Subversion Repositories wbddr3

////////////////////////////////////////////////////////////////////////////////

//

// Filename:    wbddrsdram.v

//

// Project:     OpenArty, an entirely open SoC based upon the Arty platform

//

// Purpose:     

//

// Creator:     Dan Gisselquist, Ph.D.

//              Gisselquist Technology, LLC

//

////////////////////////////////////////////////////////////////////////////////

//

// Copyright (C) 2015-2016, Gisselquist Technology, LLC

//

// This program is free software (firmware): you can redistribute it and/or

// modify it under the terms of  the GNU General Public License as published

// by the Free Software Foundation, either version 3 of the License, or (at

// your option) any later version.

//

// This program is distributed in the hope that it will be useful, but WITHOUT

// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or

// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License

// for more details.

//

// You should have received a copy of the GNU General Public License along

// with this program.  (It's in the $(ROOT)/doc directory, run make with no

// target there if the PDF file isn't present.)  If not, see

// <http://www.gnu.org/licenses/> for a copy.

//

// License:     GPL, v3, as defined and found on www.gnu.org,

//              http://www.gnu.org/licenses/gpl.html

//

//

////////////////////////////////////////////////////////////////////////////////

//

//

// Possible commands to the DDR3 memory.  These consist of settings for the

// bits: o_wb_cs_n, o_wb_ras_n, o_wb_cas_n, and o_wb_we_n, respectively.

`define DDR_MRSET       4'b0000

`define DDR_REFRESH     4'b0001

`define DDR_PRECHARGE   4'b0010

`define DDR_ACTIVATE    4'b0011

`define DDR_WRITE       4'b0100

`define DDR_READ        4'b0101

`define DDR_ZQS         4'b0110

`define DDR_NOOP        4'b0111

//`define       DDR_DESELECT    4'b1???

//

// In this controller, 24-bit commands tend to be passed around.  These 

// 'commands' are bit fields.  Here we specify the bits associated with

// the bit fields.

`define DDR_RSTDONE     24      // End the reset sequence?

`define DDR_RSTTIMER    23      // Does this reset command take multiple clocks?

`define DDR_RSTBIT      22      // Value to place on reset_n

`define DDR_CKEBIT      21      // Should this reset command set CKE?

//

// Refresh command bit fields

`define DDR_NEEDREFRESH 23

`define DDR_RFTIMER     22

`define DDR_RFBEGIN     21

//

`define DDR_CMDLEN      21

`define DDR_CSBIT       20

`define DDR_RASBIT      19

`define DDR_CASBIT      18

`define DDR_WEBIT       17

`define DDR_NOPTIMER    16      // Steal this from BA bits

`define DDR_BABITS      3       // BABITS are really from 18:16, they are 3 bits

`define DDR_ADDR_BITS   14

//

`define BUSREG  7

`define BUSNOW  8

module  wbddrsdram(i_clk, i_reset,

                i_wb_cyc, i_wb_stb, i_wb_we, i_wb_addr, i_wb_data,

                        o_wb_ack, o_wb_stall, o_wb_data,

                o_ddr_reset_n, o_ddr_cke,

                o_ddr_cs_n, o_ddr_ras_n, o_ddr_cas_n, o_ddr_we_n,

                o_ddr_dqs, o_ddr_dm, o_ddr_odt, o_ddr_bus_oe,

                o_ddr_addr, o_ddr_ba, o_ddr_data, i_ddr_data);

        parameter       CKRBITS = 13, // Bits in CKREFI4

                        CKREFI4 = 13'd6240, // 4 * 7.8us at 200 MHz clock

                        CKRFC = 320,

                        CKWR = 3,

                        CKXPR = CKRFC+5+2; // Clocks per tXPR timeout

        input                   i_clk, i_reset;

        // Wishbone inputs

        input                   i_wb_cyc, i_wb_stb, i_wb_we;

        input           [25:0]   i_wb_addr;

        input           [31:0]   i_wb_data;

