URL https://opencores.org/ocsvn/test_project/test_project/trunk
Subversion Repositories test_project

[/] [test_project/] [trunk/] [linux_sd_driver/] [drivers/] [pcmcia/] [ti113x.h] - Blame information for rev 78

Go to most recent revision | Details | Compare with Previous | View Log

/*
 * ti113x.h 1.16 1999/10/25 20:03:34
 *
 * The contents of this file are subject to the Mozilla Public License
 * Version 1.1 (the "License"); you may not use this file except in
 * compliance with the License. You may obtain a copy of the License
 * at http://www.mozilla.org/MPL/
 *
 * Software distributed under the License is distributed on an "AS IS"
 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
 * the License for the specific language governing rights and
 * limitations under the License.
 *
 * The initial developer of the original code is David A. Hinds
 * <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
 * are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
 *
 * Alternatively, the contents of this file may be used under the
 * terms of the GNU General Public License version 2 (the "GPL"), in which
 * case the provisions of the GPL are applicable instead of the
 * above.  If you wish to allow the use of your version of this file
 * only under the terms of the GPL and not to allow others to use
 * your version of this file under the MPL, indicate your decision by
 * deleting the provisions above and replace them with the notice and
 * other provisions required by the GPL.  If you do not delete the
 * provisions above, a recipient may use your version of this file
 * under either the MPL or the GPL.
 */
 
#ifndef _LINUX_TI113X_H
#define _LINUX_TI113X_H
 
 
/* Register definitions for TI 113X PCI-to-CardBus bridges */
 
/* System Control Register */
#define TI113X_SYSTEM_CONTROL           0x0080  /* 32 bit */
#define  TI113X_SCR_SMIROUTE            0x04000000
#define  TI113X_SCR_SMISTATUS           0x02000000
#define  TI113X_SCR_SMIENB              0x01000000
#define  TI113X_SCR_VCCPROT             0x00200000
#define  TI113X_SCR_REDUCEZV            0x00100000
#define  TI113X_SCR_CDREQEN             0x00080000
#define  TI113X_SCR_CDMACHAN            0x00070000
#define  TI113X_SCR_SOCACTIVE           0x00002000
#define  TI113X_SCR_PWRSTREAM           0x00000800
#define  TI113X_SCR_DELAYUP             0x00000400
#define  TI113X_SCR_DELAYDOWN           0x00000200
#define  TI113X_SCR_INTERROGATE         0x00000100
#define  TI113X_SCR_CLKRUN_SEL          0x00000080
#define  TI113X_SCR_PWRSAVINGS          0x00000040
#define  TI113X_SCR_SUBSYSRW            0x00000020
#define  TI113X_SCR_CB_DPAR             0x00000010
#define  TI113X_SCR_CDMA_EN             0x00000008
#define  TI113X_SCR_ASYNC_IRQ           0x00000004
#define  TI113X_SCR_KEEPCLK             0x00000002
#define  TI113X_SCR_CLKRUN_ENA          0x00000001  
 
#define  TI122X_SCR_SER_STEP            0xc0000000
#define  TI122X_SCR_INTRTIE             0x20000000
#define  TIXX21_SCR_TIEALL              0x10000000
#define  TI122X_SCR_CBRSVD              0x00400000
#define  TI122X_SCR_MRBURSTDN           0x00008000
#define  TI122X_SCR_MRBURSTUP           0x00004000
#define  TI122X_SCR_RIMUX               0x00000001
 
/* Multimedia Control Register */
#define TI1250_MULTIMEDIA_CTL           0x0084  /* 8 bit */
#define  TI1250_MMC_ZVOUTEN             0x80
#define  TI1250_MMC_PORTSEL             0x40
#define  TI1250_MMC_ZVEN1               0x02
#define  TI1250_MMC_ZVEN0               0x01
 
#define TI1250_GENERAL_STATUS           0x0085  /* 8 bit */
#define TI1250_GPIO0_CONTROL            0x0088  /* 8 bit */
#define TI1250_GPIO1_CONTROL            0x0089  /* 8 bit */
#define TI1250_GPIO2_CONTROL            0x008a  /* 8 bit */
#define TI1250_GPIO3_CONTROL            0x008b  /* 8 bit */
#define TI1250_GPIO_MODE_MASK           0xc0
 
/* IRQMUX/MFUNC Register */
#define TI122X_MFUNC                    0x008c  /* 32 bit */
#define TI122X_MFUNC0_MASK              0x0000000f
#define TI122X_MFUNC1_MASK              0x000000f0
#define TI122X_MFUNC2_MASK              0x00000f00
#define TI122X_MFUNC3_MASK              0x0000f000
#define TI122X_MFUNC4_MASK              0x000f0000
#define TI122X_MFUNC5_MASK              0x00f00000
#define TI122X_MFUNC6_MASK              0x0f000000
 
#define TI122X_MFUNC0_INTA              0x00000002
#define TI125X_MFUNC0_INTB              0x00000001
#define TI122X_MFUNC1_INTB              0x00000020
#define TI122X_MFUNC3_IRQSER            0x00001000
 
