`} __attribute__ ((packed));`
300
301			`/* pci control, BAR0 + 0x0100 */`
302			`struct net2280_pci_regs {`
303			`// offset 0x0100`
304			`__le32 pcimstctl;`
305			`#define PCI_ARBITER_PARK_SELECT 13`
306			`#define PCI_MULTI LEVEL_ARBITER 12`
307			`#define PCI_RETRY_ABORT_ENABLE 11`
308			`#define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10`
309			`#define DMA_READ_MULTIPLE_ENABLE 9`
310			`#define DMA_READ_LINE_ENABLE 8`
311			`#define PCI_MASTER_COMMAND_SELECT 6`
312			`#define MEM_READ_OR_WRITE 0`
313			`#define IO_READ_OR_WRITE 1`
314			`#define CFG_READ_OR_WRITE 2`
315			`#define PCI_MASTER_START 5`
316			`#define PCI_MASTER_READ_WRITE 4`
317			`#define PCI_MASTER_WRITE 0`
318			`#define PCI_MASTER_READ 1`
319			`#define PCI_MASTER_BYTE_WRITE_ENABLES 0`
320			`__le32 pcimstaddr;`
321			`__le32 pcimstdata;`
322			`__le32 pcimststat;`
323			`#define PCI_ARBITER_CLEAR 2`
324			`#define PCI_EXTERNAL_ARBITER 1`
325			`#define PCI_HOST_MODE 0`
326			`} __attribute__ ((packed));`
327
328			`/* dma control, BAR0 + 0x0180 ... array of four structs like this,`
329			`* for channels 0..3. see also struct net2280_dma: descriptor`
330			`* that can be loaded into some of these registers.`
331			`*/`
332			`struct net2280_dma_regs { /* [11.7] */`
333			`// offset 0x0180, 0x01a0, 0x01c0, 0x01e0,`
334			`__le32 dmactl;`
335			`#define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25`
336			`#define DMA_CLEAR_COUNT_ENABLE 21`
337			`#define DESCRIPTOR_POLLING_RATE 19`
338			`#define POLL_CONTINUOUS 0`
339			`#define POLL_1_USEC 1`
340			`#define POLL_100_USEC 2`
341			`#define POLL_1_MSEC 3`
342			`#define DMA_VALID_BIT_POLLING_ENABLE 18`
343			`#define DMA_VALID_BIT_ENABLE 17`
344			`#define DMA_SCATTER_GATHER_ENABLE 16`
345			`#define DMA_OUT_AUTO_START_ENABLE 4`
346			`#define DMA_PREEMPT_ENABLE 3`
347			`#define DMA_FIFO_VALIDATE 2`
348			`#define DMA_ENABLE 1`
349			`#define DMA_ADDRESS_HOLD 0`
350			`__le32 dmastat;`
351			`#define DMA_SCATTER_GATHER_DONE_INTERRUPT 25`
352			`#define DMA_TRANSACTION_DONE_INTERRUPT 24`
353			`#define DMA_ABORT 1`
354			`#define DMA_START 0`
355			`u32 _unused0[2];`
356			`// offset 0x0190, 0x01b0, 0x01d0, 0x01f0,`
357			`__le32 dmacount;`
358			`#define VALID_BIT 31`
359			`#define DMA_DIRECTION 30`
360			`#define DMA_DONE_INTERRUPT_ENABLE 29`
361			`#define END_OF_CHAIN 28`
362			`#define DMA_BYTE_COUNT_MASK ((1<<24)-1)`
363			`#define DMA_BYTE_COUNT 0`
364			`__le32 dmaaddr;`
365			`__le32 dmadesc;`
366			`u32 _unused1;`
367			`} __attribute__ ((packed));`
368
369			`/* dedicated endpoint registers, BAR0 + 0x0200 */`
370
371			`struct net2280_dep_regs { /* [11.8] */`
372			`// offset 0x0200, 0x0210, 0x220, 0x230, 0x240`
373			`__le32 dep_cfg;`
374			`// offset 0x0204, 0x0214, 0x224, 0x234, 0x244`
375			`__le32 dep_rsp;`
376			`u32 _unused[2];`
377			`} __attribute__ ((packed));`
378
379			`/* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs`