        // Wishbone outputs

        output  reg             o_wb_ack;

        output  reg             o_wb_stall;

        output  reg     [31:0]   o_wb_data;

        // DDR3 RAM Controller

        output  reg             o_ddr_reset_n, o_ddr_cke;

        // Control outputs

        output  wire            o_ddr_cs_n, o_ddr_ras_n, o_ddr_cas_n,o_ddr_we_n;

        // DQS outputs:set to 3'b010 when data is active, 3'b100 (i.e. 2'bzz) ow

        output  wire            o_ddr_dqs;

        output  reg             o_ddr_dm;

        output  reg             o_ddr_odt;

        output  wire            o_ddr_bus_oe;

        // Address outputs

        output  wire    [13:0]   o_ddr_addr;

        output  wire    [2:0]    o_ddr_ba;

        // And the data inputs and outputs

        output  reg     [31:0]   o_ddr_data;

        input           [31:0]   i_ddr_data;

        reg             drive_dqs;

        // The pending transaction

        reg     [31:0]   r_data;

        reg             r_pending, r_we;

        reg     [25:0]   r_addr;

        reg     [13:0]   r_row;

        reg     [2:0]    r_bank;

        reg     [9:0]    r_col;

        reg     [1:0]    r_sub;

        reg             r_move; // It was accepted, and can move to next stage

        // The pending transaction, one further into the pipeline.  This is

        // the stage where the read/write command is actually given to the

        // interface if we haven't stalled.

        reg     [31:0]   s_data;

        reg             s_pending, s_we; // , s_match;

        reg     [25:0]   s_addr;

        reg     [13:0]   s_row, s_nxt_row;

        reg     [2:0]    s_bank, s_nxt_bank;

        reg     [9:0]    s_col;

        reg     [1:0]    s_sub;

        // Can the pending transaction be satisfied with the current (ongoing)

        // transaction?

        reg             m_move, m_match, m_pending, m_we;

        reg     [25:0]   m_addr;

        reg     [13:0]   m_row;

        reg     [2:0]    m_bank;

        reg     [9:0]    m_col;

        reg     [1:0]    m_sub;

        // Can we preload the next bank?

        reg     [13:0]   r_nxt_row;

        reg     [2:0]    r_nxt_bank;

        reg     need_close_bank, need_close_this_bank,

                        last_close_bank, maybe_close_next_bank,

                        last_maybe_close,

                need_open_bank, last_open_bank, maybe_open_next_bank,

                        last_maybe_open,

                valid_bank, last_valid_bank;

        reg     [(`DDR_CMDLEN-1):0]      close_bank_cmd, activate_bank_cmd,

                                        maybe_close_cmd, maybe_open_cmd, rw_cmd;

        reg     [1:0]    rw_sub;

        reg             rw_we;

        wire    w_this_closing_bank, w_this_opening_bank,

                w_this_maybe_close, w_this_maybe_open,

                w_this_rw_move;

        reg     last_closing_bank, last_opening_bank;

        wire    w_need_close_this_bank, w_need_open_bank,

                w_r_valid, w_s_valid;

//

// tWTR = 7.5

// tRRD = 7.5

// tREFI= 7.8

// tFAW = 45

// tRTP = 7.5

// tCKE = 5.625

// tRFC = 160

// tRP  = 13.5

// tRAS = 36

// tRCD = 13.5

//

// RESET:

//      1. Hold o_reset_n = 1'b0; for 200 us, or 40,000 clocks (65536 perhaps?)

//              Hold cke low during this time as well

//              The clock should be free running into the chip during this time

//              Leave command in NOOP state: {cs,ras,cas,we} = 4'h7;

//              ODT must be held low

//      2. Hold cke low for another 500us, or 100,000 clocks

//      3. Raise CKE, continue outputting a NOOP for

//              tXPR, tDLLk, and tZQInit

//      4. Load MRS2, wait tMRD

//      4. Load MRS3, wait tMRD

//      4. Load MRS1, wait tMOD

// Before using the SDRAM, we'll need to program at least 3 of the mode

//      registers, if not all 4. 