 
/* Retry Status Register */
#define TI113X_RETRY_STATUS             0x0090  /* 8 bit */
#define  TI113X_RSR_PCIRETRY            0x80
#define  TI113X_RSR_CBRETRY             0x40
#define  TI113X_RSR_TEXP_CBB            0x20
#define  TI113X_RSR_MEXP_CBB            0x10
#define  TI113X_RSR_TEXP_CBA            0x08
#define  TI113X_RSR_MEXP_CBA            0x04
#define  TI113X_RSR_TEXP_PCI            0x02
#define  TI113X_RSR_MEXP_PCI            0x01
 
/* Card Control Register */
#define TI113X_CARD_CONTROL             0x0091  /* 8 bit */
#define  TI113X_CCR_RIENB               0x80
#define  TI113X_CCR_ZVENABLE            0x40
#define  TI113X_CCR_PCI_IRQ_ENA         0x20
#define  TI113X_CCR_PCI_IREQ            0x10
#define  TI113X_CCR_PCI_CSC             0x08
#define  TI113X_CCR_SPKROUTEN           0x02
#define  TI113X_CCR_IFG                 0x01
 
#define  TI1220_CCR_PORT_SEL            0x20
#define  TI122X_CCR_AUD2MUX             0x04
 
/* Device Control Register */
#define TI113X_DEVICE_CONTROL           0x0092  /* 8 bit */
#define  TI113X_DCR_5V_FORCE            0x40
#define  TI113X_DCR_3V_FORCE            0x20
#define  TI113X_DCR_IMODE_MASK          0x06
#define  TI113X_DCR_IMODE_ISA           0x02
#define  TI113X_DCR_IMODE_SERIAL        0x04
 
#define  TI12XX_DCR_IMODE_PCI_ONLY      0x00
#define  TI12XX_DCR_IMODE_ALL_SERIAL    0x06
 
/* Buffer Control Register */
#define TI113X_BUFFER_CONTROL           0x0093  /* 8 bit */
#define  TI113X_BCR_CB_READ_DEPTH       0x08
#define  TI113X_BCR_CB_WRITE_DEPTH      0x04
#define  TI113X_BCR_PCI_READ_DEPTH      0x02
#define  TI113X_BCR_PCI_WRITE_DEPTH     0x01
 
/* Diagnostic Register */
#define TI1250_DIAGNOSTIC               0x0093  /* 8 bit */
#define  TI1250_DIAG_TRUE_VALUE         0x80
#define  TI1250_DIAG_PCI_IREQ           0x40
#define  TI1250_DIAG_PCI_CSC            0x20
#define  TI1250_DIAG_ASYNC_CSC          0x01
 
/* DMA Registers */
#define TI113X_DMA_0                    0x0094  /* 32 bit */
#define TI113X_DMA_1                    0x0098  /* 32 bit */
 
/* ExCA IO offset registers */
#define TI113X_IO_OFFSET(map)           (0x36+((map)<<1))
 
/* EnE test register */
#define ENE_TEST_C9                     0xc9    /* 8bit */
#define ENE_TEST_C9_TLTENABLE           0x02
#define ENE_TEST_C9_PFENABLE_F0         0x04
#define ENE_TEST_C9_PFENABLE_F1         0x08
#define ENE_TEST_C9_PFENABLE            (ENE_TEST_C9_PFENABLE_F0 | ENE_TEST_C9_PFENABLE_F0)
#define ENE_TEST_C9_WPDISALBLE_F0       0x40
#define ENE_TEST_C9_WPDISALBLE_F1       0x80
#define ENE_TEST_C9_WPDISALBLE          (ENE_TEST_C9_WPDISALBLE_F0 | ENE_TEST_C9_WPDISALBLE_F1)
 
/*
 * Texas Instruments CardBus controller overrides.
 */
#define ti_sysctl(socket)       ((socket)->private[0])
#define ti_cardctl(socket)      ((socket)->private[1])
#define ti_devctl(socket)       ((socket)->private[2])
#define ti_diag(socket)         ((socket)->private[3])
#define ti_mfunc(socket)        ((socket)->private[4])
#define ene_test_c9(socket)     ((socket)->private[5])
 