380			`* like this, for ep0 then the configurable endpoints A..F`
381			`* ep0 reserved for control; E and F have only 64 bytes of fifo`
382			`*/`
383			`struct net2280_ep_regs { /* [11.9] */`
384			`// offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0`
385			`__le32 ep_cfg;`
386			`#define ENDPOINT_BYTE_COUNT 16`
387			`#define ENDPOINT_ENABLE 10`
388			`#define ENDPOINT_TYPE 8`
389			`#define ENDPOINT_DIRECTION 7`
390			`#define ENDPOINT_NUMBER 0`
391			`__le32 ep_rsp;`
392			`#define SET_NAK_OUT_PACKETS 15`
393			`#define SET_EP_HIDE_STATUS_PHASE 14`
394			`#define SET_EP_FORCE_CRC_ERROR 13`
395			`#define SET_INTERRUPT_MODE 12`
396			`#define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11`
397			`#define SET_NAK_OUT_PACKETS_MODE 10`
398			`#define SET_ENDPOINT_TOGGLE 9`
399			`#define SET_ENDPOINT_HALT 8`
400			`#define CLEAR_NAK_OUT_PACKETS 7`
401			`#define CLEAR_EP_HIDE_STATUS_PHASE 6`
402			`#define CLEAR_EP_FORCE_CRC_ERROR 5`
403			`#define CLEAR_INTERRUPT_MODE 4`
404			`#define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3`
405			`#define CLEAR_NAK_OUT_PACKETS_MODE 2`
406			`#define CLEAR_ENDPOINT_TOGGLE 1`
407			`#define CLEAR_ENDPOINT_HALT 0`
408			`__le32 ep_irqenb;`
409			`#define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6`
410			`#define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5`
411			`#define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3`
412			`#define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2`
413			`#define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1`
414			`#define DATA_IN_TOKEN_INTERRUPT_ENABLE 0`
415			`__le32 ep_stat;`
416			`#define FIFO_VALID_COUNT 24`
417			`#define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22`
418			`#define TIMEOUT 21`
419			`#define USB_STALL_SENT 20`
420			`#define USB_IN_NAK_SENT 19`
421			`#define USB_IN_ACK_RCVD 18`
422			`#define USB_OUT_PING_NAK_SENT 17`
423			`#define USB_OUT_ACK_SENT 16`
424			`#define FIFO_OVERFLOW 13`
425			`#define FIFO_UNDERFLOW 12`
426			`#define FIFO_FULL 11`
427			`#define FIFO_EMPTY 10`
428			`#define FIFO_FLUSH 9`
429			`#define SHORT_PACKET_OUT_DONE_INTERRUPT 6`
430			`#define SHORT_PACKET_TRANSFERRED_INTERRUPT 5`
431			`#define NAK_OUT_PACKETS 4`
432			`#define DATA_PACKET_RECEIVED_INTERRUPT 3`
433			`#define DATA_PACKET_TRANSMITTED_INTERRUPT 2`
434			`#define DATA_OUT_PING_TOKEN_INTERRUPT 1`
435			`#define DATA_IN_TOKEN_INTERRUPT 0`
436			`// offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0`
437			`__le32 ep_avail;`
438			`__le32 ep_data;`
439			`u32 _unused0[2];`
440			`} __attribute__ ((packed));`
441
442			`struct net2280_reg_write {`
443			`__le16 port;`
444			`__le32 addr;`
445			`__le32 val;`
446			`} __attribute__ ((packed));`
447
448			`struct net2280_reg_read {`
449			`__le16 port;`
450			`__le32 addr;`
451			`} __attribute__ ((packed));`
452			`#endif /* NET2280_H */`