//   tMOD clocks are required to program the mode registers, during which

//      time the RAM must be idle.

//

// NOOP: CS low, RAS, CAS, and WE high

//

// Reset logic should be simple, and is given as follows:

// note that it depends upon a ROM memory, reset_mem, and an address into that

// memory: reset_address.  Each memory location provides either a "command" to

// the DDR3 SDRAM, or a timer to wait until the next command.  Further, the

// timer commands indicate whether or not the command during the timer is to

// be set to idle, or whether the command is instead left as it was.

        reg             reset_override, reset_ztimer, maintenance_override;

        reg     [4:0]    reset_address;

        reg     [(`DDR_CMDLEN-1):0]      reset_cmd, cmd, refresh_cmd,

                                        maintenance_cmd;

        reg     [24:0]   reset_instruction;

        reg     [16:0]   reset_timer;

        initial reset_override = 1'b1;

        initial reset_address  = 5'h0;

        always @(posedge i_clk)

                if (i_reset)

                begin

                        reset_override <= 1'b1;

                        reset_cmd <= { `DDR_NOOP, reset_instruction[16:0]};

                end else if (reset_ztimer)

                begin

                        if (reset_instruction[`DDR_RSTDONE])

                                reset_override <= 1'b0;

                        reset_cmd <= reset_instruction[20:0];

                end

        initial reset_ztimer = 1'b0;    // Is the timer zero?

        initial reset_timer = 17'h02;

        always @(posedge i_clk)

                if (i_reset)

                begin

                        reset_ztimer <= 1'b0;

                        reset_timer <= 17'd2;

                end else if (!reset_ztimer)

                begin

                        reset_ztimer <= (reset_timer == 17'h01);

                        reset_timer <= reset_timer - 17'h01;

                end else if (reset_instruction[`DDR_RSTTIMER])

                begin

                        reset_ztimer <= 1'b0;

                        reset_timer <= reset_instruction[16:0];

                end

        wire    [16:0]   w_ckXPR = CKXPR, w_ckRST = 4, w_ckRP = 3,

                        w_ckRFC = CKRFC;

        always @(posedge i_clk)

                if (i_reset)

                        reset_instruction <= { 4'h4, `DDR_NOOP, 17'd40_000 };

                else if (reset_ztimer) case(reset_address) // RSTDONE, TIMER, CKE, ??

                // 1. Reset asserted (active low) for 200 us. (@200MHz)

                5'h0: reset_instruction <= { 4'h4, `DDR_NOOP, 17'd40_000 };

                // 2. Reset de-asserted, wait 500 us before asserting CKE

                5'h1: reset_instruction <= { 4'h6, `DDR_NOOP, 17'd100_000 };

                // 3. Assert CKE, wait minimum of Reset CKE Exit time

                5'h2: reset_instruction <= { 4'h7, `DDR_NOOP, w_ckXPR };

                // 4. Look MR2.  (1CK, no TIMER)

                5'h3: reset_instruction <= { 4'h3, `DDR_MRSET, 3'h2,

                        3'h0, 2'b00, 1'b0, 1'b0, 1'b1, 3'b0, 3'b0 }; // MRS2

                // 3. Wait 4 clocks (tMRD)

                5'h4: reset_instruction <= { 4'h7, `DDR_NOOP, 17'h02 };

                // 5. Set MR1

                5'h5: reset_instruction <= { 4'h3, `DDR_MRSET, 3'h1,

                        1'h0, // Reserved for Future Use (RFU)

                        1'b0, // Qoff - output buffer enabled

                        1'b1, // TDQS ... enabled

                        1'b0, // RFU

                        1'b0, // High order bit, Rtt_Nom (3'b011)