/*
 * These are the TI specific power management handlers.
 */
static void ti_save_state(struct yenta_socket *socket)
{
        ti_sysctl(socket) = config_readl(socket, TI113X_SYSTEM_CONTROL);
        ti_mfunc(socket) = config_readl(socket, TI122X_MFUNC);
        ti_cardctl(socket) = config_readb(socket, TI113X_CARD_CONTROL);
        ti_devctl(socket) = config_readb(socket, TI113X_DEVICE_CONTROL);
        ti_diag(socket) = config_readb(socket, TI1250_DIAGNOSTIC);
 
        if (socket->dev->vendor == PCI_VENDOR_ID_ENE)
                ene_test_c9(socket) = config_readb(socket, ENE_TEST_C9);
}
 
static void ti_restore_state(struct yenta_socket *socket)
{
        config_writel(socket, TI113X_SYSTEM_CONTROL, ti_sysctl(socket));
        config_writel(socket, TI122X_MFUNC, ti_mfunc(socket));
        config_writeb(socket, TI113X_CARD_CONTROL, ti_cardctl(socket));
        config_writeb(socket, TI113X_DEVICE_CONTROL, ti_devctl(socket));
        config_writeb(socket, TI1250_DIAGNOSTIC, ti_diag(socket));
 
        if (socket->dev->vendor == PCI_VENDOR_ID_ENE)
                config_writeb(socket, ENE_TEST_C9, ene_test_c9(socket));
}
 
/*
 *      Zoom video control for TI122x/113x chips
 */
 
static void ti_zoom_video(struct pcmcia_socket *sock, int onoff)
{
        u8 reg;
        struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
 
        /* If we don't have a Zoom Video switch this is harmless,
           we just tristate the unused (ZV) lines */
        reg = config_readb(socket, TI113X_CARD_CONTROL);
        if (onoff)
                /* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
                reg |= TI113X_CCR_ZVENABLE;
        else
                reg &= ~TI113X_CCR_ZVENABLE;
        config_writeb(socket, TI113X_CARD_CONTROL, reg);
}
 
/*
 *      The 145x series can also use this. They have an additional
 *      ZV autodetect mode we don't use but don't actually need.
 *      FIXME: manual says its in func0 and func1 but disagrees with
 *      itself about this - do we need to force func0, if so we need
 *      to know a lot more about socket pairings in pcmcia_socket than
 *      we do now.. uggh.
 */
 
static void ti1250_zoom_video(struct pcmcia_socket *sock, int onoff)
{
        struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
        int shift = 0;
        u8 reg;
 
        ti_zoom_video(sock, onoff);
 
        reg = config_readb(socket, TI1250_MULTIMEDIA_CTL);
        reg |= TI1250_MMC_ZVOUTEN;      /* ZV bus enable */
 
        if(PCI_FUNC(socket->dev->devfn)==1)
                shift = 1;
 
        if(onoff)
        {
                reg &= ~(1<<6);         /* Clear select bit */
                reg |= shift<<6;        /* Favour our socket */
                reg |= 1<<shift;        /* Socket zoom video on */
        }
        else
        {
                reg &= ~(1<<6);         /* Clear select bit */
                reg |= (1^shift)<<6;    /* Favour other socket */
                reg &= ~(1<<shift);     /* Socket zoon video off */
        }
 
        config_writeb(socket, TI1250_MULTIMEDIA_CTL, reg);
}
 
static void ti_set_zv(struct yenta_socket *socket)
{
        if(socket->dev->vendor == PCI_VENDOR_ID_TI)
        {
                switch(socket->dev->device)
                {
                        /* There may be more .. */
                        case PCI_DEVICE_ID_TI_1220:
                        case PCI_DEVICE_ID_TI_1221:
                        case PCI_DEVICE_ID_TI_1225:
                        case PCI_DEVICE_ID_TI_4510:
                                socket->socket.zoom_video = ti_zoom_video;
                                break;
                        case PCI_DEVICE_ID_TI_1250:
                        case PCI_DEVICE_ID_TI_1251A:
                        case PCI_DEVICE_ID_TI_1251B:
                        case PCI_DEVICE_ID_TI_1450:
                                socket->socket.zoom_video = ti1250_zoom_video;
                }
        }
}
 
 
/*
 * Generic TI init - TI has an extension for the
 * INTCTL register that sets the PCI CSC interrupt.
 * Make sure we set it correctly at open and init
 * time
 * - override: disable the PCI CSC interrupt. This makes
 *   it possible to use the CSC interrupt to probe the
 *   ISA interrupts.
 * - init: set the interrupt to match our PCI state.
 *   This makes us correctly get PCI CSC interrupt
 *   events.
 */
static int ti_init(struct yenta_socket *socket)
{
        u8 new, reg = exca_readb(socket, I365_INTCTL);
 
        new = reg & ~I365_INTR_ENA;
        if (socket->cb_irq)
                new |= I365_INTR_ENA;
        if (new != reg)
                exca_writeb(socket, I365_INTCTL, new);
        return 0;
}
 
static int ti_override(struct yenta_socket *socket)
{
        u8 new, reg = exca_readb(socket, I365_INTCTL);
 
        new = reg & ~I365_INTR_ENA;
        if (new != reg)
                exca_writeb(socket, I365_INTCTL, new);
 
        ti_set_zv(socket);
 
        return 0;
}
 
static int ti113x_override(struct yenta_socket *socket)
{
        u8 cardctl;
 
        cardctl = config_readb(socket, TI113X_CARD_CONTROL);
        cardctl &= ~(TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_IREQ | TI113X_CCR_PCI_CSC);
        if (socket->cb_irq)
                cardctl |= TI113X_CCR_PCI_IRQ_ENA | TI113X_CCR_PCI_CSC | TI113X_CCR_PCI_IREQ;
        config_writeb(socket, TI113X_CARD_CONTROL, cardctl);
 
        return ti_override(socket);
}
 
 
/* irqrouting for func0, probes PCI interrupt and ISA interrupts */
static void ti12xx_irqroute_func0(struct yenta_socket *socket)
{
        u32 mfunc, mfunc_old, devctl;
        u8 gpio3, gpio3_old;
        int pci_irq_status;
 
        mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
        devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
        printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
               pci_name(socket->dev), mfunc, devctl);
 
