URL https://opencores.org/ocsvn/xulalx25soc/xulalx25soc/trunk

Subversion Repositories xulalx25soc

[/] [xulalx25soc/] [trunk/] [rtl/] [txuart.v] - Blame information for rev 46

Go to most recent revision | Details | Compare with Previous | View Log


////////////////////////////////////////////////////////////////////////////////
//
// Filename:    txuart.v
//
// Project:     XuLA2 board
//
// Purpose:     Transmit outputs over a single UART line.
//
//      To interface with this module, connect it to your system clock,
//      pass it the 32 bit setup register (defined below) and the byte
//      of data you wish to transmit.  Strobe the i_wr line high for one
//      clock cycle, and your data will be off.  Wait until the 'o_busy'
//      line is low before strobing the i_wr line again--this implementation
//      has NO BUFFER, so strobing i_wr while the core is busy will just
//      cause your data to be lost.  The output will be placed on the o_txuart
//      output line.  If you wish to set/send a break condition, assert the
//      i_break line otherwise leave it low.
//
//      There is a synchronous reset line, logic high.
//
//      Now for the setup register.  The register is 32 bits, so that this
//      UART may be set up over a 32-bit bus.
//
//      i_setup[29:28]  Indicates the number of data bits per word.  This will
//      either be 2'b00 for an 8-bit word, 2'b01 for a 7-bit word, 2'b10
//      for a six bit word, or 2'b11 for a five bit word.
//
//      i_setup[27]     Indicates whether or not to use one or two stop bits.
//              Set this to one to expect two stop bits, zero for one.
//
//      i_setup[26]     Indicates whether or not a parity bit exists.  Set this
//              to 1'b1 to include parity.
//
//      i_setup[25]     Indicates whether or not the parity bit is fixed.  Set
//              to 1'b1 to include a fixed bit of parity, 1'b0 to allow the
//              parity to be set based upon data.  (Both assume the parity
//              enable value is set.)
//
//      i_setup[24]     This bit is ignored if parity is not used.  Otherwise,
//              in the case of a fixed parity bit, this bit indicates whether
//              mark (1'b1) or space (1'b0) parity is used.  Likewise if the
//              parity is not fixed, a 1'b1 selects even parity, and 1'b0
//              selects odd.
//
//      i_setup[23:0]   Indicates the speed of the UART in terms of clocks.
//              So, for example, if you have a 200 MHz clock and wish to
//              run your UART at 9600 baud, you would take 200 MHz and divide
//              by 9600 to set this value to 24'd20834.  Likewise if you wished
//              to run this serial port at 115200 baud from a 200 MHz clock,
//              you would set the value to 24'd1736
//
//      Thus, to set the UART for the common setting of an 8-bit word, 
//      one stop bit, no parity, and 115200 baud over a 200 MHz clock, you
//      would want to set the setup value to:
//
//      32'h0006c8              // For 115,200 baud, 8 bit, no parity
//      32'h005161              // For 9600 baud, 8 bit, no parity
//      
//
//
// Creator:     Dan Gisselquist, Ph.D.
//              Gisselquist Technology, LLC
//
////////////////////////////////////////////////////////////////////////////////
//
// Copyright (C) 2015, Gisselquist Technology, LLC
//
// This program is free software (firmware): you can redistribute it and/or
// modify it under the terms of  the GNU General Public License as published
// by the Free Software Foundation, either version 3 of the License, or (at
// your option) any later version.
//
// This program is distributed in the hope that it will be useful, but WITHOUT
// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
// for more details.
//
// License:     GPL, v3, as defined and found on www.gnu.org,
//              http://www.gnu.org/licenses/gpl.html
//
//
////////////////////////////////////////////////////////////////////////////////
//
//
//
`define TXU_BIT_ZERO    4'h0
`define TXU_BIT_ONE     4'h1
`define TXU_BIT_TWO     4'h2
`define TXU_BIT_THREE   4'h3
`define TXU_BIT_FOUR    4'h4
`define TXU_BIT_FIVE    4'h5
`define TXU_BIT_SIX     4'h6
`define TXU_BIT_SEVEN   4'h7
`define TXU_PARITY      4'h8    // Constant 1
`define TXU_STOP        4'h9    // Constant 1
`define TXU_SECOND_STOP 4'ha
// 4'hb // Unused
// 4'hc // Unused
// `define      TXU_START       4'hd    // An unused state
`define TXU_BREAK       4'he
`define TXU_IDLE        4'hf
 