                        1'b0, // RFU

                        //

                        1'b0, // Disable write-leveling

                        1'b1, // Mid order bit of Rtt_Nom

                        1'b0, // High order bit of Output Drvr Impedence Ctrl

                        2'b0, // Additive latency = 0

                        1'b1, // Low order bit of Rtt_Nom

                        1'b1, // DIC set to 2'b01

                        1'b1 }; // MRS1, DLL enable

                // 7. Wait another 4 clocks

                5'h6: reset_instruction <= { 4'h7, `DDR_NOOP, 17'h02 };

                // 8. Send MRS0

                5'h7: reset_instruction <= { 4'h3, `DDR_MRSET, 3'h0,

                        1'b0, // Reserved for future use

                        1'b0, // PPD control, (slow exit(DLL off))

                        3'b1, // Write recovery for auto precharge

                        1'b0, // DLL Reset (No)

                        //

                        1'b0, // TM mode normal

                        3'b01, // High 3-bits, CAS latency (=4'b0010 = 4'd5)

                        1'b0, // Read burst type = nibble sequential

                        1'b0, // Low bit of cas latency

                        2'b0 }; // Burst length = 8 (Fixed)

                // 9. Wait tMOD, is max(12 clocks, 15ns)

                5'h8: reset_instruction <= { 4'h7, `DDR_NOOP, 17'h0a };

                // 10. Issue a ZQCL command to start ZQ calibration, A10 is high

                5'h9: reset_instruction <= { 4'h3, `DDR_ZQS, 6'h0, 1'b1, 10'h0};

                //11.Wait for both tDLLK and tZQinit completed, both are 512 cks

                5'ha: reset_instruction <= { 4'h7, `DDR_NOOP, 17'd512 };

                // 12. Precharge all command

                5'hb: reset_instruction <= { 4'h3, `DDR_PRECHARGE, 6'h0, 1'b1, 10'h0 };

                // 13. Wait for the precharge to complete

                5'hc: reset_instruction <= { 4'h7, `DDR_NOOP, w_ckRP };

                // 14. A single Auto Refresh commands

                5'hd: reset_instruction <= { 4'h3, `DDR_REFRESH, 17'h00 };

                // 15. Wait for the auto refresh to complete

                5'he: reset_instruction <= { 4'h7, `DDR_NOOP, w_ckRFC };

                // Two Auto Refresh commands

                default:

                        reset_instruction <={4'hb, `DDR_NOOP, 17'd00_000 };

                endcase

                // reset_instruction <= reset_mem[reset_address];

        initial reset_address = 5'h0;

        always @(posedge i_clk)

                if (i_reset)

                        reset_address <= 5'h1;

                else if ((reset_ztimer)&&(reset_override))

                        reset_address <= reset_address + 5'h1;

//

// initial reset_mem =

//       0.     !DONE, TIMER,RESET_N=0, CKE=0, CMD = NOOP, TIMER = 200us ( 40,000)

//       1.     !DONE, TIMER,RESET_N=1, CKE=0, CMD = NOOP, TIMER = 500us (100,000)

//       2.     !DONE, TIMER,RESET_N=1, CKE=1, CMD = NOOP, TIMER = (Look me up)

//       3.     !DONE,!TIMER,RESET_N=1, CKE=1, CMD = MODE, MRS

//       4.     !DONE,!TIMER,RESET_N=1, CKE=1, CMD = NOOP, TIMER = tMRS

//       5.     !DONE,!TIMER,RESET_N=1, CKE=1, CMD = MODE, MRS3

//       6.     !DONE,!TIMER,RESET_N=1, CKE=1, CMD = NOOP, TIMER = tMRS

//       7.     !DONE,!TIMER,RESET_N=1, CKE=1, CMD = MODE, MRS1

//       8.     !DONE,!TIMER,RESET_N=1, CKE=1, CMD = NOOP, TIMER = tMRS

//       9.     !DONE,!TIMER,RESET_N=1, CKE=1, CMD = MODE, MRS1

//      10.     !DONE,!TIMER,RESET_N=1, CKE=1, CMD = NOOP, TIMER = tMOD

//      11.     !DONE,!TIMER,RESET_N=1, CKE=1, (Pre-charge all)