        /* make sure PCI interrupts are enabled before probing */
        ti_init(socket);
 
        /* test PCI interrupts first. only try fixing if return value is 0! */
        pci_irq_status = yenta_probe_cb_irq(socket);
        if (pci_irq_status)
                goto out;
 
        /*
         * We're here which means PCI interrupts are _not_ delivered. try to
         * find the right setting (all serial or parallel)
         */
        printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
               pci_name(socket->dev));
 
        /* for serial PCI make sure MFUNC3 is set to IRQSER */
        if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
                switch (socket->dev->device) {
                case PCI_DEVICE_ID_TI_1250:
                case PCI_DEVICE_ID_TI_1251A:
                case PCI_DEVICE_ID_TI_1251B:
                case PCI_DEVICE_ID_TI_1450:
                case PCI_DEVICE_ID_TI_1451A:
                case PCI_DEVICE_ID_TI_4450:
                case PCI_DEVICE_ID_TI_4451:
                        /* these chips have no IRQSER setting in MFUNC3  */
                        break;
 
                default:
                        mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
 
                        /* write down if changed, probe */
                        if (mfunc != mfunc_old) {
                                config_writel(socket, TI122X_MFUNC, mfunc);
 
                                pci_irq_status = yenta_probe_cb_irq(socket);
                                if (pci_irq_status == 1) {
                                        printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts ok\n",
                                               pci_name(socket->dev));
                                        mfunc_old = mfunc;
                                        goto out;
                                }
 
                                /* not working, back to old value */
                                mfunc = mfunc_old;
                                config_writel(socket, TI122X_MFUNC, mfunc);
 
                                if (pci_irq_status == -1)
                                        goto out;
                        }
                }
 
                /* serial PCI interrupts not working fall back to parallel */
                printk(KERN_INFO "Yenta TI: socket %s falling back to parallel PCI interrupts\n",
                       pci_name(socket->dev));
                devctl &= ~TI113X_DCR_IMODE_MASK;
                devctl |= TI113X_DCR_IMODE_SERIAL; /* serial ISA could be right */
                config_writeb(socket, TI113X_DEVICE_CONTROL, devctl);
        }
 
        /* parallel PCI interrupts: route INTA */
        switch (socket->dev->device) {
        case PCI_DEVICE_ID_TI_1250:
        case PCI_DEVICE_ID_TI_1251A:
        case PCI_DEVICE_ID_TI_1251B:
        case PCI_DEVICE_ID_TI_1450:
                /* make sure GPIO3 is set to INTA */
                gpio3 = gpio3_old = config_readb(socket, TI1250_GPIO3_CONTROL);
                gpio3 &= ~TI1250_GPIO_MODE_MASK;
                if (gpio3 != gpio3_old)
                        config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
                break;
 
        default:
                gpio3 = gpio3_old = 0;
 
                mfunc = (mfunc & ~TI122X_MFUNC0_MASK) | TI122X_MFUNC0_INTA;
                if (mfunc != mfunc_old)
                        config_writel(socket, TI122X_MFUNC, mfunc);
        }
 
        /* time to probe again */
        pci_irq_status = yenta_probe_cb_irq(socket);
        if (pci_irq_status == 1) {
                mfunc_old = mfunc;
                printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
                       pci_name(socket->dev));
        } else {
                /* not working, back to old value */
                mfunc = mfunc_old;
                config_writel(socket, TI122X_MFUNC, mfunc);
                if (gpio3 != gpio3_old)
                        config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3_old);
        }
 
out:
        if (pci_irq_status < 1) {
                socket->cb_irq = 0;
                printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
                       pci_name(socket->dev));
        }
}
 
 
/* changes the irq of func1 to match that of func0 */
static int ti12xx_align_irqs(struct yenta_socket *socket, int *old_irq)
{
        struct pci_dev *func0;
 
        /* find func0 device */
        func0 = pci_get_slot(socket->dev->bus, socket->dev->devfn & ~0x07);
        if (!func0)
                return 0;
 
        if (old_irq)
                *old_irq = socket->cb_irq;
        socket->cb_irq = socket->dev->irq = func0->irq;
 
        pci_dev_put(func0);
 
        return 1;
}
 
/*
 * ties INTA and INTB together. also changes the devices irq to that of
 * the function 0 device. call from func1 only.
 * returns 1 if INTRTIE changed, 0 otherwise.
 */
static int ti12xx_tie_interrupts(struct yenta_socket *socket, int *old_irq)
{
        u32 sysctl;
        int ret;
 
        sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
        if (sysctl & TI122X_SCR_INTRTIE)
                return 0;
 