module txuart(i_clk, i_reset, i_setup, i_break, i_wr, i_data, o_uart, o_busy);
        input                   i_clk, i_reset;
        input           [29:0]   i_setup;
        input                   i_break;
        input                   i_wr;
        input           [7:0]    i_data;
        output  reg             o_uart, o_busy;
 
        wire    [27:0]   clocks_per_baud, break_condition;
        wire    [1:0]    data_bits;
        wire            use_parity, parity_even, dblstop, fixd_parity;
        reg     [29:0]   r_setup;
        assign  clocks_per_baud = { 4'h0, r_setup[23:0] };
        assign  break_condition = { r_setup[23:0], 4'h0 };
        assign  data_bits   = r_setup[29:28];
        assign  dblstop     = r_setup[27];
        assign  use_parity  = r_setup[26];
        assign  fixd_parity = r_setup[25];
        assign  parity_even = r_setup[24];
 
        reg     [27:0]   baud_counter;
        reg     [3:0]    state;
        reg     [7:0]    lcl_data;
        reg             calc_parity;
 
        initial o_uart = 1'b1;
        initial o_busy = 1'b1;
        initial state  = `TXU_IDLE;
        // initial      baud_counter = clocks_per_baud;
        always @(posedge i_clk)
        begin
                if (i_reset)
                begin
                        baud_counter <= clocks_per_baud;
                        o_uart <= 1'b1;
                        o_busy <= 1'b1;
                        state <= `TXU_IDLE;
                        lcl_data <= 8'h0;
                        calc_parity <= 1'b0;
                end else if (i_break)
                begin
                        baud_counter <= break_condition;
                        o_uart <= 1'b0;
                        state <= `TXU_BREAK;
                        calc_parity <= 1'b0;
                        o_busy <= 1'b1;
                end else if (baud_counter != 0)
                begin // o_busy needs to be set coming into here
                        baud_counter <= baud_counter - 28'h01;
                        o_busy <= 1'b1;
                end else if (state == `TXU_BREAK)
                begin
                        state <= `TXU_IDLE;
                        o_busy <= 1'b1;
                        o_uart <= 1'b1;
                        calc_parity <= 1'b0;
                        // Give us two stop bits before becoming available
                        baud_counter <= clocks_per_baud<<2;
                end else if (state == `TXU_IDLE)        // STATE_IDLE
                begin
                        // baud_counter <= 0;
                        r_setup <= i_setup;
                        calc_parity <= 1'b0;
                        if ((i_wr)&&(~o_busy))
                        begin   // Immediately start us off with a start bit
                                o_uart <= 1'b0;
                                o_busy <= 1'b1;
                                case(data_bits)
                                2'b00: state <= `TXU_BIT_ZERO;
                                2'b01: state <= `TXU_BIT_ONE;
                                2'b10: state <= `TXU_BIT_TWO;
                                2'b11: state <= `TXU_BIT_THREE;
                                endcase
                                lcl_data <= i_data;
                                baud_counter <= clocks_per_baud-28'h01;
                        end else begin // Stay in idle
                                o_uart <= 1'b1;
                                o_busy <= 0;
                                // lcl_data is irrelevant
                                // state <= state;
                        end
                end else begin
                        // One clock tick in each of these states ...
                        baud_counter <= clocks_per_baud - 28'h01;
                        o_busy <= 1'b1;
                        if (state[3] == 0) // First 8 bits
                        begin
                                o_uart <= lcl_data[0];
                                calc_parity <= calc_parity ^ lcl_data[0];
                                if (state == `TXU_BIT_SEVEN)
                                        state <= (use_parity)?`TXU_PARITY:`TXU_STOP;
                                else
                                        state <= state + 1;
                                lcl_data <= { 1'b0, lcl_data[7:1] };
                        end else if (state == `TXU_PARITY)
                        begin
                                state <= `TXU_STOP;
                                if (fixd_parity)
                                        o_uart <= parity_even;
                                else
                                        o_uart <= calc_parity^((parity_even)? 1'b1:1'b0);
                        end else if (state == `TXU_STOP)
                        begin // two stop bit(s)
                                o_uart <= 1'b1;
                                if (dblstop)
                                        state <= `TXU_SECOND_STOP;
                                else
                                        state <= `TXU_IDLE;
                                calc_parity <= 1'b0;
                        end else // `TXU_SECOND_STOP and default:
                        begin
                                state <= `TXU_IDLE; // Go back to idle
                                o_uart <= 1'b1;
                                // Still o_busy, since we need to wait
                                // for the baud clock to finish counting
                                // out this last bit.
                        end
                end
        end
 