//      12.     !DONE,!TIMER,RESET_N=1, CKE=1, (wait)

//      13.     !DONE,!TIMER,RESET_N=1, CKE=1, (Auto-refresh)

//      14.     !DONE,!TIMER,RESET_N=1, CKE=1, (Auto-refresh)

//      15.     !DONE,!TIMER,RESET_N=1, CKE=1, (wait)

//

//

// Let's keep track of any open banks.  There are 8 of them to keep track of.

//

//      A precharge requires 3 clocks at 200MHz to complete, 2 clocks at 100MHz.

//      

//

//

        reg     need_refresh;

        wire    w_precharge_all;

        reg     banks_are_closing, all_banks_closed;

        reg     [3:0]    bank_status     [0:7];

        reg     [13:0]   bank_address    [0:7];

        reg     [3:0]    bank_wr_ck      [0:7]; // tWTR

        reg             bank_wr_ckzro   [0:7]; // tWTR

        wire    [3:0]    write_recycle_clocks;

        assign  write_recycle_clocks = CKWR+4+4;

        always @(posedge i_clk)

        begin

                bank_status[0] <= { bank_status[0][2:0], bank_status[0][0] };

                bank_status[1] <= { bank_status[1][2:0], bank_status[1][0] };

                bank_status[2] <= { bank_status[2][2:0], bank_status[2][0] };

                bank_status[3] <= { bank_status[3][2:0], bank_status[3][0] };

                bank_status[4] <= { bank_status[4][2:0], bank_status[4][0] };

                bank_status[5] <= { bank_status[5][2:0], bank_status[5][0] };

                bank_status[6] <= { bank_status[6][2:0], bank_status[6][0] };

                bank_status[7] <= { bank_status[7][2:0], bank_status[7][0] };

                all_banks_closed <= (bank_status[0][2:0] == 3'b00)

                                        &&(bank_status[1][2:0] == 3'b00)

                                        &&(bank_status[2][2:0] == 3'b00)

                                        &&(bank_status[3][2:0] == 3'b00)

                                        &&(bank_status[4][2:0] == 3'b00)

                                        &&(bank_status[5][2:0] == 3'b00)

                                        &&(bank_status[6][2:0] == 3'b00)

                                        &&(bank_status[7][2:0] == 3'b00);

                bank_wr_ck[0] <= (|bank_wr_ck[0])?(bank_wr_ck[0]-4'h1):4'h0;

                bank_wr_ck[1] <= (|bank_wr_ck[1])?(bank_wr_ck[1]-4'h1):4'h0;

                bank_wr_ck[2] <= (|bank_wr_ck[2])?(bank_wr_ck[2]-4'h1):4'h0;

                bank_wr_ck[3] <= (|bank_wr_ck[3])?(bank_wr_ck[3]-4'h1):4'h0;

                bank_wr_ck[4] <= (|bank_wr_ck[4])?(bank_wr_ck[4]-4'h1):4'h0;

                bank_wr_ck[5] <= (|bank_wr_ck[5])?(bank_wr_ck[5]-4'h1):4'h0;

                bank_wr_ck[6] <= (|bank_wr_ck[6])?(bank_wr_ck[6]-4'h1):4'h0;

                bank_wr_ck[7] <= (|bank_wr_ck[7])?(bank_wr_ck[7]-4'h1):4'h0;

                bank_wr_ckzro[0] <= (bank_wr_ck[0][3:1]==3'b00);

                bank_wr_ckzro[1] <= (bank_wr_ck[1][3:1]==3'b00);

                bank_wr_ckzro[2] <= (bank_wr_ck[2][3:1]==3'b00);

                bank_wr_ckzro[3] <= (bank_wr_ck[3][3:1]==3'b00);

                bank_wr_ckzro[4] <= (bank_wr_ck[4][3:1]==3'b00);

                bank_wr_ckzro[5] <= (bank_wr_ck[5][3:1]==3'b00);

                bank_wr_ckzro[6] <= (bank_wr_ck[6][3:1]==3'b00);

                bank_wr_ckzro[7] <= (bank_wr_ck[7][3:1]==3'b00);

                if (w_this_rw_move)