        /* align */
        ret = ti12xx_align_irqs(socket, old_irq);
        if (!ret)
                return 0;
 
        /* tie */
        sysctl |= TI122X_SCR_INTRTIE;
        config_writel(socket, TI113X_SYSTEM_CONTROL, sysctl);
 
        return 1;
}
 
/* undo what ti12xx_tie_interrupts() did */
static void ti12xx_untie_interrupts(struct yenta_socket *socket, int old_irq)
{
        u32 sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
        sysctl &= ~TI122X_SCR_INTRTIE;
        config_writel(socket, TI113X_SYSTEM_CONTROL, sysctl);
 
        socket->cb_irq = socket->dev->irq = old_irq;
}
 
/*
 * irqrouting for func1, plays with INTB routing
 * only touches MFUNC for INTB routing. all other bits are taken
 * care of in func0 already.
 */
static void ti12xx_irqroute_func1(struct yenta_socket *socket)
{
        u32 mfunc, mfunc_old, devctl, sysctl;
        int pci_irq_status;
 
        mfunc = mfunc_old = config_readl(socket, TI122X_MFUNC);
        devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
        printk(KERN_INFO "Yenta TI: socket %s, mfunc 0x%08x, devctl 0x%02x\n",
               pci_name(socket->dev), mfunc, devctl);
 
        /* if IRQs are configured as tied, align irq of func1 with func0 */
        sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
        if (sysctl & TI122X_SCR_INTRTIE)
                ti12xx_align_irqs(socket, NULL);
 
        /* make sure PCI interrupts are enabled before probing */
        ti_init(socket);
 
        /* test PCI interrupts first. only try fixing if return value is 0! */
        pci_irq_status = yenta_probe_cb_irq(socket);
        if (pci_irq_status)
                goto out;
 
        /*
         * We're here which means PCI interrupts are _not_ delivered. try to
         * find the right setting
         */
        printk(KERN_INFO "Yenta TI: socket %s probing PCI interrupt failed, trying to fix\n",
               pci_name(socket->dev));
 
 
        /* if all serial: set INTRTIE, probe again */
        if ((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) {
                int old_irq;
 
                if (ti12xx_tie_interrupts(socket, &old_irq)) {
                        pci_irq_status = yenta_probe_cb_irq(socket);
                        if (pci_irq_status == 1) {
                                printk(KERN_INFO "Yenta TI: socket %s all-serial interrupts, tied ok\n",
                                       pci_name(socket->dev));
                                goto out;
                        }
 
                        ti12xx_untie_interrupts(socket, old_irq);
                }
        }
        /* parallel PCI: route INTB, probe again */
        else {
                int old_irq;
 
                switch (socket->dev->device) {
                case PCI_DEVICE_ID_TI_1250:
                        /* the 1250 has one pin for IRQSER/INTB depending on devctl */
                        break;
 
                case PCI_DEVICE_ID_TI_1251A:
                case PCI_DEVICE_ID_TI_1251B:
                case PCI_DEVICE_ID_TI_1450:
                        /*
                         *  those have a pin for IRQSER/INTB plus INTB in MFUNC0
                         *  we alread probed the shared pin, now go for MFUNC0
                         */
                        mfunc = (mfunc & ~TI122X_MFUNC0_MASK) | TI125X_MFUNC0_INTB;
                        break;
 
                default:
                        mfunc = (mfunc & ~TI122X_MFUNC1_MASK) | TI122X_MFUNC1_INTB;
                        break;
                }
 
                /* write, probe */
                if (mfunc != mfunc_old) {
                        config_writel(socket, TI122X_MFUNC, mfunc);
 
                        pci_irq_status = yenta_probe_cb_irq(socket);
                        if (pci_irq_status == 1) {
                                printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts ok\n",
                                       pci_name(socket->dev));
                                goto out;
                        }
 
                        mfunc = mfunc_old;
                        config_writel(socket, TI122X_MFUNC, mfunc);
 
                        if (pci_irq_status == -1)
                                goto out;
                }
 
                /* still nothing: set INTRTIE */
                if (ti12xx_tie_interrupts(socket, &old_irq)) {
                        pci_irq_status = yenta_probe_cb_irq(socket);
                        if (pci_irq_status == 1) {
                                printk(KERN_INFO "Yenta TI: socket %s parallel PCI interrupts, tied ok\n",
                                       pci_name(socket->dev));
                                goto out;
                        }
 
                        ti12xx_untie_interrupts(socket, old_irq);
                }
        }
 
out:
        if (pci_irq_status < 1) {
                socket->cb_irq = 0;
                printk(KERN_INFO "Yenta TI: socket %s no PCI interrupts. Fish. Please report.\n",
                       pci_name(socket->dev));
        }
}
 