endmodule
 
 
 
 

Line No.	Rev	Author	Line
1	7	dgisselq	`////////////////////////////////////////////////////////////////////////////////`
2	2	dgisselq	`//`
3			`// Filename: txuart.v`
4			`//`
5	7	dgisselq	`// Project: XuLA2 board`
6	2	dgisselq	`//`
7			`// Purpose: Transmit outputs over a single UART line.`
8			`//`
9			`// To interface with this module, connect it to your system clock,`
10			`// pass it the 32 bit setup register (defined below) and the byte`
11			`// of data you wish to transmit. Strobe the i_wr line high for one`
12			`// clock cycle, and your data will be off. Wait until the 'o_busy'`
13			`// line is low before strobing the i_wr line again--this implementation`
14			`// has NO BUFFER, so strobing i_wr while the core is busy will just`
15			`// cause your data to be lost. The output will be placed on the o_txuart`
16			`// output line. If you wish to set/send a break condition, assert the`
17			`// i_break line otherwise leave it low.`
18			`//`
19			`// There is a synchronous reset line, logic high.`
20			`//`
21			`// Now for the setup register. The register is 32 bits, so that this`
22			`// UART may be set up over a 32-bit bus.`
23			`//`
24			`// i_setup[29:28] Indicates the number of data bits per word. This will`
25			`// either be 2'b00 for an 8-bit word, 2'b01 for a 7-bit word, 2'b10`
26			`// for a six bit word, or 2'b11 for a five bit word.`
27			`//`
28			`// i_setup[27] Indicates whether or not to use one or two stop bits.`
29			`// Set this to one to expect two stop bits, zero for one.`
30			`//`
31			`// i_setup[26] Indicates whether or not a parity bit exists. Set this`
32			`// to 1'b1 to include parity.`
33			`//`
34			`// i_setup[25] Indicates whether or not the parity bit is fixed. Set`
35			`// to 1'b1 to include a fixed bit of parity, 1'b0 to allow the`
36			`// parity to be set based upon data. (Both assume the parity`
37			`// enable value is set.)`
38			`//`
39			`// i_setup[24] This bit is ignored if parity is not used. Otherwise,`
40			`// in the case of a fixed parity bit, this bit indicates whether`
41			`// mark (1'b1) or space (1'b0) parity is used. Likewise if the`
42			`// parity is not fixed, a 1'b1 selects even parity, and 1'b0`
43			`// selects odd.`
44			`//`
45			`// i_setup[23:0] Indicates the speed of the UART in terms of clocks.`
46			`// So, for example, if you have a 200 MHz clock and wish to`
47			`// run your UART at 9600 baud, you would take 200 MHz and divide`
48			`// by 9600 to set this value to 24'd20834. Likewise if you wished`
49			`// to run this serial port at 115200 baud from a 200 MHz clock,`
50			`// you would set the value to 24'd1736`
51			`//`
52			`// Thus, to set the UART for the common setting of an 8-bit word,`
53			`// one stop bit, no parity, and 115200 baud over a 200 MHz clock, you`
54			`// would want to set the setup value to:`
55			`//`