                        bank_wr_ck[rw_cmd[16:14]] <= (rw_cmd[`DDR_WEBIT])? 4'h0

                                : write_recycle_clocks;

                if (reset_override)

                begin

                        bank_status[0][0] <= 1'b0;

                        bank_status[1][0] <= 1'b0;

                        bank_status[2][0] <= 1'b0;

                        bank_status[3][0] <= 1'b0;

                        bank_status[4][0] <= 1'b0;

                        bank_status[5][0] <= 1'b0;

                        bank_status[6][0] <= 1'b0;

                        bank_status[7][0] <= 1'b0;

                        banks_are_closing <= 1'b1;

                end else if ((need_refresh)||(w_precharge_all))

                begin

                        bank_status[0][0] <= 1'b0;

                        bank_status[1][0] <= 1'b0;

                        bank_status[2][0] <= 1'b0;

                        bank_status[3][0] <= 1'b0;

                        bank_status[4][0] <= 1'b0;

                        bank_status[5][0] <= 1'b0;

                        bank_status[6][0] <= 1'b0;

                        bank_status[7][0] <= 1'b0;

                        banks_are_closing <= 1'b1;

                end else if (need_close_bank)

                begin

                        bank_status[close_bank_cmd[16:14]]

                                <= { bank_status[close_bank_cmd[16:14]][2:0], 1'b0 };

                        // bank_status[close_bank_cmd[16:14]][0] <= 1'b0;

                end else if (need_open_bank)

                begin

                        bank_status[activate_bank_cmd[16:14]]

                                <= { bank_status[activate_bank_cmd[16:14]][2:0], 1'b1 };

                        // bank_status[activate_bank_cmd[16:14]][0] <= 1'b1;

                        all_banks_closed <= 1'b0;

                        banks_are_closing <= 1'b0;

                end else if ((valid_bank)&&(!r_move))

                        ;

                else if (maybe_close_next_bank)

                begin

                        bank_status[maybe_close_cmd[16:14]]

                                <= { bank_status[maybe_close_cmd[16:14]][2:0], 1'b0 };

                end else if (maybe_open_next_bank)

                begin

                        bank_status[maybe_open_cmd[16:14]]

                                <= { bank_status[maybe_open_cmd[16:14]][2:0], 1'b1 };

                        // bank_status[activate_bank_cmd[16:14]][0] <= 1'b1;

                        all_banks_closed <= 1'b0;

                        banks_are_closing <= 1'b0;

                end

        end

        always @(posedge i_clk)

                // if (cmd[22:19] == `DDR_ACTIVATE)

                if (w_this_opening_bank)

                        bank_address[activate_bank_cmd[16:14]]

                                <= activate_bank_cmd[13:0];

                else if (!w_this_maybe_open)

                        bank_address[maybe_open_cmd[16:14]]

                                <= maybe_open_cmd[13:0];

//

//

// Okay, let's investigate when we need to do a refresh.  Our plan will be to

// do 4 refreshes every tREFI*4 seconds.  tREFI = 7.8us, but its a parameter

// in the number of clocks so that we can handle both 100MHz and 200MHz clocks.

//

// Note that 160ns are needed between refresh commands (JEDEC, p172), or

// 320 clocks @200MHz, or equivalently 160 clocks @100MHz.  Thus to issue 4

// of these refresh cycles will require 4*320=1280 clocks@200 MHz.  After this

// time, no more refreshes will be needed for 6240 clocks.