 
/* Returns true value if the second slot of a two-slot controller is empty */
static int ti12xx_2nd_slot_empty(struct yenta_socket *socket)
{
        struct pci_dev *func;
        struct yenta_socket *slot2;
        int devfn;
        unsigned int state;
        int ret = 1;
        u32 sysctl;
 
        /* catch the two-slot controllers */
        switch (socket->dev->device) {
        case PCI_DEVICE_ID_TI_1220:
        case PCI_DEVICE_ID_TI_1221:
        case PCI_DEVICE_ID_TI_1225:
        case PCI_DEVICE_ID_TI_1251A:
        case PCI_DEVICE_ID_TI_1251B:
        case PCI_DEVICE_ID_TI_1420:
        case PCI_DEVICE_ID_TI_1450:
        case PCI_DEVICE_ID_TI_1451A:
        case PCI_DEVICE_ID_TI_1520:
        case PCI_DEVICE_ID_TI_1620:
        case PCI_DEVICE_ID_TI_4520:
        case PCI_DEVICE_ID_TI_4450:
        case PCI_DEVICE_ID_TI_4451:
                /*
                 * there are way more, but they need to be added in yenta_socket.c
                 * and pci_ids.h first anyway.
                 */
                break;
 
        case PCI_DEVICE_ID_TI_XX12:
        case PCI_DEVICE_ID_TI_X515:
        case PCI_DEVICE_ID_TI_X420:
        case PCI_DEVICE_ID_TI_X620:
        case PCI_DEVICE_ID_TI_XX21_XX11:
        case PCI_DEVICE_ID_TI_7410:
        case PCI_DEVICE_ID_TI_7610:
                /*
                 * those are either single or dual slot CB with additional functions
                 * like 1394, smartcard reader, etc. check the TIEALL flag for them
                 * the TIEALL flag binds the IRQ of all functions toghether.
                 * we catch the single slot variants later.
                 */
                sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
                if (sysctl & TIXX21_SCR_TIEALL)
                        return 0;
 
                break;
 
        /* single-slot controllers have the 2nd slot empty always :) */
        default:
                return 1;
        }
 
        /* get other slot */
        devfn = socket->dev->devfn & ~0x07;
        func = pci_get_slot(socket->dev->bus,
                            (socket->dev->devfn & 0x07) ? devfn : devfn | 0x01);
        if (!func)
                return 1;
 
        /*
         * check that the device id of both slots match. this is needed for the
         * XX21 and the XX11 controller that share the same device id for single
         * and dual slot controllers. return '2nd slot empty'. we already checked
         * if the interrupt is tied to another function.
         */
        if (socket->dev->device != func->device)
                goto out;
 
        slot2 = pci_get_drvdata(func);
        if (!slot2)
                goto out;
 
        /* check state */
        yenta_get_status(&socket->socket, &state);
        if (state & SS_DETECT) {
                ret = 0;
                goto out;
        }
 
out:
        pci_dev_put(func);
        return ret;
}
 
/*
 * TI specifiy parts for the power hook.
 *
 * some TI's with some CB's produces interrupt storm on power on. it has been
 * seen with atheros wlan cards on TI1225 and TI1410. solution is simply to
 * disable any CB interrupts during this time.
 */
static int ti12xx_power_hook(struct pcmcia_socket *sock, int operation)
{
        struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
        u32 mfunc, devctl, sysctl;
        u8 gpio3;
 
        /* only POWER_PRE and POWER_POST are interesting */
        if ((operation != HOOK_POWER_PRE) && (operation != HOOK_POWER_POST))
                return 0;
 
        devctl = config_readb(socket, TI113X_DEVICE_CONTROL);
        sysctl = config_readl(socket, TI113X_SYSTEM_CONTROL);
        mfunc = config_readl(socket, TI122X_MFUNC);
 
        /*
         * all serial/tied: only disable when modparm set. always doing it
         * would mean a regression for working setups 'cos it disables the
         * interrupts for both both slots on 2-slot controllers
         * (and users of single slot controllers where it's save have to
         * live with setting the modparm, most don't have to anyway)
         */
        if (((devctl & TI113X_DCR_IMODE_MASK) == TI12XX_DCR_IMODE_ALL_SERIAL) &&
            (pwr_irqs_off || ti12xx_2nd_slot_empty(socket))) {
                switch (socket->dev->device) {
                case PCI_DEVICE_ID_TI_1250:
                case PCI_DEVICE_ID_TI_1251A:
                case PCI_DEVICE_ID_TI_1251B:
                case PCI_DEVICE_ID_TI_1450:
                case PCI_DEVICE_ID_TI_1451A:
                case PCI_DEVICE_ID_TI_4450:
                case PCI_DEVICE_ID_TI_4451:
                        /* these chips have no IRQSER setting in MFUNC3  */
                        break;
 