56			`// 32'h0006c8 // For 115,200 baud, 8 bit, no parity`
57			`// 32'h005161 // For 9600 baud, 8 bit, no parity`
58			`//`
59	7	dgisselq	`//`
60			`//`
61			`// Creator: Dan Gisselquist, Ph.D.`
62	2	dgisselq	`// Gisselquist Technology, LLC`
63			`//`
64	7	dgisselq	`////////////////////////////////////////////////////////////////////////////////`
65	2	dgisselq	`//`
66	7	dgisselq	`// Copyright (C) 2015, Gisselquist Technology, LLC`
67	2	dgisselq	`//`
68	7	dgisselq	`// This program is free software (firmware): you can redistribute it and/or`
69			`// modify it under the terms of the GNU General Public License as published`
70			`// by the Free Software Foundation, either version 3 of the License, or (at`
71			`// your option) any later version.`
72	2	dgisselq	`//`
73	7	dgisselq	`// This program is distributed in the hope that it will be useful, but WITHOUT`
74			`// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or`
75			`// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License`
76			`// for more details.`
77	2	dgisselq	`//`
78	7	dgisselq	`// License: GPL, v3, as defined and found on www.gnu.org,`
79			`// http://www.gnu.org/licenses/gpl.html`
80	2	dgisselq	`//`
81	7	dgisselq	`//`
82			`////////////////////////////////////////////////////////////////////////////////`
83			`//`
84			`//`
85			`//`
86	2	dgisselq	`define TXU_BIT_ZERO 4'h0
87			`define TXU_BIT_ONE 4'h1
88			`define TXU_BIT_TWO 4'h2
89			`define TXU_BIT_THREE 4'h3
90			`define TXU_BIT_FOUR 4'h4
91			`define TXU_BIT_FIVE 4'h5
92			`define TXU_BIT_SIX 4'h6
93			`define TXU_BIT_SEVEN 4'h7
94			`define TXU_PARITY 4'h8 // Constant 1
95			`define TXU_STOP 4'h9 // Constant 1
96			`define TXU_SECOND_STOP 4'ha
97			`// 4'hb // Unused`
98			`// 4'hc // Unused`
99			// `define TXU_START 4'hd // An unused state
100			`define TXU_BREAK 4'he
101			`define TXU_IDLE 4'hf
102
103			`module txuart(i_clk, i_reset, i_setup, i_break, i_wr, i_data, o_uart, o_busy);`
104			`input i_clk, i_reset;`
105			`input [29:0] i_setup;`
106			`input i_break;`
107			`input i_wr;`
108			`input [7:0] i_data;`
109			`output reg o_uart, o_busy;`
110
111			`wire [27:0] clocks_per_baud, break_condition;`
112			`wire [1:0] data_bits;`
113			`wire use_parity, parity_even, dblstop, fixd_parity;`
114			`reg [29:0] r_setup;`
115			`assign clocks_per_baud = { 4'h0, r_setup[23:0] };`
116			`assign break_condition = { r_setup[23:0], 4'h0 };`
117			`assign data_bits = r_setup[29:28];`
118			`assign dblstop = r_setup[27];`
119			`assign use_parity = r_setup[26];`
120			`assign fixd_parity = r_setup[25];`
121			`assign parity_even = r_setup[24];`
122
123			`reg [27:0] baud_counter;`
124			`reg [3:0] state;`
125			`reg [7:0] lcl_data;`
126			`reg calc_parity;`
127
128			`initial o_uart = 1'b1;`
129			`initial o_busy = 1'b1;`
130			initial state = `TXU_IDLE;
131			`// initial baud_counter = clocks_per_baud;`
132			`always @(posedge i_clk)`
133			`begin`