//

// Let's think this through:

//      REFRESH_COST = (n*(320)+24)/(n*1560)

// 

//

//

        reg             refresh_ztimer;

        reg     [16:0]   refresh_counter;

        reg     [3:0]    refresh_addr;

        reg     [23:0]   refresh_instruction;

        always @(posedge i_clk)

                if (reset_override)

                        refresh_addr <= 4'hf;

                else if (refresh_ztimer)

                        refresh_addr <= refresh_addr + 1;

                else if (refresh_instruction[`DDR_RFBEGIN])

                        refresh_addr <= 4'h0;

        always @(posedge i_clk)

                if (reset_override)

                begin

                        refresh_ztimer <= 1'b1;

                        refresh_counter <= 17'd0;

                end else if (!refresh_ztimer)

                begin

                        refresh_ztimer <= (refresh_counter == 17'h1);

                        refresh_counter <= (refresh_counter - 17'h1);

                end else if (refresh_instruction[`DDR_RFTIMER])

                begin

                        refresh_ztimer <= 1'b0;

                        refresh_counter <= refresh_instruction[16:0];

                end

        wire    [16:0]   w_ckREFIn, w_ckREFRst;

        assign  w_ckREFIn[(CKRBITS-1): 0] = CKREFI4-5*CKRFC-2-10;

        assign  w_ckREFIn[ 16:(CKRBITS)] = 0;

        assign  w_ckREFRst = CKRFC-2-12;

        always @(posedge i_clk)

                if (reset_override)

                        refresh_cmd <= { `DDR_NOOP, w_ckREFIn };

                else if (refresh_ztimer)

                        refresh_cmd <= refresh_instruction[20:0];

        always @(posedge i_clk)

                if (reset_override)

                        need_refresh <= 1'b0;

                else if (refresh_ztimer)

                        need_refresh <= refresh_instruction[`DDR_NEEDREFRESH];

        always @(posedge i_clk)

        if (refresh_ztimer)

                case(refresh_addr)//NEED-RFC, HAVE-TIMER, 

                4'h0: refresh_instruction <= { 3'h2, `DDR_NOOP, w_ckREFIn };

                // 17'd10 = time to complete write, plus write recovery time

                //              minus two (cause we can't count zero or one)

                //      = WL+4+tWR-2 = 10

                //      = 5+4+3-2 = 10

                4'h1: refresh_instruction <= { 3'h6, `DDR_NOOP, 17'd10 };

                4'h2: refresh_instruction <= { 3'h4, `DDR_PRECHARGE, 17'h0400 };

                4'h3: refresh_instruction <= { 3'h6, `DDR_NOOP, 17'd2 };

                4'h4: refresh_instruction <= { 3'h4, `DDR_REFRESH, 17'h00 };

                4'h5: refresh_instruction <= { 3'h6, `DDR_NOOP, w_ckRFC };

                4'h6: refresh_instruction <= { 3'h4, `DDR_REFRESH, 17'h00 };

                4'h7: refresh_instruction <= { 3'h6, `DDR_NOOP, w_ckRFC };

                4'h8: refresh_instruction <= { 3'h4, `DDR_REFRESH, 17'h00 };

                4'h9: refresh_instruction <= { 3'h6, `DDR_NOOP, w_ckRFC };

                4'ha: refresh_instruction <= { 3'h4, `DDR_REFRESH, 17'h00 };

                4'hb: refresh_instruction <= { 3'h6, `DDR_NOOP, w_ckRFC };

                4'hc: refresh_instruction <= { 3'h2, `DDR_NOOP, w_ckREFRst };

                default:

                        refresh_instruction <= { 3'h1, `DDR_NOOP, 17'h00 };

                endcase

//

//

//      Let's track: when will our bus be active?  When will we be reading or

//      writing?