                default:
                        if (operation == HOOK_POWER_PRE)
                                mfunc = (mfunc & ~TI122X_MFUNC3_MASK);
                        else
                                mfunc = (mfunc & ~TI122X_MFUNC3_MASK) | TI122X_MFUNC3_IRQSER;
                }
 
                return 0;
        }
 
        /* do the job differently for func0/1 */
        if ((PCI_FUNC(socket->dev->devfn) == 0) ||
            ((sysctl & TI122X_SCR_INTRTIE) &&
             (pwr_irqs_off || ti12xx_2nd_slot_empty(socket)))) {
                /* some bridges are different */
                switch (socket->dev->device) {
                case PCI_DEVICE_ID_TI_1250:
                case PCI_DEVICE_ID_TI_1251A:
                case PCI_DEVICE_ID_TI_1251B:
                case PCI_DEVICE_ID_TI_1450:
                        /* those oldies use gpio3 for INTA */
                        gpio3 = config_readb(socket, TI1250_GPIO3_CONTROL);
                        if (operation == HOOK_POWER_PRE)
                                gpio3 = (gpio3 & ~TI1250_GPIO_MODE_MASK) | 0x40;
                        else
                                gpio3 &= ~TI1250_GPIO_MODE_MASK;
                        config_writeb(socket, TI1250_GPIO3_CONTROL, gpio3);
                        break;
 
                default:
                        /* all new bridges are the same */
                        if (operation == HOOK_POWER_PRE)
                                mfunc &= ~TI122X_MFUNC0_MASK;
                        else
                                mfunc |= TI122X_MFUNC0_INTA;
                        config_writel(socket, TI122X_MFUNC, mfunc);
                }
        } else {
                switch (socket->dev->device) {
                case PCI_DEVICE_ID_TI_1251A:
                case PCI_DEVICE_ID_TI_1251B:
                case PCI_DEVICE_ID_TI_1450:
                        /* those have INTA elsewhere and INTB in MFUNC0 */
                        if (operation == HOOK_POWER_PRE)
                                mfunc &= ~TI122X_MFUNC0_MASK;
                        else
                                mfunc |= TI125X_MFUNC0_INTB;
                        config_writel(socket, TI122X_MFUNC, mfunc);
 
                        break;
 
                default:
                        /* all new bridges are the same */
                        if (operation == HOOK_POWER_PRE)
                                mfunc &= ~TI122X_MFUNC1_MASK;
                        else
                                mfunc |= TI122X_MFUNC1_INTB;
                        config_writel(socket, TI122X_MFUNC, mfunc);
                }
        }
 
        return 0;
}
 
static int ti12xx_override(struct yenta_socket *socket)
{
        u32 val, val_orig;
 
        /* make sure that memory burst is active */
        val_orig = val = config_readl(socket, TI113X_SYSTEM_CONTROL);
        if (disable_clkrun && PCI_FUNC(socket->dev->devfn) == 0) {
                printk(KERN_INFO "Yenta: Disabling CLKRUN feature\n");
                val |= TI113X_SCR_KEEPCLK;
        }
        if (!(val & TI122X_SCR_MRBURSTUP)) {
                printk(KERN_INFO "Yenta: Enabling burst memory read transactions\n");
                val |= TI122X_SCR_MRBURSTUP;
        }
        if (val_orig != val)
                config_writel(socket, TI113X_SYSTEM_CONTROL, val);
 
        /*
         * Yenta expects controllers to use CSCINT to route
         * CSC interrupts to PCI rather than INTVAL.
         */
        val = config_readb(socket, TI1250_DIAGNOSTIC);
        printk(KERN_INFO "Yenta: Using %s to route CSC interrupts to PCI\n",
                (val & TI1250_DIAG_PCI_CSC) ? "CSCINT" : "INTVAL");
        printk(KERN_INFO "Yenta: Routing CardBus interrupts to %s\n",
                (val & TI1250_DIAG_PCI_IREQ) ? "PCI" : "ISA");
 
        /* do irqrouting, depending on function */
        if (PCI_FUNC(socket->dev->devfn) == 0)
                ti12xx_irqroute_func0(socket);
        else
                ti12xx_irqroute_func1(socket);
 
        /* install power hook */
        socket->socket.power_hook = ti12xx_power_hook;
 
        return ti_override(socket);
}
 
 
static int ti1250_override(struct yenta_socket *socket)
{
        u8 old, diag;
 
        old = config_readb(socket, TI1250_DIAGNOSTIC);
        diag = old & ~(TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ);
        if (socket->cb_irq)
                diag |= TI1250_DIAG_PCI_CSC | TI1250_DIAG_PCI_IREQ;
 
        if (diag != old) {
                printk(KERN_INFO "Yenta: adjusting diagnostic: %02x -> %02x\n",
                        old, diag);
                config_writeb(socket, TI1250_DIAGNOSTIC, diag);
        }
 
        return ti12xx_override(socket);
}
 
 
/**
 * EnE specific part. EnE bridges are register compatible with TI bridges but
 * have their own test registers and more important their own little problems.
 * Some fixup code to make everybody happy (TM).
 */
 