134			`if (i_reset)`
135			`begin`
136			`baud_counter <= clocks_per_baud;`
137			`o_uart <= 1'b1;`
138			`o_busy <= 1'b1;`
139			state <= `TXU_IDLE;
140			`lcl_data <= 8'h0;`
141			`calc_parity <= 1'b0;`
142			`end else if (i_break)`
143			`begin`
144			`baud_counter <= break_condition;`
145			`o_uart <= 1'b0;`
146			state <= `TXU_BREAK;
147			`calc_parity <= 1'b0;`
148			`o_busy <= 1'b1;`
149			`end else if (baud_counter != 0)`
150			`begin // o_busy needs to be set coming into here`
151	9	dgisselq	`baud_counter <= baud_counter - 28'h01;`
152	2	dgisselq	`o_busy <= 1'b1;`
153			end else if (state == `TXU_BREAK)
154			`begin`
155			state <= `TXU_IDLE;
156			`o_busy <= 1'b1;`
157			`o_uart <= 1'b1;`
158			`calc_parity <= 1'b0;`
159			`// Give us two stop bits before becoming available`
160			`baud_counter <= clocks_per_baud<<2;`
161			end else if (state == `TXU_IDLE) // STATE_IDLE
162			`begin`
163			`// baud_counter <= 0;`
164			`r_setup <= i_setup;`
165			`calc_parity <= 1'b0;`
166			`if ((i_wr)&&(~o_busy))`
167			`begin // Immediately start us off with a start bit`
168			`o_uart <= 1'b0;`
169			`o_busy <= 1'b1;`
170			`case(data_bits)`
171			2'b00: state <= `TXU_BIT_ZERO;
172			2'b01: state <= `TXU_BIT_ONE;
173			2'b10: state <= `TXU_BIT_TWO;
174			2'b11: state <= `TXU_BIT_THREE;
175			`endcase`
176			`lcl_data <= i_data;`
177			`baud_counter <= clocks_per_baud-28'h01;`
178			`end else begin // Stay in idle`
179			`o_uart <= 1'b1;`
180			`o_busy <= 0;`
181			`// lcl_data is irrelevant`
182			`// state <= state;`
183			`end`
184			`end else begin`
185			`// One clock tick in each of these states ...`
186			`baud_counter <= clocks_per_baud - 28'h01;`
187			`o_busy <= 1'b1;`
188			`if (state[3] == 0) // First 8 bits`
189			`begin`
190			`o_uart <= lcl_data[0];`
191			`calc_parity <= calc_parity ^ lcl_data[0];`
192			if (state == `TXU_BIT_SEVEN)
193			state <= (use_parity)?`TXU_PARITY:`TXU_STOP;
194			`else`
195			`state <= state + 1;`
196			`lcl_data <= { 1'b0, lcl_data[7:1] };`
197			end else if (state == `TXU_PARITY)
198			`begin`
199			state <= `TXU_STOP;
200			`if (fixd_parity)`
201			`o_uart <= parity_even;`
202			`else`
203			`o_uart <= calc_parity^((parity_even)? 1'b1:1'b0);`
204			end else if (state == `TXU_STOP)
205			`begin // two stop bit(s)`
206			`o_uart <= 1'b1;`
207			`if (dblstop)`
208			state <= `TXU_SECOND_STOP;
209			`else`
210			state <= `TXU_IDLE;
211			`calc_parity <= 1'b0;`
212			end else // `TXU_SECOND_STOP and default:
213			`begin`
214			state <= `TXU_IDLE; // Go back to idle
215			`o_uart <= 1'b1;`
216			`// Still o_busy, since we need to wait`
217			`// for the baud clock to finish counting`
218			`// out this last bit.`
219			`end`
220			`end`
221			`end`
222
223			`endmodule`
224
225
226
227

Browse

Tools

Subversion Repositories xulalx25soc

[/] [xulalx25soc/] [trunk/] [rtl/] [txuart.v] - Blame information for rev 46