#ifdef CONFIG_YENTA_ENE_TUNE
/*
 * set/clear various test bits:
 * Defaults to clear the bit.
 * - mask (u8) defines what bits to change
 * - bits (u8) is the values to change them to
 * -> it's
 *      current = (current & ~mask) | bits
 */
/* pci ids of devices that wants to have the bit set */
#define DEVID(_vend,_dev,_subvend,_subdev,mask,bits) {          \
                .vendor         = _vend,                        \
                .device         = _dev,                         \
                .subvendor      = _subvend,                     \
                .subdevice      = _subdev,                      \
                .driver_data    = ((mask) << 8 | (bits)),       \
        }
static struct pci_device_id ene_tune_tbl[] = {
        /* Echo Audio products based on motorola DSP56301 and DSP56361 */
        DEVID(PCI_VENDOR_ID_MOTOROLA, 0x1801, 0xECC0, PCI_ANY_ID,
                ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
        DEVID(PCI_VENDOR_ID_MOTOROLA, 0x3410, 0xECC0, PCI_ANY_ID,
                ENE_TEST_C9_TLTENABLE | ENE_TEST_C9_PFENABLE, ENE_TEST_C9_TLTENABLE),
 
        {}
};
 
static void ene_tune_bridge(struct pcmcia_socket *sock, struct pci_bus *bus)
{
        struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);
        struct pci_dev *dev;
        struct pci_device_id *id = NULL;
        u8 test_c9, old_c9, mask, bits;
 
        list_for_each_entry(dev, &bus->devices, bus_list) {
                id = (struct pci_device_id *) pci_match_id(ene_tune_tbl, dev);
                if (id)
                        break;
        }
 
        test_c9 = old_c9 = config_readb(socket, ENE_TEST_C9);
        if (id) {
                mask = (id->driver_data >> 8) & 0xFF;
                bits = id->driver_data & 0xFF;
 
                test_c9 = (test_c9 & ~mask) | bits;
        }
        else
                /* default to clear TLTEnable bit, old behaviour */
                test_c9 &= ~ENE_TEST_C9_TLTENABLE;
 
        printk(KERN_INFO "yenta EnE: chaning testregister 0xC9, %02x -> %02x\n", old_c9, test_c9);
        config_writeb(socket, ENE_TEST_C9, test_c9);
}
 
static int ene_override(struct yenta_socket *socket)
{
        /* install tune_bridge() function */
        socket->socket.tune_bridge = ene_tune_bridge;
 
        return ti1250_override(socket);
}
#else
#  define ene_override ti1250_override
#endif /* !CONFIG_YENTA_ENE_TUNE */
 
#endif /* _LINUX_TI113X_H */
 
Browse

Tools

Subversion Repositories test_project

[/] [test_project/] [trunk/] [linux_sd_driver/] [drivers/] [pcmcia/] [ti113x.h] - Blame information for rev 78

Line No.	Rev	Author	Line
1	62	marcus.erl	`/*`
2			`* ti113x.h 1.16 1999/10/25 20:03:34`
3			`*`
4			`* The contents of this file are subject to the Mozilla Public License`
5			`* Version 1.1 (the "License"); you may not use this file except in`
6			`* compliance with the License. You may obtain a copy of the License`
7			`* at http://www.mozilla.org/MPL/`
8			`*`
9			`* Software distributed under the License is distributed on an "AS IS"`
10			`* basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See`
11			`* the License for the specific language governing rights and`
12			`* limitations under the License.`
13			`*`
14			`* The initial developer of the original code is David A. Hinds`
15			`* <dahinds@users.sourceforge.net>. Portions created by David A. Hinds`
16			`* are Copyright (C) 1999 David A. Hinds. All Rights Reserved.`
17			`*`
18			`* Alternatively, the contents of this file may be used under the`
19			`* terms of the GNU General Public License version 2 (the "GPL"), in which`
20			`* case the provisions of the GPL are applicable instead of the`
21			`* above. If you wish to allow the use of your version of this file`
22			`* only under the terms of the GPL and not to allow others to use`
23			`* your version of this file under the MPL, indicate your decision by`
24			`* deleting the provisions above and replace them with the notice and`
25			`* other provisions required by the GPL. If you do not delete the`
26			`* provisions above, a recipient may use your version of this file`
27			`* under either the MPL or the GPL.`
28			`*/`
29
30			`#ifndef _LINUX_TI113X_H`
31			`#define _LINUX_TI113X_H`
32
33
34			`/* Register definitions for TI 113X PCI-to-CardBus bridges */`
35
36			`/* System Control Register */`
37			`#define TI113X_SYSTEM_CONTROL 0x0080 /* 32 bit */`
38			`#define TI113X_SCR_SMIROUTE 0x04000000`
39			`#define TI113X_SCR_SMISTATUS 0x02000000`
40			`#define TI113X_SCR_SMIENB 0x01000000`